CHEMTRONICS(R) TDS # 1051 Technical Data Sheet Freez-It(R) Antistat PRODUCT DESCRIPTION Freez-It(R) Antistat is engineered for locating thermal intermittent electrical components or cooling printed circuit boards with minimal static generation. This circuit refrigerant system is nonflammable, residue-free and provides fast cooling action. Minimal static generation Nonflammable High heat transfer Low static generation Noncorrosive Lowers temperature to -60F (51C) Ultra pure, filtered to <0.2 microns Leaves no residue Nonabrasive on most surfaces Dries fast Contains no CFCs or HCFCs TYPICAL PRODUCT DATA AND PHYSICAL PROPERTIES Boiling Point -15.7F Surface Tension (dynes/cm @ 77F) 7.8 TYPICAL APPLICATIONS Freez-It(R) Antistat can be used to: Cool Equipment for Testing Dissipate Heat While Soldering or Desoldering Isolate Thermal Intermittent Components Test Circuit Traces for Continuity Test Printed Circuit Boards for Stress Fractures Track Static Sensitive Components Flash Point (TCC) None Vapor Density (air=1) @ 77F Solubility in Water @ 77F /1 atm Specific Gravity (water = 1 @77F) Evaporation Rate (butyl acetate=1) Appearance Odor Shelflife RoHS/WEEE Status 3.18 1.0% by weight 1.21 >1 Clear, Colorless Liquified Gas Slight Ethereal 5 years COMPATIBILITY Freez-It(R) Antistat is generally compatible with most materials used in printed circuit board fabrication, including sensitive plastics and compounds. With any circuit refrigerant, compatibility must be determined on a non-critical area prior to use. TECHNICAL & APPLICATION ASSISTANCE Compatibility Fair Good Good Good Poor Good Good Poor Good Good Fair Good Poor Material Buna-N Graphite HDPE LDPE LexanTM Neoprene Cross-Linked PE Polyacrylate Polystyrene PVC Silicone Rubber TeflonTM VitonTM Chemtronics(R) provides a technical hotline to answer your technical and application related questions. The toll free number is: 1-800-TECH-401. ENVIRONMENTAL IMPACT DATA ENVIRONMENTAL IMPACT DATA CFC HCFC CL Solv. Competitive Assessment of Freez-It Antistat Freez-It Antistat 56% Less Static 40 v/in. Competitor's Antistat Freeze Spray 0 20 40 60 80 Static Generation (V/IN.) 120 USAGE INSTRUCTIONS For industrial use only. Read MSDS carefully prior to use. No special surface preparation is required prior to using Freez-It(R)Antistat. Direct spray onto the area to instantly cool components, circuit boards or adhesives. For optimum performance and pin point control, use Freez-It(R)Antistat with the attached extension tube. AVAILABILITY ES1051 ES1551 10 oz. Aerosol 15 oz. Aerosol VOC HFC ODP 0.9% 99.1% 0.0 CFC, HCFC, CL. SOLV., VOC, and HFC numbers shown are the content by weight. Ozone depletion potential (ODP) is determined in accordance with the Montreal Protocol and U.S. Clean Air Act of 1990. The ODP of this product is 0.0. It is the sum of the ODP of the substances that may contribute to the depletion of stratospheric ozone, based upon the weight of each substance in the product's formulation. NOTE: 90 v/in. 100 0.0% 0.0% 0.0% This information is believed to be accurate. It is intended for professional end users having the skills to evaluate and use the data properly. CHEMTRONICS(R) does not guarantee the accuracy of the data and assumes no liability in connection with damages incurred while using it. MANUFACTURED BY: ITW CHEMTRONICS 8125 COBB CENTER DRIVE KENNESAW, GA 30152 1-770-424-4888 DISTRIBUTED BY: REV. E (06/06)