TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Applications * * * * 3G / 4G Wireless Infrastructure CDMA, TD-CDMA, WCDMA, LTE Repeaters PTP Radio IF Chains 28-pin 6x6mm leadless SMT package Product Features * * * * * * * * * Functional Block Diagram 1.4-2.7 GHz Frequency Range 31.7 dB Maximum Gain at 2 GHz 31.5 dB Gain Range in 0.5 dB Steps +43 dBm Output IP3 +24.5 dBm Output P1dB 1.5 dB Noise Figure at Max. Gain State Fully Internally Matched Module Integrated Blocking Capacitors, Bias Inductors 3-wire SPI Control Programming General Description Pin Configuration The TQM879006A is a digital variable gain amplifier (DVGA) featuring high linearity over the entire gain control range. The amplifier module features the integration of a low noise amplifier gain block, a digitalstep attenuator (DSA), along with a high linearity 1/4W amplifier. The module has the added features of integrating all matching components with bias chokes and blocking capacitors. The internal DSA offers 0.5 dB step, 6-bit, and 31.5 dB range and is controlled with a TM serial periphery interface (SPI ). The TQM879006A features variable gain from 0 dB to 31.7 dB at 2 GHz, has +43 dBm Output IP3, and +24.5 dBm P1dB. The amplifier also has a very low 1.5 dB Noise Figure (at maximum gain) allowing it to be an ideal DVGA for both receiver and transmitter applications. The amplifier operates from a single +5V supply and is available in a compact 28-pin 6x6 mm leadless SMT package. The TQM879006A is pin compatible with the TQM829007 (0.6-1GHz, 0.25W DVGA) and TQM879008 (1.5-2.7 GHz, 0.5W DVGA). This allows one to size the right type of device for specific system level requirements as well as making the DVGA family ideal for applications where a common PCB layout is used for different frequency bands. Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint Pin No. 1 2 3 4, 22 6 8 14 16 28 All Other Pins Symbol LE DATA CLK NC RFIN VCC_AMP1 VCC_AMP2 RFOUT VCC_SPI GND Ordering Information Part No. Description TQM879006A-PCB Fully Assembled Evaluation Board Includes USB control board (EVH) TQM879006A 1.4-2.7 GHz Digital Variable Gain Amp Standard T/R size = 2500 pieces on a 13" reel. - 1 of 11 - Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Absolute Maximum Ratings Recommended Operating Conditions Parameter Parameter Rating Storage Temperature RF Input Power,CW, 50,T = 25C Vcc (pins 8, 14, 28) Digital Input Voltage -55 to 150 C +23 dBm +5.5 V Vcc+ 0.5V Device Voltage (VCC) Case Temperature 6 Tj for >10 hours MTTF Min +4.75 -40 Typ +5.0 Max Units +5.25 +85 +170 V C C Electrical specifications are measured at specified test conditions. Specifications are not guaranteed over all recommended operating conditions. Operation of this device outside the parameter ranges given above may cause permanent damage. Electrical Specifications Test conditions unless otherwise noted: VCC=+5 V, Temp= +25C, Maximum Gain State Parameter Operational Frequency Range Test Frequency Gain Gain Control Range Conditions Min 1400 0.5 dB Step Size Attenuation Accuracy All States, 3 wire SPI, 6 states Control Interface Input Return Loss Output Return Loss Output P1dB Output IP3 Noise Figure I/O Impedance Supply Voltage Supply Current Thermal Resistance, jc 3-wire serial interface Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint Pout=+11 dBm/tone, f=1 MHz Module (junction to case) - 2 of 11 - Typ Max 2700 2000 27.5 31.7 34 31.5 (0.3+5% of Attenuation setting) Max 6 21 20 +24.5 +38 +43.0 1.5 50 +5 174 215 36.7 Units MHz MHz dB dB dB Bit dB dB dBm dBm dB Ohm V mA C/W Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier J3-20 GND J3-18 Vcc_AM J3-19 P J3-17 J3-16 J3-15 J3-14 J3-13 LE J3-12 J3-11 DATA CLK J3-10 J3-8 J3-9 J3-6 J3-7 J3-5 J3-4 J3-3 J3-2 GND SPI_Vcc J3-1 Application Circuit (TQM879006A-PCB) SPI_LE GND SPI_DATA GND SPI_CLK GND GND GND RF_IN GND GND GND GND GND GND GND 0 J2 RF Output C13 C12 4.7uF C2 0 RF_OUT Vcc_AMP 2 C1 Vcc_AMP1 RF Input GND U1 6X6_ 28PIN NC J1 NC GND GND GND GND SPI_Vcc 0.1uF GND C8 FB1 FB2 0 0 4.7uF Notes: 1. For PCB Board Layout, see page 9 for more information. 2. All Components are of 0603 size unless stated otherwise. 3. For SPI Timing Diagram, see page 6. 4. 0 jumpers may be replaced with copper traces in the target application layout. 5. Different ground pins are used for SPI (digital) and analog supply voltages. 6. The primary RF microstrip characteristic line impedance is 50 . 7. The single power supply is used to provide supply voltage to AMP1 and AMP2. Bill of Material - TQM879006A-PCB Reference Des. Value Description 1.5-2.7 GHz 1/4 W DVGA TriQuint C8 0.1 uF Cap, Chip, 0603, 16V, X7R, 10% various C12, C13 4.7 uF Cap, Chip, 0603, 6.3V, X5R, 20% various Res, Chip, 0603, 1/16W, 5% various U1 n/a C1, C2, FB1, FB2 0 C4 DNP Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint - 3 of 11 - Manuf. Part Number TQM879006A Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Typical Performance , Maximum Gain State Test conditions unless otherwise noted: VCC=+5 V, ICC=174 mA (typ), Temp=+25C Parameter Frequency Gain Input Return Loss 1500 30.8 13 1800 31.4 25 Output Return Loss Output P1dB Output IP3 (11 dBm/tone, f = 1 MHz) Noise Figure 10 +24.1 +40.2 1.35 15 +24.5 +42.0 1.4 Typical Value 2000 31.7 21 2140 31.7 17 2350 31.6 18 2600 30.8 19 20 +24.5 +43.0 1.5 19.5 +24.5 +43.0 1.5 15 +24.4 +41.0 1.6 11 +24.3 +40.5 1.8 Units MHz dB dB dB dBm dBm dB Notes: 1. The evaluation board can be used with TriQuint's USB interface board. Refer to TriQuint's website for more information. Typical Performance Plots S11 vs. Freq over Attenuation States 0 S11 (dB) -5 0dB 0.5dB 1dB 2dB 4dB 8dB 16dB 31.5dB -10 -15 -20 -25 Temp. = 25oC -30 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 Frequency (GHz) Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint - 4 of 11 - Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Typical Performance Plots S22 vs. Freq over Attenuation States 0 Temp. = 25oC S22 (dB) -5 -10 -15 -20 -25 0dB 0.5dB 1dB 2dB 4dB 8dB 16dB 31.5dB -30 1.3 1.5 1.7 1.9 2.1 2.3 2.5 2.7 Frequency (GHz) Attenuation Accuracy vs. Attenuation Attenuation Accuracy (dB) 2.0 Vdd = 5 V , Temp. = 25oC 1.5 1.0 0.5 0.0 -0.5 -1.0 -1.5 1.8GHz 1.9GHz 2.0GHz 2.4GHz 2.7 GHz -2.0 0 Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint - 5 of 11 - 5 10 15 Attenuation (dB) 20 25 30 Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Serial Control Interface Serial Control Timing Characteristics Parameter (Test conditions: VCC = +5 V, TLEAD=25C) Condition Clock Frequency LE Setup Time, tLESUP LE Pulse Width, tLEPW DATA set-up time, tSDSUP DATA hold-time, tSDHLD LE Pulse Spacing tLE Propagation Delay tPLO Min 50% Duty Cycle after last CLK rising edge Parameter 30 Min 0 Input High Voltage, VIH Input Current, IIH / IIL On DATA, LE and CLK DATA (MSB in First 6-Bit Word) Control Logic Truth Table MSB 6-Bit Control Word to DSA Units MHz ns ns ns ns ns ns (Test conditions: VCC = +5 V, TLEAD=25C) Condition Input Low Voltage, VIL 10 10 30 10 10 630 before CLK rising edge after CLK rising edge LE to LE pulse spacing LE to Parallel output valid Serial Control DC Logic Characteristics Max LSB Max 0.8 Units V 2.4 Vcc V -10 +10 A Gain Relative to Maximum Gain D5 D4 D3 D2 D1 D0 Reference : IL 1 1 1 1 1 1 0 dB 1 1 1 1 1 0 0.5 dB 1 1 1 1 0 1 1 dB 1 1 1 0 1 1 2 dB 1 1 0 1 1 1 4 dB 1 0 1 1 1 1 8 dB 0 1 1 1 1 1 16 dB 0 0 0 0 0 0 31.5 dB Any combination of the possible 64 states will provide a reduction in gain of approximately the sum of the bits selected. Serial Control Interface Timing Diagram CLK is disabled when LE is high D5-D0 MSB-LSB D5-D0 MSB-LSB LE tPLO CLK DATA SERIN tSDSUP Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint tLESUP tSDHLD - 6 of 11 - tLEPW Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Detailed Device Description The TQM879006A is a 50 internally matched digital variable gain amplifier (DVGA) featuring high linearity over the entire gain control range. The amplifier module features the integration of a low noise amplifier gain block, a digital step attenuator (DSA), along with a high linearity 1/4W amplifier as shown in the functional diagram below. The module is unconditionally stable. Internal blocking capacitors and bias structures keep external parts count to a minimum. The DVGA has an operational frequency range from 1.4 - 2.7 GHz. Functional Schematic Diagram DC Block DC Block DSA AMP1 Pin 6 DC Block M AMP2 SPI DC Bias Pin 8 DC Block Pin 1 LE Pin 16 M DC Bias Pin 2 Pin 3 DATA CLK Pin 14 Where M = Matching Network. Chain Analysis Table This table provides the typical performance of individual stages in the module as well as overall module performance. Parameter Gain NF OIP3 P1dB Icc Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint AMP1 DSA AMP2 Overall Module Units 85 2.0 87 174 mA 19 1.3 36 20 -1.8 1.8 55 28.5 14.5 4.0 43 24.5 - 7 of 11 - 31.7 1.5 43 24.5 dB dB dBm dBm Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Device Detailed Description AMP1 AMP1 is a wide band low noise amplifier gain block in DVGA module. The amplifier provides 19 dB gain, 1.3 dB noise figure, +36 dBm OIP3 at 2.0 GHz while only drawing 85 mA current. External DC blocks and biasing is not required. AMP1 is DC blocked internally and is connected internally to three bypass capacitors (22 pF, 100 pF, 0.01 uF) followed by 22 nH inductor inside the module as shown in the figure below. Pin 8 0.1 uF 100 pF AMP1 68 nH Pin 6 DC Block DC Block To DSA (internal) DSA (Digital Step Attenuator) TM DVGA has a serial digital step attenuator that is controlled with 6-bit serial periphery interface (SPI ) and has 0.5 dB step size with 31.5 dB attenuation range. This 50-ohm RF DSA maintains high attenuation accuracy over frequency and temperature. "000000" represents maximum attenuation state. External bypass capacitors are needed to compensate the inductance effect associated with long transmission lines on the evaluation board. AMP2 AMP2 is high linearity 1/4-W amplifier in DVGA module. The amplifier provides 14.4 dB gain, +24.5 dBm P1dB, +43 dBm OIP3 at 2.0 GHz while only drawing 87 mA current. The amplifier is optimized over 1.4 - 2.7 GHz bandwidth using internal matching components. AMP2 is DC blocked internally and is connected internally to two bypass capacitors (22 pF, 0.01 uF) followed by an 18 nH inductor inside the module as shown in the figure below. External DC blocks and biasing is not required. Pin 14 0.01 uF 22 pF AMP2 18 nH From DSA (internal) M M DC Block DC Block Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint Pin 16 - 8 of 11 - Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Pin Configuration and Description Pin No. Symbol Description 1 LE Serial Latch Enable Input. When LE is high, latch is clear and content of SPI control the attenuator. When LE is low, data in SPI is latched. 2 DATA Serial data input. The data and clock pins allow the data to be entered serially into SPI and is independent of Latch state. 3 CLK Serial clock input. 4, 22 N/C No internal connection. connect or open. This pin is not connected in this module 6 RFIN Input, matched to 50 ohms between 1800 and 2700 MHz. Internally DC blocked. 8 VCC_AMP1 Supply Voltage to AMP1. This pin is connected internally to 3 bypass capacitors (22pF, 100 pF, 0.01uF) followed by a 22 nH inductor inside the module. 14 VCC_AMP2 Supply Voltage to AMP2. This pin is connected internally to 2 bypass capacitors (22pF, 0.01uF) followed by an 18 nH inductor inside the module. 16 RFOUT Output, matched to 50 ohms between 1800 and 2700 MHz. Internally DC blocked. 28 VCC_SPI Supply voltage for SPI and DSA chip. This pin is connected to 0.1uF bypass capacitor internally. All other Pins GND RF/DC Ground Connection Evaluation Board PCB Information TriQuint PCB 1080956 Material and Stack-up 50 ohm line dimensions: width = .030", spacing = .036" Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint - 9 of 11 - Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Package Marking and Dimensions Marking: Part number - TQM879006A Lot Code - YYWW CCCC Vendor Code and Triquint Lot Number - AaXXXX TQM879006A Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. Except where noted, this part outline conforms to JEDEC standard MO-220, Issue E (Variation VGGC) for thermally enhanced plastic very thin fine pitch quad flat no lead package (QFN). 3. Dimension and tolerance formats conform to ASME Y14.4M-1994. 4. The terminal #1 identifier and terminal numbering conform to JESD 95-1 SPP-012. PCB Mounting Pattern Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. Use 1 oz. copper minimum for top and bottom layer metal. 3. Vias are required under the backside paddle of this device for proper RF/DC grounding and thermal dissipation. We recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10"). 4. Ensure good package backside paddle solder attach for reliable operation and best electrical performance. Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint - 10 of 11 - Disclaimer: Subject to change without notice www.triquint.com TQM879006A 1.4 -2.7 GHz 1/4 W Digital Variable Amplifier Product Compliance Information ESD Sensitivity Ratings Solderability Compatible with both lead-free (260C maximum reflow temperature) and tin/lead (245C maximum reflow temperature) soldering processes. Caution! ESD-Sensitive Device Contact plating: Electrolytic Plated Au over Ni ESD Rating: Value: Test: Standard: Class 1A Passes 250 V to < 500 V Human Body Model (HBM) JEDEC Standard JESD22-A114 ESD Rating: Value: Test: Standard: Class IV Passes 1000 V Charged Device Model (CDM) JEDEC Standard JESD22-C101 RoHs Compliance This part is compliant with EU 2002/95/EC RoHS directive (Restrictions on the Use of Certain Hazardous Substances in Electrical and Electronic Equipment). MSL Rating MSL Rating: Level 3 Test: 260C convection reflow Standard: JEDEC Standard IPC/JEDEC J-STD-020 This product also has the following attributes: * Halogen Free (Chlorine, Bromine) * Antimony Free * TBBP-A (C15H12Br402) Free * PFOS Free * SVHC Free Contact Information For the latest specifications, additional product information, worldwide sales and distribution locations, and information about TriQuint: Web: www.triquint.com Email: info-sales@triquint.com Tel: Fax: +1.503.615.9000 +1.503.615.8902 For technical questions and application information: Email: sjcapplications.engineering@triquint.com Important Notice The information contained herein is believed to be reliable. TriQuint makes no warranties regarding the information contained herein. TriQuint assumes no responsibility or liability whatsoever for any of the information contained herein. TriQuint assumes no responsibility or liability whatsoever for the use of the information contained herein. The information contained herein is provided "AS IS, WHERE IS" and with all faults, and the entire risk associated with such information is entirely with the user. All information contained herein is subject to change without notice. Customers should obtain and verify the latest relevant information before placing orders for TriQuint products. The information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. TriQuint products are not warranted or authorized for use as critical components in medical, life-saving, or lifesustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death. Datasheet: Rev Q 04-23-13 (c) 2013 TriQuint - 11 of 11 - Disclaimer: Subject to change without notice www.triquint.com