DIM800NSM33-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. 1/10
www.dynexsemi.com
FEATURES
■10µs Short Circuit Withstand
■High Thermal Cycling Capability
■Non Punch Through Silicon
■Isolated MMC Base with AlN Substrates
APPLICATIONS
■High Reliability Inverters
■Motor Controllers
■Traction Drives
■Choppers
The Powerline range of high power modules includes half
bridge, chopper, dual and single switch configurations covering
voltages from 600V to 3300V and currents up to 2400A.
The DIM800NSM33-A000 is a single switch 3300V, n
channel enhancement mode, insulated gate bipolar transistor
(IGBT) module. The IGBT has a wide reverse bias safe
operating area (RBSOA) plus full 10µs short circuit withstand.
This device is optimised for traction drives and other applications
requiring high thermal cycling capability.
The module incorporates an electrically isolated base plate
and low inductance construction enabling circuit designers to
optimise circuit layouts and utilise grounded heat sinks for safety.
ORDERING INFORMATION
Order As:
DIM800NSM33-A000
Note: When ordering, please use the whole part number.
KEY PARAMETERS
VCES 3300V
VCE(sat) (typ) 3.2V
IC(max) 800A
IC(PK) (max) 1600A
DIM800NSM33-A000
Single Switch IGBT Module
Preliminary Information
Replaces August 2001, version DS5486-1.4 DS5486-2.0 October 2001
Fig. 1 Single switch circuit diagram
Fig. 2 Electrical connections - (not to scale)
Outline type code: N
(See package details for further information)
C1
E1
C2
E2
G
E
2
C
1
E
2
- Aux Emitter
C
1
- Aux Collector
C2C1
Aux C
G
Aux E E1 E2
External connection
External connection
DIM800NSM33-A000
2/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
ABSOLUTE MAXIMUM RATINGS
Stresses above those listed under 'Absolute Maximum Ratings' may cause permanent damage to the device. In extreme
conditions, as with all semiconductors, this may include potentially hazardous rupture of the package. Appropriate safety
precautions should always be followed. Exposure to Absolute Maximum Ratings may affect device reliability.
Tcase = 25˚C unless stated otherwise
Test Conditions
VGE = 0V
-
Tcase = 80˚C
1ms, Tcase = 115˚C
Tcase = 25˚C, Tj = 150˚C
VR = 0, tp = 10ms, Tvj = 125˚C
Commoned terminals to base plate. AC RMS, 1 min, 50Hz
IEC1287. V1 = 2450V, V2 = 1800V, 50Hz RMS
Symbol
VCES
VGES
IC
IC(PK)
Pmax
I2t
Visol
QPD
Units
V
V
A
A
kW
kA2s
V
pC
Max.
3300
±20
800
1600
9.6
320
6000
10
Parameter
Collector-emitter voltage
Gate-emitter voltage
Continuous collector current
Peak collector current
Max. transistor power dissipation
Diode I2t value (Diode arm)
Isolation voltage - per module
Partial discharge - per module
DIM800NSM33-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. 3/10
www.dynexsemi.com
THERMAL AND MECHANICAL RATINGS
Internal insulation material: AlN
Baseplate material: AlSiC
Creepage distance: 33mm
Clearance: 20mm
CTI (Critical Tracking Index): 175
Test Conditions
Continuous dissipation -
junction to case
Continuous dissipation -
junction to case
Mounting torque 5Nm
(with mounting grease)
Transistor
Diode
-
Mounting - M6
Electrical connections - M4
Electrical connections - M8
Parameter
Thermal resistance - transistor (per switch)
Thermal resistance - diode (per switch)
Thermal resistance - case to heatsink
(per module)
Junction temperature
Storage temperature range
Screw torque
Symbol
Rth(j-c)
Rth(j-c)
Rth(c-h)
Tj
Tstg
-
Units
˚C/kW
˚C/kW
˚C/kW
˚C/kW
˚C
˚C
˚C
Nm
Nm
Nm
Max.
13
26
6
150
125
125
5
2
10
Typ.
-
-
-
-
-
-
-
-
-
Min.
-
-
-
-
-
–40
-
-
-
DIM800NSM33-A000
4/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
ELECTRICAL CHARACTERISTICS
Tcase = 25˚C unless stated otherwise.
Test Conditions
VGE = 0V, VCE = VCES
VGE = 0V, VCE = VCES, Tcase = 125˚C
VGE = ±20V, VCE = 0V
IC = 80mA, VGE = VCE
VGE = 15V, IC = 800A
VGE = 15V, IC = 800A, , Tcase = 125˚C
DC
tp = 1ms
IF = 800A
IF = 800A, Tcase = 125˚C
VCE = 25V, VGE = 0V, f = 1MHz
VCE = 25V, VGE = 0V, f = 1MHz
-
-
T
j
= 125˚C, V
CC
= 2500V,
I1
t
p
≤ 10µs,
V
CE(max)
= V
CES
– L*. di/dt
I2
IEC 60747-9
Parameter
Collector cut-off current
Gate leakage current
Gate threshold voltage
Collector-emitter saturation voltage
Diode forward current
Diode maximum forward current
Diode forward voltage
Input capacitance
Reverse transfer capacitance
Module inductance
Internal transistor resistance
Short circuit. ISC
Symbol
ICES
IGES
VGE(TH)
VCE(sat)
IF
IFM
VF
Cies
Cres
LM
RINT
SCData
Units
mA
mA
µA
V
V
V
A
A
V
V
nF
nF
nH
mΩ
A
A
Max.
4
60
8
6.5
-
-
-
-
-
-
-
-
-
-
-
Typ.
-
-
-
5.5
3.2
4.0
800
1600
2.5
2.5
180
10
11
0.135
5200
4400
Min.
-
-
-
4.5
-
-
-
-
-
-
-
-
-
-
-
Note:
L* is the circuit inductance + LM
DIM800NSM33-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. 5/10
www.dynexsemi.com
Units
ns
ns
mJ
ns
ns
mJ
µC
µC
A
mJ
Max.
-
-
-
-
-
-
-
-
-
-
Typ.
1600
200
850
500
300
1000
24
450
650
500
Min.
-
-
-
-
-
-
-
-
-
-
Test Conditions
IC = 800A
VGE = ±15V
VCE = 1800V
RG(ON) = RG(OFF) = 2.2Ω
Cge = 150nF
L ~ 100nH
IF = 800A, VCE = 1800V,
dIF/dt = 4400A/µs
Parameter
Turn-off delay time
Fall time
Turn-off energy loss
Turn-on delay time
Rise time
Turn-on energy loss
Gate charge
Diode reverse recovery charge
Diode reverse recovery current
Diode reverse recovery energy
ELECTRICAL CHARACTERISTICS
Tcase = 25˚C unless stated otherwise
Symbol
td(off)
tf
EOFF
td(on)
tr
EON
Qg
Qrr
Irr
Erec
Tcase = 125˚C unless stated otherwise
Units
ns
ns
mJ
ns
ns
mJ
µC
A
mJ
Max.
-
-
-
-
-
-
-
-
-
Typ.
1800
250
1000
500
300
1300
670
670
850
Min.
-
-
-
-
-
-
-
-
-
Test Conditions
IC = 800A
VGE = ±15V
VCE = 1800V
RG(ON) = RG(OFF) = 2.2Ω
Cge = 150nF
L ~ 100nH
IF = 800A, VCE = 1800V,
dIF/dt = 3000A/µs
Parameter
Turn-off delay time
Fall time
Turn-off energy loss
Turn-on delay time
Rise time
Turn-on energy loss
Diode reverse recovery charge
Diode reverse recovery current
Diode reverse recovery energy
Symbol
td(off)
tf
EOFF
td(on)
tr
EON
Qrr
Irr
Erec
DIM800NSM33-A000
6/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
TYPICAL CHARACTERISTICS
Fig. 3 Typical output characteristics Fig. 4 Typical output characteristics
Fig. 5 Typical switching energy vs collector current Fig. 6 Typical switching energy vs gate resistance
0
200
400
600
800
1000
1200
1400
1600
0Collector-emitter voltage, Vce - (V)
Collector current, I
C
- (A)
654321
V
GE
= 20V
V
GE
= 15V
V
GE
= 12V
V
GE
= 10V
Common emitter.
T
case
= 25˚C
0
200
400
600
800
1000
1200
1400
1600
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5 8
Collector-emitter voltage, Vce - (V)
Collector current, IC - (A)
VGE = 20V
VGE = 15V
VGE = 12V
VGE = 10V
Common emitter.
Tcase = 125˚C
0
200
400
600
800
1000
1200
1400
0 200 400 600 800 1000
Collector current, Ic - (A)
Switching energy, Esw - (mJ)
Eon
Eoff
Erec
Conditions:
Tcase = 125˚C
Rg = 2.2 Ohms
Vcc = 1800V
Cge = 150nF
0
200
400
600
800
1000
1200
1400
1600
1800
2000
2 2.5 3 3.5 4 4.5 5
Gate resistance, R
g
- (Ohms)
Switching energy, E
sw
- (mJ)
E
on
E
off
E
rec
Conditions:
T
case
= 125˚C
I
C
= 800A
V
cc
= 1800V
C
ge
= 150nF
DIM800NSM33-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. 7/10
www.dynexsemi.com
Fig. 7 Diode typical forward characteristics Fig. 8 Reverse bias safe operating area
Fig. 9 Diode reverse bias safe operating area Fig. 10 Forward bias safe operating area
0
200
400
600
800
1000
1200
1400
1600
0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
Forward voltage, V
F
- (V)
Forward current, I
F
- (A)
T
j
= 25˚C
T
j
= 125˚C
0
200
400
600
800
1000
1200
1400
1600
1800
0 500 1000 1500 2000 2500 3000 3500
Collector emitter voltage, V
ce
- (V)
Collector current, I
C
- (A)
T
case
= 125˚C
V
ge
= ±15V
R
g(min)
= 2.2Ω
Module
Chip
0
200
400
600
800
1000
1200
1400
0 500 1000 1500 2000 2500 3000 3500
Reverse voltage, V
R
- (V)
Reverse recovery current, I
rr
- (A)
0
1
10
100
1000
10000
1 10 100 1000 10000
Collector emitter voltage, V
ce
- (V)
Collector Current, I
C
- (A)
I
C(max)
DC
t
p
= 1 ms
t
p
= 100µs
t
p
= 50µs
T
vj
= 125˚C, T
c
= 80˚C
DIM800NSM33-A000
8/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
Fig. 11 Transient thermal impedance Fig. 12 DC current rating vs case temperature
0.1
1
10
100
0.001 0.01 10.1 10
Pulse width, t
p
- (s)
Transient thermal impedance, Z
th (j-c)
- (°C/kW )
IGBT R
i
(˚C/KW)
τ
i
(ms)
Diode R
i
(˚C/KW)
τ
i
(ms)
1
0.3747
0.0876
0.7386
0.0843
2
1.9652
3.7713
3.9115
3.7205
3
2.7777
33.5693
5.5628
33.2138
4
8.4016
236.8023
16.8308
236.5275
Diode
Transistor
0
200
400
600
800
1000
1200
1400
0 20 40 60 80 100 120 140 160
Case temperature, Tcase - (˚C)
DC collector current, IC - (A)
DIM800NSM33-A000
Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures. 9/10
www.dynexsemi.com
PACKAGE DETAILS
For further package information, please visit our website or contact your nearest Customer Service Centre. All dimensions in mm, unless
stated otherwise. DO NOT SCALE.
140
31.5
4x M8
28
5
38
6x M4
45.2
40 20
43.5 18
57 57
65 65
6x Ø7
62
20
62 20
48.8
10.35
24.5
10.65
C1
E1
C2
E2
G
E
2
C
1
Main Terminal screw plastic hole depth (M8) = 16.8 ± 0.3
Auxiliary and Gate pin plastic hole depth (M4) = 9± 0.3
Copper terminal thickness, Main Terminal pins = 1.5 ± 0.1
Copper terminal thickness, Auxiliary and Gate pin = 0.9 ± 0.1
Nominal weight: 1050g
Module outline type code: N
E
2
- Aux Emitter
C
1
- Aux Collector
DIM800NSM33-A000
10/10 Caution: This device is sensitive to electrostatic discharge. Users should follow ESD handling procedures.
www.dynexsemi.com
POWER ASSEMBLY CAPABILITY
The Power Assembly group was set up to provide a support service for those customers requiring more than the basic semiconductor,
and has developed a flexible range of heatsink and clamping systems in line with advances in device voltages and current capability
of our semiconductors.
We offer an extensive range of air and liquid cooled assemblies covering the full range of circuit designs in general use today. The
Assembly group continues to offer high quality engineering support dedicated to designing new units to satisfy the growing needs of our
customers.
Using the latest CAD methods our team of design and applications engineers aim to provide the Power Assembly Complete Solution
(PACs).
HEATSINKS
The Power Assembly group has its own proprietary range of extruded aluminium heatsinks. They have been designed to optimise the
performance of Dynex semiconductors. Data with respect to air natural, forced air and liquid cooling (with flow rates) is available on
request.
For further information on device clamps, heatsinks and assemblies, please contact your nearest sales representative or customer
service office.
CUSTOMER SERVICE CENTRES
Mainland Europe Tel: +33 (0)1 58 04 91 00. Fax: +33 (0)1 46 38 51 33
North America Tel: (613) 723-7035. Fax: (613) 723-1518.
UK, Scandinavia & Rest Of World Tel: +44 (0)1522 502901 / 502753. Fax: +44 (0)1522 500020
SALES OFFICES
Mainland Europe Tel: +33 (0)1 58 04 91 00. Fax: +33 (0)1 46 38 51 33
North America Tel: (613) 723-7035. Fax: (613) 723-1518. Toll Free: 1.888.33.DYNEX (39639) /
Tel: (949) 733-3005. Fax: (949) 733-2986.
UK, Scandinavia & Rest Of World Tel: +44 (0)1522 502901 / 502753. Fax: +44 (0)1522 500020
These offices are supported by Representatives and Distributors in many countries world-wide.
© Dynex Semiconductor 2001 Publication No. DS5486-2 Issue No. 2.0 August 2001
TECHNICAL DOCUMENTATION – NOT FOR RESALE. PRINTED IN UNITED KINGDOM
HEADQUARTERS OPERATIONS
DYNEX SEMICONDUCTOR LTD
Doddington Road, Lincoln.
Lincolnshire. LN6 3LF. United Kingdom.
Tel: 00-44-(0)1522-500500
Fax: 00-44-(0)1522-500550
DYNEX POWER INC.
99 Bank Street, Suite 410,
Ottawa, Ontario, Canada, K1P 6B9
Tel: 613.723.7035
Fax: 613.723.1518
Toll Free: 1.888.33.DYNEX (39639)
This publication is issued to provide information only which (unless agreed by the Company in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as
a representation relating to the products or services concerned. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. The Company reserves
the right to alter without prior notice the specification, design or price of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such
methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication
or data used is up to date and has not been superseded. These products are not suitable for use in any medical products whose failure to perform may result in significant injury
or death to the user. All products and materials are sold and services provided subject to the Company's conditions of sale, which are available on request.
All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their respective owners.
http://www.dynexsemi.com
e-mail: power_solutions@dynexsemi.com
Datasheet Annotations:
Dynex Semiconductor annotate datasheets in the top right hard corner of the front page, to indicate product status. The annotations are as follows:-
Target Information: This is the most tentative form of information and represents a very preliminary specification. No actual design work on the product has been started.
Preliminary Information: The product is in design and development. The datasheet represents the product as it is understood but details may change.
Advance Information: The product design is complete and final characterisation for volume production is well in hand.
No Annotation: The product parameters are fixed and the product is available to datasheet specification.
