ADC12040 ADC12040 12-Bit, 40 MSPS, 340mW A/D Converter with Internal Sample-and-Hold Literature Number: SNAS135F ADC12040 12-Bit, 40 MSPS, 340mW A/D Converter with Internal Sample-and-Hold General Description Features The ADC12040 is a monolithic CMOS analog-to-digital converter capable of converting analog input signals into 12-bit digital words at 40 Megasamples per second (MSPS), minimum. This converter uses a differential, pipeline architecture with digital error correction and an on-chip sample-and-hold circuit to minimize die size and power consumption while providing excellent dynamic performance. Operating on a single 5V power supply, this device consumes just 340 mW at 40 MSPS, including the reference current. The Power Down feature reduces power consumption to 40 mW. The differential inputs provide a full scale differential input swing equal to 2VREF with the possibility of a single-ended input, although full use of the differential input is required for optimum performance. For ease of use, the buffered, high impedance, single-ended reference input is converted onchip to a differential reference for use by the processing circuitry. Output data format is 12-bit offset binary. This device is available in the 32-lead LQFP package and will operate over the industrial temperature range of -40C to +85C. Single +5V supply operation Internal sample-and-hold Outputs 2.35V to 5V compatible Pin Compatible with ADC12010, ADC12020, ADC12L063, ADC12L066 Power down mode On-chip reference buffer Key Specifications Supply Voltage DNL SNR (fIN = 10MHz) ENOB (fIN = 10MHz) Power Consumption, 40 MHz +5V 5% 0.4 LSB (typ) 69 dB (typ) 11.2 bits (typ) 340 mW (typ) Applications Ultrasound and Imaging Instrumentation Cellular Base Stations/Communications Receivers Sonar/Radar xDSL Wireless Local Loops/Cable Modems HDTV/DTV DSP Front Ends Connection Diagram 20014801 (c) 2008 National Semiconductor Corporation 200148 www.national.com ADC12040 12-Bit, 40 MSPS, 340mW A/D Converter with Internal Sample-and-Hold July 28, 2008 ADC12040 Ordering Information Industrial (-40C TA +85C) Package ADC12040CIVY 32 Pin LQFP ADC12040CIVYX 32 Pin LQFP Tape and Reel ADC12040EVAL Evaluation Board Block Diagram 20014802 www.national.com 2 ADC12040 Pin Descriptions and Equivalent Circuits Pin No. Symbol Equivalent Circuit Description ANALOG I/O VIN+ Non-Inverting analog signal Input. With a 2.0V reference voltage, the ground-referenced input signal level is 2.0 VP-P centered on VCM. 3 VIN- Inverting analog signal Input. With a 2.0V reference voltage the ground-referenced input signal level is 2.0 VP-P centered on VCM. This pin may be connected to VCM for single-ended operation, but a differential input signal is required for best performance. 1 VREF Reference input. This pin should be bypassed to ground with a 0.1 F monolithic capacitor. VREF is 2.0V nominal and should be between 1.0V to 2.4V. 31 VRP 32 VRM 30 VRN 2 These pins are high impedance reference bypass pins. Connect a 0.1 F capacitor from each of these pins to AGND. DO NOT load these pins. DIGITAL I/O 10 CLK Digital clock input. The input is sampled on the rising edge of CLK. 11 OE OE is the output enable pin that, when low, enables the TRISTATETM data output pins. When this pin is high, the outputs are in a high impedance state. 8 PD PD is the Power Down input pin. When high, this input puts the converter into the power down mode. When this pin is low, the converter is in the active mode. 14-19, 22- 27 D0-D11 Digital data output pins that make up the 12-bit conversion results. D0 is the LSB, while D11 is the MSB of the offset binary output word. Output levels are TTL/CMOS compatible. 3 www.national.com ADC12040 Pin No. Symbol Equivalent Circuit Description ANALOG POWER 5, 6, 29 VA 4, 7, 28 AGND Positive analog supply pins. These pins should be connected to a quiet +5V voltage source and bypassed to ground with 0.1 F monolithic capacitors located within 1 cm of these power pins, and with a 10 F capacitor. The ground return for the analog supply. DIGITAL POWER 13 VD 9, 12 DGND 21 20 www.national.com Positive digital supply pin. This pin should be connected to the same quiet +5V source as is VA and bypassed to ground with a 0.1 F monolithic capacitor in parallel with a 10 F capacitor, both located within 1 cm of the power pin. The ground return for the digital supply. VDR Positive digital supply pin for the ADC12040's output drivers. This pin should be connected to a voltage source of +2.35V to +5V and be bypassed to DR GND with a 0.1 F monolithic capacitor. If the supply for this pin is different from the supply used for VA and VD, it should also be bypassed with a 10 F tantalum capacitor. VDR should never exceed the voltage on VD. All bypass capacitors should be located within 1 cm of the supply pin. DR GND The ground return for the digital supply for the ADC12040's output drivers. This pin should be connected to the system ground, but not be connected in close proximity to the ADC12040's DGND or AGND pins. See Section 5 (Layout and Grounding) for more details. 4 Operating Ratings (Notes 1, 2) Operating Temperature If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VA, VD) Output Driver Supply (VDR) VREF Input VCM Input CLK, PD, OE VIN Input |AGND-DGND| VA, VD, VDR |VA-VD| 6.5V Voltage on Any Input or Output Pin Input Current at Any Pin (Note 3) Package Input Current (Note 3) Package Dissipation at TA = 25C ESD Susceptibility Human Body Model (Note 5) Machine Model (Note 5) Soldering Temperature, Infrared, 10 sec. (Note 6) Storage Temperature 100 mV -0.3V to (VA or VD +0.3V) 25 mA 50 mA See (Note 4) (Notes 1, 2) -40C TA +85C +4.75V to +5.25V +2.35V to VD 1.0V to 2.2V 0.5V to 3.0V -0.05V to (VD + 0.05V) -0V to (VA - 1.0V) 100mV Package Thermal Resistance Package JA 32-Lead LQFP 79C / W 2500V 250V 235C -65C to +150C Converter Electrical Characteristics Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +5V, VDR = +3.0V, PD = 0V, VREF = +2.0V, fCLK = 40 MHz, tr = tf = 3 ns, CL = 20 pF/pin. Boldface limits apply for TA = TJ = TMIN to TMAX: all other limits TA = TJ = 25C (Notes 7, 8, 9) Symbol Parameter Conditions Typical (Note 10) Limits (Note 10) Units (Limits) STATIC CONVERTER CHARACTERISTICS 12 Bits (min) INL Resolution with No Missing Codes Integral Non Linearity (Note 11) 0.7 1.8 LSB (max) DNL Differential Non Linearity 0.4 1.0 LSB (max) GE Gain Error 0.1 2.1 %FS (max) Offset Error (VIN+ = VIN-) %FS (max) -0.1 0.9 Under Range Output Code 0 0 Over Range Output Code 4095 4095 DYNAMIC CONVERTER CHARACTERISTICS FPBW Full Power Bandwidth SNR Signal-to-Noise Ratio SINAD Signal-to-Noise and Distortion ENOB Effective Number of Bits THD Total Harmonic Distortion SFDR Spurious Free Dynamic Range IMD Intermodulation Distortion 0 dBFS Input, Output at -3 dB fIN 1 MHz, VIN -0.5 dBFS 100 70 fIN = 10 MHz, VIN = -0.5 dBFS 69.5 fIN = 1 MHz, VIN = -0.5 dBFS 69.5 fIN = 10 MHz, VIN = -0.5 dBFS 69 fIN = 1 MHz, VIN = -0,5 dBFS 11.2 fIN = 10 MHz, VIN = -0,5 dBFS 11.2 fIN = 1 MHz, VIN = -0,5 dBFS -82 fIN = 10 MHz, VIN = -0,5 dBFS -80 fIN = 1 MHz, VIN = -0,5 dBFS 86 fIN = 10 MHz, VIN = -0.5 dBFS 84 fIN = 9.5 MHz and 10.5 MHz, each = -8 dBFS -75 5 MHz dB 66.5 dB (min) 66 dB (min) 10.7 Bits (min) -67 dB (max) 68 dB (min) dB Bits dB dB dBFS www.national.com ADC12040 Absolute Maximum Ratings ADC12040 Symbol Parameter Typical (Note 10) Conditions Limits (Note 10) Units (Limits) REFERENCE AND ANALOG INPUT CHARACTERISTICS VCM CIN VREF VA/2 V (CLK LOW) 8 pF (CLK HIGH) 7 Common Mode Input Voltage VIN Input Capacitance (each pin to GND) VIN = 2.5 Vdc + 0.7 Vrms Reference Voltage (Note 13) 2.00 Reference Input Resistance 100 pF 1.0 2.2 V (min) V (max) M (min) DC and Logic Electrical Characteristics Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +5V, VDR = +3.0V, PD = 0V, VREF = +2.0V, fCLK = 40 MHz, tr = tf = 3 ns, CL = 20 pF/pin. Boldface limits apply for TA = TJ = TMIN to TMAX: all other limits TA = TJ = 25C (Notes 7, 8, 9) Symbol Parameter Conditions Typical Limits (Note 10) (Note 10) Units (Limits) CLK, PD, OE DIGITAL INPUT CHARACTERISTICS VIN(1) Logical "1" Input Voltage VD = 5.25V 2.0 V (min) VIN(0) Logical "0" Input Voltage VD = 4.75V 1.0 V (max) IIN(1) Logical "1" Input Current VIN = 5.0V 10 A IIN(0) Logical "0" Input Current VIN = 0V -10 A CIN Digital Input Capacitance 5 pF D0-D11 DIGITAL OUTPUT CHARACTERISTICS VOUT(1) Logical "1" Output Voltage IOUT = -0.5 mA VOUT(0) Logical "0" Output Voltage IOUT = 1.6 mA, VDR = 3V VDR = 2.5V 2.3 V (min) VDR = 3V 2.7 V (min) 0.4 V (max) VOUT = 2.5V or 5V 100 nA IOZ TRI-STATE Output Current VOUT = 0V -100 nA +ISC Output Short Circuit Source Current VOUT = 0V -20 mA (min) -ISC Output Short Circuit Sink Current VOUT = VDR 20 mA (min) POWER SUPPLY CHARACTERISTICS IA Analog Supply Current PD Pin = DGND, VREF = 2.0V PD Pin = VDR 59 8 66 mA (max) mA ID Digital Supply Current PD Pin = DGND PD Pin = VDR, fCLK = 0 6 0 7.3 mA (max) mA IDR Digital Output Supply Current PD Pin = DGND, CL = 0 pF (Note 14) PD Pin = VDR, fCLK = 0 3 0 Total Power Consumption PD Pin = DGND, CL = 0 pF (Note 15) PD Pin = VDR, fCLK = 0 340 40 PSRR1 Power Supply Rejection Rejection of Full-Scale Error with VA = 4.75V vs. 5.25V 58 dB PSRR2 Power Supply Rejection SNR Degradation w/10 MHz, 200 mVP-P riding on VA 50 dB www.national.com 6 mA (max) mA 366 mW mW Unless otherwise specified, the following specifications apply for AGND = DGND = DR GND = 0V, VA = VD = +5V, VDR = +3.0V, PD = 0V, VREF = +2.0V, fCLK = 40 MHz, tr = tf = 3 ns, CL = 20 pF/pin. Boldface limits apply for TA = TJ = TMIN to TMAX: all other limits TA = TJ = 25C (Notes 7, 8, 9, 12) Symbol Parameter Conditions Typical Limits (Note 10) (Note 10) Units (Limits) fCLK1 Maximum Clock Frequency 50 fCLK2 Minimum Clock Frequency 100 tCH Clock High Time 11.25 tCL Clock Low Time 11.25 ns (min) tCONV Conversion Latency 6 Clock Cycles 16.3 ns (max) 15.9 ns (max) 15.7 ns (max) 14.9 ns (max) VDR = 2.5V, -45C < TA < +85C VDR = 2.5V, TA = +25C 12 40 MHz (min) kHz ns (min) tOD Data Output Delay after Rising CLK Edge tAD Aperture Delay 1.2 ns tAJ Aperture Jitter 1.2 ps rms tDIS Data outputs into TRI-STATE Mode 4 ns tEN Data Outputs Active after TRI-STATE 4 ns tPD Power Down Mode Exit Cycle 20 tCLK VDR = 3.0V, -45C < TA < +85C VDR = 3.0V, TA = +25C 11 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. Note 2: All voltages are measured with respect to GND = AGND = DGND = 0V, unless otherwise specified. Note 3: When the input voltage at any pin exceeds the power supplies (that is, VIN < AGND, or VIN > VA), the current at that pin should be limited to 25 mA. The 50 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 25 mA to two. This note does not apply to any power or ground pin. Note 4: The absolute maximum junction temperature (TJmax) for this device is 150C. The maximum allowable power dissipation is dictated by TJmax, the junction-to-ambient thermal resistance (JA), and the ambient temperature, (TA), and can be calculated using the formula PDMAX = (TJmax - TA )/JA. The values for maximum power dissipation listed above will be reached only when the device is operated in a severe fault condition (e.g. when input or output pins are driven beyond the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided. Note 5: Human body model is 100 pF capacitor discharged through a 1.5 k resistor. Machine model is 220 pF discharged through 0. Note 6: The 235C reflow temperature refers to infrared reflow. For Vapor Phase Reflow (VPR), the following Conditions apply: Maintain the temperature at the top of the package body above 183C for a minimum 60 seconds. The temperature measured on the package body must not exceed 220C. Only one excursion above 183C is allowed per reflow cycle. Note 7: The inputs are protected as shown below. Input voltage magnitudes above VA or below GND will not damage this device, provided current is limited per (Note 3). However, errors in the A/D conversion can occur if the input goes above VA or below GND by more than 100 mV. As an example, if VA is 4.75V, the full-scale input voltage must be 4.85V to ensure accurate conversions. 20014807 Note 8: To guarantee accuracy, it is required that |VA-VD| 100 mV and separate bypass capacitors are used at each power supply pin. Note 9: With the test condition for VREF = +2.0V (4VP-P differential input), the 12-bit LSB is 977 V. Note 10: Typical figures are at TA = TJ = 25C, and represent most likely parametric norms. Test limits are guaranteed to National's AOQL (Average Outgoing Quality Level). Note 11: Integral Non Linearity is defined as the deviation of the analog value, expressed in LSBs, from the straight line that passes through positive and negative full-scale. Note 12: Timing specifications are tested at TTL logic levels, VIL = 0.4V for a falling edge and VIH = 2.4V for a rising edge. Note 13: Optimum performance will be obtained by keeping the reference input in the 1.8V to 2.2V range. The LM4051CIM3-ADJ (SOT-23 package) is recommended for this application. 7 www.national.com ADC12040 AC Electrical Characteristics ADC12040 Note 14: IDR is the current consumed by the switching of the output drivers and is primarily determined by load capacitance on the output pins, the supply voltage, VDR, and the rate at which the outputs are switching (which is signal dependent). IDR=VDR(C0 x f0 + C1 x f1 +....C11 x f11) where VDR is the output driver power supply voltage, Cn is total capacitance on the output pin, and fn is the average frequency at which that pin is toggling. Note 15: Excludes IDR. See note 14. OUTPUT DELAY is the time delay after the rising edge of the clock before the data update is presented at the output pins. PIPELINE DELAY (LATENCY) is the number of clock cycles between initiation of conversion and when that data is presented to the output driver stage. Data for any given sample is available at the output pins the Pipeline Delay plus the Output Delay after the sample is taken. New data is available at every clock cycle, but the data lags the conversion by the pipeline delay. POSITIVE FULL SCALE ERROR is the difference between the actual last code transition and its ideal value of 11/2 LSB below the reference voltage. POWER SUPPLY REJECTION RATIO (PSRR) is a measure of how well the ADC rejects a change in the power supply voltage. For the ADC12040, PSRR1 is the ratio of the change in Full-Scale Error that results from a change in the d.c. power supply voltage, expressed in dB. PSRR2 is a measure of how well an a.c. signal riding upon the power supply is rejected at the output. SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in dB, of the rms value of the input signal to the rms value of the sum of all other spectral components below one-half the sampling frequency, not including harmonics or d.c. SIGNAL TO NOISE PLUS DISTORTION (S/N+D or SINAD) Is the ratio, expressed in dB, of the rms value of the input signal to the rms value of all of the other spectral components below half the clock frequency, including harmonics but excluding d.c. SPURIOUS FREE DYNAMIC RANGE (SFDR) is the difference, expressed in dB, between the desired signal amplitude to the amplitude of the peak spurious spectral component, where a spurious spectral component is any signal present in the output spectrum that is not present at the input and may or may not be a harmonic. TOTAL HARMONIC DISTORTION (THD) is the ratio, expressed in dB or dBc, of the rms total of the first nine harmonic components to the rms value of the input signal. THD is calculated as Specification Definitions APERTURE DELAY is the time after the rising edge of the clock to when the input signal is acquired or held for conversion. APERTURE JITTER (APERTURE UNCERTAINTY) is the variation in aperture delay from sample to sample. Aperture jitter manifests itself as noise in the output. CLOCK DUTY CYCLE is the ratio of the time during one cycle that a repetitive digital waveform is high to the total time of one period. The specification here refers to the ADC clock input signal. COMMON MODE VOLTAGE (VCM) is the d.c. potential present at both signal inputs to the ADC. CONVERSION LATENCY See PIPELINE DELAY. DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1 LSB. EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE BITS) is another method of specifying Signal-to-Noise and Distortion or SINAD. ENOB is defined as (SINAD - 1.76) / 6.02 and says that the converter is equivalent to a perfect ADC of this (ENOB) number of bits. FULL POWER BANDWIDTH is a measure of the frequency at which the reconstructed output fundamental drops 3 dB below its low frequency value for a full scale input. GAIN ERROR is the deviation from the ideal slope of the transfer function. It is the difference between the Positive Full Scale Error and the Negative Full Scale Error: Gain Error = Pos. Full Scale Error - Neg. Full Scale Error INTEGRAL NON LINEARITY (INL) is a measure of the deviation of each individual code from a line drawn from negative full scale (1/2 LSB below the first code transition) through positive full scale (1/2 LSB above the last code transition). The deviation of any given code from this straight line is measured from the center of that code value. INTERMODULATION DISTORTION (IMD) is the creation of additional spectral components as a result of two sinusoidal frequencies being applied to the ADC input at the same time. It is defined as the ratio of the power in the intermodulation products to the total power in the original frequencies. IMD is usually expressed in dBFS. MISSING CODES are those output codes that will never appear at the ADC outputs. The ADC12040 is guaranteed not to have any missing codes. NEGATIVE FULL SCALE ERROR is the difference between the actual first code transition and its ideal value of 1/2 LSB above negative full scale (-VREF). OFFSET ERROR is the difference between the two input voltages [ (VIN+) - (VIN-) ] required to cause a transition from code 2047 to 2048. www.national.com where F1 is the RMS power of the fundamental (output) frequency and f2 through f10 are the RMS power of the first 9 harmonic frequencies in the output spectrum. 8 ADC12040 Timing Diagram 20014809 Output Timing Transfer Characteristic 20014810 FIGURE 1. Transfer Characteristic 9 www.national.com ADC12040 Typical Performance Characteristics VA = VD = 5V, VDR = 3V, fCLK = 40 MHz, fIN = 10 MHz unless otherwise stated DNL DNL vs. VA 20014818 20014821 DNL vs. Temperature DNL vs. Clock Duty Cycle 20014819 20014822 INL INL vs. VA 20014820 www.national.com 20014823 10 ADC12040 INL vs. Temperature INL vs. Clock Duty Cycle 20014824 20014827 SNR vs. Temperature THD vs. Temperature 20014828 20014826 SINAD vs. Temperature SNR vs. Clock Duty Cycle 20014825 20014831 11 www.national.com ADC12040 THD vs. Clock Duty Cycle SINAD and ENOB vs. Clock Duty Cycle 20014832 20014833 Spectral Response IMD @ F1 = 9.5MHz, F2 = 10.5MHz 20014829 www.national.com 20014834 12 ADC12040 VIN+, VIN- = VREF + VCM 4V Functional Description to maintain THD and SINAD performance. Operating on a single +5V supply, the ADC12040 uses a pipeline architecture and has error correction circuitry to help ensure maximum performance. The differential analog input signal is digitized to 12 bits. The reference input is buffered to ease the task of driving that pin and the output word rate is the same as the clock frequency. The analog input voltage is acquired at the rising edge of the clock and the digital data for a given sample is delayed by the pipeline for 6 clock cycles. A logic high on the power down (PD) pin reduces the converter power consumption to 40 mW. Applications Information 1.0 OPERATING CONDITIONS We recommend that the following conditions be observed for operation of the ADC12040: 4.75V VA 5.25V VD = VA 2.35V VDR VD 100 kHz fCLK 50 MHz 1.0V VREF 2.2V 0.5V VCM 3.0V 0V VIN (VA - 1.0V) VREF and VCM must be such that the signal swing remains within the limits of 0V to VA. 20014811 FIGURE 2. Expected Input Signal Range The ADC12040 performs best with a differential input with each input centered around a VCM. The peak-to-peak voltage swing at VIN+ and VIN- each should not exceed the value of the reference voltage or the output data will be clipped. The two input signals should be exactly 180 out of phase from each other and of the same amplitude. For single frequency inputs, angular errors result in a reduction of the effective full scale input. For a complex waveform, however, angular errors will result in distortion. For angular deviations of up to 10 degrees from these two signals being 180 out of phase, the full scale error in LSB can be described as approximately 1.1 Analog Inputs The ADC12040 has two signal input pins, VIN+ and VIN-, forming a differential input pair, and one reference input pin, VREF. EFS = 4096 ( 1 - sin (90 + dev)) Where dev is the angular difference, in degrees, between the two signals having a 180 relative phase relationship to each other (see Figure 3). Drive the analog inputs with a source impedance less than 100. 1.2 Reference Pins The ADC12040 is designed to operate with a 2.0V reference, but performs well with reference voltages in the range of 1.0V to 2.2V. Lower reference voltages will decrease the signal-tonoise ratio (SNR). Increasing the reference voltage (and the input signal swing) beyond 2.2V will degrade THD for a fullscale input It is important that all grounds associated with the reference voltage and the input signal make connection to the ground plane at a single point to minimize the effects of noise currents in the ground path. The three Reference Bypass Pins (VRP, VRM and VRN) are made available for bypass purposes only. These pins should each be bypassed to ground with a 0.1 F capacitor. Smaller capacitor values will allow faster recovery from the power down mode, but may result in degraded noise performance. DO NOT LOAD these pins. 20014812 FIGURE 3. Angular Errors Between the Two Input Signals Will Reduce the Output Level For differential operation, each analog input signal should have a peak-to-peak voltage equal to the input reference voltage, VREF, and be centered around a common mmode voltage, VCM. 1.3 Signal Inputs The signal inputs are VIN+ and VIN-. The input signal, VIN, is defined as TABLE 1. Input to Output Relationship - Differential Input VIN = (VIN+) - (VIN-) VIN+ VIN- Output Figure 2 shows the expected input signal range. Note that the common mode input voltage range is 1V to 3V with a nominal value of VA/2. The input signals should remain between ground and 4V. The Peaks of the individual input signals (VIN+ and VIN-) should each never exceed the voltage described as VCM - VREF/2 VCM + VREF/2 0000 0000 0000 VCM - VREF/4 VCM + VREF/4 0100 0000 0000 VCM VCM 1000 0000 0000 VCM + VREF/2 VCM - VREF/4 1100 0000 0000 VCM + VREF/2 VCM - VRE/2F 1111 1111 1111 13 www.national.com ADC12040 output voltage of the LMH6550 is equal to the VCM input input voltage. TABLE 2. Input to Output Relationship - Single-Ended Input VIN+ VIN- Output VCM - VREF VCM 0000 0000 0000 VCM - VREF/2 VCM 0100 0000 0000 VCM VCM 1000 0000 0000 VCM + VREF/2 VCM 1100 0000 0000 VCM +VREF VCM 1111 1111 1111 2.0 DIGITAL INPUTS The digital TTL/CMOS compatible inputs consist of CLK, OE and PD. 2.1 The CLK Input The CLK signal controls the timing of the sampling process. Drive the clock input with a stable, low jitter clock signal in the range of 100 kHz to 50 MHz with rise and fall times of less than 3ns. The trace carrying the clock signal should be as short as possible and should not cross any other signal line, analog or digital, not even at 90. If the CLK is interrupted, or its frequency too low, the charge on internal capacitors can dissipate to the point where the accuracy of the output data will degrade. This is what limits the lowest sample rate to 100 ksps. The duty cycle of the clock signal can affect the performance of the A/D Converter. Because achieving a precise duty cycle is difficult, the ADC12040 is designed to maintain performance over a range of duty cycles. While it is specified and performance is guaranteed with a 50% clock duty cycle, performance is typically maintained over a clock duty cycle range of 45% to 55%. The clock line should be terminated at its source in the characteristic impedance of that line. It is highly desirable that the the source driving the ADC CLK input only drive that pin. However, if that source is used to drive other things, each driven pin should be a.c. terminated with a series RC to ground, as shown in Figure 4, such that the resistor value is equal to the characteristic impedance of the clock line and the capacitor value is 1.3.1 Single-Ended Operation Single-ended performance is lower than with differential input signals. For this reason, single-ended operation is not recommended. However, if single-ended operation is required, and the resulting performance degradation is acceptable, one of the analog inputs should be connected to the d.c. common mode voltage of the driven input. The peak-to-peak differential input signal should be twice the reference voltage to maximize SNR and SINAD performance (Figure 2b). For example, set VREF to 1.0V and bias VIN- to 1.0V and drive VIN+ with a signal range of 0V to 2.0V. Because very large input signal swings can degrade distortion performance, better performance with a single-ended input can be obtained by reducing the reference voltage while maintaining a full-range output. and indicate the input to output relationship of the ADC12040. 1.3.2 Driving the Analog Inputs The VIN+ and the VIN- inputs of the ADC12040 consist of an analog switch followed by a switched-capacitor amplifier. The capacitance seen at the analog input pins changes with the clock level, appearing as 8 pF when the clock is low, and 7 pF when the clock is high. Although this difference is small, a dynamic capacitance is more difficult to drive than is a fixed capacitance, so choose the driving amplifier carefully. The LMH6550, the LMH6702 and the LMH6628 are a good amplifiers for driving the ADC12040. The internal switching action at the analog inputs causes energy to be output from the input pins. As the driving source tries to compensate for this, it adds noise to the signal. To prevent this, use an RC at each of the inputs, as shown in Figure 5 and Figure 6. These components should be placed close to the ADC because the input pins of the ADC is the most sensitive part of the system and this is the last opportunity to filter the input. The capacitors are for Nyquist applications and should be eliminated for undersampling applications. The LMH6550 and the LMH6552 are excellent devices for driving the ADC12040, especially when single-ended to differential conversion with d.c. coupling is necessary. An example of the use of the LMH6550 to drive the analog input of the ADC12040 is shown in Figure 5. For high frequency, narrow band applications, a transformer is generally the recommended way to drive the analog inputs, as shown in Figure 6. where tPD is the signal propagation rate down the clock line, "L" is the line length and ZO is the characteristic impedance of the clock line. This termination should be as close as possible to the ADC clock pin but beyond it as seen from the clock source. Typical tPD is about 150 ps/inch (60 ps/cm) on FR-4 board material. The units of "L" and tPD should be the same (inches or centimeters). Take care to maintain a constant clock line impedance throughout the length of the line. Refer to Application Note AN-905 or AN-1113 for information on setting and determining characteristic impedance 2.2 The OE Input The OE input, when high, puts the output pins into a high impedance state. When this pin is low the outputs are in the active state. The ADC12040 will continue to convert whether this input is high or low, but the output can not be read while the OE pin is high. The OE input should NOT be used to multiplex devices together to drive a common bus as this will result in excessive capacitance on the data output pins, reducing SNR and SINAD performance of the converter. See Section 3.0. 1.3.3 Input Common Mode Voltage The input common mode voltage, VCM, should be in the range indicated in Section 1.0 and be of a value such that the peak excursions of the analog input signal do not go more negative than ground or more positive than the VA supply voltage. The nominal VCM should generally be equal to VREF/2, but VRM can be used as a VCM source as long as VRM need not supply more than 10 A of current. Figure 5 shows the use of the VRM output to drive the VCM input of the LMH6550. The common mode www.national.com 2.3 The PD Input The PD input, when high, holds the ADC12040 in a powerdown mode to conserve power when the converter is not being used. The power consumption in this state is 70 mW with a 40MHz clock and 40mW if the clock is stopped. The 14 conversion, the more instantaneous digital current flows through VDR and DR GND. These large charging current spikes can cause on-chip noise that can couple into the analog circuitry, degrading dynamic performance. Adequate power supply bypassing and careful attention to the ground plane will reduce this problem. Additionally, bus capacitance beyond that specified will cause tOD to increase, making it difficult to properly latch the ADC output data. The result could be an apparent reduction in dynamic performance. To minimize noise due to output switching, minimize the load currents at the digital outputs. This can be done by connecting buffers (74AC541, for example) between the ADC outputs and any other circuitry. Only one driven input should be connected to each output pin. Additionally, inserting series 100 resistors at the digital outputs, close to the ADC pins, will isolate the outputs from trace and other circuit capacitances and limit the output currents, which could otherwise result in performance degradation. See Figure 4. While the ADC12040 will operate with VDR voltages down to 1.8V, tOD increases with reduced VDR. Be careful of external timing when using reduced VDR. 3.0 DATA OUTPUTS The ADC12040 has 12 TTL/CMOS compatible Data Output pins. Valid offset binary data is present at these outputs while the OE and PD pins are low. While the tOD time provides information about output timing, a simple way to capture a valid output is to latch the data on the edge of the conversion clock (pin 10). Which edge to use will depend upon the clock frequency and duty cycle. If the rising edge is used, the tOD time can be used to determine maximum hold time acceptable of the driven device data inputs. If the falling edge of the clock is used, care must be taken to be sure that adequate setup and hold times are allowed for capturing the ADC output data. Be very careful when driving a high capacitance bus. The more capacitance the output drivers must charge for each 20014813 FIGURE 4. Simple Application Circuit with Single-Ended to Differential Buffer 15 www.national.com ADC12040 output data pins are undefined in this mode. The data in the pipeline is corrupted while in the power down mode. The Power Down Mode Exit Cycle time is determined by the value of the capacitors on pins 30, 31 and 32. These capacitors loose their charge in the Power Down mode and must be charged by on-chip circuitry before conversions can be accurate. ADC12040 20014814 FIGURE 5. Differential Drive Circuit of Figure 4 20014815 FIGURE 6. Driving the Signal Inputs with a Transformer The VDR pin provides power for the output drivers and may be operated from a supply in the range of 2.35V to VD (nominal 5V). This can simplify interfacing to 3V devices and systems. DO NOT operate the VDR pin at a voltage higher than VD. 4.0 POWER SUPPLY CONSIDERATIONS The power supply pins should be bypassed with a 10 F capacitor and with a 0.1 F ceramic chip capacitor within a centimeter of each power pin. Leadless chip capacitors are preferred because they have low series inductance. As is the case with all high-speed converters, the ADC12040 is sensitive to power supply noise. Accordingly, the noise on the analog supply pin should be kept below 150 mVP-P. No pin should ever have a voltage on it that is in excess of the supply voltages, not even on a transient basis. Be especially careful of this during turn on and turn off of power. www.national.com 5.0 LAYOUT AND GROUNDING Proper grounding and proper routing of all signals are essential to ensure accurate conversion. Maintaining separate analog and digital areas of the board, with the ADC12040 between these areas, is required to achieve specified performance. The ground return for the data outputs (DR GND) carries the ground current for the output drivers. The output current can 16 employs non-saturating transistor designs, or has low noise characteristics, such as the 74LS, 74HC(T) and 74AC(T)Q families. The worst noise generators are logic families that draw the largest supply current transients during clock or signal edges, like the 74F and the 74AC(T) families. In high speed circuits, however, it is often necessary to use these higher speed devices. Best performance requires careful attention to PC board layout and to proper signal integrity techniques. The effects of the noise generated from the ADC output switching can be minimized through the use of 47 to 100 resistors in series with each data output line. Locate these resistors as close to the ADC output pins as possible. 20014816 FIGURE 7. Example of a Suitable Layout Since digital switching transients are composed largely of high frequency components, total ground plane copper weight will have little effect upon the logic-generated noise. This is because of the skin effect. Total surface area is more important than is total ground plane volume. Generally, analog and digital lines should cross each other at 90 to avoid crosstalk. To maximize accuracy in high speed, high resolution systems, however, avoid crossing analog and digital lines altogether. It is important to keep clock lines as short as possible and isolated from ALL other lines, including other digital lines. Even the generally accepted 90 crossing should be avoided with the clock line as even a little coupling can cause problems at high frequencies. This is because other lines can introduce jitter into the clock line, which can lead to degradation of SNR. Also, the high speed clock can introduce noise into the analog chain. Best performance at high frequencies and at high resolution is obtained with a straight signal path. That is, the signal path through all components should form a straight line wherever possible. Be especially careful with the layout of inductors. Mutual inductance can change the characteristics of the circuit in which they are used. Inductors should not be placed side by side, even with just a small part of their bodies beside each other. The analog input should be isolated from noisy signal traces to avoid coupling of spurious signals into the input. Any ex- ternal component (e.g., a filter capacitor) connected between the converter's input pins and ground or to the reference input pin and ground should be connected to a very clean point in the ground plane. Figure 7 gives an example of a suitable layout. A single ground plane is recommended with separate analog and digital power planes. The analog and digital power planes should NOT overlap each other. All analog circuitry (input amplifiers, filters, reference components, etc.) should be placed over the analog power plane. All digital circuitry and I/O lines should be placed over the digital power plane. Furthermore, all components in the reference circuitry and the input signal chain that are connected to ground should be connected together with short traces and enter the ground plane at a single point. All ground connections should have a low inductance path to ground. 6.0 DYNAMIC PERFORMANCE To achieve the best dynamic performance, the clock source driving the CLK input must be free of jitter. Isolate the ADC clock from any digital circuitry with buffers, as with the clock tree shown in Figure 8. As mentioned in Section 5.0, it is good practice to keep the ADC clock line as short as possible and to keep it well away from any other signals. Other signals can introduce jitter into the clock signal, which can lead to reduced SNR performance, and the clock can introduce noise into other lines. 17 www.national.com ADC12040 exhibit high transients that could add noise to the conversion process. To prevent this from happening, the DR GND pins should NOT be connected to system ground in close proximity to any of the ADC12040's other ground pins. Capacitive coupling between the typically noisy digital circuitry and the sensitive analog circuitry can lead to poor performance. The solution is to keep the analog circuitry separated from the digital circuitry, and to keep the clock line as short as possible. Digital circuits create substantial supply and ground current transients. The logic noise thus generated could have significant impact upon system noise performance. The best logic family to use in systems with A/D converters is one which ADC12040 Even lines with 90 crossings have capacitive coupling, so try to avoid even these 90 crossings of the clock line. rate analog and digital areas on the pc board will reduce this problem. Additionally, bus capacitance beyond that specified will cause tOD to increase, making it difficult to properly latch the ADC output data. The result could, again, be an apparent reduction in dynamic performance. The digital data outputs should be buffered (with 74AC541, for example). Dynamic performance can also be improved by adding series resistors at each digital output, close to the ADC12040, which reduces the energy coupled back into the converter output pins by limiting the output current. A reasonable value for these resistors is 100. Using an inadequate amplifier to drive the analog input. As explained in Section 1.3, the capacitance seen at the input alternates between 8 pF and 7 pF, depending upon the phase of the clock. This dynamic load is more difficult to drive than is a fixed capacitance. If the amplifier exhibits overshoot, ringing, or any evidence of instability, even at a very low level, it will degrade performance. A small series resistor and shunt capacitor at each amplifier output (as shown in Figure 5 and Figure 6) will improve performance. The LMH6550 , the LMH6702 and the LMH6628 have been successfully used to drive the analog inputs of the ADC12040. Also, it is important that the signals at the two inputs have exactly the same amplitude and be exactly 180 out of phase with each other. Board layout, especially equality of the length of the two traces to the input pins, will affect the effective phase between these two signals. Remember that an operational amplifier operated in the non-inverting configuration will exhibit more time delay than will the same device operating in the inverting configuration. Operating with the reference pins outside of the specified range. As mentioned in Section 1.2, VREF should be in the range of 20014817 FIGURE 8. Isolating the ADC Clock from other Circuitry with a Clock Tree 7.0 COMMON APPLICATION PITFALLS Driving the inputs (analog or digital) beyond the power supply rails. For proper operation, all inputs should not go more than 300 mV beyond the supply rails (more than 300 mV below the ground pins or 300 mV above the supply pins). Exceeding these limits on even a transient basis may cause faulty or erratic operation. It is not uncommon for high speed digital components (e.g., 74F and 74AC devices) to exhibit overshoot or undershoot that goes above the power supply or below ground when their output lines are not properly terminated. A resistor of about 33 to 47 in series with any offending digital input, close to the signal source, should eliminate the problem. Do not allow input voltages to exceed the supply voltage, even on a transient basis. Not even during power up or power down. Be careful not to overdrive the inputs of the ADC12040 with a device that is powered from supplies outside the range of the ADC12040 supply. Such practice may lead to conversion inaccuracies and even to device damage. Attempting to drive a high capacitance digital data bus. The more capacitance the output drivers must charge for each conversion, the more instantaneous digital current flows through VDR and DR GND. These large charging current spikes can couple into the analog circuitry, degrading dynamic performance. Adequate bypassing and maintaining sepa- www.national.com 1.0V VREF 2.2V Operating outside of these limits could lead to performance degradation. Using a clock source with excessive jitter, using excessively long clock signal trace, or having other signals coupled to the clock signal trace. This will cause the sampling interval to vary, causing excessive output noise and a reduction in SNR and SINAD performance. 18 ADC12040 Physical Dimensions inches (millimeters) unless otherwise noted 32-Lead LQFP Package Ordering Number ADC12040CIVY NS Package Number VBE32A 19 www.national.com ADC12040 12-Bit, 40 MSPS, 340mW A/D Converter with Internal Sample-and-Hold Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH www.national.com/webench Audio www.national.com/audio Analog University www.national.com/AU Clock Conditioners www.national.com/timing App Notes www.national.com/appnotes Data Converters www.national.com/adc Distributors www.national.com/contacts Displays www.national.com/displays Green Compliance www.national.com/quality/green Ethernet www.national.com/ethernet Packaging www.national.com/packaging Interface www.national.com/interface Quality and Reliability www.national.com/quality LVDS www.national.com/lvds Reference Designs www.national.com/refdesigns Power Management www.national.com/power Feedback www.national.com/feedback Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www.national.com/led PowerWise www.national.com/powerwise Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors Wireless (PLL/VCO) www.national.com/wireless THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2008 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated