3MTM Safety-WalkTM Slip-Resistant Materials Technical Data Sheet Revision J, December 2016 Product Descriptions 3MTM Safety-WalkTM Coarse Tapes and Treads - 700 Series The product consists of large abrasive particles bonded by a tough, durable polymer to a dimensionally stable plastic film. The reverse side is coated with a pressure-sensitive adhesive covered by a removable protective liner. Standard Sizes: Refer to Standard Product Chart (Page 2) * Colors: Black #710, Gray #770 * Custom sizes: Available upon request 3MTM Safety-WalkTM Slip-Resistant General Purpose Tapes and Treads - 600 Series The product consists of abrasive particles bonded by a tough, durable polymer to a dimensionally stable plastic film. The reverse side is coated with a pressure-sensitive adhesive covered by a removable protective liner. Standard Sizes: Refer to Standard Product Chart (Page 2) * Colors: Black #610, Clear #620, Safety Yellow #630, Safety Yellow/Black Stripe #613, and Black with Photo-luminescent (PL) strip #690 * Custom sizes: Available upon request 3MTM Safety-WalkTM Slip-Resistant Conformable Tapes and Treads - 500 Series The product consists of abrasive particles bonded by a tough, durable polymer to aluminum foil. The reverse side is coated with a pressure-sensitive adhesive covered by a removable protective liner. The product is designed to stretch and conform to irregular surfaces such as diamond plating or flat surfaces with rivets or screw heads, ladder rungs, etc. Standard Sizes: Refer to Standard Product Chart (Page 2) * Colors: Black #510 and Safety Yellow #530 * Custom sizes: Available upon request 3MTM Safety-WalkTM Slip-Resistant Medium Resilient Tapes and Treads - 300 Series The product consists of dimensionally stable plastic film coated with a textured resilient surface. The reverse side is coated with a pressure-sensitive adhesive covered by a removable protective liner. Standard Sizes: Refer to Standard Product Chart (Page 2) * Colors: Black #310 and Gray #370 * Custom sizes and colors: Available upon request. 3MTM Safety-WalkTM Slip-Resistant Fine Resilient Tapes and Treads - 200 Series Quick Links Resource Library Safety Data Sheets (SDS) Video Library Some of these links lead to web-based resources that are not product-specific. The product consists of a fine textured resilient top surface. The reverse side is coated with a pressure-sensitive adhesive covered by a removable protective liner. Standard Sizes: Refer to Standard Product Chart (Page 2) * Colors: White #280 and Clear #220 * Custom sizes: Available upon request Accessories 3MTM Safety-WalkTM Primer Primer is a solvent-based adhesive. It is to be applied to rough or porous surfaces before application of adhesive-backed products. One quart covers approximately 35 square feet. Size: 1 quart can 3MTM Safety-WalkTM Edge Sealing Compound Edge Sealing Compound is a liquid, solvent-based sealer in a convenient tube applicator. The product seals the exposed edges of Safety-Walk slip-resistant materials, providing extra protection from excessive moisture or liquids. One five-ounce tube seals approximately 75 to 100 linear feet. Size: 5 oz. tube 3MTM Safety-WalkTM Rubber Hand Roller Rubber Hand Roller helps provide a firm bond when Safety-Walk slip-resistant materials are applied. Size: Roller - 1 and 3/8 " diameter x 2" wide Overall length - 6" 3MTM Safety-WalkTM Slip-Resistant Materials Standard Product Chart 3MTM Safety-WalkTM Slip-Resistant Tapes and Treads Standard Sizes and Colors Coarse 700 Series General Purpose 600 Series Size Black #710 Gray #770 Black #610 3/4" x 24" x 5 1/2" x 5 1/2" x 6" x 24" x Safety Yellow #630 Clear #620 x Conformable 500 Series Safety Yellow /Black Stripe #613 Medium Resilient 300 Series Black PL Strip #690 Black #510 x x x x x x x x Safety Yellow #530 Black #310 Fine Resilient 200 Series Gray #370 White #280 Clear #220 x x x x x x x x x 2" x 30' x 3" x 30' 4" x 30' x 6" x 30' x 24" x 30' x x x x 3/4" x 60' x 1" x 60' x x x 2" x 60' x x x x x 3" x 60' 4" x 60' x x x x x x x 6" x 60' x x x x x x x x x 12" x 60' x x x x x x 18" x 60' x x x x 24" x 60' x 36" x 60' x 48" x 60' x x x x x x x x x x Custom sizes available upon request for all materials. Customs colors available upon request for Medium Resilient materials. 2 Technical Data Sheet - Revision J, December 2016 3MTM Safety-WalkTM Slip-Resistant Materials Product Selection Guide Type of 3MTM Safety-WalkTM Slip-Resistant Tapes and Treads Coarse 700 Series General Purpose 600 Series Conformable 500 Series Farm Machinery x x 0 Construction Equipment Forklifts Cherry pickers x x 0 x 0 Applications Steps, stairs, and platforms Recreational Vehicles Snowmobiles ATVs Garden tractors Lawn mowers x x 0 Wet and oily areas x x 0 Loading docks Cold storage Catwalks Platform/ramps x x 0 x 0 x 0 Ladders Step stools Scaffolds Airplane decks/cargo holds Trains Semi-trailers Buses Ships decks x Medium Resilient 300 Series Water skis Surf boards Jet skis Boats x Swimming pools Pool accessories Diving boards x Bath area Showers x x x Bathtubs Conveyors Pulleys x x Food service area* Machine shops Auto repair shops Garages Fine Resilient 200 Series x x X - Recommended for flat or smooth surfaces 0 - Recommended around corners or for irregular surfaces * - Not recommended for application on greasy quarry tiles Technical Data Sheet - Revision J, December 2016 3 3MTM Safety-WalkTM Slip-Resistant Materials Typical Properties Type of 3MTM Safety-WalkTM Slip-Resistant Tapes and Treads Product Attribute Coarse 700 Series General Purpose 600 Series Conformable 500 Series Medium Resilient 300 Series Fine Resilient 200 Series Black #710 Gray #770 Black #610 Safety Yellow #630 Clear #620 Safety Yellow/Black Stripe #613 Black PL Strip #690 Black #510 Safety Yellow #530 Black #310 Gray #370 Clear #220 White #280 5.50 1,700 2.4 730 2.4 730 2.4 730 2.4 730 2.8 850 2.7 830 2.1 640 40 F (4 C) 40 F (4 C) 40 F (4 C) 40 F (4 C) 40 F (4 C) 40 F (4 C) 40 F (4 C) 50 F (10 C) 3M-SW-29.0 Maximum Service Temperature 175 F (79 C) 175 F (79 C) 150 F (66 C) 150 F (66 C) 150 F (66 C) 175 F (79 C) 175 F (79 C) 150 F (66 C) ASTM E648-10e1 or (NFPA253) Flammability Average Critical: -Radiant Flux W/cm2 -NFPA Classification 1.02 Class I 1.01 Class I 1.01 Class I 1.01 Class I 1.02 Class I 0.37 Class II 1.01 Class I --- U.S Coast Guard Approval Number: 164.117/ 50/0 --- --- --- --- --- --- Pass Pass Pass Pass Pass Pass --- --- Pass Pass Pass Pass Pass Pass Pass --- 73 174 98 97 630: 47 47 620: 60 40 53 47 90 32 57 65 78 244 177 164 Color Applied Weight (oz.)/ ft2 (g)/m2 Minimum Application Temperature 2010 IMO FTP Code, Annex 1 Parts 2 and 5 FAA 25.855-F-1 T3003 Aluminum Substrate (Baggage) FAA 25-853-F-1 T3003 Aluminum Substrate (Interior surface) ASTM E662-09 or (NFPA258) - Smoke Density (Dm corrected) -Flaming -Non-Flaming 630: 1.02 Class I 620: 0.99 Class 1 Dynamic Coefficient of Friction Sensor Condition Coarse 700 Series General Purpose Black #610 General Purpose #630, #620 General Purpose #613, #690 Conformable 500 Series Medium Resilient 300 Series Fine Resilient 200 Series Rubber Dry Water Oil 1.05 1.00 0.76 1.04 1.02 0.87 1.02 1.05 0.90 1.02 1.05 0.90 1.04 0.94 0.95 1.06 0.83 0.31 1.29 0.86 0.35 Leather Dry Water Oil 0.65 0.83 N/A 0.74 1.19 N/A 0.78 1.14 N/A N/A N/A N/A 0.72 1.14 N/A 0.73 0.77 N/A 0.66 0.79 N/A Static Coefficient of Friction 4 Sensor Condition Coarse 700 Series General Purpose Black #610 General Purpose #630, #620 General Purpose #613, #690 Conformable 500 Series Medium Resilient 300 Series Fine Resilient 200 Series Rubber Dry Water Oil 1.24 1.14 1.05 1.40 1.30 1.17 1.30 1.25 1.31 1.30 1.25 1.31 1.38 1.25 1.28 1.06 0.84 0.51 1.38 0.81 0.58 Leather Dry Water Oil 0.90 1.05 N/A 1.00 1.64 N/A 1.05 1.48 N/A N/A N/A N/A 1.04 1.46 N/A 0.81 0.81 N/A 0.82 0.93 N/A Technical Data Sheet - Revision J, December 2016 3MTM Safety-WalkTM Slip-Resistant Materials Slip Resistance Coarse 700 Series General Purpose Black #610 General Purpose #630, #620 General Purpose #613, #690 Conformable 500 Series Medium Resilient 300 Series Fine Resilient 200 Series Friction (dry) R13 - - - - - - Volume (ml/dmsq) V8 - - - - - - DIN9Ger.51130 (ZH1/571): Value Chemical Resistance Use this guide to help select the proper 3MTM Safety-WalkTM Slip-Resistant Tapes and Treads when exposure to chemicals is anticipated. * Fine Resilient Clear may turn cloudy during continuous immersion in water. It will regain clarity after it dries. * Colors may be affected by extended exposure to some chemicals. Type of 3MTM Safety-WalkTM Slip-Resistant Material Chemical Coarse 700 Series General Purpose 600 Series Conformable 500 Series Medium Resilient 300 Series Fine Resilient 200 Series Color Black #710 Gray #770 Black #610 Safety Yellow #630 Clear #620 Safety Yellow/Black Stripe #613 Black PL Strip #690 Black #510 Safety Yellow #530 Black #310 Gray #370 Clear #220 White #280 Water R R R R R R R R Bleach R R I I R I R R 1% Hydrochloric Acid R R R R R R R R 1% Sodium Hydroxide I I NR I I NR R R Detergent (1% Dreft in Water) R R R NR NR R R R Soap (1% Ivory Flakes in Water) R R R I I R R R Isopropyl Alcohol R R R I I R R I Motor Oil R R R R R R R R NR NR R R R I R NR Peanut Oil R R R R R R R R Methyl Ethyl Ketone I I I I I I I NR Hydraulic Fluid (Skydrol 500B) Mineral Spirits R R NR I I NR NR NR NR NR IC NR NR NR NR NR 25% Sulfuric Acid Water R R I R R IC R R 50% Antifreeze in Water R R R I R R R R Windshield Washer Fluid R R R R R R R R Diesel Fuel R R I I I I NR NR Salt Water R R R R R R R R Gasoline (Unleaded) R - Recommended, generally not continuous immersion I - Recommended for intermittent exposure only IC - Can stand incidental contact, provided cleaning/rinsing is performed after exposure NR - Not recommended Technical Data Sheet - Revision J, December 2016 5 3MTM Safety-WalkTM Slip-Resistant Materials Surface Preparation Table Solvent Wipe1 Surface Bare metal/polyethylene/propylene x Painted metal or plastic/painted wood/gelcoated fiberglass/epoxy-coated floor3 x Strip Floor Finish; Degrease; Wash and Rinse2 Prime Coat Recommended No x No Rough or smooth porous concrete x Yes Painted or coated smooth concrete x No Vinyl tile/marble/terrazzo/ceramic x No x Yes Quarry Tile 4 1 - Use solvent suitable for removing grease and oil. Follow manufacturer's directions for proper handling. 2 - Use detergent, degreaser or stripping chemical as appropriate. 3 - Untreated and treated wood must be painted before application of any 3MTM Safety-WalkTM Slip-Resistant Materials. 4 - Not recommended for use in commercial kitchens. Directions for Use Surface Preparation Instructions 1. 2. 3. 4. 5. Make sure surface is clean, dry, smooth and above minimum application temperature when applying 3MTM Safety-WalkTM Slip-Resistant material. Repair or replace any broken or damaged surface. Minimum application temperatures: Coarse (700 series) 40F (4C) General Purpose (600 series) 40F (4C) Conformable (500 series) 40F (4C) Medium Resilient (300 series) 40F (4C) Fine Resilient (200 series) 50F (10C) Remove chipped, cracked or peeled paint prior to applying Safety-Walk material. Remove loose residue from surface. If present, floor finish may be removed prior to application. Referring to the "Surface Preparation Table" on page 6, use the appropriate cleaner or solvent wipe to clean the surface. After cleaning, allow surface to dry thoroughly. Priming Instructions 1. Prime clean, dry surfaces with 3MTM Safety-WalkTM Primer, especially: a. Uncoated concrete surfaces. b. Coated, painted or porous concrete if surface is excessively rough. c. Other porous surfaces. 2. Priming Instructions a. Properly clean the surface following the "Surface Preparation Table" on page 6. b. Use a paint brush to apply a thin coat of Safety-Walk primer where material is to be placed. c. Allow the primed area to dry thoroughly (no evidence of stickiness or tackiness) before applying Safety-Walk slip-resistant material. Approximate drying time is 15 minutes. Application Instructions Tools Needed: Rubber Hand Roller or Rubber Mallet 1. 2. 3. 6 Individual pieces should be spaced a minimum of 1/2" apart and a maximum of 2" apart. Round the corners of any pieces cut from rolls. Peel protective liner back about 2" from one end and position piece on surface. Technical Data Sheet - Revision J, December 2016 3MTM Safety-WalkTM Slip-Resistant Materials i IMPORTANT NOTE Minimize touching adhesive with fingers. 4. 5. Continue to remove liner. Press firmly in place as liner is removed. For small pieces: Peel liner off piece. Holding piece by its edges, curve it gently with the adhesive side out. Align the middle of the piece over the middle of the target surface and press down. Finally, press into firm contact with surface using a rubber hand roller by starting in middle and rolling out toward edges. For applying 3MTM Safety-WalkTM Conformable Tapes and Treads, use a soft-headed rubber mallet to ensure product conformability to surface. Pound edges extra hard. On steps, apply tread material 1/2" from stair edge to prevent edge curl and premature wear. 6. 7. 8. Maintenance Instructions * To maintain product effectiveness, the application should be inspected periodically. * To ensure that 3MTM Safety-WalkTM Slip-Resistant Materials are kept free of dirt and other residue that might impair functionality: - Coarse, General Purpose and Conformable tapes and treads should be deck brushed regularly. - Medium and Fine Resilient Treads should be mopped or deck brushed regularly. * Use an appropriate degreaser/cleaner for general maintenance to keep material and surrounding surfaces dirt and grease free. * To remove and replace worn or torn material: - Start by pulling up old material. Use of a heat gun may assist in this process. - After removal of old material, use 3MTM General Purpose Adhesive Remover (08987) or an equivalent product to soften adhesive residue and allow scraping of surface in preparation for product replacement. Important for Proper Application and Service Life 1. 2. 3. 4. All surfaces must be clean, dry and at recommended temperature before applying product. Rough or porous surfaces must be primed with 3MTM Safety-WalkTM Primer for proper adhesion. A 3MTM Safety-WalkTM Rubber Hand Roller should be used to assure a firm bond when applying all Safety-Walk slip-resistant materials. For extra protection from excessive moisture or liquids, use 3MTM Safety-WalkTM Edge Sealing Compound. Safety-Walk slip-resistant materials are not recommended for continuous immersion in water. 5. 3MTM Safety-WalkTM Slip-Resistant Material can be applied on most painted surfaces that are in good condition. The material will adhere as well as the base paint. Painted surfaces must be thoroughly dry before application of any 3MTM Safety-WalkTM Slip-Resistant Material. 6. Treated or untreated wood must be painted prior to application of 3MTM Safety-WalkTM Slip-Resistant Material. 7. Do not apply 3MTM Safety-WalkTM Slip-Resistant Material over surfaces with constant water contact or moisture seepage. 8. Do not apply 3MTM Safety-WalkTM Slip-Resistant Material over grouting. Avoid cracks in concrete and cracks in any surface. 9. 3MTM Safety-WalkTM Slip-Resistant Materials are not recommended for quarry tile in commercial kitchens due to constant oil exposure. 10. Store product in its original carton, preferably at 40F (4C) to 100F (37.7C). Humidity range of 40% to 60%. 11. It is recommended to use the product within five years from the date product is received. i IMPORTANT NOTE 3MTM Safety-WalkTM Slip Resistant Tapes and Treads Series 200, 300, 500, 600, and 700 have been certified by the National Floor Safety Institute (NFSI) as providing "high traction". A wet static coefficient of friction (SCOF) of greater than 0.60 was chosen by NFSI as the criteria for "high traction" because according to NFSI, floor surfaces maintaining this level of slip resistance when wet have proven to reduce slip-and-fall claims by between 50% and 90%. Technical Data Sheet - Revision J, December 2016 7 3MTM Safety-WalkTM Slip-Resistant Materials i IMPORTANT NOTE 3MTM Safety-WalkTM Slip-Resistant Conform able Tapes and Treads - 500 Series is not presently qualified to, nor on the qualified products list associated with, any active Military Specification. 3MTM Safety-WalkTM Slip-Resistant General Purpose Tapes and Treads - 600 Series met, and was on the qualified products list associated with, Military Specification MIL-D-17951 E, which was canceled upon the release of Military Specification MIL-PRF24667 C. The 600 Series is not presently qualified to, nor on the qualified products list associated with, any active Military Specification. 3MTM Safety-WalkTM Coarse Tapes and Treads - 700 Series meets, and is on the qualified products list associated with, Military Specification MIL-PRF-24667 C Type XI Comp PS. Certificate of compliance to this standard is only available via military orders or special product request (SPR). Product Use Many factors beyond 3M's control and uniquely within user's knowledge and control can affect the use and performance of a 3M product in a particular application. The user is solely responsible for evaluating the product and determining whether it is fit for user's particular purpose and adequately maintained. Warranty, Limited Remedy, and Disclaimer 3M warrants that each 3M product will be free from defects in material and manufacture for 90 days from the date of purchase from 3M's authorized distributor. 3M MAKES NO OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If a 3M product does not conform to this warranty, the sole and exclusive remedy is, at 3M's option, replacement of the 3M product or refund of the purchase price. Limitation of Liability: Except to the extent prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal or equitable theory asserted. Limitation of Liability Except where prohibited by law, 3M will not be liable for any loss or damage arising from its products, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted. Change Summary For the most current 3M Technical Information available to successfully use this product, please view this Data Sheet electronically and click on the blue underlined links to view the relevant documents. Release J DEC-2016: * Added Colors to 600 Series throughout document. 3M Commercial Solutions 3M Center, Building 220-12E-04 St. Paul, MN 55144 Phone 1-800-328-0033 Web 3M.com/Facility (c) 3M 2016. All rights reserved. 3M and Safety-Walk are trademarks of 3M. Used under license in Canada. All other trademarks are property of their respective owners.Please recycle. Revision J, December 2016