geoqnsoUuds TYPE 518D Aluminum Capacitors + 85C, Electrolytic Chips PERFORMANCE CHARACTERISTICS Operating Temperature: - 40C to + 85C. Capacitance Range: 1F to 100uF. Capacitance Tolerance: + 20% @ 120Hz, + 20C. Voltage Rating: 6.3 WVDC to 50 WVDC. Life Validation Test: After 2000 hours application of rated voltage at + 85C, capacitors meet these characteristics requirements: Leakage Current: Initial specified value or less. Capacitance Change: Within + 20% of initial value. tan 5: 200% or less of initial specified value. Shelf Test: After 1000 hours at + 85C and no load, capacitors meet the specified value for Life Validation characteristics listed. Resistance to Soldering Heat: Capacitors shall be kept on the hot plate maintained at + 250C for 30 seconds. After removing from the hot plate and restored at room temperature, they meet the following characteristics: Capacitance Plastic FEATURES way SPRAGUE Vv Chip type with .217" [5.5mm] height * Designed for surface mounting on high density PC board Applicable to automatic insertion machine using carrier tape Load life of 2000 hours at + 85C Leakage Current: Initial specified value or less. Capacitance Change: Within + 10% of initial value. tan 8: Initial specified value or less. Marking: Black print on the case top. Applicable Standards: JIS C-5141 and JIS C-5102. Leakage Current: After 2 minutes of rated voltage not more than 0.01 CV or 3A, whichever is greater. MAXIMUM IMPEDANCE RATIO ZT/Z20 @ 120Hz Rated Voltage tan 6 (WVDC) (Maximum) Z - 25C/+ 20C Z - 40C/+ 20C 6.3 0.26 4 8 10 0.20 3 8 16 0.16 2 4 25 0.14 2 4 35 0.12 2 3 50 0.12 2 3 Positive Platform 012 [0.3] @ Lot No. Voltage* aie +005 10-21 a 020 [0.5] >| +. . < y Max. = 4 4 A N | +.008 [0.2] GOD 8 E A .020 [0.5] + .008 [0.2] 4 A y \ +008 [0.2] Lt oO _y| -213+.004-.008 |. >| le A [5.4 + 0.1 - 0.2] SO 020 to .031 Negative [0.5 to 0.8] * Voltage mark for 6.3V is 6V. SD A 8 c E 157 [4.0] 071 [1.8] .169 [4.3] .169 [4.3} .039 [1.0] .197 [5.0] .083 [2.1] .209 [5.3] 209 [5.3] 054 [1.3] .248 [6.3] .094 [2.4] -260 [6.6] .260 [6.6] .087 [2.2] SPRAGUE, 678 Main Street, Sanford, ME 04073 Phone (207) 490-7243 * Fax 207-490-3906 TYPE 518D Max. RIPPLE @ + 85C CAPACITANCE RATED SURGE NOMINAL CASE SIZE 120Hz (uF) VOLTAGE VOLTAGE PART NUMBER DxL rms (mA) 1.0 50V 63V 518D105MO50HX7S 157 x .217 [4.0 x 5.5] 8.4 2.2 50V 63V 518D225M050HX7S 157 x .217 [4.0 x 5.5] 13.0 47 25V 32V 518D475M025HX7S 157 x .217 [4.0 x 5.5] 16.0 47 35V 44V 518D475M035HX7S 157 x .217 [4.0 x 5.5] 18.0 10.0 16V 20V 518D106M016HX7S 157 x 217 [4.0 x 5.5] 23.0 10.0 50V 63V 518D106M050AX7S .248 x 217 [6.3 x 5.5] 33.0 22.0 16V 20V 518D226M016JX7S 197 x .217 [5.0 x 5.5] 37.0 22.0 25V 32 V 51B8D226M025AX7S 248 x .217 [6.3 x 5.5] 42.0 22.0 35 V 4av 518D226M035AX7S 248 x .217 [6.3 x 5.5] 46.0 33.0 6.3V BV 518D336M6R3JUX7S 197 x .217 [5.0 x 5.5] 37.0 33.0 25V 32 V 518D336M025AX7S .248 x .217 [6.3 x 5.5] 52.0 47.0 6.3V BV 518D476M6R3JX7S 197 x .217 [5.0 x 5.5] 45.0 47.0 10V 13V 518D476M010AX7S .248 x .217 [6.3 x 5.5] 52.0 47.0 16V 20V 518D476M016AX7S 248 x .217 [6.3 x 5.5] 58.0 100.0 6.3V BV 518D107M6R3AX7S 248 x .217 [6.3 x 5.5] 70.0 100.0 16V 20V 518D107M016AX7S 248 x .217 [6.3 x 5.5] 86.0 SOLDERING ALLOWABLE RANGE {Numbers in brackets indicate millimeters] METHOD OF REFLOW & HOT PLATE 220 REFLOW (DEG. CENTIGRADE) ny S PEAK TEMPERATURE AT CAPACITOR TOP 0 20 40 60 REFLOW TIME (SECONDS) 230 INFRARED-RAY REFLOW 220 SIZE x Y A 200 @ .157 [4.0) .063 [1.6] 102 [2.6] .040 [1.0] 9 20 40 60 @ .197 [5.0] .063 [1.6] .118 [3.0] .055 [1.4] REFLOW TIME (SECONDS! s ) @ 248 [6.3] .063 [1.6] 138 [3.5] .083 [2.1] AIR REFLOW PEAK TEMPERATURE AT CAPACITOR TOP (DEG. CENTIGRADE) Preheating shall be done less than + 150C and for 90 seconds, respectively. Peak Temp. at Measuring Point the allowable range of reflow, please contact the factory. E z & The temperature at capacitor top shall not exceed g 200 |---- = -- wenn nnn nen nnn nny + 230C. ze 450 < * The duration for over + 200C temperature at 25 20 Seconds capacitor top shall not exceed 20 seconds. = z |<>| * The standard temperature profile differs by every W 3 Preheat Reflow reflow method. eo < p< > * If capacitors are subject to the conditions other than ui 0 = TIME (SECONDS) w ~ SPRAGUE, 678 Main Street, Sanford, ME 04073 * Phone (207) 490-7243 + Fax 207-490-3906 TYPE 518D 518D 107 M 6R3 TYPE CAPACITANCE CAPACITANCE DC VOLTAGE TOLERANCE RATING AX CASE CODE 7 $s PACKAGING CONFIGURATION This is expressed in picofarads. The M=+ 20% This is expressed in volts. Where first two digits are significant. The third is the number of zeros to follow. necessary to complete the three digit block, zeros precede the voltage rating. The letter "R" is used as a decimal point. HX = .157" x .217" 7 = Tape and Ree | | S = Surface Mount [4.0mm x 5.5mm] = .197" x .217" [5.0mm x 5.5mm] AX = .248" x 217" [6.3mm x 5.5mm} JX Carrier Tape 457 +.004 .079 + .004 157 + [2.00.1] .069 + .004 (4.0 +0.1] 059 + 004-0 {1.75 +0.1] 016 [0.4] [@ 1.5+0.1-0] > o-oo! op 0 O-O--O-O--O A ? SL w +.012 Bo A oe [0.3] +.008 [0.2)} v and Y Ay + .008 [0.2] w P Ay By Ta SIZE +.012 [0.3] +.004 [0.1] + .004 [0.1] +.008 [0.2] + ,008 [0.2] +.008 [0.2] @ .157 [4.0] 472 [12.0] .315 [8.0] 217 [5.5] 197 [5.0] .197 [5.0] .228 [5.8] @ 197 [5.0] 472 [12.0] 472 [12.0] 217 [5.5] .236 [6.0] .236 [6.0] 228 [5.8] 248 [6.3] .630 [16.0] 472 [12.0] .295 [7.5] .276 [7.0] 276 [7.0] 228 [5.8] Reel 7 |a 15.0 [@ 382.0] 5 Max. 3 ' 6 t ~-- - 01.97 $ apr sat [@ $0.0] Min. -906 [23.0] i v @D A QTY/REEL Space to -512 +.020 < . Show Remains (13.0 +0.8) <>ll 118 [3.0] 157 [4.0] | 551 [14.0] | 2000 Dia. 197 [5.0] | 554 [14.0] 1000 .248 [6.3] | .709 [18.0] 1000 SPRAGUE, 678 Main Street; Sanford, ME 04073 * Phone (207) 490-7243 Fax 207-490-3906 Aluminum Capacitors SPRAGUE 678 Main Street Sanford, ME 04073 Phone: (207) 490-7243 Fax: 207-490-3906 Vy SPRAGUE PRINTED IN U.S.A. 8/95