1
Lightweight SMT Miniature Coaxial Connectors – 1.4 mm Mated Height
N.FL Series
2014.10w
■Features
1.
Low profile
Nominal mated height is 1.4 mm (Max. 1.5 mm)
2. Small size: 7.7 mm2
3. Light weight
Receptacle : 14 mg
Plug : 28 mg
4. Accepts high frequency transmission
of DC to 6 GHz.
V.S.W.R. = 1.3 max. (DC to 6 GHz)
5.
Board placement with automatic equipment
Receptacles are packaged in embossed carrier
tape and reel for automatic mounting.
6.
Plugs are terminated with ultra-fine
coaxial (fluorinated resin insulated) cable.
7. Special tool for an extraction
8.
Verification of the fully mated condition
Tactile click sensation confirms fully mated
condition, assuring complete electrical and
mechanical connection.
9.
Halogen-free*(Receptacle, plug(HF type))
*As defined by IEC61249-2-21
Br-900 ppm maximum, Cl-900 ppm maximum,
Cl+Br combined - 1,500 ppm maximum
■Applications
Mobile phones, wireless communication devices,
electronic measuring instruments, GPS, wireless
LAN, Bluetooth and any application requiring high
frequency transmission using small coaxial
connectors.
3.4
Dia.0.81
N.FL-LP-040*
Cable
N.FL-R-SMT-1
1.4(1.5MAX)
Plug
Receptacle
1.4(1.5MAX)
1.9(2.0MAX)
N.FL U.FL-LP(V)
● Mated height comparison (With U.FL-LP(V) )
● N.FL Plug and Receptacle
Fig.1
Fig.2
2
N.FL Series●Lightweight SMT Miniature Coaxial Connectors – 1.4 mm Mated Height
■Specifications
Nominal characteristic impedance
Frequency range
50 ohms
DC to 6 GHz
Operating temperature range
Storage temperature range
-40°C to +90°C
(90% RH max.)
-30°C to +70°C
(90% RH max.)
Ratings
Note1: N.FL Cable assembly (plug) is measured with SMA conversion
adapters mated with N.FL plugs at both ends of a 100cm coaxial
cable harness
Note2: N.FL receptacle, which is mounted on a 50 ohms glass epoxy
board, is measured with a SMA conversion adapter.
Network Analyzer
Test Set
Test Port
TerminationD.U.T
Test Port Cable
■Materials / Finishes
●
Plugs-Right Angle
Part Material Finish
Shell Phosphor bronze Silver plated
Female center contact Phosphor bronze Gold plated
Insulator PBT Color: Black, UL94V-0
Color: Gray, UL94HB(HF type)
●
Receptacle
Part Material Finish
Shell Phosphor bronze Silver plated
Male center contact Brass Gold plated
Insulator LCP Color: Black, UL94V-0
Item Specification Conditions
1. Contact resistance Center contact: 25 m ohms max.
Outer contact: 25 m ohms max. 10 mA max.
2. Insulation resistance 500 M ohms min. 100V DC
3. Withstanding voltage No flashover or insulation breakdown 200V AC / 1 minute
4. V.S.W.R.(Note) 1.3max. DC to 6GHz
5. Durability
Contact resistance Center contact: 30 m ohms max.
Outer contact: 30 m ohms max.
No damage, cracks, or parts dislocation
20 cycles
6. Vibration No electrical discontinuity of 1 µs or longer
No damage, cracks, or parts dislocation
Frequency: 10 to 100 Hz, single amplitude of 1.5 mm
Acceleration: 59 m/s2, in each of 3 axis
5 cycles
7. Shock No electrical discontinuity of 1 µs or longer
No damage, cracks, or parts dislocation
Acceleration of 735 m/s2, 11 ms continuous time
Waveform: sine half-wave, 3 cycles in each of the 3 axis
8. Humidity
Insulation resistance: 100 M ohms min. (high humidity)
Insulation resistance: 500 M ohms min. (dry)
No damage, cracks, or parts dislocation
96 hours at +40°C, and humidity of 95%
9. Temperature cycle No damage, cracks, or parts dislocation
Temperature:-40°C/+5°C to +35°C/+90°C/+5°C to +35°C
Time: 30 min./ 5 min. max. / 30 min. / 5 min. max.
5 cycles
10. Salt spray test No excessive corrosion 5% salt water solution, 48 hours
Note: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and
specifications for a specific part number shown.
* V.S.W.R. Measurement System
Measured as shown on the block diagram below.
3
N.FL Series●Lightweight SMT Miniature Coaxial Connectors – 1.4 mm Mated Height
How To Specify Cable Assembly
Ordering Information
Standard tolerances for (L)
■Cable Assembly(Plug)
N.FL -2LP HF6 -04N
「」
TV -A - L
[Double-ended cable assembly] [Single-ended cable assembly]
Ordering Information
Series name N.FL
Assembly type LP : Single ended
2LP : Double ended
Environmental compliant
HF6 : Halogen-free plug
6 : Standard Plug
Cable type 04N : 0.81mm dia. ultra-time coaxial cable
Cable color 1:White 2:Black
Cable outer conductor TV: Tin plated braided wire
Total length (mm) Length(L)
(L)mm Standard Tolerance(mm)
*L=35 to 200 ±4
*L=200 to 500 ±8
*L=500 to 1000 ±12
L=Longer than 1000 ±1.5% of (L)
2.8
3.4
1.12
Note: Minimum available length(L) is 35mm.
LL
N.FL-LP-040(06), N.FL-LP-040HF(06)(Applicable cable: outer diameter 0.81)
[Plugs can be ordered only as terminated cable assemblies]
Used Plug: N.FL-LP-040(06), N.FL-LP-040HF(06)
Double-
Ended
Single-
Ended N.FL - LP HF6 -04N
「」
TV -A
- L
Ordering Information
❶
❶
❶
❷
❸
❹
❺
❻
❼
❷
❷
❸
❸
❹
❹
❺
❺
❻
❻
❼
❼
L(mm) L(mm)
4
N.FL Series●Lightweight SMT Miniature Coaxial Connectors – 1.4 mm Mated Heightproduct)
■Receptacle
B
Recommended PCB
mounting pattern
GND
GND
GND
SIG
Ø2
0.6
1.8
2.6
3.1
0.6
2.6
3
0.25
0.8
No conductive
traces in this area GND
SIG
0.8
1.9
3.8
1.85
2
2.05
All dimensions: mm
All dimensions: mm
Part No. HRS No. Packaging RoHS
N.FL-R-SMT-1(60) 331-0332-3 60 Reel (5,000 pcs/reel)
N.FL-R-SMT-1(80) 331-0332-3 80 Reel (10,000 pcs/reel)
●Embossed Carrier Tape Dimensions (IEC 60286-3 compliant)
12
8
1.755.5
2 4
Ø
1.5
Unreeling direction
Embossed Carrier tape Dimensions Reel Dimensions
12
5.5 1.75
2 4
4
Ø
1.5
Unreeling direction
2
Ø330
13.5
Ø13
Ø21
A
Material：PS(Black)
A（SCALE FREE）
(N.FL-R-SMT-1(60) 8mm pitch)
(N.FL-R-SMT-1(80) 4mm pitch)
5
N.FL Series●Lightweight SMT Miniature Coaxial Connectors – 1.4 mm Mated Heightproduct)
This jig is used for extraction from a mating condition.
U. FL/
90
50
3
2.1
Ø15
All dimensions: mm
●SMA Conversion Adapter
Note: When mating with corresponding part (N.FL-R-
SMT-1) must be pressed down and held to make
complete connection.
Part No.
HRMJ-N.FLP-ST5
HRS No. RoHS
311-0423-2
All dimensions: mm
(18.3)
Ø6.35
5.5
6
1/4-36UNS-2A
(4)
Note: Applicable to all the U.FL-LP(V)-040, U.FL-LP-062 and N.FL.
Part No.
U.FL-LP(V)-N-2
RoHS
HRS No.
331-0493-2
Plug extraction tool
Note: Applicable to both N.FL and U.FL.
Part No.
HRMJ-U.FLP(40)
HRS No. RoHS
311-0301-5 40
All dimensions: mm
● SMA Conversion Adapter (N.FL / U.FL side plug - SMA side jack)
Note:
The FL side mating portions has a lower lock retention
force than the regular product, therefore, cannot be used
for purposes other than performance measurements.
14.05
Ø6.35
1/4-36UNS-2A
65.6(4.05)
■Conversion Adapters
Part No.
HRMP-U.FLJ(40)
HRS No. RoHS
311-0300-2 40
All dimensions: mm
● SMA Conversion Adapter (N.FL / U.FL side jack - SMA side plug)
Note:
The FL side mating portions has a lower lock retention
force than the regular product, therefore, cannot be used
for purposes other than performance measurements.
(10.7) 8HEX
Note: Applicable to both N.FL and U.FL.
■Receptacle Inspection Adapter
Part No.
U.FL-R-1
HRS No. RoHS
331-0466-0
All dimensions: mm
Used for inspecting the performance
parameters of the cable assembly.
12.9
57HEX
M5∞0.5
1
(7.9)
(4.4)
(12.9)
JAPAN
For distinction with
W.FL-LP-IN.
8 Ø10
All dimensions: mm
Part No.
U.FL-LP-IN
RoHS
HRS No.
331-0334-9
This tool is used for mating a plug.
Plug mating tool
Note: Applicable to both N.FL and U.FL.
6
N.FL Series●Lightweight SMT Miniature Coaxial Connectors – 1.4 mm Mated Height
1. Plug
■Usage Precautions
U.FL-LP(V)-N-2
Extraction tool N.FL-LP-040
Plug
N.FL-R-SMT-1
Receptacle
(1) Mating / unmating
(2) Pull forces on the
cable after connectors
are mated
(3) Precautions
• Unmating Insert the end of an extraction tool into a space between a plug and receptacle, and pull up
the tool in the perpendicular to a mounting surface of a receptacle, as shown in the figure.
● Recomended the use of the extraction tool for unmating.
Any attempt of unmating by pulling on the cable may
result in damage to the mechanical / electrical performance.
• Mating Do not attempt to insert on an extreme angle.
Do not twist connectors excessively during mating / unmating.
N.FL-LP-040
Plug 2.9N max.
N.FL-R-SMT-1
Receptacle
Do not apply any pull forces after the bending
of the cable.
2. Receptacle
(1) Recommended reflow
temperature profile
q
The temperature profile indicates the board surface temperature at the point of contacts with the connector
leads.
w In individual applications the actual temperature may vary, depending on the solder paste type, volume /
thickness and board size / thickness. Consult your solder paste and equipment manufacturer for the
detailed recommendations.
Soldering iron temperature: 350°C, Soldering time: for 5 seconds max.(2) Manual soldering
(3) Recommended metal
mask thickness 0.1 mm to 0.12 mm
(4) Reflow cycles 2 times
80
100
120
140
160
180
200
220
240
260
[ç]
Preheat
(130 to 180ç)
230ç
220ç
50 seconds max.120 seconds max.
60 seconds max.
Time
250 ç max. for
10 seconds
(1) Operating environment
The connectors are not designed to operate in the following environments:
• Exposed to a excessive amounts of fine particles and dust
• Regions and places having a high density of sulfur dioxide, hydrogen sulfide, nitrogen dioxide or other corrosive
gasses.
• Environments having large rapid variations in temperature.
(2) Storage conditions -
Receptacle
Store in the Hirose Electric packaging.
Temperature: -10 to +40ç, Humidity: 85% max.
Use within 6 months of delivery.
Receptacles for which the storage period has elapsed must be tested for solderability to the PC board
mounting surface.
3. Operating environment and storage conditions
The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use.
The contents of this catalog are current as of date of 10/2014. Contents are subject to change without notice for the purpose of improvements.
2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN
TEL: +81-45-620-3526 Fax: +81-45-591-3726
http://www.hirose.com
http://www.hirose-connectors.com
®
