BU2152FS-TL - ROHM Co., Ltd.

TECHNICAL NOTE

Serial-in / Parallel-out Driver Series

Serial / Parallel

4-input Drivers

BU2050F, BU2092F/FV, BU2099FV, BD7851FP, BU2152FS

●Description

Serial-in-parallel-out driver incorporates a built-in shift register and a latch circuit to control a maximum of 24 LED by a 4-line

interface, linked to a microcontroller.

A single external resistor can set the output current value of the constant current up to a maximum of 50mA.

(BD7851FP only)

CMOS open drain output type products can drive the maximum current of 25mA.

●Features

1) LED can be driven directly.

2) Parallel output of a maximum of 24 bit

3) Operational on lo w voltage (2.7V～5.5V)

4) Cascade connection is possible (BU2050F and BU2092F/FV are not acceptable)

●Application

For AV equipment such as, audio stereo sets, videos and TV sets, PCs, control microcontroller mounted equipment.

●Product line-up

Parameter BU2050F BU2092F BU2092FV BU2099FV BD7851FP BU2152FS Unit

Output current 25 25 25 25 50 25 mA

Output line 8 12 12 12 16 24 line

Output type CMOS Open drain

Constant

current CMOS -

Package SOP14 SOP18 SSOP-B20 SSOP-B20 HSOP25 SSOP-A32 -

Mar. 2008

2/24

●Thermal derating curv e

●Absolute maximum ratings (Ta=25℃)

Parameter Symbol Limits Unit

BU2050F BU2092F BU2092FV

Power Supply Voltage VDD -0.3～+7.0 -0.3～+7.0 V

Power dissipation 1 Pd1 450 *1 450 (SOP) *2 400 (SSOPB) *3 mW

Power dissipation 2 Pd2 - 550 (SOP) *4 650 (SSOPB) *5 mW

Input Voltage VIN V

SS-0.3～VDD+0.5 VSS-0.3～VDD+0.3 V

Output Voltage Vo VSS-0.3～VDD+0.5 VSS～+25.0 V

Operating Temperature Topr -40～+85 -25～+75 ℃

Storage Temperature Tstg -55～+125 -55～+125 ℃

*1 Reduce d b y 4 .5mW/℃ over 25℃

*2 Reduce d b y 4 .5mW/℃ over 25℃

*3 Reduce d b y 4 .0mW/℃ over 25℃

*4 Reduce d b y 5 .5mW/℃ for each increase in Ta of 1℃ over 25℃ (When mounted on a board 50mm×50mm×1.6mm Glass-epoxy PCB).

*5 Reduce d b y 6 .5mW/℃ for each increase in Ta of 1℃ over 25℃ (When mounted on a board 70mm×70mm×1.6mm Glass-epoxy PCB).

Parameter Symbol Limits Unit

BU2099FV BD7851FP BU2152FS

Power Supply Voltage VDD -0.3～+7.0 0～+7.0 -0.3～+7.0 V

Power dissipation 1 Pd1 400 (SSOPB) *6 1450 *7 800 *8 mW

Power dissipation 2 Pd2 650 (SSOPB) *9 - - mW

Input Voltage VIN V

SS-0.3～VDD+0.3 -0.3～VCC+0.3 VSS-0.3～VDD+0.3 V

Output Voltage Vo VSS～+25.0 0～+10 VSS-0.3～VDD+0.3 V

Operating Temperature Topr -40～+85 -30～+85 -25～+85 ℃

Storage Temperature Tstg -55～+125 -55～+150 -55～+125 ℃

*6 Reduce d b y 4 .5mW/℃ over 25℃

*7 Reduce d by 11.6mW/℃ over 25℃

*8 Reduce d b y 8 .0mW/℃ over 25℃

*9 Reduce d b y 6 .5mW/℃ for each increase in Ta of 1℃ over 25℃ (When mounted on a board 70mm×70mm×1.6mm Glass-epoxy PCB).

700

600

500

400

300

200

100

025 50 75 100 125 150 175

Ambient temper atur e Ta [℃]

Power dissipation Pd [mW]

BU2099FV

85℃

BU2050F

25 50 75 100 125 150 175

Ambient temper atur e Ta [℃]

Power dissipation Pd [mW]

85℃

400

200

0

800

600

1200

1000

1600

1400

BU2152FS

BD7851FP

700

600

500

400

300

200

100

025 50 75 100 125 150 175

Ambient temper ature Ta [℃]

Power dissipation Pd [mW]

BU2092FV

BU2092F

3/24

●Electrical characteristics

BU2050F (Unless otherwise noted, Ta=25℃, VDD=4.5～5.5V)

Parameter Symbol Min. Typ. Max. Unit Condition

Power Supply Voltage VDD 4.5 - 5.5 V

Input high-level Voltage VIH 0.7VDD - VDD V

Input low-level Voltage VIL V

SS - 0.3VDD V

Input Hysteresis VHYS - 0.5 - V

Output high-level Voltage VOHD VDD-1.5 - VDD V IOH=-25mA

VDD-1.0 - VDD I

OH=-15mA

VDD-0.5 - VDD I

OH=-10mA

Output low-level Voltage VOLD VSS - 1.5

V IOL=25mA

VSS - 0.8 IOL=15mA

VSS - 0.4 IOL=10mA

Quiescent Current IDD - - 0.1 mA VIH=VDD, VIL=VSS

BU2092F/FV (Unless otherwise noted, Ta=25℃, VSS=0V, VDD=5.0V/3.0V)

Parameter Symbol Min. Typ. Max. Unit Condition

Power Supply Voltage VDD 2.7 - 5.5 V

Input high-level Voltage VIH 3.5 / 2.5 - - V VDD=5V/3V

Input low-level Voltage VIL - - 1.5 / 0.4 V VDD=5V/3V

Output low-level Voltage VOL - - 2.0 / 1.0 V VDD=5V/3V,

IOL=20mA/5mA

Output high-level disable Current IOZH - - 10.0 μA VO=25.0V

Output low-level disable Current IOZL - - -5.0 μA VO=0V

Quiescent Current IDD - - 5.0 / 3.0 μA VIN=VSS or VDD

(VDD=5V/3V)

OUTPUT:OPEN

BU2099FV (Unless otherwise noted, Ta=25℃, VSS=0V, VDD=5.0V/3.0V)

Parameter Symbol Min. Typ. Max. Unit Condition

Power Supply Voltage VDD 2.7 - 5.5 V

Input high-level Voltage VIH 3.5 / 2.1 - - V VDD=5V/3V

Input low-level Voltage VIL - - 1.5 / 0.9 V VDD=5V/3V

Output high-level Voltage (SO) VOH VDD-0.5

/ VDD-0.3 - - V

VDD=5V/3V,

IOH=-400μA/-100μA

Output low-level Voltage 1 (Qx) VOL1 - - 1.0

V

VDD=5V/3V,

IOL1=10mA/5mA

- - 1.5 VDD=5V, IOL1=15mA

- - 2.0 VDD=5V, IOL1=20mA

Output low-level Voltage 2 (SO) VOL2 - - 0.4 / 0.3 V VDD=5V/3V,

IOL2=1.5mA/0.5mA

Output high-level disable Current

(Qx) IOZH - - 10 μA VO=25.0V

Output low-level disable Current

(Qx) IOZL - - -5.0 μA VO=0V

IPULLDOWN (OE) IPD - - 150 / 60 μA OE= VDD, VDD=5V/3V

Low Voltage Reset VCLR 1.1 - 2.4 V

Quiescent Current IDD - - 200 μA VIN=VSS or VDD,

VDD=5V

OUTPUT:OPEN

4/24

●Electrical characteristics

BD7851FP (Unless otherwise noted, Ta=25℃, VCC=5.0V)

Parameter Symbol Min. Typ. Max. Unit Condition

Power Supply Voltage VDD 4.5 - 5.5 V

Input high-level Voltage VIH 0.8×VCC - - V

Input low-level Voltage VIL - - 0.2×VCC V

Output high-level Voltage VOH V

CC-0.5 - - V IOH=-1mA

Output low-level Voltage VOL - - 0.5 V IOL=1mA

Quiescent Current ICC

- 0.7 1.0 mA

R=13kΩ

OUT1～OUT16:OFF

- 1.8 3.0 mA

R=1.3kΩ

OUT1～OUT16:OFF

- 4.0 6.5 mA

R=13kΩ

OUT1～OUT16:ON

- 30 40 mA

R=1.3kΩ

OUT1～OUT16:ON

Reference Current Output Current

(including the equation between

each bit)

Iolc1 48 55 62 mA VOUT=2.0V, R=1.3k Ω

Iolc2 5.0 5.9 6.8 mA VOUT=2.0V, R=13kΩ

Equation between each bit of

Reference Current Output Current Δiolc - ±1 ±6 %

VOUTn=2.0V, R=1.3kΩ

(1bit : ON)

Change rate of reference current

output current for output voltage IΔVCC - ±1 ±6 %/V

VOUT=2.0～3.0V,

R=1.3kΩ

Output Leak Current IOH - 0.01 0.8 μA VOUT=10V

BU2152FS (Unless otherwise noted, Ta=25℃, VDD=2.7～5.5V)

Parameter Symbol Min. Typ. Max. Unit Condition

Power Supply Voltage VDD 2.7 - 5.5 V

Input high-level Voltage VIH 2.0 - - V VDD=5V

Input low-level Voltage VIL - - 0.6 V VDD=5V

Output high-level Voltage VOH VDD-1.5 - - V IOH=-25mA

VDD-1.0 - - IOH=-15mA

VDD-0.5 - - IOH=-10mA

Output low-level Voltage VOL - - 1.5

V IOL=25mA

- - 1.0 IOL=15mA

- - 0.8 IOL=10mA

Quiescent Current IDDST - - 5 μA VIL=VSS, VIH=VDD

Input high-level Current IIH - - 1 μA

Input low-level Current IIL - - 1 μA

5/24

●Block diagram

BU2050F

BU2092F/FV

BU2099FV

BD7851FP

BU2152FS

Controller

Shift

Register

STB

CLR

CLOCK

DAT

A

8bit

L

a

t

c

h

Write

Buffer P1～P8

Controller

Shift

Register

LCK

CLOCK

DAT

A

12bit

L

a

t

c

h

Write

Buffer Q0～Q11

OE

Controller

Shift

Register

LCK

CLOCK

DAT

A

12bit

L

a

t

c

h

Write

Buffer Q0～Q11

OE

LPF

Shift

Register

S_IN 16bit

L

a

t

c

h

Write

Buffer OUT1～OUT16

LATCH

CLOCK

Controller

Shift

Register

STB

CLB

CLOCK

DAT

A

24bit

L

a

t

c

h

Write

Buffer P1～P24

SO

ENABLE

R_Ire

f

SOUT

Current Adjustment

6/24

●Operating description

(1) Data clear

When the reset terminal (CLR, CLB) is set to “L”, the content of all latch circuits are set to “H”, and all parallel outputs are

initialised. (For model with reset terminal only)

(2) Data transfer

Serial data is sequentially input to the shift register during the rise of the c lock time (strobe signal is not active). When

the strobe signal is active, the content of the shift register are transferred to the latch circuit.

(3) Cascade connection

Serial input data is output from the serial output through the shift register, regardless of the strobe signal.

(except for BU2050F, BU209 2F/FV)

●Application circuit

Fig. 1

●Interfaces

BU2050F BU2050F BU2092F/FV BU2092F/FV

DATA, CLOCK, STB, CLR P1～P8 DATA, CLOCK, LCK, OE Q0～Q11

BU2099FV BU2099FV BU2099FV BU2152FS

DATA, CLOCK, LCK, OE Q0～Q11 SO CLOCK, DATA, STB, CLB

BU2152FS BU2152FS

P1～P28 SO

VDD

Serial data input

Clock input

Strobe input

Latch input

P1 P2 Pn-2 Pn-1 Pn

Serial data outpu

t

VSS

P1 P2 Pn-2 Pn-1 Pn

VSS

VDD

VSS

MPU

C1

(*)

(*C1 must be placed as close to the terminal as possible.)

VDD

Serial data input

Clock input

Strobe input

Latch in put Serial data outpu

t

INPUT

GND(VSS) GND(VSS)

VDD

GND(VSS)

VDD

OUTPUT

GND(VSS)

IN

GND(VSS) GND(VSS)

VDD

OUT

GND(VSS)

VDD

OUT

GND(VSS)

VSS

VDD VDD

VSS VSS GND(VSS)

VDD VDD VDD

GND(VSS) GND(VSS)

GND(VSS)

VDD VDD

GND(VSS)

VDD

GND(VSS)

VDD

GND(VSS)

VDD

GND(VSS)

VDD

IN

(only OE pin)

7/24

【BU2050F】

●Pin descriptions

Pin No. Pin Name Function

1 P3

Parallel Data Output 2 P4

3 P5

4 VSS GND

5 P6

Parallel Data Output 6 P7

7 P8

8 DATA Serial Data Input

9 CLK Clock Signal Input

10

STB Strobe Sig nal Input

In case of “L”, the data of shift register outputs.

In case of “H”, all parallel outputs and data of latch circuit do not change.

11

CLR Reset Signal Input

In case of “L”, the data of latch circuit reset, and all parallel output (P1～P8) can be L.

Normally CLR=H

12 P1

Parallel Data output

13 P2

14 VDD Power Supply

●Timing chart

Fig. 2

1. After the power is turned on and the v oltage is stabilized, ST B should be ac tivated, after clocking 8 data bits into

the DATA pin.

2. Pn parallel output data of the shift register is set after the 8th clock by the STB.

3. Since the ST B is level latch, d ata is retained in the “L” section and renewed in the “H” section of the STB.

［Function explanation］

・ A latch circuit has the reset function, which is common in all bits. In case of CLR terminal is “L”, the latch

circuit is reset non-synchronously without the other input condition, and al l parallel output can be “L”.

・ A serial data inputted from DATA terminal is read in shift register with synchronized rising of clock.

In case of STB is “L” (CLR is ”H”), transmit the data which read in the shift register to latch circuit, and

outputs from the parallel data output terminal (P1～P8).

In case of STB is “H”, all parallel outputs and the data of latch do not change.

CLK

STB

DATA DATA8 DATA7 DATA6 DATA2 DATA1

Pn Previous DATA DATA

CLR

“L”

8/24

●Switching characteristics (Unless otherwise specified, VDD=4.5～5.5V, Ta=25℃)

Parameter Symbol Limit Unit Condition

Min. Typ. Max.

Set up time (DATA-CLK) tSD 20 - - ns -

Hold time (DATA-CLK) tHD 20 - - ns -

Set up time CLK)STB( − tSSTB 30 - - ns -

Hold time CLK)STB( − tHSTB 30 - - ns -

Propagation P8)P1CLR( ～− tPDPCK - - 100 ns P1～P8 terminal load 20pF or less

Propagation P8)P1STB( ～− tPDPSTB - - 80 ns P1～P8 terminal load 20pF or less

Propagation P8)P1CLR( ～− tPDPCLR - - 80 ns P1～P8 terminal load 20pF or less

Maximum clock frequency fMAX 5 - - MHz -

●Switching T ime Test W aveform

Fig. 3

CLK

DATA

P8

P1

STB

CLR

1 2 8 9 10 11 12

fMAX

tHD

tSD

tHSTB tSSTB

tPDPSTB tPDPCL

R

tPDPCK

9/24

【BU2092F/FV】

●Pin descriptions

●Timing chart

Fig. 4

1. Af ter the power is turned on and the voltage is stabilized, LCK should be activated, after clocking 12 data bits into

the DATA terminal.

2. Qx parallel output data of the shift register is set after the 12th clock by the LCK.

3. Since the LCK is a label latch, data is retained in the “L” section and renewed in the “H” section of the LCK.

4. Data retained in the internal latch circuit is output when the OE is in the “L” section.

［T ruth Table］

Input Function

CLOCK DATA LCK OE

× × × H Output (Q0～Q11) Disable

× × × L Output (Q0～Q11) Enable

L × × Store “L” in the first stage data of shift register, the prev ious stage data in the

others. (The conditions of storage register and output have no change.)

H × × Store “H” in the first stage data of shift register, the previous stage data in the

others. (The conditions of storage register and output have no change.)

× × × The data of shift register has no change.

× × × The data of shift register is transferred to the storage register.

× × × The data of storage register has no change.

Pin No. Pin Name I/O Function

1 VSS - GND

2 DATA I Serial Data Input

3 CLOCK I Shift clock of DATA (Rising Edge Trigger)

4 LCK I Latch clock of DATA (Rising Edge Trigger)

5～11,

14～18 Q0～Q11 O

Parallel Data Output (Nch Open Drain FET)

Latch Data L H

Output FET ON OFF

12, 13 N.C. - Non conn ected

17 OE I Output Enable (“H” level : output FET is OFF)

18 VDD - Power Supply

CLOCK

LCK

DATA DATA11 DATA10 DATA9 DATA1 DATA0

OE

Qx Previous DA

T

A

DATA11～0

“H”

Note) Diagram shows a status where a pull-up resistor is connected to output.

10/24

●Switching characteristics (Unless otherwise specified, VDD=5V, VSS=0V, Ta=25℃)

Parameter Symbol Limit Unit Condition

Min. Typ. Max. VDD(V)

Minimum Clock Pulse Width tw 1000 - - ns 3 -

500 - - ns 5

Minimum Latch Pulse Width

(LCK)

tw

(LCK)

1000 - - ns 3 -

500 - - ns 5

Setup T ime

(LCK→CLOCK) ts 400 - - ns 3 -

200 - - ns 5

Setup T ime

(DATA→CLOCK) tsu 400 - - ns 3 -

200 - - ns 5

Hold T ime

(CLOCK→DATA) tH 400 - - ns 3 -

200 - - ns 5

Propagation

(LCK→OUTPUT QX )

tPLZ

(LCK)

- 90 - ns 3

RL=5kΩ

CL=10pF

- 55 - ns 5

tPZL

(LCK)

- 115 - ns 3 RL=5kΩ

CL=10pF

- 50 - ns 5

Propagation

(OE →OUTPUT QX)

tPLZ - 70 - ns 3 RL=5kΩ

CL=10pF

- 45 - ns 5

tPZL - 80 - ns 3 RL=5kΩ

CL=10pF

- 35 - ns 5

●Switching Time Test Circuit

Fig. 5

CLOCK

Pulse

Gen.

DAT A

Pulse

Gen.

Q11

RL

±25V

Q0

RL

±25V

VDD

GND (Vss)

Pulse

Gen.

Pulse

Gen.

LCK

OE

GND (Vss)

CL

11/24

【BU2092F/FV】

●Switching T ime Test W aveforms

Fig. 6

CLOCK

DATA

tSU

90%

10%

90% 90%

tH

90% 90%

10%

90%

10%

tWtW

50%

LCK 50%

90%

10%

tS

90%

tW(CLK)

50% 50%

OE

Qx

tPLZ(LCK) tPZL(LCK)

10% 50% 10%

tPLZ

50%

tPZL

VDD

GND

(

VSS

)

VDD

GND

(

VSS

)

VDD

GND

(

VSS

)

VDD

GND

(

VSS

)

VDD

GND

(

VSS

)

12/24

【BU2099FV】

●Pin descriptions

Pin No. Pin Name I/O Function

1 VSS - GND

2 N.C. - Non connected

3 DATA I Serial Data Input

4 CLOCK I Shift clock of Shift register (Rising Edge Trigger)

5 LCK I Latch clock of Storage register (Rising Edge Trigger)

6～17 Q0～Q11

(Qx) O Parallel Data Output (Nch Open Drain FET)

Latch Data L H

Output FET ON OFF

18 SO O Serial Data Output

19 OE I Output Enable Control Input ＊OE pin is pulled down to Vss.

20 VDD - Power Supply

●Timing chart

Fig. 7

1. Af ter the pow er is turned on and the voltage is stabilized, LCK should be activates, after clocking 12 data bits into

the DATA terminal.

2. Qx parallel output data of the shift register is set after the 12th clock by the LCK.

3. Since the LCK is a label latch, data is retained in the “L” section and renewed in the “H” section of the LCK.

4. Data retained in the internal latch circuit is output when the OE is in the “L” section.

5. The final stage data of the shift register is output to the SO by synchronizin g with the rise time of the CLOCK.

［T ruth Table］

Input Function

CLOCK DATA LCK OE

× × × H All the output data output “H” with pull-up.

× × × L The Q0～Q11 output can be enable and output the data of storage register.

L × × Store “L” in th e first stage data of shift register, the previous stage data in the

others. (The conditions of storage register and output have no change.)

H × × Store “H” in the first stage data of shift register, the previous stage data in the

others. (The conditions of storage register and output have no change.)

× × × The data of shift register has no change.

SO output s the fina l sta ge dat a of shif t reg ister with sy nchronized falling edge

of CLOCK, not controlled by OE.

× × × The data of shift register is transferred to the storage register.

× × × The data of storage register has no change.

＊The Q0～Q11 output have a Nch open drain Tr. The Tr is ON when data from shift register is “L”, and Tr is OFF when data is “H”.

CLOCK

LCK

DATA DATA12 DATA11 DATA10 DATA2 DATA1

OE

Qx Previous DATA DATA

SO Previous

DATA 11 Previous

DATA 11 DATA12 DATA11

“H”

13/24

【BU2099FV】

●Switching characteristics (Unless otherwise specified, VDD=5V, VSS=0V, Ta=25℃)

Parameter Symbol Limit Unit Condition

Min. Typ. Max. VDD(V)

Minimum Clock Pulse Width

(CLOCK) tW 1000 - - ns 3 -

500 - - ns 5

Minimum Latch Pulse Width

(LCK) tW

(LCK) 1000 - - ns 3 -

500 - - ns 5

Setup Time

(LCK→CLOCK) tS 400 - - ns 3 -

200 - - ns 5

Setup Time

(DATA→CLOCK) tsu 400 - - ns 3 -

200 - - ns 5

Hole T ime

(CLOCK→DATA) tH 400 - - ns 3 -

200 - - ns 5

Propagation

(SO) tPLH

tPHL - - 500 ns 3 -

- - 250 ns 5 -

Propagation

(LCK→QX) *

tPLZ

(LCK) - 360 - ns 3

RL=5kΩ

CL=10pF

- 170 - ns 5

tPZL

(LCK) - 260 - ns 3 RL=5kΩ

CL=10pF

- 175 - ns 5

Propagation

(QE →QX) *

tPLZ - 115 - ns 3 RL=5kΩ

CL=10pF

- 85 - ns 5

tPZL - 175 - ns 3 RL=5kΩ

CL=10pF

- 65 - ns 5

Noise Pulse Suppression

Time (LCK) * tI - 30 ns - -

- 20 ns -

*Reference value

●Input Voltage Test Circuit

Fig. 8

●Switching Time Test Circuit

Fig. 9

RL =10kΩ

GND

(Vss)

P.G.

VIH

VIL

GND

RL =5kΩ

VDD

GND

(Vss)

P.G.

GND

(Vss)

CL =10pF

+25V

RL =5kΩ

GND

(Vss)

CL =10pF

+25V

14/24

【BU2099FV】

●Output Voltage Test Circuit

Fig. 10

●Switching T ime Test W aveforms

Fig. 11

VDD

GND

(Vss)

P.G.

GND

(Vss) GND

(Vss)

IOL2IOH

SW4

1 2

±25V

SW2

1

23

SW1

1

12

SW3

Test condition

VOL1 ：Set all data “L”. SW1=”ON”, SW2=”3”, SW3=”1”～”12”.

VOL2 ：Set output data “L” to SO and SW4 is positioned to “2”, then voltage is measured at IOL2.

VOH ：Set output data “H” to SO and SW4 is positioned to “1”, then voltage is meas ured at IOH.

CLOCK

DATA

tSU

90%

10%

90% 90%

tH

90% 90%

10%

90%

10%

tWtW

50%

LCK 50%

90%

10%

tS

90%

tW (CLK)

50% 50%

OE

Qx

tPLZ

tPZL(LCK)

10% 50% 10% 50%

tPZL

VDD

GND (VSS)

V

DD

GND (VSS)

V

DD

GND (VSS)

VDD

GND (VSS)

V

EXT

GND (VSS)

50% 50%

50%

tS2

tPLZ(LCK)

SO 50% 50%

tPLH tPHL

VDD

GND (VSS)

IOL1

15/24

【BD7851FP】

●Pin descriptions

Pin No. Pin Name Function

1 GND Ground

2 R_Iref Reference Current Output Current setting

3 LATCH Latch Signal Input

4 S_IN Serial Data Input

5～15 OUT16

～OUT6 Reference Current Output

16 P_GND Ground for Driver

17～21 OUT5

～OUT1 Reference Current Output

22 SOUT Serial Data Output

23 CLOCK Clock Input

24 ENABLE ENABLE

25 VCC V

CC

●Timing chart

Fig. 12

1. After the power is turned on and the voltage is stabilized, LATCH should be activated, after clocking 16 data bits

into the S_IN terminal.

2. OUTn parallel output data of the shift register is set after the 16th clock by the LATCH.

3. The final stage data of the shift register is outputted to the SOUT by synchronizing with the rise time of the

CLOCK.

4. Since t he LATCH is a label latch, data is retained in the “L” section and renewed in the “H” section of the LATCH.

5. Data retained in the internal l atch circuit is o utputted when the ENABLE is in the “L” s ection. When t he ENABLE

is in the “H” section, data is fixed in the “H” section.

CLOCK

LATCH

S_IN DATA16 DATA15 DATA14 DATA2 DATA1

OUTn Previous DATA DATA

SOUT Previous

DATA15 Previous

DATA14 Previous

DATA2 DATA16

ENABLE

16/24

【BD7851FP】

●Timing characteristics (Unless otherwise specified, VCC=5V, Ta=25 ℃)

Parameter Symbol Limit Unit Condition

Min. Typ. Max.

Frequency CLOCK fclk - - 10 MHz

Pulse Width CLOCK twh 20 50 - ns CLOCK

Pulse Width LATCH twh 40 50 - ns LATCH

Pulse Width ENABLE tw 30 - - ns ENABLE

R ise Time / Fall Time tr / tf - 30 100 ns CLOCK

Setup Time tSU 30 50 - ns S_IN-CLOCK

30 50 - LATCH-CLOCK

Hold T ime th 30 50 - ns S_IN-CLOCK

30 50 - LATCH-CLOCK

Rise T ime tr - 300 - ns OUTn

- - 50 SOUT

Fall T ime tf - 300 - ns OUTn

- - 50 SOUT

Propagation tpLH - 400 650

ns

CLK-SOUT, LATCH

ENABLE-OUTn

tpHL - 300 400 CLK-SOUT, LATCH

ENABLE-OUTn

●Reference Current of Outpu t Current

＊This is a data for the standard sample, not guaranteed the characteristic.

Fig. 13

●R_Iref-VOUT

＊Notes the increase of consumption current Icc, in case sets the voltage of VOUT lower. See the graph above.

Fig. 14

0

50

100

150

200

250

0.1 1 10 100

R_Iref [kΩ]

IOUT [mA]

[Condition]

Vcc=5.0V, Vo=5.0V, Ta=25℃

0.0

0.2

0.4

0.6

0.8

1.0

1.2

1.4

1.6

1 10 100

R_Iref [kΩ]

VOUT [V]

[Condition]

Vcc=5.0V, Ta=27℃, all bit : ON

The reference current of output current is determined by the

external resistor.

(between 2pin and GND )

17/24

【BD7851FP】

●Test Circuit 1

Fig. 15

●Test Circuit 2

＊R=51Ω (note : R_Iref=1.3kΩ) , C=15pF

Fig. 16

1

2

3

4

5

6

7

8

9

10

11

12

13

19

18

17

16

15

14

25

24

23

22

21

20

BD7851FP

GND

R

_

Iref

LATCH

S

_

IN

OUT16

OUT15

OUT14

OUT13

OUT12

OUT11

OUT10

OUT9

OUT8 OUT7

OUT6

P_GND

OUT5

OUT4

OUT3

OUT2

OUT1

SOUT

CLOCK

ENABLE

Vcc

ENABLE

SOUT

CLOCK

VE

P_GND

S_IN

LATCH

R

1

2

3

4

5

6

7

8

9

10

11

12

13

19

18

17

16

15

14

25

24

23

22

21

20

BD7851FP

GND

R

_

Iref

LATCH

S

_

IN

OUT16

OUT15

OUT14

OUT13

OUT12

OUT11

OUT10

OUT9

OUT8 OUT7

OUT6

P_GND

OUT5

OUT4

OUT3

OUT2

OUT1

SOUT

CLOCK

ENABLE

Vcc

ENABLE

SOUT

CLOCK

VE

P_GND

S_IN

LATCH

R

18/24

【BD7851FP】

●Switching T ime Test W aveforms

Fig. 17

CLOCK

tSU

0.2×VCC

th

tWh

tr

0.8×VCC 0.8×VCC

0.2×VCC

tf

0.8×VCC

S_IN

0.8×VCC 0.8×VCC

LATCH

th

twh

0.8×VCC

0.2×VCC

tSU

OUTn

90%

10%

tpHL・tpLH

90%

10%

tpHL

tf

tpHL

90%

10%

tr

ENABLE 0.2×VCC

0.8×VCC

tw

SOUT

0.8×VCC

0.2×VCC

tpHL・tpLH

tf・tr

19/24

【BU2152FS】

●Pin descriptions

No. Pin Name I/O Function

1 VSS - Ground

2 CLK I Clock Input

3 VSS - Ground

4 DATA I Serial Data Input

5～28 P1～P24 O Parallel Data Output

29 SO O Cascade Output

30 STB I Strobe Signal Input active “L”

31 CLB I Clear Signal Input active “L”

32 VDD - Power Supply

●Timing chart

Fig. 18

1. Af ter the power is turned on and the voltage is stabilized, STB should be activated, after clocking 24 data bits into

the DATA terminal.

2. Pn parallel output data of the shift register is set after the 24th clock by the LCK.

3. Since t he STB is a label latch, data is retained in the “H” sect ion and renewed in the “L” se ction of the STB.

4. The final stage data of the shift register is outputted to t he SO by synchronizing with the rise time of the CLOCK.

［T ruth Table］

Input Function

CLK STB CLB

× × L

All the data of the latch circuit are set to “H” (data of shift register does not

change), all the parallel outputs are “H”.

H H

Serial data of DATA pin are latched to the shift register.

At this time, the data of the latc h circuit does not change.

L

L H

The data of the shift register are transf erred to the latch c ircuit, and the data of

the latch circuit are outputted from the parallel output pin.

H

The data of the shift register shifts 1bit, and the data of the latch circuit and

parallel output also change.

CLK

STB

DATA DATA24 DATA23 DATA22 DATA2 DATA1

SO Previous

DATA24 Previous

DATA23 Previous

DATA2 DATA24

Pn Previous DATA DATA

20/24

【BU2152FS】

●Switching characteristics (Unless otherwise specified, VDD=2.7～5.5V, VSS=0V, Ta=25 ℃)

Parameter Symbol Limit Unit Condition

Min. Typ. Max.

Maximum Clock Frequency fMAX 5 - - MHz

Setup Time 1 tSU1 20 - - ns DATA-CLK

Hold T ime 1 tHD1 20 - - ns CLK-DATA

Setup Time 2 tSU2 30 - - ns STB-CLK

Hold T ime 2 tHD2 30 - - ns CLK-STB

Setup Time 3 tSU3 30 - - ns CLB-CLK

Hold T ime 3 tHD3 30 - - ns CLK-CLB

Setup Time 4 tSU4 30 - - ns STB-CLB

Hold T ime 4 tHD4 30 - - ns CLB-STB

Output Delay Time 1* tPD1 - - 100 ns CLK-P1～P24

Output Delay Time 2* tPD2 - - 80 ns STB-P1～P24

Output Delay Time 3* tPD3. - - 80 ns CLB-P1～P24

*50pF of load is attached.

21/24

●Switching characteristic conditions

○Setup/Hold Time (DATA-CLOCK, STB-CLOCK, CLB-CLOCK)

○Setup/Hold Time (STB-CLB)

Fig. 19 Switching characteristic conditions 1

○Output Delay Time (CLOCK-P1～P24)

○Output Delay Time (STB-P1～P24)

○ Output Delay Time (CLB-P1～P24)

Fig. 20 Switching characteristic conditions 2

CLOCK

90%

10%

tr

50%

90%

10%

tr

50%

50%50%

tSU1

tHD1

tHD2 tSU2

50%50%

tHD3 tSU3

DATA

STB

CLB

50%

CLB

tSU4 tHD4

STB

50%

tPD1

CLOCK

P1～P24

50%

STB

P1～P24

tPD2

50%

CLB

50%

tPD3

22/24

●Operation Notes

1. Absolute maximum ratings

An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can

break down the dev ices, thus making impos sible to identif y breaking mode, such as a short circuit or a n open circuit. If an y

over rated values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as

fuses.

2. Connecting the power supply connector ba c kward

Connecting of the power supply in reverse polarity can damage IC. Take precautions when connecting the power supply

lines. An external direction diode can be a dded.

3. Power supply lines

Design PCB layout pattern to provi de low impedance GND and sup ply lines. To obtain a lo w noise ground a nd supply line,

separate the ground section and suppl y lines of the digital and analog bloc ks. Furthermore, f or all power supply terminals to

ICs, connect a capacitor between the power supply and the GND terminal. When applying electrolytic capacitors in the circuit,

not that capacitance characteristic values are reduced at low temperatures.

4. GND voltage

The potential of GND pin must be minimum potential in all operating conditions.

5. Thermal design

Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating co nditions.

6. Inter-pin shorts and mounti ng errors

Use caution when positioning the IC for mounting on printed circuit boards. The IC may be damaged if there is any

connection error or if pins are shorted together.

7. Actions in strong elect romagnetic field

Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction.

8. Testing on application boards

When testing t he IC on an application board, connecting a capacitor to a pin with low impedance su bjects the IC to stress.

Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or

removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic measure.

Use similar precaution when transporting or storing the I C.

9. Ground Wiring Pattern

When using both small signal and large curre nt GND patterns, it is recommended to isolate the two ground patterns, placing

a single ground point at the ground potential of application so that the pattern wiring resistance and voltage variations caused

by large currents do not cause variations in the small signal ground voltage. Be careful not to change the GND wiring pattern

of any external compon ents, either.

10. Unused input terminals

Connect all unused input terminals to VDD or VSS in order to prevent excessive current or oscill ation.

Insertion of a resistor (100k Ω approx.) is also recommended.

23/24

●Order T y pe Selections

●External Dimensions

Package type

B U 20 5 F ―E 2

F : SOP14, SOP18

FV : SSOP-B20

FP : HSOP25

FS : SSOP-A32

0

Tape

Quantity

Direction

of feed

Embossed carrier tape

2500pcs

(The direction is the 1pin of product is at the upper left when you hold

reel on the left hand and you pull out the tape on the right hand)

E2

Reel 1Pin

1234

SOP14

(Unit:mm)

1

14

8.7±0.2

7

8

4.4±0.2

6.2±0.3

0.4±0.1

0.11

1.5±0.1

0.15±0.1

0.3Min.

1.27 0.1

Direction of feed

※When you order , please order in times the amount of package quantity.

Tape

Quantity

Direction

of feed

Embossed carrier tape

2000pcs

(The direction is the 1pin of product is at the upper left when you hold

reel on the left hand and you pull out the tape on the right hand)

E2

Reel 1Pin

1234

SO

P1

8

(Unit:mm)

0.3Min.

0.4±0.1

0.11

1.8±0.1 5.4±0.2

7.8±0.3

0.15±0.1

18

1

11.2±0.2

10

9

1.27 0.1

Direction of feed

※When you order , please order in times the amount of package quantity.

Direction of feed

（Unit:mm)

SSOP-B20

11

10

20

1

0.1

6.4 ± 0.3

4.4 ± 0.2

6.5 ± 0.2

0.15 ± 0.1

0.22 ± 0.1

0.65

1.15 ± 0.1

0.3Min.

0.1

Tape

Quantity

Direction

of feed

Embossed carrier tape

2500

p

cs

E2

(The direction is the 1pin of product is at the upper left when you hold

reel on the left hand and you pull out the tape on the right hand)

Reel 1pin

1234

※When you order , please order in times the amount of package quantity.

ROHM model name Product number

BU

BD 2050

2092

2099

7851

2152

E1 :

E2 :

TL :

TR :

Emboss tape

r

eel

Pin 1 on draw-out side

Emboss tape reel

Pin 1 opposite draw-out side

Emboss tape reel

Pin 1 on draw-out side

Emboss tape reel

Pin 1 opposite draw-out side

24/24

HSOP25

(Unit:mm)

7.8 ± 0.3

5.4 ± 0.2

2.75 ± 0.1

1.95 ± 0.1

25 14

113

0.11

1.9 ± 0.1

0.36

±

0.1

0.3Min.

0.25 ± 0.1

13.6 ± 0.2

0.8 0.1

Tape

Quantity

Direction

of feed

Embossed carrier tape

2000pcs

(The direction is the 1pin of product is at the upper left when you hold

reel on the left hand and you pull out the tape on the right hand)

E2

Reel 1pin

1234

Direction of feed

※When you order , please order in times the amount of package quantity.

(Unit:mm)

SSOP-A32

0.15 ± 0.1

0.3Min.

7.8 ± 0.3

5.4 ± 0.2

1.8 ± 0.1

0.11

1

32

0.36 ± 0.1

16

17

13.6 ± 0.2

0.8 0.1

Tape

Quantit

y

Direction

of feed

Embossed carrier tape

2000pcs

E2

(The direction is the 1pin of product is at the upper left when you hold

reel on the left hand and you pull out the tape on the right hand)

Reel Direction of feed

1pin

1234

※When you order , please order in times the amount of package quantity.

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any

means without prior permission of ROHM CO.,LTD.

The contents described herein are subject to change without notice. The specifications for the

product described in this document are for reference only. Upon actual use, therefore, please request

that specifications to be separately delivered.

Application circuit diagrams and circuit constants contained herein are shown as examples of standard

use and operation. Please pay careful attention to the peripheral conditions when designing circuits

and deciding upon circuit constants in the set.

Any data, including, but not limited to application circuit diagrams information, described herein

are intended only as illustrations of such devices and not as the specifications for such devices. ROHM

CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any

third party's intellectual property rights or other proprietary rights, and further, assumes no liability of

whatsoever nature in the event of any such infringement, or arising from or connected with or related

to the use of such devices.

Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or

otherwise dispose of the same, no express or implied right or license to practice or commercially

exploit any intellectual property rights or other proprietary rights owned or controlled by

ROHM CO., LTD. is granted to any such buyer.

Products listed in this document are no antiradiation design.

Appendix1-Rev2.0

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact your nearest sales office.

ROHM Customer Support System THE AMERICAS / EUROPE / ASIA / JAPAN

Contact us : webmaster@ rohm.co.jp

www.rohm.com

The products listed in this document are designed to be used with ordinary electronic equipment or devices

(such as audio visual equipment, office-automation equipment, communications devices, electrical

appliances and electronic toys).

Should you intend to use these products with equipment or devices which require an extremely high level

of reliability and the malfunction of which would directly endanger human life (such as medical

instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers

and other safety devices), please be sure to consult with our sales representative in advance.

It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance

of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow

for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in

order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM

cannot be held responsible for any damages arising from the use of the products under conditions out of the

range of the specifications or due to non-compliance with the NOTES specified in this catalog.

21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121

FAX : +81-75-315-0172

Appendix