DS90UR124,DS90UR241 DS90UR241Q DS90UR124Q 5-43 MHz DC-Balanced 24-Bit FPD-Link II Serializer and Deserializer Chipset Literature Number: SNLS231M October 5, 2011 5-43 MHz DC-Balanced 24-Bit FPD-Link II Serializer and Deserializer Chipset General Description The DS90UR241/124 Chipset translates a 24-bit parallel bus into a fully transparent data/control FPD-Link II LVDS serial stream with embedded clock information. This chipset is ideally suited for driving graphical data to displays requiring 18bit color depth - RGB666 + HS, VS, DE + 3 additional general purpose data channels. This single serial stream simplifies transferring a 24-bit bus over PCB traces and cable by eliminating the skew problems between parallel data and clock paths. It saves system cost by narrowing data paths that in turn reduce PCB layers, cable width, and connector size and pins. The DS90UR241/124 incorporates FPD-Link II LVDS signaling on the high-speed I/O. FPD-Link II LVDS provides a low power and low noise environment for reliably transferring data over a serial transmission path. By optimizing the Serializer output edge rate for the operating frequency range EMI is further reduced. In addition, the device features pre-emphasis to boost signals over longer distances using lossy cables. Internal DC balanced encoding/decoding is used to support AC-Coupled interconnects. Using National Semiconductor's proprietary random lock, the Serializer's parallel data are randomized to the Deserializer without the need of REFCLK. Features Supports displays with 18-bit color depth 5MHz to 43MHz pixel clock Automotive grade product AEC-Q100 grade 2 qualified 24:1 interface compression Embedded clock with DC Balancing supports AC-coupled data transmission Capable to drive up to 10 meters shielded twisted-pair cable No reference clock required (deserializer) Meets ISO 10605 ESD - Greater than 8 kV HBM ESD structure Hot plug support EMI Reduction - Serializer accepts spread spectrum input; data randomization and shuffling on serial link; Deserializer provides Adjustable PTO (progressive turnon) LVCMOS outputs @Speed BIST (built-in self test) to validate LVDS transmission path Individual power-down controls for both Transmitter and Receiver Power supply range 3.3V 10% 48-pin TQFP package for Transmitter and 64-pin TQFP package for Receiver Temperature range -40C to +105C Backward compatible mode with DS90C241/DS90C124 Applications Automotive Central Information Display Automotive Instrument Cluster Display Automotive Heads-Up Display Remote Camera-based Driver Assistance Systems Applications Diagram 20194527 TRI-STATE(R) is a registered trademark of National Semiconductor Corporation. (c) 2011 National Semiconductor Corporation 201945 www.national.com DS90UR241Q/DS90UR124Q 5-43 MHz DC-Balanced 24-Bit FPD-Link II Serializer and Deserializer Chipset DS90UR241Q DS90UR124Q DS90UR241Q/DS90UR124Q Block Diagram 20194501 Ordering Information NSID Package Type DS90UR241QVS 48-Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch VBC48A DS90UR241QVSX 48-Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch VBC48A DS90UR241IVS 48-Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch VBC48A DS90UR241IVSX 48-Lead TQFP style, 7.0 X 7.0 X 1.0 mm, 0.5 mm pitch VBC48A DS90UR124QVS 64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch VEC64A DS90UR124QVSX 64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch VEC64A DS90UR124IVS 64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch VEC64A DS90UR124IVSX 64-Lead TQFP style, 10.0 X 10.0 X 1.0 mm, 0.5 mm pitch VEC64A www.national.com Package ID 2 Quantity 1000 1000 1000 1000 Supply Voltage (VDD) -0.3V to +4V LVCMOS Input Voltage -0.3V to (VDD +0.3V) LVCMOS Output Voltage -0.3V to (VDD +0.3V) LVDS Receiver Input Voltage -0.3V to +3.9V LVDS Driver Output Voltage -0.3V to +3.9V LVDS Output Short Circuit Duration 10 ms Junction Temperature +150C Storage Temperature -65C to +150C Lead Temperature (Soldering, 4 seconds) +260C Maximum Package Power Dissipation Capacity (Note 2) Package De-rating: 1/JA C/W above +25C 21.0C/W 42.8 (4L*); 67.2 (2L*)C/W JC 14.6C/W 10 kV Air Discharge (DOUT+, DOUT-) 30 kV Contact Discharge (RIN+, RIN-) 10 kV Air Discharge (RIN+, RIN-) 30 kV Supply Voltage (VDD) Operating Free Air Temperature (TA) Clock Rate Supply Noise 45.8 (4L*); 75.4 (2L*) C/W JA Contact Discharge (DOUT+, DOUT-) Recommended Operating Conditions DS90UR241 - 48L TQFP JC DS90UR124 - 64L TQFP RD = 2 k, CS = 330 pF Min 3.0 Nom 3.3 Max 3.6 Units V -40 5 +25 +105 43 100 C MHz mVP-P Electrical Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Pin/Freq. Min Typ Max Units Tx: DIN[0:23], TCLK, 2.0 TPWDNB, DEN, TRFB, GND RAOFF, VODSEL, RES0. Rx: RPWDNB, RRFB, -0.8 REN, PTOSEL, BISTEN, BISTM, SLEW, RES0. VDD V 0.8 V -1.5 V LVCMOS DC SPECIFICATIONS VIH High Level Input Voltage VIL Low Level Input Voltage VCL Input Clamp Voltage IIN Input Current ICL = -18 mA VIN = 0V or 3.6V VOH High Level Output Voltage IOH = -2 mA, SLEW = L IOH = -4 mA, SLEW = H VOL Low Level Output Voltage IOL = +2 mA, SLEW = L IOL = +4 mA, SLEW = H IOS Output Short Circuit Current VOUT = 0V IOZ TRI-STATE(R) Output Current RPWDNB, REN = 0V, VOUT = 0V or VDD Tx: DIN[0:23], TCLK, TPWDNB, DEN, TRFB, RAOFF, RES0. -10 Rx: RRFB, REN, PTOSEL, BISTEN, BISTM, SLEW, RES0. 2 +10 A Rx: RPWDNB -20 5 +20 A Rx: ROUT[0:23], RCLK, LOCK, PASS. 2.3 3.0 VDD V GND 0.33 0.5 V Rx: ROUT[0:23], RCLK, LOCK, PASS. 3 -40 -70 -110 mA -30 0.4 +30 A www.national.com DS90UR241Q/DS90UR124Q ESD Rating (ISO10605) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. JA 8 kV ESD Rating (HBM) Absolute Maximum Ratings (Note 1) DS90UR241Q/DS90UR124Q Symbol Parameter Conditions Pin/Freq. Min Typ Max Units +50 mV LVDS DC SPECIFICATIONS VTH Differential Threshold High Voltage VTL Differential Threshold Low Voltage IIN Input Current VOD Output Differential Voltage (DOUT+)-(DOUT-) VCM = +1.8V Rx: RIN+, RIN- -50 VIN = +2.4V, VDD = 3.6V VIN = 0V, VDD = 3.6V VOD VOS VOS IOS IOZ mV 100 250 A A 100 250 RL = 100, w/o preemphasis (Figure 10) VODSEL = L Tx: DOUT+, DOUT- 380 500 630 VODSEL = H 500 900 1100 Output Differential Voltage Unbalance RL = 100, w/o pre-emphasis VODSEL = L 1 50 mV Offset Voltage RL = 100, w/o pre-emphasis VODSEL = L 1.50 V RL = 100, w/o pre-emphasis VODSEL = L 50 mV DOUT = 0V, DIN = H, TPWDNB = 2.4V VODSEL = L -2.0 -5.0 -8.0 VODSEL = H -4.5 -7.9 -14.0 Offset Voltage Unbalance Output Short Circuit Current TRI-STATE Output Current VODSEL = H 1.00 1.25 VODSEL = H 3 VODSEL = H mV mA TPWDNB = 0V, DOUT = 0V OR VDD -15 1 +15 A TPWDNB = 2.4V, DEN = 0V DOUT = 0V OR VDD -15 1 +15 A TPWDNB = 2.4V, DEN = 2.4V, DOUT = 0V OR VDD NO LOCK (NO TCLK) -15 1 +15 A 60 85 mA 65 90 mA 66 90 mA 45 A SER/DES SUPPLY CURRENT (DVDD*, PVDD* AND AVDD* PINS) *DIGITAL, PLL, AND ANALOG VDDS IDDT Serializer Total Supply Current (includes load current) RL = 100, PRE = OFF, RAOFF = H, VODSEL = L RL = 100, PRE = 12 k, RAOFF = H, VODSEL = L RL = 100, PRE = OFF, RAOFF = H, VODSEL = H f = 43 MHz, CHECKER BOARD Pattern (Figure 1) f = 43 MHz, RANDOM pattern IDDTZ Serializer Supply Current Power-down TPWDNB = 0V (All other LVCMOS Inputs = 0V) IDDR Deserializer Total Supply Current (includes load current) CL = 4 pF, SLEW = H f = 43 MHz, CHECKER BOARD Pattern LVCMOS Output (Figure 2) 85 105 mA CL = 4 pF, SLEW = H f = 43 MHz, RANDOM pattern LVCMOS Output 80 100 mA 50 A IDDRZ Deserializer Supply Current Power-down www.national.com RPWDNB = 0V (All other LVCMOS Inputs = 0V, RIN+/RIN- = 0V) 4 Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions (Figure 5) Min Typ Max Units tTCP Transmit Clock Period tTCIH Transmit Clock High Time tTCIL Transmit Clock Low Time tCLKT TCLK Input Transition Time Figure 4, ((Note 9)) tJIT TCLK Input Jitter f = 43MHz (Note 10) 100 ps f = 33MHz 130 ps 23.25 T 200 ns 0.3T 0.5T 0.7T ns 0.3T 0.5T 0.7T ns 2.5 ns Serializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions tLHLT LVDS Low-to-High Transition Time RL = 100, VODSEL = L, LVDS High-to-Low Transition Time CL = 10 pF to GND, (Figure 3) tDIS DIN (0:23) Setup to TCLK tDIH DIN (0:23) Hold from TCLK tHZD DOUT HIGH to TRI-STATE Delay tLZD DOUT LOW to TRI-STATE Delay tZHD DOUT TRI-STATE to HIGH Delay tZLD DOUT TRI-STATE to LOW Delay tPLD Serializer PLL Lock Time RL = 100 tSD Serializer Delay RL = 100, PRE = OFF, RAOFF = L, TRFB = H, (Figure 8) RL = 100, PRE = OFF, RAOFF = L, TRFB = L, (Figure 8) tLLHT Min RL = 100, CL = 10 pF to GND, (Note 9), (Figure 5) TxOUT_E_O TxOUT_Eye_Opening. TxOUT_E_O centered on (tBIT/)2 Typ Max Units 245 550 ps 264 550 ps 4 ns 4 RL = 100, CL = 10 pF to GND, (Note 6), (Figure 6) ns 10 15 ns 10 15 ns 75 150 ns 75 150 ns 10 ms 3.5T+2 3.5T+10 ns 3.5T+2 3.5T+10 ns 5 MHz-43 MHz, RL = 100, CL = 10 pF to GND, RANDOM pattern (Note 10, Note 11), (Note 14) (Figure 9) 0.76 0.84 UI Deserializer Switching Characteristics Over recommended operating supply and temperature ranges unless otherwise specified. Symbol Parameter Conditions Pin/Freq. tRCP Receiver out Clock Period tRCP = tTCP, PTOSEL = H RCLK (Figure 15) tRDC RCLK Duty Cycle PTOSEL = H, SLEW = L tCLH LVCMOS Low-to-High Transition Time ROUT [0:23], RCLK, LOCK tCHL LVCMOS High-to-Low Transition Time CL = 4 pF (lumped load), SLEW = H (Note 9) tCLH LVCMOS Low-to-High Transition Time ROUT [0:23], RCLK, LOCK tCHL LVCMOS High-to-Low Transition Time CL = 4 pF (lumped load), SLEW = L (Note 9) 5 Min Typ Max Units 23.25 T 200 ns 45 50 55 % 1.5 2.5 ns 1.5 2.5 ns 2.0 3.5 ns 2.0 3.5 ns www.national.com DS90UR241Q/DS90UR124Q Serializer Input Timing Requirements for TCLK DS90UR241Q/DS90UR124Q Symbol tROS Parameter Conditions PTOSEL = L, SLEW = H, ROUT (0:7) Hold Data to RCLK (Figure 16) (Group 1) ROUT[0:7] tROS ROUT (8:15) Setup Data to RCLK (Group 2) ROUT [8:15], LOCK tROH ROUT (8:15) Hold Data to RCLK (Group 2) tROS ROUT (16:23) Setup Data to RCLK (Group 3) tROH ROUT (16:23) Setup Data to RCLK (Group 3) tROS ROUT (0:7) Setup Data to RCLK (Group 1) tROH ROUT (0:7) Setup Data to RCLK (Group 1) Pin/Freq. PTOSEL = L, SLEW = H, (Figure 16) ROUT [16:23] PTOSEL = H, SLEW = H, ROUT (0:7) Hold Data to RCLK (Figure 15) (Group 1) ROUT[0:7] tROS ROUT (8:15) Setup Data to RCLK (Group 2) ROUT [8:15], LOCK tROH ROUT (8:15) Hold Data to RCLK (Group 2) tROS ROUT (16:23) Setup Data to RCLK (Group 3) tROH ROUT (16:23) Setup Data to RCLK (Group 3) tHZR HIGH to TRI-STATE Delay tLZR LOW to TRI-STATE Delay tZHR TRI-STATE to HIGH Delay tZLR TRI-STATE to LOW Delay tDD Deserializer Delay PTOSEL = H, (Figure 12) RCLK tDSR Deserializer PLL Lock Time from Powerdown (Note 7, Note 9) RxIN_TOL-L Receiver INput TOLerance Left (Note 8, Note 9), (Note 11) (Figure 17) tROH RxIN_TOL-R Receiver INput TOLerance Right ROUT [16:23] PTOSEL = H, (Figure 14) Min Typ (0.35)* tRCP (0.5*tRCP)-3 UI ns (0.35)* tRCP (0.5*tRCP)-3 UI ns (0.35)* tRCP (0.5*tRCP)-3 UI ns (0.35)* tRCP (0.5*tRCP)-3 UI ns (0.35)* tRCP (0.5*tRCP)-3 UI ns (0.35)* tRCP (0.5*tRCP)-3 UI ns (0.35)* tRCP (0.5*tRCP)-2 UI ns (0.35)* tRCP (0.5*tRCP)+2 UI ns (0.35)* tRCP (0.5*tRCP)-1 UI ns (0.35)* tRCP (0.5*tRCP)+1 UI ns (0.35)* tRCP (0.5*tRCP)+1 UI ns (0.35)* tRCP (0.5*tRCP)-1 UI ns ROUT [0:23], RCLK, LOCK Max Units 3 10 ns 3 10 ns 3 10 ns 3 10 ns [5+(5/56)]T+3.7 [5+(5/56)]T +8 ns 5 MHz 128k*T ms 43 MHz 128k*T ms 0.25 UI 0.25 UI 5 MHz-43 MHz (Note 8),(Note 9, 5 MHz-43 MHz Note 11) (Figure 17) Note 1: "Absolute Maximum Ratings" indicate limits beyond which damage to the device may occur, including inoperability and degradation of device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions. Note 2: 4L =4 layer PCB per JEDEC specification, 2L = 2 layer PCB per JEDEC specification. Note 3: The Electrical Characteristics tables list guaranteed specifications under the listed Recommended Operating Conditions except as otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and are not guaranteed. Note 4: Typical values represent most likely parametric norms at VDD = 3.3V, Ta = +25 degC, and at the Recommended Operation Conditions at the time of product characterization and are not guaranteed. Note 5: Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, VOD, VTH and VTL which are differential voltages. Note 6: When the Serializer output is at TRI-STATE the Deserializer will lose PLL lock. Resynchronization MUST occur before data transfer. Note 7: tDSR is the time required by the Deserializer to obtain lock when exiting powerdown mode. Note 8: RxIN_TOL is a measure of how much phase noise (jitter) the Deserializer can tolerate in the incoming data stream before bit errors occur. It is a measurement in reference with the ideal bit position, please see National's AN-1217 for detail. Note 9: Specification is guaranteed by characterization and is not tested in production. Note 10: tJIT (@BER of 10e-9) specifies the allowable jitter on TCLK. tJIT not included in TxOUT_E_O parameter. www.national.com 6 DS90UR241Q/DS90UR124Q Note 11: UI - Unit Interval, equivalent to one ideal serialized data bit width. The UI scales with frequency. Note 12: Figures 1, 2 Figures 8, 12, 14show a falling edge data strobe (TCLK IN/RCLK OUT). Note 13: Figures 5, 15, 16 show a rising edge data strobe (TCLK IN/RCLK OUT). Note 14: TxOUT_E_O is affected by pre-emphasis value. AC Timing Diagrams and Test Circuits 20194502 FIGURE 1. Serializer Input Checkerboard Pattern 20194503 FIGURE 2. Deserializer Output Checkerboard Pattern 20194504 FIGURE 3. Serializer LVDS Output Load and Transition Times 7 www.national.com DS90UR241Q/DS90UR124Q 20194506 FIGURE 4. Serializer Input Clock Transition Times 20194507 FIGURE 5. Serializer Setup/Hold Times 20194508 FIGURE 6. Serializer TRI-STATE Test Circuit and Delay www.national.com 8 DS90UR241Q/DS90UR124Q 20194509 FIGURE 7. Serializer PLL Lock Time, and TPWDNB TRI-STATE Delays 20194510 FIGURE 8. Serializer Delay 20194515 FIGURE 9. Transmitter Output Eye Opening (TxOUT_E_O) 9 www.national.com DS90UR241Q/DS90UR124Q 20194517 VOD = (DOUT+) - (DOUT-) Differential output signal is shown as (DOUT+) - (DOUT-), device in Data Transfer mode. FIGURE 10. Serializer VOD Diagram 20194505 FIGURE 11. Deserializer LVCMOS Output Load and Transition Times 20194511 FIGURE 12. Deserializer Delay www.national.com 10 DS90UR241Q/DS90UR124Q 20194513 FIGURE 13. Deserializer TRI-STATE Test Circuit and Timing 20194514 FIGURE 14. Deserializer PLL Lock Times and RPWDNB TRI-STATE Delay 11 www.national.com DS90UR241Q/DS90UR124Q 20194512 FIGURE 15. Deserializer Setup and Hold Times and PTO, PTOSEL = H 20194521 Group 1 will be latched internally by sequence of (early 2UI, late 1UI, early 1UI, late 2UI) Group 2 will be latched internally by sequence of (late 1UI, early 1UI, late 2UI, early 2UI) Group 3 will be latched internally by sequence of (early 1UI, late 2UI, early 2UI, late 1UI) FIGURE 16. Deserializer Setup and Hold Times and PTO Spread, PTOSEL = L www.national.com 12 DS90UR241Q/DS90UR124Q 20194516 RxIN_TOL_L is the ideal noise margin on the left of the figure, with respect to ideal. RxIN_TOL_R is the ideal noise margin on the right of the figure, with respect to ideal. FIGURE 17. Receiver Input Tolerance (RxIN_TOL) and Sampling Window DS90UR241 Pin Diagram Serializer - DS90UR241 20194519 TOP VIEW DS90UR241 Serializer Pin Descriptions Pin # Pin Name I/O/PWR Description LVCMOS PARALLEL INTERFACE PINS 4-1, DIN[23:0] 48-44, 41-32, 29-25 LVCMOS_I Transmitter Parallel Interface Data Input Pins. Tie LOW if unused, do not float. 10 LVCMOS_I Transmitter Parallel Interface Clock Input Pin. Strobe edge set by TRFB configuration pin. TCLK 13 www.national.com DS90UR241Q/DS90UR124Q Pin # Pin Name I/O/PWR Description CONTROL AND CONFIGURATION PINS 9 TPWDNB LVCMOS_I Transmitter Power Down Bar TPWDNB = H; Transmitter is Enabled and ON TPWDNB = L; Transmitter is in power down mode (Sleep), LVDS Driver DOUT (+/-) Outputs are in TRI-STATE stand-by mode, PLL is shutdown to minimize power consumption. 24 VODSEL LVCMOS_I VOD Level Select VODSEL = L; LVDS Driver Output is 500 mV (RL = 100) VODSEL = H; LVDS Driver Output is 900 mV (RL = 100) For normal applications, set this pin LOW. For long cable applications where a larger VOD is required, set this pin HIGH. 18 DEN LVCMOS_I Transmitter Data Enable DEN = H; LVDS Driver Outputs are Enabled (ON). DEN = L; LVDS Driver Outputs are Disabled (OFF), Transmitter LVDS Driver DOUT (+/-) Outputs are in TRI-STATE, PLL still operational and locked to TCLK. 23 PRE LVCMOS_I Pre-emphasis Level Select PRE = NC (No Connect); Pre-emphasis is Disabled (OFF). Pre-emphasis is active when input is tied to VSS through external resistor RPRE. Resistor value determines pre-emphasis level. Recommended value RPRE 6 k; Imax = [48 / RPRE], RPREmin = 6 k 11 TRFB LVCMOS_I Transmitter Clock Edge Select Pin TRFB = H; Parallel Interface Data is strobed on the Rising Clock Edge. TRFB = L; Parallel Interface Data is strobed on the Falling Clock Edge 12 RAOFF LVCMOS_I Randomizer Control Input Pin RAOFF = H, Backwards compatible mode for use with DS90C124 Deserializer. RAOFF = L; Additional randomization ON (Default), Selects 2E7 LSFR setting. See Table 1 for more details. 5, 8, 13 RES0 LVCMOS_I Reserved. This pin MUST be tied LOW. LVDS SERIAL INTERFACE PINS 20 DOUT+ LVDS_O Transmitter LVDS True (+) Output. This output is intended to be loaded with a 100 load to the DOUT+ pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor. 19 DOUT- LVDS_O Transmitter LVDS Inverted (-) Output This output is intended to be loaded with a 100 load to the DOUT- pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor. POWER / GROUND PINS 22 VDD VDD Analog Voltage Supply, LVDS Output POWER 21 VSS GND Analog Ground, LVDS Output GROUND 16 VDD VDD Analog Voltage Supply, VCO POWER 17 VSS GND Analog Ground, VCO GROUND 14 VDD VDD Analog Voltage Supply, PLL POWER 15 VSS GND Analog Ground, PLL GROUND 30 VDD VDD Digital Voltage Supply, Serializer POWER 31 VSS GND Digital Ground, Serializer GROUND 7 VDD VDD Digital Voltage Supply, Serializer Logic POWER 6 VSS GND Digital Ground, Serializer Logic GROUND 42 VDD VDD Digital Voltage Supply, Serializer INPUT POWER 43 VSS GND Digital Ground, Serializer Input GROUND www.national.com 14 DS90UR241Q/DS90UR124Q DS90UR124 Pin Diagram Deserializer - DS90UR124 20194520 TOP VIEW DS90UR124 Deserializer Pin Descriptions Pin # Pin Name I/O/PWR Description LVCMOS PARALLEL INTERFACE PINS 35-38, ROUT[7:0] 41-44 LVCMOS_O Receiver Parallel Interface Data Outputs - Group 1 19-22, ROUT[15:8] 27-30 LVCMOS_O Receiver Parallel Interface Data Outputs - Group 2 7-10, 13-16 ROUT[23:16] LVCMOS_O Receiver Parallel Interface Data Outputs - Group 3 24 RCLK LVCMOS_O Parallel Interface Clock Output Pin. Strobe edge set by RRFB configuration pin. CONTROL AND CONFIGURATION PINS 55 RRFB LVCMOS_I Receiver Clock Edge Select Pin RRFB = H; ROUT LVCMOS Outputs strobed on the Rising Clock Edge. RRFB = L; ROUT LVCMOS Outputs strobed on the Falling Clock Edge. 60 REN LVCMOS_I Receiver Data Enable REN = H; ROUT[23-0] and RCLK are Enabled (ON). REN = L; ROUT[23-0] and RCLK are Disabled (OFF), Receiver ROUT[23-0] and RCLK Outputs are in TRI-STATE, PLL still operational and locked to TCLK. 48 RPWDNB LVCMOS_I Receiver Power Down Bar RPWDNB = H; Receiver is Enabled and ON RPWDNB = L; Receiver is in power down mode (Sleep), ROUT[23-0], RCLK, and LOCK are in TRI-STATE stand-by mode, PLL is shutdown to minimize power consumption. 15 www.national.com DS90UR241Q/DS90UR124Q Pin # Pin Name I/O/PWR Description 49 PTOSEL LVCMOS_I Progressive Turn On Operation Selection PTO = H; ROUT[23:0] are grouped into three groups of eight, with each group switching about 1 UI to 2 UI apart relative to RCLK. (Figure 15) PTO = L; PTO Spread Mode, ROUT[23:0] outputs are spread 1 UI to 2 UI and RCLK spread 1 UI. (Figure 16) See Applications Informations section for more details. 63 RAOFF LVCMOS_I Randomizer Control Input Pin (See Table 2 for more details.) RAOFF = H, Backwards compatible mode for use with DS90C241 Serializer. RAOFF = L; Additional randomization ON (Default), Selects 2E7 LSFR setting. 64 SLEW LVCMOS_I LVCMOS Output Slew Rate Control SLEW = L; Low drive output at 2 mA (default) SLEW = H; High drive output at 4 mA 23 LOCK LVCMOS_O LOCK indicates the status of the receiver PLL LOCK = H; receiver PLL is locked LOCK = L; receiver PLL is unlocked, ROUT[23-0] and RCLK are at TRI-STATE. 50 RES0 LVCMOS_I Reserved. This pin MUST be tied LOW. NC No Connection. Pins are not physically connected to the die. Recommendation is to leave pin open or tie it to LOW. 1-6, RES0 17, 18, 33, 34 BIST MODE PINS(See Applications Informations section for more details.) 61 BISTEN LVCMOS_I Control Pin for BIST Mode Enable BISTEN = L; Default at Low, Normal Mode. BISTEN = H; BIST mode active. When BISTEN = H and DS90UR241 DIN[23:0] = Low or Floating; device will go to BIST mode accordingly. Check PASS output pin for test status. 62 BISTM LVCMOS_I BIST Mode selection. Control pin for which Deserializer is set for BIST reporting mode. BISTM = L; Default at Low, Status of all ROUT with respective bit error on cycle-by-cycle basis BISTM = H; Total accumulated bit error count provided on ROUT[7:0] (binary counter up to 255) 45 PASS LVCMOS_O Pass flag output for @Speed BIST Test operation. PASS = L; BIST failure PASS = H; LOCK = H before BIST can be enabled, then 1x10-9 error rate achieved across link. LVDS SERIAL INTERFACE PINS 53 RIN+ LVDS_I Receiver LVDS True (+) Input -- This input is intended to be terminated with a 100 load to the RIN+ pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor. 54 RIN- LVDS_I Receiver LVDS Inverted (-) Input -- This input is intended to be terminated with a 100 load to the RIN- pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor. POWER / GROUND PINS 51 VDD VDD Analog LVDS Voltage Supply, POWER 52 VSS GND Analog LVDS GROUND 59 VDD VDD Analog Voltage Supply, PLL POWER 58 VSS GND Analog Ground, PLL GROUND 57 VDD VDD Analog Voltage supply, PLL VCO POWER 56 VSS GND Analog Ground, PLL VCO GROUND 32 VDD VDD Digital Voltage Supply, LOGIC POWER 31 VSS GND Digital Ground, Logic GROUND 46 VDD VDD Digital Voltage Supply, LOGIC POWER 47 VSS GND Digital Ground, LOGIC GROUND 40 VDD VDD Digital Voltage Supply, LVCMOS Output POWER 39 VSS GND Digital Ground, LVCMOS Output GROUND 26 VDD VDD Digital Voltage Supply, LVCMOS Output POWER 25 VSS GND Digital Ground, LVCMOS Output GROUND 11 VDD VDD Digital Voltage Supply, LVCMOS Output POWER 12 VSS GND Digital Ground, LVCMOS Output GROUND www.national.com 16 The DS90UR241 Serializer and DS90UR124 Deserializer chipset is an easy-to-use transmitter and receiver pair that sends 24-bits of parallel LVCMOS data over a single serial LVDS link from 120 Mbps to 1.03 Gbps throughput. The DS90UR241 transforms a 24-bit wide parallel LVCMOS data into a single high speed LVDS serial data stream with embedded clock and scrambles / DC Balances the data to enhance signal quality to support AC coupling. The DS90UR124 receives the LVDS serial data stream and converts it back into a 24-bit wide parallel data and recovered clock. The 24-bit Serializer/Deserializer chipset is designed to transmit data up to 10 meters over shielded twisted pair (STP) at clock speeds from 5 MHz to 43MHz. The Deserializer can attain lock to a data stream without the use of a separate reference clock source; greatly simplifying system complexity and overall cost. The Deserializer synchronizes to the Serializer regardless of data pattern, delivering true automatic "plug and lock" performance. It will lock to the incoming serial stream without the need of special training patterns or sync characters. The Deserializer recovers the clock and data by extracting the embedded clock information and validating data integrity from the incoming data stream and then deserializes the data. The Deserializer monitors the incoming clock information, determines lock status, and asserts the LOCK output high when lock occurs. In addition the Deserializer also supports an optional @SPEED BIST (Built In Self Test) mode, BIST error flag, and LOCK status reporting pin. Signal quality on the wide parallel output is controlled by the SLEW control and bank slew (PTOSEL) inputs to help reduce noise and system EMI. Each device has a power down control to enable efficient operation in various applications. DATA TRANSFER After Serializer lock is established, the inputs DIN0- DIN23 are used to input data to the Serializer. Data is clocked into the Serializer by the TCLK input. The edge of TCLK used to strobe the data is selectable via the TRFB pin. TRFB high selects the rising edge for clocking data and low selects the falling edge. The Serializer outputs (DOUT) are intended to drive point-to-point connections. CLK1, CLK0, DCA, DCB are four overhead bits transmitted along the single LVDS serial data stream (Figure 22). The CLK1 bit is always high and the CLK0 bit is always low. The CLK1 and CLK0 bits function as the embedded clock bits in the serial stream. DCB functions as the DC Balance control bit. It does not require any pre-coding of data on transmit side. The DC Balance bit is used to minimize the short and longterm DC bias on the signal lines. This bit operates by selectively sending the data either unmodified or inverted. The DCA bit is used to validate data integrity in the embedded data stream. Both DCA and DCB coding schemes are integrated and automatically performed within Serializer and Deserializer. The chipset supports clock frequency ranges of 5 MHz to 43 MHz. Every clock cycle, 24 databits are sent along with 4 additional overhead control bits. Thus the line rate is 1.20 Gbps maximum (140Mbps minimum). The link is extremely efficient at 86% (24/28). Twenty five (24 data + 1 clock) plus associated ground signals are reduced to only 1 single LVDS pair providing a compression ratio of better then 25 to 1. In the serialized data stream, data/embedded clock & control bits (24+4 bits) are transmitted from the Serializer data output (DOUT) at 28 times the TCLK frequency. For example, if TCLK is 43 MHz, the serial rate is 43 x 28 = 1.20 Giga bits per second. Since only 24 bits are from input data, the serial "payload" rate is 24 times the TCLK frequency. For instance, if TCLK = 43 MHz, the payload data rate is 43 x 24 = 1.03 Gbps. TCLK is provided by the data source and must be in the range of 5 MHz to 43 MHz nominal. The Serializer outputs (DOUT) can drive a point-to-point connection as shown in Figure 21. The outputs transmit data when the enable pin (DEN) is high and TPWDNB is high. The DEN pin may be used to TRI-STATE the outputs when driven low. When the Deserializer channel attains lock to the input from a Serializer, it drives its LOCK pin high and synchronously delivers valid data and recovered clock on the output. The Deserializer locks onto the embedded clock, uses it to generate multiple internal data strobes, and then drives the recovered clock to the RCLK pin. The recovered clock (RCLK output pin) is synchronous to the data on the ROUT[23:0] pins. While LOCK is high, data on ROUT[23:0] is valid. Otherwise, ROUT[23:0] is invalid. The polarity of the RCLK edge is controlled by the RRFB input. ROUT[23:0], LOCK and RCLK outputs will each drive a maximum of 4 pF load with a 43 MHz clock. REN controls TRI-STATE for ROUTn and the RCLK pin on the Deserializer. INITIALIZATION AND LOCKING MECHANISM Initialization of the DS90UR241 and DS90UR124 must be established before each device sends or receives data. Initialization refers to synchronizing the Serializer's and Deserializer's PLL's together. After the Serializers locks to the input clock source, the Deserializer synchronizes to the Serializers as the second and final initialization step. Step 1: When VDD is applied to both Serializer and/or Deserializer, the respective outputs are held in TRI-STATE and internal circuitry is disabled by on-chip power-on circuitry. When VDD reaches VDD OK (~2.2V) the PLL in Serializer begins locking to a clock input. For the Serializer, the local clock is the transmit clock, TCLK. The Serializer outputs are held in TRI-STATE while the PLL locks to the TCLK. After locking to TCLK, the Serializer block is now ready to send data patterns. The Deserializer output will remain in TRI-STATE while its PLL locks to the embedded clock information in serial data stream. Also, the Deserializer LOCK output will remain low until its PLL locks to incoming data and sync-pattern on the RIN pins. Step 2: The Deserializer PLL acquires lock to a data stream without requiring the Serializer to send special patterns. The Serializer that is generating the stream to the Deserializer will automatically send random (non-repetitive) data patterns during this step of the Initialization State. The Deserializer will lock onto embedded clock within the specified amount of time. An embedded clock and data recovery (CDR) circuit locks to the incoming bit stream to recover the high-speed receive bit clock and re-time incoming data. The CDR circuit expects a coded input bit stream. In order for the Deserializer to lock to a random data stream from the Serializer, it performs a series 17 www.national.com DS90UR241Q/DS90UR124Q of operations to identify the rising clock edge and validates data integrity, then locks to it. Because this locking procedure is independent on the data pattern, total random locking duration may vary. At the point when the Deserializer's CDR locks to the embedded clock, the LOCK pin goes high and valid RCLK/data appears on the outputs. Note that the LOCK signal is synchronous to valid data appearing on the outputs. The Deserializer's LOCK pin is a convenient way to ensure data integrity is achieved on receiver side. Functional Description DS90UR241Q/DS90UR124Q and 100M. Values less than 6k should not be used. A lower input resistor value on the "PRE" pin increases the magnitude of dynamic current during data transition. The additional source current is based on the following formula: PRE = (RPRE 6k); IMAX = [48 / RPRE]. For example if Rpre = 15k , then the Pre-Emphasis current is increase by an additional 3.2 mA. The amount of Pre-Emphasis for a given media will depend on the transmission distance of the application. In general, too much Pre-Emphasis can cause over or undershoot at the receiver input pins. This can result in excessive noise, crosstalk and increased power dissipation. For short cables or distances, Pre-Emphasis may not be required. Signal quality measurements are recommended to determine the proper amount of Pre-Emphasis for each application. RESYNCHRONIZATION If the Deserializer loses lock, it will automatically try to re-establish lock. For example, if the embedded clock edge is not detected one time in succession, the PLL loses lock and the LOCK pin is driven low. The Deserializer then enters the operating mode where it tries to lock to a random data stream. It looks for the embedded clock edge, identifies it and then proceeds through the locking process. The logic state of the LOCK signal indicates whether the data on ROUT is valid; when it is high, the data is valid. The system may monitor the LOCK pin to determine whether data on the ROUT is valid. POWERDOWN The Powerdown state is a low power sleep mode that the Serializer and Deserializer may use to reduce power when no data is being transferred. The TPWDNB and RPWDNB are used to set each device into power down mode, which reduces supply current to the A range. The Serializer enters powerdown when the TPWDNB pin is driven low. In powerdown, the PLL stops and the outputs go into TRI-STATE, disabling load current and reducing current supply. To exit Powerdown, TPWDNB must be driven high. When the Serializer exits Powerdown, its PLL must lock to TCLK before it is ready for the Initialization state. The system must then allow time for Initialization before data transfer can begin. The Deserializer enters powerdown mode when RPWDNB is driven low. In powerdown mode, the PLL stops and the outputs enter TRI-STATE. To bring the Deserializer block out of the powerdown state, the system drives RPWDNB high. Both the Serializer and Deserializer must reinitialize and relock before data can be transferred. The Deserializer will initialize and assert LOCK high when it is locked to the embedded clock. AC-COUPLING AND TERMINATION The DS90UR241 and DS90UR124 supports AC-coupled interconnects through integrated DC balanced encoding/decoding scheme. To use the Serializer and Deserializer in an AC coupled application, insert external AC coupling capacitors in series in the LVDS signal path as illustrated in Figure 21. The Deserializer input stage is designed for AC-coupling by providing a built-in AC bias network which sets the internal VCM to +1.8V. With AC signal coupling, capacitors provide the ac-coupling path to the signal input. For the high-speed LVDS transmissions, the smallest available package should be used for the AC coupling capacitor. This will help minimize degradation of signal quality due to package parasitics. The most common used capacitor value for the interface is 100 nF (0.1 uF) capacitor. NPO class 1 or X7R class 2 type capacitors are recommended. 50 WVDC should be the minimum used for the best system-level ESD performance. A termination resistor across DOUT and RIN is also required for proper operation to be obtained. The termination resistor should be equal to the differential impedance of the media being driven. This should be in the range of 90 to 132 Ohms. 100 Ohms is a typical value common used with standard 100 Ohm transmission media. This resistor is required for control of reflections and also completes the current loop. It should be placed as close to the Serializer DOUT outputs and Deserializer RIN inputs to minimize the stub length from the pins. To match with the deferential impedance on the transmission line, the LVDS I/O are terminated with 100 Ohm resistors on Serializer DOUT outputs pins and Deserializer RIN input pins. TRI-STATE For the Serializer, TRI-STATE is entered when the DEN or TPWDNB pin is driven low. This will TRI-STATE both driver output pins (DOUT+ and DOUT-). When DEN is driven high, the serializer will return to the previous state as long as all other control pins remain static (TPWDNB, TRFB). When you drive the REN or RPWDNB pin low, the Deserializer enters TRI-STATE. Consequently, the receiver output pins (ROUT0-ROUT23) and RCLK will enter TRI-STATE. The LOCK output remains active, reflecting the state of the PLL. The Deserializer input pins are high impedance during receiver powerdown (RPWDNB low) and power-off (VDD = 0V). Receiver Termination Option 1 A single 100 Ohm termination resistor is placed across the RIN pins (see Figure 21). This provides the signal termination at the Receiver inputs. Other options may be used to increase noise tolerance. PRE-EMPHASIS The DS90UR241 features a Pre-Emphasis function used to compensate for long or lossy transmission media. Cable drive is enhanced with a user selectable Pre-Emphasis feature that provides additional output current during transitions to counteract cable loading effects. The transmission distance will be limited by the loss characteristics and quality of the media. Pre-Emphasis adds extra current during LVDS logic transition to reduce the cable loading effects and increase driving distance. In addition, Pre-Emphasis helps provide faster transitions, increased eye openings, and improved signal integrity. The ability of the DS90UR241 to use the Pre-Emphasis feature will extend the transmission distance up to 10 meters in most cases. To enable the Pre-Emphasis function, the "PRE" pin requires one external resistor (Rpre) to Vss in order to set the additional current level. Values of Rpre should be between 6k www.national.com Receiver Termination Option 2 For additional EMI tolerance, two 50 Ohm resistors may be used in place of the single 100 Ohm resistor. A small capacitor is tied from the center point of the 50 Ohm resistors to ground (see Figure 23). This provides a high-frequency low impedance path for noise suppression. Value is not critical, 4.7nF maybe used with general applications. Receiver Termination Option 3 For high noise environments an additional voltage divider network may be connected to the center point. This has the advantage of a providing a DC low-impedance path for noise suppression. Use resistor values in the range of 100-2K 18 transition to HIGH once a BER of 1x10-9 is achieved across the transmission link. BACKWARDS COMPATIBLE MODE WITH DS90C241 AND DS90C124 The RAOFF pin allows a backward compatible mode with DS90C241/DS90C124 devices. To interface with either DS90C241 Serializer or DS90C124 Deserializer, the RAOFF pin on DS90UR241 or DS90UR124 must be tied HIGH to disable the additional LSFR coding. For normal operation directly with DS90UR241 to DS90UR124, RAOFF pins are set LOW. See Table 1 and Table 2 for more details. SIGNAL QUALITY ENHANCERS The DS90UR124 Deserializer supports two signal quality enhancers. The SLEW pin is used to increase the drive strength of the LVCMOS outputs when driving heavy loads. SLEW allows output drive strength for high or low current drive. Default setting is LOW for low drive at 2 mA and HIGH for high drive at 4 mA. There are two types of Progressive Turn-On modes (Fixed and PTO Frequency Spread) to help reduce EMI, simultaneous switching noise, and system ground bounce. The PTOSEL pin introduces bank skew in the data/clock outputs to limit the number of outputs switching simultaneously. For Fixed-PTO mode, the Deserializer ROUT[23:0] outputs are grouped into three groups of eight, with each group switching about 2 or 1 UI apart in phase from RCLK for Group 1 and Groups 2, 3 respectively (see Figure 15). In the PTO Frequency Spread mode, ROUT[23:0] are also grouped into three groups of eight, with each group is separated out of phase with the adjacent groups (see Figure 16) per every 4 cycles. Note that in the PTO Frequency Spread operating mode RCLK is also spreading and separated by 1 UI. Applications Information USING THE DS90UR241 AND DS90UR124 The DS90UR241/DS90UR124 Serializer/Deserializer (SERDES) pair sends 24 bits of parallel LVCMOS data over a serial LVDS link up to 1.03 Gbps. Serialization of the input data is accomplished using an on-board PLL at the Serializer which embeds clock with the data. The Deserializer extracts the clock/control information from the incoming data stream and deserializes the data. The Deserializer monitors the incoming clock information to determine lock status and will indicate lock by asserting the LOCK output high. DISPLAY APPLICATION The DS90UR241/124 chipset is intended for interface between a host (graphics processor) and a Display. It supports an 18-bit color depth (RGB666) and up to 1280 X 480 display formats. In a RGB666 configuration 18 color bits (R[5:0], G [5:0], B[5:0]), Pixel Clock (PCLK) and three control bits (VS, HS and DE) along with three spare bits are supported across the serial link with PCLK rates from 5 to 43 MHz. @SPEED-BIST TEST FEATURE To assist vendors with test verification, the DS90UR241/ DS90UR124 is equipped with built-in self-test (BIST) capability to support both system manufacturing and field diagnostics. BIST mode is intended to check the entire high-speed serial link at full link-speed, without the use of specialized and expensive test equipment. This feature provides a simple method for a system host to perform diagnostic testing of both Serializer and Deserializer. The BIST function is easily configured through the 2 control pins on the DS90UR124. When the BIST mode is activated, the Serializer has the ability to transfer an internally generated PRBS data pattern. This pattern traverses across interconnecting links to the Deserializer. The DS90UR124 includes an on-chip PRBS pattern verification circuit that checks the data pattern for bit errors and reports any errors on the data output pins on the Deserializer. The @SPEED-BIST feature uses 2 signal pins (BISTEN and BISTM) on the DS90UR124 Deserializer. The BISTEN and BISTM pins together determine the functions of the BIST mode. The BISTEN signal (HIGH) activates the test feature on the Deserializer. After the BIST mode is enabled, all the data input channels DIN[23:0] on the DS90UR241 Serializer must be set logic LOW or floating in order for Deserializer to start accepting data. An input clock signal (TCLK) for the Serializer must also be applied during the entire BIST operation. The BISTM pin selects error reporting status mode of the BIST function. When BIST is configured in the error status mode (BISTM = LOW), each of the ROUT[23:0] outputs will correspond to bit errors on a cycle-by-cycle basis. The result of bit mismatches are indicated on the respective parallel inputs on the ROUT[23:0] data output pins. In the BIST errorcount accumulator mode (BISTM = HIGH), an 8-bit counter on ROUT[7:0] is used to represent the number of errors detected (0 to 255 max). The successful completion of the BIST test is reported on the PASS pin on the Deserializer. The Deserializer's PLL must first be locked to ensure the PASS status is valid. The PASS status pin will stay LOW and then TYPICAL APPLICATION CONNECTION Figure 18 shows a typical application of the DS90UR241 Serializer (SER). The LVDS outputs utilize a 100 ohm termination and 100nF coupling capacitors to the line. Bypass capacitors are placed near the power supply pins. At a minimum, three 0.1uF capacitors should be used for local bypassing. A system GPO (General Purpose Output) controls the TPWDNB pin. In this application the TRFB pin is tied High to latch data on the rising edge of the TCLK. The DEN signal is not used and is tied High also. The application is to the companion Deserializer (DS90UR124) so the RAOFF pin is tied low to scramble the data and improve link signal quality. In this application the link is typical, therefore the VODSEL pin is tied Low for the standard LVDS swing. The pre-emphasis input utilizes a resistor to ground to set the amount of preemphasis desired by the application. Figure 20shows a typical application of the DS90UR124 Deserializer (DES). The LVDS inputs utilize a 100 ohm termination and 100nF coupling capacitors to the line. Bypass capacitors are placed near the power supply pins. At a minimum, four 0.1uF capacitors should be used for local bypassing. A system GPO (General Purpose Output) controls the RPWDNB pin. In this application the RRFB pin is tied High to strobe the data on the rising edge of the RCLK. The REN signal is not used and is tied High also. The application is to the companion Serializer (DS90UR241) so the RAOFF pin is tied low to descramble the data. Output (LVCMOS) signal quality is set by the SLEW pin, and the PTOSEL pin can be used to reduce simultaneous output switching by introducing a small amount of delay between output banks. 19 www.national.com DS90UR241Q/DS90UR124Q for the pullup and pulldown. Ratio the resistor values to bias the center point at 1.8V. For example (see Figure 24): VDD=3.3V, Rpullup=1K, Rpulldown=1.2K; or Rpullup=100, Rpulldown= 120 (strongest). The smaller values will consume more bias current, but will provide enhanced noise suppression. DS90UR241Q/DS90UR124Q 20194522 FIGURE 18. DS90UR241 Typical Application Connection dia needs be terminated at both ends of the transmitter and receiver pair. Interconnect for LVDS typically has a differential impedance of 100 Ohms. Use cables and connectors that have matched differential impedance to minimize impedance discontinuities. In most applications that involve cables, the transmission distance will be determined on data rates involved, acceptable bit error rate and transmission medium. The resulting signal quality at the receiving end of the transmission media may be assessed by monitoring the differential eye opening of the serial data stream. The Receiver Input Tolerance and Differential Threshold Voltage specifications define the acceptable data eye opening. A differential probe should be used to measure across the termination resistor at the DS90UR124 inputs. Figure 19 illustrates the eye opening and relationship to the Receiver Input Tolerance and Differential Threshold Voltage specifications POWER CONSIDERATIONS An all LVCMOS design of the Serializer and Deserializer makes them inherently low power devices. Additionally, the constant current source nature of the LVDS outputs minimize the slope of the speed vs. IDD curve of LVCMOS designs. NOISE MARGIN The Deserializer noise margin is the amount of input jitter (phase noise) that the Deserializer can tolerate and still reliably recover data. Various environmental and systematic factors include: Serializer: VDD noise, TCLK jitter (noise bandwidth and out-of-band noise) Media: ISI, VCM noise Deserializer: VDD noise For a graphical representation of noise margin, please see . TRANSMISSION MEDIA The Serializer and Deserializer are to be used in point-to-point configuration, through a PCB trace, or through twisted pair cable. In a point-to-point configuration, the transmission mewww.national.com 20 20194528 FIGURE 19. Receiver Input Eye Opening 21 www.national.com DS90UR241Q/DS90UR124Q LIVE LINK INSERTION The Serializer and Deserializer devices support live pluggable applications. The automatic receiver lock to random data "plug & go" hot insertion capability allows the DS90UR124 to attain lock to the active data stream during a live insertion event. DS90UR241Q/DS90UR124Q 20194523 FIGURE 20. DS90UR124 Typical Application Connection ternal bypass capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range of 0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF to 10 uF range. Voltage rating of the tantalum capacitors should be at least 5X the power supply voltage being used. Surface mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per supply pin, locate the smaller value closer to the pin. A large bulk capacitor is recommend at the point of power entry. This is typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is recommended to connect power PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS Circuit board layout and stack-up for the LVDS SERDES devices should be designed to provide low-noise power feed to the device. Good layout practice will also separate high frequency or high-level inputs and outputs to minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This arrangement provides plane capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at high frequencies, and makes the value and placement of external bypass capacitors less critical. Exwww.national.com 22 mode and thus is rejected by the receivers. The tightly coupled lines will also radiate less. Termination of the LVDS interconnect is required. For pointto-point applications, termination should be located at both ends of the devices. Nominal value is 100 Ohms to match the line's differential impedance. Place the resistor as close to the transmitter DOUT outputs and receiver RIN inputs as possible to minimize the resulting stub between the termination resistor and device. LVDS INTERCONNECT GUIDELINES See AN-1108 and AN-905 for full details. * Use 100 coupled differential pairs * Use the S/2S/3S rule in spacings --S = space between the pair --2S = space between pairs --3S = space to LVCMOS signal * Minimize the number of Vias * Use differential connectors when operating above 500Mbps line speed * Maintain balance of the traces * Minimize skew within the pair * Terminate as close to the TX outputs and RX inputs as possible Additional general guidance can be found in the LVDS Owner's Manual - available in PDF format from the National web site at: www.national.com/lvds 20194518 FIGURE 21. AC Coupled Application 20194526 *Note: bits [0-23] are not physically located in positions shown above since bits [0-23] are scrambled and DC Balanced FIGURE 22. Single Serialized LVDS Bitstream* 23 www.national.com DS90UR241Q/DS90UR124Q and ground pins directly to the power and ground planes with bypass capacitors connected to the plane with via on both ends of the capacitor. Connecting power or ground pins to an external bypass capacitor will increase the inductance of the path. A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of these external bypass capacitors, usually in the range of 20-30 MHz range. To provide effective bypassing, multiple capacitors are often used to achieve low impedance between the supply rails over the frequency of interest. At high frequency, it is also a common practice to use two vias from power and ground pins to the planes, reducing the impedance at high frequency. Some devices provide separate power and ground pins for different portions of the circuit. This is done to isolate switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not required. Pin Description tables typically provide guidance on which circuit blocks are connected to which power pin pairs. In some cases, an external filter many be used to provide clean power to sensitive circuits such as PLLs. Use at least a four layer board with a power and ground plane. Locate LVCMOS signals away from the LVDS lines to prevent coupling from the LVCMOS lines to the LVDS lines. Closelycoupled differential lines of 100 Ohms are typically recommended for LVDS interconnect. The closely coupled lines help to ensure that coupled noise will appear as common- DS90UR241Q/DS90UR124Q 20194524 FIGURE 23. Receiver Termination Option 2 20194525 FIGURE 24. Receiver Termination Option 3 Truth Tables TABLE 1. DS90UR241 Serializer Truth Table TPWDNB (Pin 9) DEN (Pin 18) RAOFF (Pin 12) Tx PLL Status (Internal) LVDS Outputs (Pins 19 and 20) L X X X Hi Z H L X X Hi Z H H X Not Locked Hi Z H H L Locked Serialized Data with Embedded Clock (DS90UR124 compatible) H H H Locked Serialized Data with Embedded Clock (DS90C124 compatible) www.national.com 24 RPWDNB (Pin 48) REN (Pin 60) RAOFF (Pin 63) Rx PLL Status (Internal) ROUTn and RCLK (See Pin Diagram) LOCK (Pin 23) L X X X Hi Z Hi Z H L X X Hi Z L = PLL Unocked; H = PLL Locked H H X Not Locked Hi Z L H H L Locked Data and RCLK Active (DS90UR241 compatible) H H H H Locked Data and RCLK Active (DS90C241 compatible) H Revision History * October 4, 2011Updated Applications Information for Transmission Media. Added figure describing Receiver Input Eye Opening 25 www.national.com DS90UR241Q/DS90UR124Q TABLE 2. DS90UR124 Deserializer Truth Table DS90UR241Q/DS90UR124Q Physical Dimensions inches (millimeters) unless otherwise noted Dimensions show in millimeters only NS Package Number VBC48A Dimensions show in millimeters only NS Package Number VEC64A www.national.com 26 DS90UR241Q/DS90UR124Q Notes 27 www.national.com DS90UR241Q/DS90UR124Q 5-43 MHz DC-Balanced 24-Bit FPD-Link II Serializer and Deserializer Chipset Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage References www.national.com/vref Design Made Easy www.national.com/easy www.national.com/powerwise Applications & Markets www.national.com/solutions Mil/Aero www.national.com/milaero PowerWise(R) Solutions Serial Digital Interface (SDI) www.national.com/sdi Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic PLL/VCO www.national.com/wireless www.national.com/training PowerWise(R) Design University THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2011 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated