.100 x .100 Latch/Ejector Header 3 Wall, Straight & Right Angle, High Temp Option 76 Military (with 3Ms 3518 polarizing key ) and center bump polarization Low profile Optional ejector latches Mounting holes for securing header to board Three wall shroud provides design flexibility Solder tail and wrap tail options Optional polarizing posts available Choice of rolled pin and snap-in latches High temperature option Date Issued: February 19, 1999 TS-0771-01 Sheet 1 of 4 Physical Insulation Material: Flammability: Color: Marking: Contact Material: Plating Underplate: Wiping Area: Solder Tails: Wrap Tails: Glass Filled Polyester (PBT) Glass Filled Polyester (PCT High Temp Option) UL 94V-0 Gray Beige (High Temp Option) 3M Logo, Part Identification Number and Orientation Triangle Copper Alloy 100 w [ 2.54 ym ] Nickel QQ-N-290, Class 2 Gold MIL-G-45204, Type II, Grade C 200 1 [ 5.08 um ] 60/40 Tin Lead - MIL-P-81728 Gold Flash Electrical Current Rating: Insulation Resistance: Withstanding Voltage: 1A >1 x 109 Q at 500 Vde 1000 Vrms at Sea Level Environmental Temperature Rating: UL File No.: E68080 ~55C to +105C 3M Electronic Products Division 6801 River Place Blvd. Austin, TX 78726-9000 For technical, sales or ordering information call 800-225-5373 .100 .100 Latch/Ejector Header 3 Wall, Straight & Right Angle, High Temp Option -XOXX Header with No Ejector/Latch a" -X2XX -XBXX -X5XX -X6XX Header with Header with Short Ejector/Latch Long Ejector/Latch for 3M Sockets without for 3M. Sockets with Strain Relief Strain Retief MAXX Header with Ejector only 42 Ref (10.7} Note: This Ejector is a Nickel Plated Zinc Alloy Casting. 7.2) Ret _i 025 + .002 Sq Typ ~~ [0.64] 2X @.100 [2.54] 15 (See Note 2) 1) r .24 (3.8) L D } 28 L 16.1] 020 [7.1] y eon | SAD g Qt a oro uo Wi toe X oc aT Ha AS | oo oo aang oo | 30 i738) LSP ; - oo aaoa oD @ T 1 Ea t == __f ~ neal 100 Ret _ [2.54] es L E+.010 42 - {3.0} - Position 1 | B yn Notch A a F Typ Position 1 (See Tabie 1 & Note1) . Orientation ' Notch B Section AA Triangle | (Gee lable 1) Notch C .025 + .002 Sq Typ | 241 16 | (See Table 1 & Note 1) [0.64 } {5.3} {4.1] | A ~ B 100 Ret [Tq | | (2.54) HL | al [6.1] 68 H fF 73) LL , _\ _|O oat 35 oN -v-- 30 39 to 78) | | [ eM \ \\ | J / | ! | re renin Es 010 (ost / vue yo DF .197 049 Ref | | ss [1.24] A C [5.00] 20 2X @ .100 . Section B-B [2.54] A (Right Angle) (See Note 2) TS-0771-01 Sheet 2 of 4 3M Electronic Products Division 6801 River Place Blvd. Austin, TX 78726-9000 For technical, sales or ordering information call 800-225-5373 .100 x .100 Latch/Ejector Header 3 Wall, Straight & Right Angle, High Temp Option Tabie 1 Pin 3M Part Dimensions Poharization Quantity Number A B C D Provided 10 3793 1.26 [32.1] 1.105 [28.07] .865 [21.97] 71 [18.0] BC 14 3314 1.46 [37.2] 1.305 [33.15] | 1.065 {27.05} G1 [23.1] BC 16 3408 1.56 [39.7] 1.405 [35.69] | 1.165 [29.59] 1.01 [25.6] ABC 20 3428 1.76 [44.8] 1,605 [40.77] | 1.365 [34.67] 1.21 [30.7] ABC 26 3429 2.06 [52.4] 1.905 [48.39] | 1.665 [42.29] 1.51 [38.3] ABC 34 3431 2.46 [62.6} 2.305 [58.55] | 2.065 [52.45] 1.91 [48.5] ABC 40 3432 2.76 [70.2] 2.605 [66.17] | 2.365 [60.07] 2.21 [56.1] ABC 50 3433 3.26 [82.9] 3.105 {78.87] | 2.865 [72.77] 2.71 [68.8] ABC 60 3372 3.76 [95.6] 3.605 [91.57] | 3.365 [85.47] 3.21 [81.5] ABC 64 3764 3.96 [100.7] | 3.805 [96.65] | 3.565 [90.55] 3.41 [86.6] ABC Table 2 3M Part Pin Cross Section Number Contact Tail Dimension E Dimension G Suffix Dimension F Diagonals Corner Radii -1XX2 some ts 42 0.0245 + 0005 | 0.028.001 | 0.0075 Ref 035 +003 -2XX2 Thick PC Board [2.84] {0.622} [0.71] [0.191] [0.89] (See Note 3) Solder Tail for -1X03 .094 [2.39] to 155 0.0245 + .0005 | 0.028 + .001 0.0075 Ref .035 + .003 -2X03 125 [3.18] [3.94] [0.622] [0.71] {0.191} [0.89] Thick PC Board -3X05 | Wire Wrap Tail for up to 61 Ref 0.0250 + .002 | 0.035 +.003 0.003 Max .045 + .003 -4X05 3 Levels of Wire Wrap [15.5] {0.635} [0.90] [0.08] [1.14] or ai6 8 @O116 @.106 @.1N6 [2.69} [2.95] 44 268) Not 3 500 (See Note 2) (10.4) (See Note 2) [7.62} Max to Edge of PCB g nig __ Side to Side Stackability pia for Daisy Chain =>) q | | ay \ _\d y ~| ! 4 2 = \. nee by. . ~e mS ie re t - - lee oS \__ e-oet ( | ft | | | a Position 1 | 029 | Postion | ro . 74 (52 | [0.74] | .100 + .003 ~o- | 100 + .003 co (2.54) | 7 | 100 + .003 232 | 352 (2.54) [5.89} {8.94] : .100 + .003 [2.54] ! B c nded Mounting Hole Pattern ting Hole Pattern (Straight) (Right Angle) Inch [mm] Tolerance Unless Noted 0 .00 | .000 Notes: 1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or M3518). inch | .1 |+.01 | +.005 2. Accepts Rear and Front mounting hardware: [ ] Dimensions for Rear Entry: #4-24 thread cutting screw, 3M Part #3341-5, .116 [2.95] dia mounting hole Reference only Front Entry: (Prior to installation of latch on Straight Versions) #2-56 bolt and nut, 3M Part #3341-6, .106 [2.69] dia mounting hole TS-0771-01 3. The recommended PCB hole size for the kinked tail positions on the .112 solder tail connector is .035 + .002. Sheet 3 of 4 3M Electronic Products Division 6801 River Place Blvd. Austin, TX 78726-9000 For technical, sales or ordering information call 800-225-5373 .100 x .100 Latch/Ejector Header 3 Wall, Straight & Right Angle, High Temp Option Ordering Information 30 Microinches Gold Plated Product KAKA OK Blank = Standard . N = High Temperature Latch/Ejector System Tail = xe bareniledior tchvElect 02 = Solder Tail for .062 [1.57] Thick Board = Short, Roll Pin Latch/Ejectors = K2=Kin| r Tai . 1. 3M Part Number (3M Part # 3505-2)" Thick boone als for 062 [1.57] (See Table 1) 3 = Long, Roll Pin Latch/Ejectors 03 =Solder Tails for .094 to .125 [2.39 to 3.18} (3M Part # 3505-3)* Thick Board 4 = Roll Pin Ejectors 05 = Wrap Posts for up to 3 Levels of Wire Wrap (3M Part # 3505-4)" (not available on High Temp version) 5 = Short, Snap-in Latch/Ejectors, (3M Part # 3505-30) Shroud and Pin Configuration 6 = Long, Snap-In Latch/Ejectors 1 = 3 Wall, Right Angle (3M Part # 3505-31) Solder Tail 2 = 3 Wail, Straight Solder Tail 3 = 3 Wall, Right Angle Wrap Post (not available on High Temp version) 4 = 3 Wall, Straight Wrap Post 15 Microinches Gold Plated Product XXXXX-XXXXUG Plating Suffix UG = 15 microinch Gold s d __ Tail mires andar ' 02 =Solder Tail for .062 [1.57] Thick Board N = High Temperature K2=Kinked Solder Tails for .062 [1.57] Thick Board 03 =Solder Tails for .094 to .125 (2.39 to 3.18] 3M Part Number Thick Board (See Table 1} Shroud and Pin Configuration Latch/Ejector System 1 = 3 Wail, Right Angle 0 = No Latch/Ejector Solder Tail 5 = Short, Snap In Latet/Ejectors 2 = 9 Wall, Straight Solder Tail (3M Part # 3505-30) 6 = Long, Snap In Latch/Ejectors (3M Part # 3505-31) : 1-01 * Roll pin Latch/Ejector available only on standard version. Shona of 4 3M Electronic Products Division 6801 River Place Blvd. For technical, sales or ordering information call Austin, TX 78726-9000 800-225-5373