DATA SHEET PHOTOCOUPLER PS9817A-1,-2 HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE 8-PIN SSOP (SO-8) -NEPOC HIGH-SPEED PHOTOCOUPLER Series- DESCRIPTION The PS9817A-1 and PS9817A-2 are active-low type high-speed photocouplers that use a GaAlAs light-emitting diode on the input side and a photodetector IC that includes a photodiode and a signal processor on the same chip on the output side. The PS9817A-1 and PS9817A-2 are designed specifically for high common mode transient immunity (CMR) and low pulse width distortion. The PS9817A-2 is suitable for high density applications. FEATURES PIN CONNECTION * Pulse width distortion (tPHL-tPLH = 35 ns MAX.) (Top View) * High common mode transient immunity (CMH, CML = 15 kV/s MIN.) 8 7 1 2 PS9817A-1 6 5 1. NC 2. Anode 3. Cathode 4. NC 5. GND 6. VO 7. NC 8. VCC 3 4 * High-speed (10 Mbps) * High isolation voltage (BV = 2 500 Vr.m.s.) * Open collector output * Ordering number of tape product : PS9817A-1-F3: 1 500 pcs/reel : PS9817A-2-F3: 1 500 pcs/reel * Pb-Free product * Safety standards * UL approved: File No. E72422 8 7 1 2 SHIELD * DIN EN60747-5-2 (VDE0884 Part2) approved: No. 40008347 (Option) APPLICATIONS * Measurement equipment * PDP PS9817A-2 6 5 1. Anode1 2. Cathode1 3. Cathode2 4. Anode2 5. GND 6. VO2 7. VO1 8. VCC 3 4 SHIELD * 40% reduction of mounting area (5-pin SOP x 2) * FA Network TRUTH TABLE LED Output ON L OFF H The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. Document No. PN10647EJ03V0DS (3rd edition) Date Published August 2008 NS Printed in Japan The mark shows major revised points. The revised points can be easily searched by copying an "" in the PDF file and specifying it in the "Find what:" field. 2006, 2008 PS9817A-1,-2 PACKAGE DIMENSIONS (UNIT: mm) 5.210.25 8 5 1 4 0.10.1 0.15 +0.10 -0.05 3.270.2 6.00.2 2 3.950.1 1.27 0.4 +0.10 -0.05 0.50.3 0.10 S 0.25 M Data Sheet PN10647EJ03V0DS PS9817A-1,-2 MARKING EXAMPLE SnBi PLATING PS9817A-1 9817A-1 NL831 PS9817A-2 9817A-2 NL831 Type Number Assembly Lot Type Number Assembly Lot N N N L 8 31 N L 8 31 Week Assembled Year Assembled (Last 1 Digit) No. 1 pin Mark Initial of NEC (Engraved mark) Week Assembled Year Assembled (Last 1 Digit) No. 1 pin Mark Initial of NEC (Engraved mark) In-house Code (L: Pb-Free) In-house Code (L: Pb-Free) Rank Code Rank Code PS9817A-1 PS9817A-2 Ni/Pd/Au PLATING 9817A-1 NT831 9817A-2 NT831 Type Number Assembly Lot Assembly Lot N N N T 8 31 No. 1 pin Mark Initial of NEC (Engraved mark) Type Number N T 8 31 Week Assembled Year Assembled (Last 1 Digit) No. 1 pin Mark Initial of NEC (Engraved mark) In-house Code (T: Pb-Free) Week Assembled Year Assembled (Last 1 Digit) In-house Code (T: Pb-Free) Rank Code Rank Code Data Sheet PN10647EJ03V0DS 3 PS9817A-1,-2 ORDERING INFORMATION Part Number Order Number Solder plating Packing Style Safety Standards Application Part Approval Number specification PS9817A-1 PS9817A-1-A Pb-Free 20 pcs (Tape 20 pcs cut) Standard products PS9817A-1-F3 PS9817A-1-F3-A (SnBi) Embossed Tape 1 500 pcs/reel (UL approved) PS9817A-2 PS9817A-2-A 20 pcs (Tape 20 pcs cut) PS9817A-2-F3 PS9817A-2-F3-A Embossed Tape 1 500 pcs/reel PS9817A-1-V PS9817A-1-V-A 20 pcs (Tape 20 pcs cut) DIN EN60747-5-2 PS9817A-1-V-F3 PS9817A-1-V-F3-A Embossed Tape 1 500 pcs/reel (VDE0884 Part2) PS9817A-2-V PS9817A-2-V-A 20 pcs (Tape 20 pcs cut) approved PS9817A-2-V-F3 PS9817A-2-V-F3-A Embossed Tape 1 500 pcs/reel (Option) PS9817A-1 PS9817A-1-AX Pb-Free 20 pcs (Tape 20 pcs cut) Standard products PS9817A-1-F3 PS9817A-1-F3-AX (Ni/Pd/Au) Embossed Tape 1 500 pcs/reel (UL approved) PS9817A-2 PS9817A-2-AX 20 pcs (Tape 20 pcs cut) PS9817A-2-F3 PS9817A-2-F3-AX Embossed Tape 1 500 pcs/reel PS9817A-1-V PS9817A-1-V-AX 20 pcs (Tape 20 pcs cut) DIN EN60747-5-2 PS9817A-1-V-F3 PS9817A-1-V-F3-AX Embossed Tape 1 500 pcs/reel (VDE0884 Part2) PS9817A-2-V PS9817A-2-V-AX 20 pcs (Tape 20 pcs cut) approved PS9817A-2-V-F3 PS9817A-2-V-F3-AX Embossed Tape 1 500 pcs/reel (Option) Data Sheet PN10647EJ03V0DS PS9817A-1 PS9817A-2 PS9817A-1 PS9817A-2 PS9817A-1 PS9817A-2 *1 For the application of the Safety Standard, following part number should be used. 4 *1 PS9817A-1 PS9817A-2 PS9817A-1,-2 ABSOLUTE MAXIMUM RATINGS (TA = 25C, unless otherwise specified) Parameter Symbol Ratings PS9817A-1 Diode PS9817A-2 *1 IF Reverse Voltage VR 5 V/ch Supply Voltage VCC 7 V Output Voltage VO 7 V/ch IO 25 mA/ch PC 40 mW/ch BV 2 500 Vr.m.s. Operating Ambient Temperature TA -40 to +85 C Storage Temperature Tstg -55 to +125 C Output Current Power Dissipation Isolation Voltage *3 *4 15 *2 Forward Current Detector 20 Unit mA/ch *1 Reduced to 0.3 mA/C at TA = 60C or more. *2 Reduced to 0.1 mA/C at TA = 60C or more. *3 Applies to output pin VO (collector pin). Reduced to 1.5 mW/C at TA = 65C or more. *4 AC voltage for 1 minute at TA = 25C, RH = 60% between input and output. Pins 1-4 shorted together, 5-8 shorted together. RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. Low Level Input Voltage VFL 0 High Level Input Current IFH 6.3 Supply Voltage VCC Pull-up Resistance RL TLL (RL = 1.0 k, loads) N TYP. MAX. Unit 0.8 V 12.5 mA 4.5 5.5 V 330 4k 10 5 Data Sheet PN10647EJ03V0DS 5 PS9817A-1,-2 ELECTRICAL CHARACTERISTICS (TA = -40 to +85C, unless otherwise specified) Parameter Diode Detector Symbol Conditions MIN. Unit 1.8 V 10 A IF = 10 mA, TA = 25C Reverse Current IR VR = 3.0 V, TA = 25C Terminal Capacitance Ct VF = 0 V, f = 1 MHz, TA = 25C 30 IOH VCC = VO = 5.5 V, VF = 0.8 V 1 100 A VOL VCC = 5.5 V, IF = 5.0 mA, IOL = 13 mA 0.2 0.6 V ICCH VCC = 5.5 V, IF = 0 mA, VO = open 4 7 mA 8 14 6 10 12 20 2 5 *2 High Level Supply Current (PS9817A-1) High Level Supply Current (PS9817A-2) Low Level Supply Current (PS9817A-1) ICCL VCC = 5.5 V, IF = 10 mA, VO = open Low Level Supply Current (PS9817A-2) 1.65 MAX. VF Low Level Output Voltage Coupled *1 Forward Voltage High Level Output Current 1.4 TYP. pF Threshold Input Current (H L) IFHL VCC = 5.0 V, VO = 0.8 V, RL = 350 Isolation Resistance RI-O VI-O = 1 kVDC, RH = 40 to 60%, TA = 25C 10 11 Insulation Resistance (Input-Input), (PS9817A-2) RI-I VI-I = 1 kVDC, RH = 40 to 60%, TA = 25C 10 10 Isolation Capacitance CI-O V = 0 V, f = 1 MHz, TA = 25C 0.6 pF Insulation Capacitance (Input-Input), (PS9817A-2) CI-I V = 0 V, f = 1 MHz, TA = 25C 0.3 pF Propagation Delay Time tPHL TA = 25C 40 (H L) *3 tPLH TA = 25C 45 *3 tr Fall Time Propagation Delay Skew Common Mode Transient Immunity at High *4 Level Output Common Mode Transient Immunity at Low *4 Level Output ns 75 100 Rise Time Pulse Width Distortion (PWD) 75 100 Propagation Delay Time (L H) mA *3 VCC = 5.0 V, RL = 350 , IF = 7.5 mA 20 tf 5 tPHL-tPLH 5 tPSK 35 40 CMH VCC = 5.0 V, RL = 350 , TA = 25C, IF = 0 mA, VO > 2 V, VCM = 1 kV 15 20 CML VCC = 5.0 V, RL = 350 , TA = 25C, IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV 15 20 kV/s *1 Typical values at TA = 25C *2 Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. 6 Data Sheet PN10647EJ03V0DS PS9817A-1,-2 *3 Test circuit for propagation delay time VCC = 5 V PS9817A-1 (PW = 1s, Pulse input (IF) Duty cycle = 1/10) 0.1 F RL = 350 VO (Monitor) CL = 15 pF Input (Monitor) (IF = 7.5 mA) 50% Input 47 Output VCC = 5 V PS9817A-2 (PW = 1s, Pulse input (IF) Duty cycle = 1/10) RL = 350 VO (Monitor) Input (Monitor) SHIELD tPHL 1.5 V VOL tPLH 0.1 F CL = 15 pF 47 SHIELD Remark CL includes probe and stray wiring capacitance. *4 Test circuit for common mode transient immunity PS9817A-1 SW IF VCC = 5 V 0.1 F RL = 350 VO (Monitor) CL = 15 pF 1 kV VCM 90% 10% VCM 0V tr VO (IF = 0 mA) PS9817A-2 SW IF VCC = 5 V RL = 350 SHIELD 0.1 F VO (Monitor) CL = 15 pF VO (IF = 7.5 mA) tf VOH 2V 0.8 V VOL SHIELD VCM USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 F is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity. Data Sheet PN10647EJ03V0DS 7 PS9817A-1,-2 TYPICAL CHARACTERISTICS (TA = 25C, unless otherwise specified) DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 50 Detector Power Dissipation PC (mW) Maximum Forward Current IF (mA) 30 25 20 15 PS9817A-1 PS9817A-2 10 5 0 20 40 80 85 60 100 10 40 80 85 60 FORWARD CURRENT vs. FORWARD VOLTAGE SUPPLY CURRENT vs. AMBIENT TEMPERATURE 100 20 10 TA = +85C +50C +25C 0C -25C 1 0.1 1.2 1.4 1.6 1.8 2.0 2.2 16 14 10 ICCH (IF = 0 mA), PS9817A-2 8 6 ICCL (IF = 10 mA), PS9817A-1 4 ICCH (IF = 0 mA), PS9817A-1 2 -25 0 25 50 75 100 Ambient Temperature TA (C) OUTPUT VOLTAGE vs. FORWARD CURRENT LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE 0.6 Low Level Output Voltage VOL (V) RL = 350 1.0 k 4 4.0 k, 4.7 k 3 2 1 1 2 3 4 5 6 IF = 5.0 mA, VCC = 5.5 V 0.5 0.4 IOL = 16.0 mA 13.0 mA 10.0 mA 6.0 mA 0.3 0.2 0.1 0 -50 -25 0 25 50 75 Ambient Temperature TA (C) Forward Current IF (mA) Remark ICCL (IF = 10 mA), PS9817A-2 12 Forward Voltage VF (V) 5 0 18 0 -50 2.4 VCC = 5.0 V 8 20 Ambient Temperature TA (C) High Level Supply Current ICCH (mA) Low Level Supply Current ICCL (mA) Forward Current IF (mA) 20 Ambient Temperature TA (C) 6 Output Voltage VO (V) 30 0 100 0.01 1.0 40 The graphs indicate nominal characteristics. Data Sheet PN10647EJ03V0DS 100 PS9817A-1,-2 PROPAGATION DELAY TIME vs. AMBIENT TEMPERATURE THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE Propagation Delay Time tPHL, tPLH (ns) VCC = 5.0 V, VO = 0.6 V 4 RL = 350 3 1.0 k 2 4.0 k 1 0 -50 -25 0 25 50 75 Pulse Width Distortion tPHL-tPLH (ns) 80 tPLH: RL = 4.7 k 60 tPLH: RL = 4.0 k tPLH: RL = 1.0 k 40 20 -25 0 25 50 75 PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE PROPAGATION DELAY TIME vs. FORWARD CURRENT RL = 4.7 k 40 30 RL = 4.0 k 20 RL = 1.0 k 10 RL = 350 -25 0 25 50 75 100 100 100 VCC = 5.0 V tPLH: RL = 4.7 k 80 60 tPLH: RL = 1.0 k tPLH: RL = 4.0 k 40 tPLH: RL = 350 20 0 5 Ambient Temperature TA (C) Remark tPLH: RL = 350 tPHL: RL = 350 , 1.0 k, 4.0 k, 4.7 k Ambient Temperature TA (C) IF = 7.5 mA, VCC = 5.0 V 0 -50 IF = 7.5 mA, VCC = 5.0 V Ambient Temperature TA (C) 60 50 100 0 -50 100 Propagation Delay Time tPHL, tPLH (ns) Threshold Input Current IFHL (mA) 5 tPHL: RL = 350 , 1.0 k, 4.0 k, 4.7 k 7 9 11 13 15 Forward Current IF (mA) The graphs indicate nominal characteristics. Data Sheet PN10647EJ03V0DS 9 PS9817A-1,-2 TAPING SPECIFICATIONS (UNIT: mm) 1.70.1 5.560.1 5.50.1 1.5+0.1 -0 12.00.2 2.00.05 4.00.1 1.750.1 Outline and Dimensions (Tape) 4.05 MAX. 3.60.1 6.40.1 0.30.05 8.00.1 Taping Direction PS9817A-1-F3 PS9817A-2-F3 Outline and Dimensions (Reel) 2.00.5 13.00.2 21.00.8 1001.0 R 1.0 3302.0 2.00.5 13.00.2 13.51.0 17.51.0 11.9 to 15.4 Outer edge of flange Packing: 1 500 pcs/reel 10 Data Sheet PN10647EJ03V0DS PS9817A-1,-2 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) 1.27 0.8 1.45 5.25 Data Sheet PN10647EJ03V0DS 11 PS9817A-1,-2 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering * Peak reflow temperature 260C or below (package surface temperature) * Time of peak reflow temperature 10 seconds or less * Time of temperature higher than 220C 60 seconds or less * Time to preheat temperature from 120 to 180C 12030 s * Number of reflows Three * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Package Surface Temperature T (C) Recommended Temperature Profile of Infrared Reflow (heating) to 10 s 260C MAX. 220C to 60 s 180C 120C 12030 s (preheating) Time (s) (2) Wave soldering * Temperature 260C or below (molten solder temperature) * Time 10 seconds or less * Preheating conditions 120C or below (package surface temperature) * Number of times One (Allowed to be dipped in solder including plastic mold portion.) * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron * Peak Temperature (lead part temperature) 350C or below * Time (each pins) 3 seconds or less * Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100C 12 Data Sheet PN10647EJ03V0DS PS9817A-1,-2 (4) Cautions * Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler's input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. Data Sheet PN10647EJ03V0DS 13 PS9817A-1,-2 SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Symbol Speck Unit Application classification (DIN EN 60664-1 VDE0110 Part 1) for rated line voltages 300 Vr.m.s. IV for rated line voltages 600 Vr.m.s. III Climatic test class (DIN EN 60664-1 VDE0110) 40/85/21 Dielectric strength maximum operating isolation voltage Test voltage (partial discharge test, procedure a for type test and random test) UIORM 566 Vpeak Upr 849 Vpeak Upr 1 061 Vpeak UTR 4 000 Vpeak Upr = 1.5 x UIORM, Pd < 5 pC Test voltage (partial discharge test, procedure b for all devices) Upr = 1.875 x UIORM, Pd < 5 pC Highest permissible overvoltage Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) 2 Clearance distance >4.0 mm Creepage distance >4.0 mm Comparative tracking index (DIN IEC 112/VDE 0303 Part 1) CTI Material group (DIN EN 60664-1 VDE0110 Part 1) 175 III a Storage temperature range Tstg -55 to +125 C Operating temperature range TA -40 to +85 C VIO = 500 V dc at TA = 25C Ris MIN. 10 12 VIO = 500 V dc at TA MAX. at least 100C Ris MIN. 10 11 Package temperature Tsi 150 C Current (input current IF, Psi = 0) Isi 150 mA Power (output or total power dissipation) Psi 600 mW Ris MIN. 10 Isolation resistance, minimum value Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Isolation resistance VIO = 500 V dc at TA = Tsi 14 Data Sheet PN10647EJ03V0DS 9 PS9817A-1,-2 * The information in this document is current as of August, 2008. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC Electronics data sheets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not all products and/or types are available in every country. Please check with an NEC Electronics sales representative for availability and additional information. * No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may appear in this document. * NEC Electronics does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC Electronics products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Electronics or others. * Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of a customer's equipment shall be done under the full responsibility of the customer. NEC Electronics assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. * While NEC Electronics endeavors to enhance the quality, reliability and safety of NEC Electronics products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC Electronics products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. * NEC Electronics products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC Electronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC Electronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC Electronics product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC Electronics products is "Standard" unless otherwise expressly specified in NEC Electronics data sheets or data books, etc. If customers wish to use NEC Electronics products in applications not intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to determine NEC Electronics' willingness to support a given application. (Note) (1) "NEC Electronics" as used in this statement means NEC Electronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or manufactured by or for NEC Electronics (as defined above). M8E 02. 11-1 Data Sheet PN10647EJ03V0DS 15 PS9817A-1,-2 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. * Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. * Do not burn, destroy, cut, crush, or chemically dissolve the product. * Do not lick the product or in any way allow it to enter the mouth. To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the old company name remains in this document, it is a valid Renesas Electronics document. We appreciate your understanding. Renesas Electronics website: http://www.renesas.com April 1st, 2010 Renesas Electronics Corporation Issued by: Renesas Electronics Corporation (http://www.renesas.com) Send any inquiries to http://www.renesas.com/inquiry. Notice 1. 2. 3. 4. 5. 6. 7. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. Renesas Electronics products are classified according to the following three quality grades: "Standard", "High Quality", and "Specific". The recommended applications for each Renesas Electronics product depends on the product's quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as "Specific" without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as "Specific" or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is "Standard" unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. "Standard": 8. 9. 10. 11. 12. Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support. "Specific": Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majorityowned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.