Place and Play Bluetooth® Module
New PAN1322 Series
Panasonic New Product Introduction
All-In-One, Place and Play Bluetooth Module
Introducing Panasonic’s next generation, smartphone compatible, place and play Bluetooth module, the PAN1322 Series.
This module features an embedded microcontroller, Bluetooth 2.1 + EDR stack, serial port profile (SPP), AT command set API
and antenna. This cost engineered solution is based on a single chip solution that integrates an ARM7TDMI processor with
a Bluetooth controller. The BT 2.1 + EDR stack provides secure, reliable, high speed data connections using Secure Simple
Paring (SSP) eliminating manual password creation. Embedded serial port profile (SPP) frees application resources while the
AT command set API creates a simple firmware interface using modem commands. An onboard antenna does away with
2.4GHz RF circuit complexity.
Created with the design engineer in mind, product design cycles are greatly reduced using Panasonic’s reference design and
design review services. PCB layouts are simplified using available Gerber files and minimized with Panasonic’s tiny footprint
technology. The module is and is just 15.6mm x 8.7mm x 2.8mm and fully shielded to improve immunity. GPIO is exposed
using AT commands. All Panasonic Bluetooth RF modules carry FCC, IC, CE Bluetooth certifications.
The PAN1322 Series recognizes Apple’s authentication coprocessor and supports Bluetooth Serial Port Profile (SPP) data
communication1 with Apple’s iPhone and iPad®*. Connectivity also includes Android, smart phones and all Bluetooth enabled
devices2.
Panasonic remains committed to customers as a module manufacturer by extending product life using legacy footprints and
firmware interfaces to make the PAN1322 Series fully compatible with the module it replaces, the PAN1321 Series.
Hardware and firmware prototyping and testing are accelerated using the EVAL_PAN1322 development kit and SPP Toolbox
development environment.
• Bluetooth Version 2.1 + EDR
• SPP Device A and B, RFCOMM Proles
• Industrial Temperature Range, -40 to +85°C
• No External Components Needed
• Onboard Voltage Regulator, VIN=2.7 to 3.6 V
• Integrated ARM7RDMI 32-Bit Processor w/Patchable EEPROM
• 3.25 MBaud UART
• GPIO w/Interrupt and Wake-Up Capabilities
• iOS and Android Devices
• Wireless Sensors
• Cable Replacement
• Industrial
• Medical
• Automotive
Website: www.panasonic.com/industrial
industrial@us.panasonic.com
1-800-344-2112
Copyright © 2013 Panasonic Corporation of North America.
All Rights Reserved. Specifications are subject to change without notice.
PAN1322 Series NPI, FY13-046-XXX
Features Applications
RoHS
COMPLIANT
*Apple iPad and iPhone are trademarks of Apple Inc
1. Apple authentication coprocessor and MFI certification is required.
2. Connectivity requires that devices support Bluetooth Serial Port Profile
EEPROM
I2C
Ceramic
Antenna
Filter /
Matching
Balun
PMB8754
BlueMoon
UniCellular
Crystal
26 MHz
Voltage
Regulator
VDD1
VDD_UART
UART
GPIO
VSUPPLY
Block Diagram (PAN1322-SPP)
Parameter Value Condition
Receiver Sensitivity -86 dBm typ. Ideal Signal
Output Power +3 dBm typ. @ 50 Ohm Antenna Pin
Power Supply 2.7 to 3.5 V Single Voltage Operation
Ultra Low Power Mode 80 µA T = 2.5°C
ACL (Transmit 3-DH1) 40 mA Enhanced Data Rate, 531.2kb/s
ACL (Receive 3-DH1) 37 mA Enhanced Data Rate, 531.2kb/s
Operating Temperature -40 to +85°C
Technical Characteristics
Part Number Description
ENW-89841A3KF PAN1322 Bluetooth Module, SPP, Integrated Antenna
EVAL_PAN1322 PAN1322 Evaluation Kit
Ordering Information
Website: www.panasonic.com/industrial
industrial@us.panasonic.com
1-800-344-2112
Copyright © 2013 Panasonic Corporation of North America.
All Rights Reserved. Specifications are subject to change without notice.
PAN1322 Series NPI, FY13-046-XXX
For detailed specification information on the PAN1322 Place and Play Bluetooth Module, visit our website at:
http://www.panasonic.com/rfmodules/
Additional Information
