PRODUCT DESCRIPTION
Freez-It® Antistat is engineered for locating
thermal intermittent electrical components or
cooling printed circuit boards with minimal
static generation. This circuit refrigerant
system is nonflammable, residue-free and
provides fast cooling action.
Minimal static generation
Nonflammable
High heat transfer
Low static generation
Noncorrosive
Lowers temperature to -60°F (51°C)
Ultra pure, filtered to <0.2 microns
Leaves no residue
Nonabrasive on most surfaces
Dries fast
Contains no CFCs or HCFCs
TYPICAL APPLICATIONS
Freez-It® Antistat can be used to:
Cool Equipment for Testing
Dissipate Heat While Soldering or
Desoldering
Isolate Thermal Intermittent
Components
Test Circuit Traces for Continuity
Test Printed Circuit Boards for Stress
Fractures
Track Static Sensitive Components
TYPICAL PRODUCT DATA AND
PHYSICAL PROPERTIES
Boiling Point -15.7°F
Vapor Density (air=1)
@ 77°F
3.18
Solubility in Water
@ 77°F /1 atm 1.0% by weight
Specific Gravity
(water = 1 @77°F) 1.21
Evaporation Rate >1
(butyl acetate=1)
Appearance Clear, Colorless
Liquified Gas
Odor Slight Ethereal
Surface Tension
(dynes/cm @ 77°F) 7.8
Flash Point (TCC) None
Shelflife 5 years
RoHS/WEEE
Status
COMPATIBILITY
Freez-It® Antistat is generally compatible
with most materials used in printed circuit
board fabrication, including sensitive plastics
and compounds. With any circuit
refrigerant, compatibility must be determined
on a non-critical area prior to use.
TDS # 1051
CHEMTRONICS®
Technical Data Sheet
Freez-It® Antistat
Material Compatibility
Buna-N Fair
Graphite Good
HDPE Good
LDPE Good
Lexan™ Poor
Neoprene Good
Cross-Linked PE Good
Polyacrylate Poor
Polystyrene Good
PVC Good
Silicone Rubber Fair
Teflon™ Good
Viton™ Poor
Competitive Assessment of Freez-It Antistat
Freez-It Antistat
56% Less 40 v/in.
Static
Competitor’s
Antistat Freeze Spray 90 v/in.
0 20 40 60 80 100 120
Static Generation (V/IN.)
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
No special surface preparation is required
prior to using Freez-It®Antistat. Direct spray
onto the area to instantly cool components,
circuit boards or adhesives. For optimum
performance and pin point control, use
Freez-It®Antistat with the attached extension
tube.
AVAILABILITY
ES1051 10 oz. Aerosol
ES1551 15 oz. Aerosol
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics® provides a technical hotline to answer
your technical and application related questions.
The toll free number is:
1-800-TECH-401.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
CFC 0.0% VOC 0.9%
HCFC 0.0% HFC 99.1%
CL Solv. 0.0% ODP 0.0
CFC, HCFC, CL. SOLV., VOC, and HFC numbers
shown are the content by weight. Ozone depletion
potential (ODP) is determined in accordance with the
Montreal Protocol and U.S. Clean Air Act of 1990. The
ODP of this product is 0.0. It is the sum of the ODP of
the substances that may contribute to the depletion of
stratospheric ozone, based upon the weight of each
substance in the product’s formulation.
NOTE:
This information is believed to be accurate. It is intended
for professional end users having the skills to evaluate
and use the data properly. CHEMTRONICS® does not
guarantee the accuracy of the data and assumes no
liability in connection with damages incurred while using
it.
MANUFACTURED BY:
ITW CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV. E (06/06)
DISTRIBUTED BY:
