SPECIFICATION
MODEL
RATED CURRENT
RATED POWER
OUTPUT VOLTAGE RANGE
Note.4
OUTPUT
CURRENT ADJ. RANGE
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE Note.3
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS Note.5
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER TEMPERATURE
OVER VOLTAGE
Can be adjusted by internal potentiometer A type only
30ms at full load 480VAC / 347VAC
180 ~ 528VAC 254VDC ~ 747VDC
47 ~ 63Hz
0.38A / 347VAC 0.28A / 480VAC
-40 ~ +70 (Refer to "Derating Curve")℃
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
186.1K hrs min. MIL-HDBK-217F (25 )℃
236*68*38.8mm (L*W*H)
RIPPLE & NOISE (max.)
Note.2
ENVIRONMENT
SAFETY &
EMC
PROTECTION
300 ~ 320V
Shut down o/p voltage, recovers automatically after temperature goes down
Protection type : Shut down o/p voltage with auto-recovery or re-power on to recovery
SHORT CIRCUIT
91%
HVGC-100-350 HVGC-100-700
1Vp-p 0.5Vp-p
1. All parameters NOT specially mentioned are measured at 347VAC input, rated load and 25 of ambient temperature.℃
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 2.2uf parallel capacitor.
3. Derating may be needed under low input voltages. Please check the static characteristics for more details.
4. Please refer to "DRIVING METHODS OF LED MODULE" DIMMING OPERATION" and ."
5. Safety and EMC design refer to EN60598-1, CNS15233, GB7000.1.
6. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the
complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.
7. Refer to warranty statement.
8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently
connected to the mains.
Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level (surge 4KV), criteria A
Constant current limiting, recovers automatically after fault condition is removed
<0.75mA / 480VAC
210 ~ 350mA 420 ~ 700mA
350mA
99.75W
29 ~ 285V
1.18Kg; 12pcs/15.2Kg/0.74CUFT
I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
UL8750 CSA C22.2 No. 250.0-08, TUV EN61347-1, EN61347-2-13, approved ; design refer to UL60950-1, TUV EN60950-1,IP65 or IP67
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH℃
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
91%
150 ~ 160V
700mA
99.4W
15 ~ 142V
■ Features :
A : IP65 rated. Constant current level can be adjusted through internal potentiometer.
B : IP67 rated. Constant current level adjustable through output cable with 0~10Vdc or 10V PWM signal or resistance.
D
(option) : IP67 rated. Timer dimming function, contact MEAN WELL for details.
Constant current design
Wide input range 180~528VAC
Built-in active PFC function
High efficiency up to 91%
Protections: Short circuit / Over voltage / Over temperature
Cooling by free air convection
OCP point adjustable through output cable or internal potentiometer
IP67 / IP65 design for indoor or outdoor installations
Three in one dimming function (0~10Vdc or 10V PWM signal or resistance)
Suitable for LED lighting and street lighting applications
Compliance to worldwide safety regulations for lighting
Suitable for dry / damp / wet locations
5 years warranty (Note.7)
FMM
110
IP65 IP67
HVGC-100-350 A
100W Single Output LED Power Supply HVGC-100 series
File Name:HVGC-100-SPEC 2015-05-26
EMC IMMUNITY
EMC EMISSION
CURRENT ACCURACY ±5.0%
PF 0.98/230VAC, PF 0.98/277VAC, PF 0.97/347VAC, PF 0.93/480VAC at full load (Please refer to "Power Factor Characteristic" curve)≧≧≧≧
Compliance to EN55015, EN61000-3-2 Class C ( 50% load) ; EN61000-3-3, FCC part 15 class B≧
COLD START 25A(t =900 s measured at 50% I ) at 480VACwidth peak
μ
THD<20% when output loading 50% at 230VAC/277VAC/347VAC input ; THD<20% when output loading 75% at 480VAC input≧≧
TOTAL HARMONIC DISTORTION
500ms, 80ms 230VAC / 347VAC / 480VAC at full load ; B type 500ms, 280ms 230VAC / 347VAC / 480VAC at 95% load
MAX. No. of PSUs on 16A
CIRCUIT BREAKER 5 units (circuit breaker of type B) / 8 units (circuit breaker of type C) at 480VAC
Mechanical Specification Case No.994 Unit:mm
236
212
※IP65 rated. Constant current level can be adjusted through internal potentiometer.
(Can access by removing the rubber stopper on the case.)
A Type:(HVGC-100-_A)
104.4
Tcase
34
※T case: Max. Case Temperature.
※IP67 rated. Timer dimming function, contact MEAN WELL for details.
D Type(option):(HVGC-100-_D)
B Type:(HVGC-100-_B)
300 20±
38.8
STW 18AWG 3C×
12
9.6
9.49.4 34.2
68
ψ×4.2 4PL
300 20±
DIM+(Blue)
DIM-(White)
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
UL2517 18AWG 2C×
SJTW 18AWG 2C×
-V(Black)
+V(Red)
300 20±
FG (Green/Yellow)
SJTW 18AWG 2C×
SJTW 18AWG 2C×
STW 18AWG 3C×
236
236
212
212
AC/L(Brown)
AC/N(Blue)
12
9.6
9.49.4 34.2
68
ψ×4.2 4PL
300 20±
300 20±
38.8
Io
ADJ.
104.4
104.4
Tcase
Tcase
34
34
※T case: Max. Case Temperature.
※T case: Max. Case Temperature.
300 20±
FG (Green/Yellow)
38.8
STW 18AWG 3C×
AC/L(Brown)
AC/N(Blue)
12
9.6
9.49.4 34.2
68
ψ×4.2 4PL
-V(Black)
-V(Black)
+V(Red)
+V(Red)
100W Single Output LED Power Supply HVGC-100 series
File Name:HVGC-100-SPEC 2015-05-26
0.80
0.82
0.84
0.86
0.88
0.90
0.92
0.94
0.96
0.98
1.00
50% 60% 70% 80% 90% 100%
480V
347V
277V
230V
Derating Curve Static Characteristics
INPUT VOLTAGE (V) 60Hz
180 347 480 528
100
90
80
70
60
50
40
LOAD (%)
fosc : 80KHz
Block Diagram
AMBIENT TEMPERATURE ( )℃
LOAD (%)
-40 -25 -10 0 15 30 50 60 70
20
40
60
80
100
(HORIZONTAL)
Power Factor Characteristic
PF
LOAD
Constant Current Mode
(100W)
DIM+
(B Type)
DIM-
DETECTION
PWM & PFC CIRCUIT
O.L.P.
EMI FILTER
RECTIFIERS
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
-V
I/P
FG
CONTROL
O.V.P.
&
O.L.P.
PFC
CIRCUIT
PFC
CONTROL
O.T.P.
100W Single Output LED Power Supply HVGC-100 series
File Name:HVGC-100-SPEC 2015-05-26
0.58
0.62
0.66
0.70
0.74
0.78
0.82
0.86
0.90
0.94
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
480V
347V
277V
230V
EFFICIENCY vs LOAD (HVGC-100-700 Model)
HVGC-100 series possess superior working efficiency that up to 91% can be reached in field applications.
LOAD
EFFICIENCY (%)
DRIVING METHODS OF LED MODULE
A typical LED power supply may work in "constant current mode (CC)" to drive the LEDs.
Mean Well's LED power supply with CC characteristic can be operated at CC mode (direct drive).
In the constant current region, the highest voltage at the output of the driver
depends on the configuration of the end systems.
Should there be any compatibility issues, please contact MEAN WELL.
Typical LED power supply I-V curve
Vo(%)
100
50 100 Io (%)
Constant
Current region
100W Single Output LED Power Supply HVGC-100 series
File Name:HVGC-100-SPEC 2015-05-26
HVGC-100
DIMMING OPERATION (for B-type only)
DIM+(Blue)
DIM-(White)
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue)
※Reference resistance value for output current adjustment (Typical)
※Built-in 3 in 1 dimming function, IP67 rated. Output constant current level can be adjusted through output cable by connecting a resistance or
0 ~ 10Vdc or 10V PWM signal between DIM+ and DIM-.
※Please DO NOT connect "DIM-" to "-V".
60KΩ
60%
60%
10KΩ
10K /NΩ20K /NΩ30K /NΩ40K /NΩ50K /NΩ60K /NΩ70K /NΩ80K /NΩ90K /NΩ
100K /N
Ω
Single driver
Multiple drivers
(N=driver quantity for synchronized
dimming operation)
1V 4V 7V2V 5V 8V3V 6V 9V 10V
10%
10%
20KΩ
20%
20%
30KΩ
30%
30%
40KΩ
40%
40%
50KΩ
50%
50%
70KΩ
70%
70%
80KΩ
80%
80%
90KΩ100KΩOPEN
OPEN
OPEN
90%
90%
100%
100%
Resistance
value
Dimming value
Percentage of rated current
Percentage of rated current
※0 ~ 10V dimming function for output current adjustment (Typical)
60%
60%
10%
10%
20%
20%
30%
30%
40%
40%
50%
50%
70%
70%
80%
80%
90%
90%
100%
100%
Duty value
Percentage of rated current
95%~108%
-----
95%~108%
95%~108%
※10V PWM signal for output current adjustment (Typical): Frequency range :100Hz ~ 3KHz
◎Waterproof connector
Waterproof connector can be assembled on the output cable of HVGC-100 to operate in dry/wet/damp or outdoor environment.
HVGC-100
I/P O/P
LED Lamp
AC
source
Pin Configuration (Female) Pin Configuration (Female)
Size Size
M12 M15
4-PIN
5A/PIN
M12-04Order No. Order No.
10A max.Suitable Current Suitable Current
5-PIN
5A/PIN
M12-05
10A max.
2-PIN
12A/PIN
M15-02
12A max.
WATERPROOF CONNECTION
-V(Black)
+V(Red)
Short
Short
0V
0%
0%
0%
0%
◎Dimming Characteristic
Percentage of rated current(%)
Output Current
Duty cycle of 10V PWM (frequency range = 100~3KHz)
Short~100K resistanceΩ
0~10V
※Note : The output current drops down to 0% when the dimming input is about
6K or 0.6Vdc, or 10V PWM signal with 6% duty cycle.Ω
Dimming input
100% when DIM+/DIM- are open circuit.
Non-Linear
0V
0%
1V
10%
2V
20%
3V
30%
4V
40%
5V
50%
6V
60%
7V
70%
8V
80%
9V
90%
10V
100%
10%
0%
20%
30%
40%
50%
60%
70%
80%
90%
100%
Short
10K 20K 30K 40K 50K 60K 70K 80K 90K 100K
Note
100W Single Output LED Power Supply HVGC-100 series
File Name:HVGC-100-SPEC 2015-05-26
※Output voltage limit of 50%.
◎Cable Joiner
Up to four wires can be connected through this cable joiner by
soldering or clamping by tools.
66
26 20
ψ25
CJ04-2 suitable for 18AWG~22AWG
CJ04-1 suitable for 14AWG~16AWG
O/P Wires
LED Lamp
HVGC-100
※CJ04 cable joiner can be purchased independently for user's own assembly.
MEAN WELL order No. : CJ04-1, CJ04-2.
◎Junction Box(Option )
※Optional junction box available for , please contact MEAW WELL for details.A- type
150 20±
3- PF 1/2"
86
76
5
10
38.8
35
2- 5ψ
61
32 8.58.5
6
208.8
370.8
150 20±
3- PF 1/2"
68
SJTW 18AWG 2C×
STW 18AWG 3C×
FG (Green/Yellow)
AC/L(Brown)
AC/N(Blue) +V(Red)
-V(Black)
100W Single Output LED Power Supply HVGC-100 series
File Name:HVGC-100-SPEC 2015-05-26
