Product Specification 40BASE-SR4 QSFP+ Gen2 E-Temp Optical Transceiver Module FTL410QE2N PRODUCT FEATURES * Four-channel full-duplex transceiver module * Hot Pluggable QSFP+ form factor * Maximum link length of 100m on OM3 Multimode Fiber (MMF) and 150m on OM4 MMF * Multirate capability: 1.06Gb/s to 10.5Gb/s per channel * Unretimed XLPPI electrical interface * Maximum power dissipation <1.5W * Reliable VCSEL array technology * Extended operating case temperature range: -5C to 85C * 40GBASE-SR4 40G Ethernet * * Breakout to 10GBASE-SR Ethernet Single 1x12 MPO receptacle * * Proprietary interconnections RoHS-6 Compliant APPLICATIONS Finisar's FTL410QE2N QSFP+ transceiver modules are designed for use in 40 Gigabit per second links over multimode fiber. They are compliant with the QSFP+ MSA1,2 and IEEE 802.3ba 40GBASE-SR43. Module-level digital diagnostic functions are available via an I2C interface, as specified by the QSFP+ MSA. The optical transceiver is compliant per the RoHS Directive 2011/65/EU4. See Finisar Application Note AN-2038 for more details5. PRODUCT SELECTION FTL410QE2N Finisar Corporation October 2015 Rev. D1 Page 1 FTL410QE2N Product Specification I. Pin Descriptions Figure 1 - QSFP+ MSA-compliant 38-pin connector Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Symbol GND Tx2n Tx2p GND Tx4n Tx4p GND ModSelL ResetL Vcc Rx SCL SDA GND Rx3p Rx3n GND Rx1p Rx1n GND GND Rx2n Rx2p GND Rx4n Rx4p GND Finisar Corporation October 2015 Name/Description Ground Transmitter Inverted Data Input Transmitter Non-Inverted Data Input Ground Transmitter Inverted Data Input Transmitter Non-Inverted Data Input Ground Module Select Module Reset +3.3 V Power supply receiver 2-wire serial interface clock 2-wire serial interface data Ground Receiver Non-Inverted Data Output Receiver Inverted Data Output Ground Receiver Non-Inverted Data Output Receiver Inverted Data Output Ground Ground Receiver Inverted Data Output Receiver Non-Inverted Data Output Ground Receiver Inverted Data Output Receiver Non-Inverted Data Output Ground Rev. D1 Notes 1 1 1 1 1 1 1 1 1 Page 2 FTL410QE2N Product Specification 27 28 29 30 31 32 33 34 35 36 37 38 ModPrsL IntL Vcc Tx Vcc1 LPMode GND Tx3p Tx3n GND Tx1p Tx1n GND Module Present Interrupt +3.3 V Power supply transmitter +3.3 V Power Supply Low Power Mode Ground Transmitter Non-Inverted Data Input Transmitter Inverted Data Input Ground Transmitter Non-Inverted Data Input Transmitter Inverted Data Input Ground 1 1 1 Notes 1. Circuit ground is internally isolated from chassis ground. II. General Product Characteristics Parameter Module Form Factor Number of Lanes Maximum Aggregate Data Rate Maximum Data Rate per Lane Protocols Supported Operating Case Temperature Electrical Interface and Pin-out Maximum Power Consumption per End Management Interface Data Rate Specifications Bit Rate per Lane Bit Error Ratio Link distance on OM3 MMF Link distance on OM4 MMF Value QSFP+ 4 Tx and 4 Rx 42.0 10.5 Unit Gb/s Gb/s Typical applications include 40G Ethernet, Infiniband, Fibre Channel, SATA/SAS3 -5 to +85 38-pin edge connector 1.5 Watts Min 1062 Higher bit rates may be supported. Please contact Finisar. C Serial, I2C-based, 400 kHz maximum frequency Symbol BR BER d d Notes Typ Pin-out as defined by the QSFP+ MSA Varies with output voltage swing and pre-emphasis settings (see Figure 2) As defined by the QSFP+ MSA Max 10500 10-12 100 150 Units Mb/sec meters meters Ref. 1 2 3 3 Notes: 1. Compliant with 40G Ethernet. Compatible with 1/10 Gigabit Ethernet and 1/2/4/8/10G Fibre Channel. 2. Tested with a PRBS 231-1 test pattern. 3. Per 40GBASE-SR4, IEEE 802.3ba Finisar Corporation October 2015 Rev. D1 Page 3 FTL410QE2N Product Specification III. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Damage Threshold, per Lane Symbol Vcc1, VccTx, VccRx TS T OP RH DT Min -0.5 Typ Max 3.6 Unit V 85 85 85 C C % dBm -40 -5 0 3.4 Ref. 1 Notes: 1. Non-condensing. IV. Electrical Characteristics (TOP = -5 to 85C, VCC = 3.15 to 3.45 Volts) Parameter Supply Voltage Supply Current Link turn-on time Transmit turn-on time Transmitter (per Lane) Single ended input voltage tolerance Differential data input swing Differential input threshold AC common mode input voltage tolerance (RMS) Differential input return loss J2 Jitter Tolerance J9 Jitter Tolerance Data Dependent Pulse Width Shrinkage Eye mask colordinates {X1, X2 Y1, Y2} Receiver (per Lane) Single-ended output voltage Differential data output swing AC common mode output voltage (RMS) Termination mismatch at 1 MHx Differential output return loss Symbol Vcc1, VccTx, VccRx Icc VinT Vin,pp Finisar Corporation October 2015 Typ 3.15 -0.3 180 Max Unit 3.45 V 350 mA 2000 ms 2 4.0 1200 V mVpp mV 3 50 15 Jt2 Jt9 DDPWS Vout,pp Common mode output return loss Output transition time, 20% to 80% J2 Jitter output J9 Jitter output Eye mask coordinates #1 {X1, X2 Y1, Y2} Eye mask coordinates #2 {X1, X2 Y1, Y2} Power Supply Ripple Tolerance Min Jo2 Jo9 PSR Rev. D1 Per IEEE P802.3ba, Section 86A.4.1.1 0.17 0.29 0.07 0.11, 0.31 95, 350 -0.3 0 4.0 800 7.5 5 Per IEEE P802.3ba, Section 86A.4.2.1 Per IEEE P802.3ba, Section 86A.4.2.2 28 0.42 0.65 0.29, 0.5 150, 425 0.29, 0.5 125, 500 50 Ref. mV dB 4 UI UI UI UI mV V mVpp mV % 5 7,8 dB 4 dB 4 ps UI UI UI mV UI mV mVpp 6 Page 4 5 FTL410QE2N Product Specification Notes: 1. 2. 3. 4. 5. 6. 7. 8. Maximum total power value is specified across the full temperature and voltage range. From power-on and end of any fault conditions. After internal AC coupling. Self-biasing 100 differential input. 10 MHz to 11.1 GHz range Hit ratio = 5 x 10E-5. Valid for all settings in Figure 2. Hit ratio = 5 x 10E-5. Valid only for the shaded settings in Figure 2. AC coupled with 100 differential output impedance. Settable in 4 discrete steps via the I2C interface. See Figure 2 for Vout settings. Vout (mV) Power (mW) 0 317 422 739 Pre-Emphasis into 100ohms (mV) 0 125 175 325 599 751 935 971 1075 787 971 1007 1111 883 1055 1103 1190 Figure 2 - Power Dissipation (mW, maximum) vs. Rx Output Conditions V. Optical Characteristics (TOP = -5 to 85C, VCC = 3.15 to 3.45 Volts) Parameter Transmitter (per Lane) Signaling Speed per Lane Center wavelength RMS Spectral Width Average Launch Power per Lane Transmit OMA per Lane Difference in Power between any two lanes [OMA] Peak Power per Lane Launch Power [OMA] minus TDP per Lane TDP per Lane Optical Extinction Ratio Optical Return Loss Tolerance Encircled Flux Average launch power of OFF transmitter, per lane Relative Intensity Noise Transmitter eye mask definition {X1, X2, X3, Y1, Y2, Y3} Finisar Corporation October 2015 Symbol Min Typ Max Unit Ref. GBd nm nm dBm dBm dB 1 860 0.65 0.0 3.0 4.0 10.5 840 SW TXP x TxOMA DP x PP x P-TDP TDP ER ORL FLX -7.6 -5.6 4.0 dBm dBm 3.5 dBm dB dB dBm -6.5 3.0 12 > 86% at 19 um < 30% at 4.5 um RIN -30 dBm -128 dB/Hz 2 0.23, 0.34, 0.43, 0.27, 0.35, 0.4 Rev. D1 Page 5 FTL410QE2N Product Specification Parameter Symbol Min Typ Max Unit Receiver (per Lane) Signaling Speed per Lane 10.5 GBd Center wavelength 840 860 nm Damage Threshold DT 3.4 dBm Average Receive Power per Lane RXP x -9.5 2.4 dBm Receive Power (OMA) per Lane RxOMA 3.0 dBm Stressed Receiver Sensitivity (OMA) SRS -5.4 dBm per Lane Peak Power, per lane PP x 4 dBm Receiver Reflectance Rfl -12 dB Vertical eye closure penalty, per lane 1.9 dB Stressed eye J2 jitter, per Lane 0.3 UI Stressed eye J9 jitter, per Lane 0.47 UI OMA of each aggressor lane -0.4 dBm Rx jitter tolerance: Jitter frequency (75, 5) kHz, UI and p-p amplitude (375, 1) kHz, UI LOS De-Assert LOS D -12 dBm LOS Assert LOS A -30 dBm LOS Hysteresis 0.5 dBm Notes: 1. Transmitter consists of 4 lasers operating at a maximum rate of 10.5Gb/s each. 2. Even if TDP is <0.9dB, the OMA min must exceed this value. 3. Receiver consists of 4 photodetectors operating at a maximum rate of 10.5Gb/s each. VI. Ref. 3 Memory Map and Control Registers Compatible with SFF-8436 1 and SFF-8636.2 Please see Finisar Application Note AN2079 6 for implementation details. VII. Environmental Specifications Finisar FTL410QE2N transceivers have an operating temperature range from -5C to +85C case temperature. Environmental Specifications Case Operating Temperature Storage Temperature Finisar Corporation October 2015 Symbol Min T op T sto -5 -40 Rev. D1 Typ Max Units 85 85 C C Ref. Page 6 FTL410QE2N Product Specification VIII. Regulatory Compliance Finisar FTL410QE2N transceivers are RoHS-6 Compliant. Copies of certificates are available at Finisar Corporation upon request. FTL410QE2N transceiver modules are Class 1 laser eye safety compliant per IEC 60825-1. IX. Mechanical Specifications The FTL410QE2N mechanical specifications are compliant to the QSFP+ MSA transceiver module specifications. Figure 3 - FTL410QE2N mechanical drawing Finisar Corporation October 2015 Rev. D1 Page 7 FTL410QE2N Product Specification Figure 4 - FTL410QE2N product label Ch 0 Ch 1 Ch 2 Ch 3 Ch 3 Ch 2 Figure 5 - FTL410QE2N optical lane assignment (front view of MPO receptacle) Finisar Corporation October 2015 Rev. D1 Page 8 Ch 1 Ch 0 FTL410QE2N Product Specification X. References 1. SFF-8436 - Specification for QSFP+ Copper and Optical Transceiver, Rev 4.8, October 2013. 2. SFF-8636 - Specification for Common Management Interface, Rev 1.7, January 2014. 3. IEEE 802.3ba - PMD Type 40GBASE-SR4. 4. Directive 2011/65/EU of the European Council Parliament and of the Council, "on the restriction of the use of certain hazardous substances in electrical and electronic equipment". Certain products may use one or more exemptions as allowed by the Directive. 5. "Application Note AN-2038: Finisar Implementation of RoHS Compliant Transceivers". 6. "Application Note AN-2079: QSFP Module EEPROM Mapping", Rev. G, Finisar Corporation, May, 2013. XI. For More Information Finisar Corporation 1389 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com Finisar Corporation October 2015 Rev. D1 Page 9