www.andersonpower.com
- 20 - All Data Subject To Change Without Notice
| PP15-45 ORDERING INFORMATION |
PP15-45 series are the smallest Powerpole® housings. They can be used for wire-to-wire or wire-
to-board applications. Wire sizes from #20 AWG (0.75 mm²) to #10 (6 mm²) offer power capabilities
up to 55 amps per pole. Finger proof housings and the ability to incorporate rst-mate last-break
ground connectors enhance the capabilities of this Powerpole® series.
High Power Density
• Up to 55 amps in a compact footprint
Wire-to Wire & Wire-to-Board Congurations
• Wire & PCB contacts can be used in the same housings
Finger Proof Housings Available
• Protects against accidental contact with live circuits
Powerpole® Connectors
- PP15 to PP45 :
up to 55 Amps
Finger Proof
Rib Feature
[ 17.27 ]
0.68
[ 3.81 ]
0.15
[ 6.35 ]
0.25
A
Open Barrel Contact
SECTION 2
Powerpole® PP15 to 45
45A Premate Ground Housings
Green housings are keyed to prevent accidental mating
with standard or nger proof Powerpole® housings.
Description ------- Part Number -------
Minimum Quantity ... 2,500 200 ...
Green 1827G1-BK 1827G1
PP15-45 Finger Proof Housings
Improved on the original APP® design by adding ribs to mating interface to protect against accidental
contact with live circuits. Meets the requirements of UL1977 section 10.2 and is rated IP20. Will not
mate with standard housings.
Description ------------ Part Numbers ------------
Minimum Quantity ... 2,500 200 .....
Red 1327FP-BK 1327FP
Green 1327G5FP-BK 1327G5FP
Black 1327G6FP-BK 1327G6FP
White 1327G7FP-BK 1327G7FP
Blue 1327G8FP-BK 1327G8FP
Yellow 1327G16FP-BK 1327G16FP
PP15-45 Standard Housings
The original housing design has an open interface and is available
in a wide array of colors. Will not mate with nger proof housings.
Description ------- Part Numbers ------
Minimum Quantity ... 2,500 200 ...
Red 1327-BK 1327
Green 1327G5-BK 1327G5
Black 1327G6-BK 1327G6
White 1327G7-BK 1327G7
Blue 1327G8-BK 1327G8
Yellow 1327G16-BK 1327G16
Orange 1327G17-BK 1327G17
Gray 1327G18-BK 1327G18
Brown 1327G21-BK 1327G21
Pink 1327G22-BK 1327G22
Purple 1327G23-BK 1327G23
PP15-45 Tin Plated Power Contacts
Offer cost effective performance up to 1,500 mating cycles. See specications and temperature
charts for amperage ratings by wire size.
Dimensions
Mating Loose Piece Reeled - A -
Barrel AWG mm² Force -------- Part Numbers ------- inches mm
Minimum Quantity ....................................... 200 5,000 .........................
Open 14 to 10 K* 2.1 to 5.3 High 269G3-LPBK 269G3 0.21 5.33
Open 14 to 10 K* 2.1 to 5.3 Low 261G2-LPBK 261G2 0.20 5.08
Open 14 to 10 SF* 2.1 to 6.0 High 201G1H-LPBK 201G1H 0.24 6.10
Open 14 to 10 SF* 2.1 to 6.0 Low 200G1L-LPBK 200G1L 0.24 6.10
Open 16 to 12 1.3 to 3.3 High 269G1-LPBK 269G1 0.18 4.57
Open 16 to 12 1.3 to 3.3 Low 261G1-LPBK 261G1 0.18 4.57
Open 20 to 16 0.52 to 1.3 High 269G2-LPBK 269G2 0.16 4.06
Open 20 to 16 0.52 to 1.3 Low 262G1-LPBK 262G1 0.16 4.06
Open 20 to 16 SF* 0.52 to 1.5 Low 200G2L-LPBK 200G2L 0.20 5.08
K* - For #10 AWG class K stranded wire or smaller. For larger wires use superex contacts.
SF*- Indicates wires with high stranding such as Super Flex.
PP15-45 Finger Proof & Standard & Ground Housing Dimensions
Front View
Mated Length
[ 24.6 ]
0.97
[ 41.2 ]
1.62
[ 8.4 ]
0.33
[ 7.9 ]
0.31
[ 7.9 ]
0.31
www.andersonpower.com - 21 -
All Data Subject To Change Without Notice
See website for PCB layout drawing.
SECTION 2
Powerpole® PP15 to 45
Open Barrel Contact
A
B
[ 16.26 ]
0.64
[ 3.81 ]
0.15
[ 7.35 ]
0.29
[ 17.27 ]
0.68
[ 3.81 ]
0.15
[ 6.35 ]
0.25
A
Closed Barrel Contact
[ 9.9 ]
0.39
A
B
[ 3.1 ]
0.12 A
Housing end
[ 19.1 ]
0.75
[ 6.4 ]
0.25
[ 3.6 ]
0.14
[ 6.1 ]
0.24
[ 6.1 ]
0.24
Open Barrel Premate Contact
PP15-45 Silver Plated Power Contacts
Maximize performance by offering up to 10,000 mating cycles and are recommended for circuit interrupt or
hot plug applications. See specications and temperature charts for amperage ratings by wire size. Only closed
barrel contacts are suitable for soldering.
Dimensions
Mating Loose Piece Reeled - A - - B -
Barrel AWG mm² Force -------- Part Number --------- Part Number inches mm inches mm
Minimum Quantity .......................................... 5,000 200 5,000 .................................................
Open 14 to 10 K* 2.1 to 5.3 Low - 261G3-LPBK 261G3 0.20 5.08 - -
Open 14 to 10 SF* 2.1 to 6.0 High - - 201G3H 0.24 6.10 - -
Open 14 to 10 SF* 2.1 to 6.0 Low - 200G3L-LPBK 200G3L 0.24 6.10 - -
Open 16 to 12 1.3 to 3.3 Low - 261G4-LPBK 261G4 0.18 4.57 - -
Open 20 to 16 0.52 to 1.3 Low - 262G2-LPBK 262G2 0.16 4.06 - -
Open 20 to 16 SF* 0.52 to 1.5 Low - - 200G4L 0.20 5.08 - -
Closed 16 to 12 1.3 to 3.3 Low 1331-BK 1331 - 0.15 3.81 0.10 2.54
Closed 20 to 16 0.52 to 1.3 Low 1332-BK 1332 - 0.12 3.05 0.07 1.78
K* - For #10 AWG class K stranded wire or smaller. For larger wires use superex contacts.
SF*- Indicates wires with high stranding such as Super Flex.
45A Premate Ground Wire Contacts
Tin or silver plated contacts are rated for ground or power. Hand tools are available for loose piece
contacts. Reeled contacts can be used with high volume press and applicator tooling. Tin contacts
are rated for up to 1,500 mating cycles. Silver contacts are rated up to 10,000 mating cycles.
Reeled
Mating Loose Piece Part
Type AWG mm² Force - Part Numbers - - Numbers -
Minimum Quantity ............................................. 200 5,000 .....
Open, Tin 14 to 10 2.1 to 6.0 Low 1830G1-LPBK 1830G1
Open, Silver 14 to 10 2.1 to 6.0 Low 1830G2-LPBK 1830G2
25A Right Angle PCB Contacts Tin Plated
Suitable for right angle applications up to 25A per pole. Tin plating enhances solderability.
Cannot be mixed with 45A PCB contacts. For mating with wire contacts only.
Dimensions
Mating Loose Piece - A - - B -
Row Force ------- Part Numbers ------- inches mm inches mm
Minimum Quantity ... 1,000 100 ...................................................
Top Low 1377G1-BK 1377G1 0.59 14.80 1.52 38.60
High 1317G1-BK 1317G1
Bottom Low 1377G2-BK 1377G2 0.29 7.20 1.36 34.50
High 1317G2-BK 1317G2
Top Low 1377G11-BK 1377G11 0.59 14.80 1.21 30.70
High 1317G11-BK 1317G11
Bottom Low 1377G12-BK 1377G12 0.29 7.20 1.01 25.70
High 1317G12-BK 1317G12
25A Vertical PCB Contacts Tin Plated
For mating with wire contacts only. Suitable for vertical applications up to 25A per pole,
tin plating enhances solderability.
Dimensions
Mating Loose Piece - A -
Force ---------------- Part Numbers --------------- inches mm
Minimum Quantity .... 1,000 100 .......................
Low 1377G3-BK 1377G3 2.22 56.40
High 1317G3-BK 1317G3 2.22 56.40
Low 1377G4-BK 1377G4 1.76 44.70
High 1317G4-BK 1317G4 1.76 44.70
Low 1377G13-BK 1377G13 1.17 29.70
High 1317G13-BK 1317G13 1.17 29.70
45A Right Angle and Vertical PCB Contacts Tin Plated
Suitable for right angle or vertical applications up to 45A per pole. Tin plating
enhances solderability. Right angle contacts cannot be mixed with 25A PCB
contacts. For mating with wire contacts only.
Loose Piece
Description ----------- Part Numbers -----------
Minimum Quantity ............. 1,000 100 ....................
Vertical 3-5911P1 1335G1
Right Angle Bottom Row 3-5912P1 1336G1
Right Angle Top Row 3-5913P1 1337G1
[ 5.1 ]
0.20
[ 7.9 ]
0.31
TYP
[ 29.7 ]
1.17
REF
[ 7.9 ]
0.31
TYP
Vertical
[ 36.5 ]
1.44
[ 28.6 ]
1.13
[ 5.8 ]
0.23 [ 16.3 ]
0.64
Right Angle Contact
Horizontal (top), Cat.No. 1337G1
Right Angle Contact
Horizontal (bottom)
Cat.No. 1336G1
PP15/45 Housings
(1327 Series)
Use mounting staples with right angle contacts
(see accessories).
Use mounting staples with right angle contacts (see accessories).
www.andersonpower.com
- 22 - All Data Subject To Change Without Notice
SECTION 2
Powerpole® PP15 to 45
45A Premate Ground PCB Contacts
Right angle contacts are suitable for power or ground. Use to mate with 45A
ground wire contacts. Tin plated contacts are rated up to 1,500 mating cycles.
Can be used with other 45A PCB connectors in the bottom row.
Mating Loose Piece
Force ------- Part Numbers -------
Minimum Quantity ................... 1000 100 ....
PCB, Bottom Row Low 3-5952P1 1836G1
Pre-mate wire
connector
[ 45.3 ]
1.78 [ 41.2 ]
1.62
[ 14.7 ]
0.578
[ 7.9 ]
0.31 TYP
[ 8.4 ]
0.33 TYP
[ 7.9 ]
0.31
[ 28.1 ]
1.11
[ 5.6 ]
0.22
[ 3.6 ]
0.14
Mated Pair
| PP15-45 ULTRASONICALLY BONDED ASSEMBLIES |
Assemblies feature housings that are ultrasonically welded to create a one piece connector unit using an APP® special process. After welding,
retaining pins are no longer required to secure the stacked housings to each other. This allows Powerpole® 15-45 connectors to be used as a
durable one piece connector header. Contact customer service for congurations not shown below.
Single Row 1x2 Assemblies
Housings with Housings with
45A Vertical 45A Right Angle Color & Type
Circuit Description Housings Only PCB Contacts PCB Contacts Position Matrix
Minimum Quantity ................................ 500 500 500 ..... 1 2
DC 2 Wire Standard Housings ASMPP30-1X2-RK ASMPV45-1X2-RK ASMPR45-1X2-RK RED / STD BLK / STD
DC 2 Wire Reverse Standard Housings ASMPP30-1X2-KR ASMPV45-1X2-KR ASMPR45-1X2-KR BLK / STD RED / STD
DC 2 Wire Finger Proof ASMFP30-1X2-RK ASMFV45-1X2-RK ASMFR45-1X2-RK RED / FP BLK / FP
DC 2 Wire Finger Proof Reverse ASMFP30-1X2-KR ASMFV45-1X2-KR ASMFR45-1X2-KR BLK / FP RED / FP
Single Row 1x3 Assemblies
Housings with Housings with
45A Vertical 45A Right Angle Color & Type
Circuit Description Housings Only PCB Contacts PCB Contacts Position Matrix
Minimum Quantity ................................ 500 500 500 ..... 1 2 3
DC 2 Wire Finger Proof with Ground ASMFP30-1X3-KER N/A ASMFR45-1X3-KER BLK / FP GRN / GND RED / FP
AC Single Phase Finger Proof ASMFP30-1X3-KEW ASMFV45-1X3-KEW ASMFR45-1X3-KEW BLK / FP GRN / GND WHT / FP
Two Row 2x1 Assemblies
Housings with Housings with
45A Vertical 45A Right Angle Color & Type
Circuit Description Housings Only PCB Contacts PCB Contacts Position Matrix
Minimum Quantity ................................ 500 500 500 .... 1 2
DC 2 Wire Finger Proof ASMFP30-2X1-KR ASMFV45-2X1-KR ASMFR45-2X1-KR BLK / FP RED / FP
DC 2 Wire Finger Proof Mate ASMFP30-2X1-RK ASMFV45-2X1-RK ASMFR45-2X1-RK RED / FP BLK / FP
Two Row 2x2 Assemblies
Housings with Housings with
45A Vertical 45A Right Angle Color & Type
Circuit Description Housings Only PCB Contacts PCB Contacts Position Matrix
Minimum Quantity ................................ 500 500 500 ..... 1 2 3 4
AC 3 Phase, 3 Wire Finger Proof ASMFP30-2X2-KRWE N/A N/A BLK / FP RED / FP WHT / FP GRN / GND
AC 3 Phase, 3 Wire Finger Proof Mate ASMFP30-2X2-WEKR N/A ASMFR45-2X2-WEKR WHT / FP GRN / GND BLK / FP RED / FP
Type
STD = Standard Housing
FP = Finger Proof Housing
GND = Ground Housing
Single Row 1x2 Assembly Single Row 1x3 Assembly
Two Row 2x1 Assembly Two Row 2x2 Assembly
1 2 1 2 3 1
2
1 2
3 4
Hood Up
www.andersonpower.com - 23 -
All Data Subject To Change Without Notice
Powerpole® Pak connector shells enclose stacked
groupings of PP15-45 sized housings in a durable black
shell for a nished connector appearance and additional
features. Inline, panel mount, and blindmate congurations
are available. Plug shells offer the option of integral latches
and strain relief to help secure your connection.
• Package Groupings of PP15-45 Connectors
Provides a nished appearance while protecting the individual
connectors with an outer shell
• Inline, Panel Mount, “T” or Blindmate Congurations
Allows one connection system to meet multiple needs
• Optional Latching and Strain Relief
Secures your connection and wires
| Powerpole® Pak ORDERING INFORMATION |
Plug Shell without Latch
Can mate inline with other plug shells with or without latches, or mate to a panel
mount receptacle. For use with Powerpole® wire connectors only. Cable Clamp
and Hardware Pak or Retaining Pins must be ordered separately.
Dimensions
- A -
Description -------------- Part Numbers -------------- inches mm
Minimum Quantity ... 1,000 500 25 .............................
Black, 2-4 Poles 1461G1-BK - 1461G1 1.24 31.50
Black, 5-6 Poles - 1461G2-BK 1461G2 1.56 39.62
Black, 7-8 Poles - 1461G3-BK 1461G3 1.87 47.50
For environmentally sealed connector shells to hold Powerpole®
15-180 connectors, see APP®’s SPEC Pak® product series on our
website, www.andersonpower.com
Snap-in
T-Pak Plug shell
without latch
Plug shell
with latch
Blindmate
Powerpole® Pak Connectors
- PP15 to PP45
Powerpole® housings and contacts are sold separately.
See page 20 for ordering information.
SECTION 2
Powerpole® Pak
A
Retaining Pin
[ 53.09 ]
2.09
[ 21.59 ]
0.85
[ 49.28 ]
1.94
Side View Top View
Max wire O.D. for 2-4 pole plug shells is 0.60 inches [15.2mm²].
For all other plug shells is 0.63 inches [ 16.0 mm²].
Side View
Top View
C
D
B
Retaining Pin
[ 21.59 ]
0.85
NOTE: Retaining pins are used to secure and position
Powerpoles® in one of three positions in plug shells.
Plug Shell with Latch
Can mate inline with other plug shells without latches, or mate to a panel mount receptacle. For use
with Powerpole® wire connectors only. Cable Clamp and Hardware Pak or Retaining Pins must
be ordered seperately.
Dimensions
- B - - C - - D -
Description ------------- Part Numbers -------------- inches mm inches mm inches mm
Minimum Quantity ..... 1,000 500 25 ................................................................................
Black, 2-4 Poles 1460G1-BK - 1460G1 1.94 49.28 2.25 57.15 1.24 31.50
Black, 5-6 Poles - 1460G2-BK 1460G2 1.94 49.28 2.25 57.15 1.56 39.62
Black, 7-8 Poles - 1460G3-BK 1460G3 1.94 49.28 2.25 57.15 1.87 47.50
Black, 9-10 Poles - 1460G4-BK 1460G4 2.51 63.75 2.82 71.63 1.84 46.74
www.andersonpower.com
- 24 - All Data Subject To Change Without Notice
SECTION 2
Powerpole® Pak
Plug Shell With Latch Shown
Shell, housing and contacts
are sold separately.
Retaining Pin
Conduit Clamp
With Screws
Retaining Pin
[ 27.94 ]
1.10
[ 1.78 ]
0.07 [ 19.56 ]
0.77
E
NOTE: Retaining pins are used to secure and
position Powerpoles® in one of two positions in
receptacle shells.
Retaining Pin
Cable Clamp
With Screws
Shell, housing and contacts
are sold separately.
Plug Shell Without Latch Shown
Shell and housing are
sold separately.
Clamp
Retaining
Pins
Screws
NEW
NEW
Plug Shell with Latch & Non-Conductive Strain Relief
New 2X3 Powerpole Pak offers an improved ergonomic shell for easier latch operation as
well as a plastic, non-conductive strain relief. The new strain relief can accommodate up
to a 6 conductor #10 AWG cable. Can mate to a panel mount receptacle. For use with
Powerpole® wire connectors only. Cable Clamp and Hardware Pak or Retaining Pins
must be ordered separately. To be used with 115G23 cable clamp only.
Description -------- Part Numbers -------
Minimum Quantity 1,000 25 ...
Black, 5-6 Poles 1460G23-BK 1460G23
Snap-in Receptacle Shell
Mate to plug shells with or without latches, or mate to another panel mount receptacle to create a bulkhead to
bulkhead connection. For use with Powerpole® wire or PCB connectors. Order the number of retaining pins for
each receptacle as shown below separately.
Number of Dimensions Knock Out Size
Retaining Pins - E - - Width -
Description ---------------- Part Numbers ---------------- to Order inches mm inches mm
Minimum Quantity ... 1,000 500 25 ...............................................................................
Black, 2-4 Poles 1470G1-BK - 1470G1 1 1.50 38.10 1.25 31.75
Black, 5-6 Poles - 1470G2-BK 1470G2 2 1.88 47.75 1.62 41.15
Black, 7-8 Poles - 1470G3-BK 1470G3 3 2.13 54.10 1.88 47.75
Black, 9-10 Poles - 1470G4-BK 1470G4 4 2.44 61.98 2.19 55.63
* Height = [25.4 mm] 1.0 in.
Cable Clamp & Hardware Pak
Includes cable clamp, 2 screws, and required amount of retaining pins for each conguration.
Screw Head Cable
Description Type Type ------------ Part Numbers ------------
Minimum Quantity .................................... 1,000 500 25 ...
2-4 Poles Straight Slot Bundled 115G1-BK - 115G1
5-6 Poles Straight Slot Bundled 115G2-BK - 115G2
7-8 Poles Straight Slot Bundled 115G3-BK - 115G3
9-10 Poles Straight Slot Bundled - 115G4-BK 115G4
2-4 Poles Philips Bundled 115G7-BK - 115G7
5-6 Poles Philips Bundled 115G8-BK - 115G8
Cable Clamp & Hardware Pak
Includes 2 cable clamp halfs, 2 screws and 2 retaining pins. To be used with
1460G23 Plug Shell only.
Screw Head Cable
Description Type Type ------ Part Numbers ------
Minimum Quantity ….…… 1,000 25
5-6 Poles Philips Bundled 115G23-BK 115G23
Flexible Conduit Clamp & Hardware Pak
Includes cable clamp, 2 screws, and need amount of retaining pins for each conguration.
Description - Part Number -
Minimum Quantity ...... 100 ......
2-4 Poles 110G10
Retaining Pin for Snap-in Receptacle
Order the number of retaining pins for each receptacle shown in the Snap-in Receptacle
Shell ordering information. Pins are also required for the plug side when the Cable Clamp &
Hardware Pak is not ordered.
Description ----- Part Number ------
Minimum Quantity ..... 1,000 100 ...
Retaining Pin 110G9-BK 110G9
NOTE: Max wire O.D. for
1460G23 is 0.80 inches
[20.3 mm²].
[ 81.5 ]
3.21
[ 26.1 ]
1.03
[ 51.4 ]
2.02
[ 73.5 ]
2.90
[ 21.5 ]
0.85
www.andersonpower.com - 25 -
All Data Subject To Change Without Notice
[ 102.2 ]
4.03
[ 86.2 ]
3.39
[ 85.8 ]
3.38
[ 53 ]
2.09
[ 43.2 ]
1.70
[ 51.1 ]
2.01
Blindmate Pak Connector
Ideal for panel to panel, bulkhead to bulkhead, or rack mount applications that require the
power connector to compensate for up to 0.45 in. [11.43 mm] of misalignment in either axis.
Eight positions can be lled with Powerpole® 10-45 connectors. The receptacle side can be
used with wire or PCB contacts. Hardware bag includes retaining pins.
Description ---------- Part Numbers ----------
Minimum Quantity .................................................... 50 25 ..........
2x4 Blindmate Plug Shell, Hardware & Pins - BMPP10-45P
2x4 Blindmate Receptacle Shell, Hardware & Pins - BMPP10-45R
2x4 Blindmate Plug Shell BMHSG-P -
2x4 Blindmate Receptacle Shell BMHSG-R -
Hardware Bag Plug Side - 110G50
Hardware Bag Receptacle Side - 110G51
“T” Pak 2 Way Splitter
The Powerpole® “T” Pak connector is a 2 way electrical splitter that splits electrical current from
one incoming circuit into two outgoing circuits. The standard conguration is pre-wired for AC
3 phase, 3 wire plus ground congurations. The “T” Pak can also be used for AC single phase
plus ground or DC 2 wire plus ground applications by not using either the red or white power
positions. “T” Pak is pre-wired from the factory allowing plug and play field installation
of modular ofce and industrial equipment. UL recognition up to 20 amps and 600 volts is
achieved when mating Powerpole® Pak plugs are used with #12 AWG wire.
For OEM manufacturing scale applications, the “T” Pak can be loaded with custom
congurations of any of APP®’s nger proof, standard, or ground housings and contacts
in the PP15-45 series. Contact APP® sales or customer service for additional information.
Description - Part Numbers -
Minimum Quantity ............................ 80 ........
Assembled “T” Pak 20-01
Mating Plug Shell with Latch 2x2 26-01
Mating Plug Shell without Latch 2x2 27-01
Standard conguration for each side of the T includes (1) each Red, Black, and White Standard
PP 15-45 Housings & 261G2-LPBK contacts with (1) 45A Green Premate Ground Housing and
1830G1-LPBK contact.
Mating plug shells include (1) each Red, Black, and White Standard PP 15-45 Housings &
(3) 261G2-LPBK contacts with (1) 45A Green Premate Ground Housing and 1830G1-LPBK
contact. Cable clamp & hardware pak also included.
[ 88.6 ]
3.49
[ 76.4 ]
3.01
[ 5.0 ]
Ø 0.20 4 [ 38.6 ]
1.52
[ 58.93 ]
2.320
[ 24.38 ]
0.960
[ 13.46 ]
0.530
[ 3.05 ]
0.120
[47.24]
1.860
[ 36.7 ]
1.45
[ 50.8 ]
2.00
Plug Outline Receptacle Outline
[ 30.2 ]
1.19
[21.5]
0.85
[4.4]
0.17
[ 29.14 ]
1.147
[ 36.7 ]
1.45
[ 0.64 ]
0.025
[ 0.64 ]
0.025
A
B
C
SECTION 2
Powerpole® Pak
Mates With B Mates With A & C
27 - 01 26 - 01
See APP®’s innovative MARC Connector that offers straight-on or rotational blindmate capability.
MARC holds 6 PP15/45 power contacts and 2 PP15/45 premate ground contacts in a high temperature
housing. Visit our website, www.andersonpower.com to learn more.
www.andersonpower.com
- 26 - All Data Subject To Change Without Notice
| PP15-45 & POWERPOLE® PAK SPECIFICATIONS |
SECTION 2
Powerpole® PP15 to 45
Electrical
Current Rating Amperes¹ UL 1977 CSA/TUV
Singlepole Wire to Wire (10 AWG) 55 40
Singlepole Ground Wire to Wire or PCB (10 AWG) 45 35
3x3 Block Wire to Wire (10 AWG) 40 27
Singlepole 25A PCB to Wire (12 AWG) 25 -
2x3 Block 25A PCB to Wire (12 AWG) 25 22 *
Singlepole 45A PCB to Wire (10 AWG) 45 40 *
2x3 Block 45A PCB to Wire (10 AWG) 45 25 *
Voltage Rating AC/DC
UL 1977 600
PCB Connector Recommended Voltage³
per IEC 60950-1 Table 2L Pollution Degree2
25A Contacts Adjacent Poles 495
25A Contacts Separated by Spacer 1,000
45A Contacts Adjacent Poles 160
45A Contacts Separated by Spacer 970
Dielectric Withstanding Voltage
Volts AC 2,200
Avg. Mated Contact Resistance Milliohms¹
15A Wire Contact with 5/8” of #16 AWG 0.875
30A Wire Contact with 5/8” of #12 AWG 0.600
45A Wire Contact with 5/8” of #10 AWG 0.525
45A PCB Contact to Contact 0.500
25A PCB Contact to Contact 0.600
UL Hot Plug Current Rating Amperes
250 cycles at 72V DC 45A
250 cycles at 120V DC 30A
UL Ground Short Time Current Test - 45A Premate Ground
750 Amps, #10 AWG Wire 4 Seconds
470 Amps, #12 AWG Wire 4 Seconds
Mechanical
Wire Size Range AWG mm²
20 to 10 0.75 to 6.0
Max. Wire Insulation Diameter in. mm
0.175 4.450
Operating Temperature² °F °C
Powerpole® Housings & Powerpole® Pak Shells -4° to 221° -20° to 105°
Mating Cycles No Load by Plating Silver (Ag) Tin (Sn)
PCB to Wire - 1,500
Wire to Wire 10,000 1,500
Avg. Mating / Unmating Force Lbf. N
Low Force Wire, High Force PCB, & Ground 3 13
High Force Wire 5 22
Low Force PCB 2 9
Min. Contact / Spring Retention Force Lbf. N
20 90
Powerpole® Pak Latch Avg. Defeat Force Lbf. N
150 667
PCB Specications
Mounting Style Plated Through Hole
PCB Thickness- in. [mm] 0.090 - 0.150 (2.3-3.8)
25A PCB Recommended Traces #12 AWG Cross Section
45A PCB Recommended Traces #10 AWG Cross Section
Min. Creepage / Clearance Distance PCB in. mm
25A Creepage & Clearance Adjacent Poles 0.201 5.1
45A Creepage & Clearance Adjacent Poles 0.067 1.7
Mechanical Shock 4
MIL-STD-202 213 Condition A 50g’s
Vibration High Frequency 4
MIL-STD-202 204 Condition A 10g’s
Materials
Housing
Plastic Resin Polycarbonate
Contact Retention Spring Stainless Steel
Housing Flammability Rating
UL94 V-0
Contact
Base Copper Alloy
Plating Tin or Silver
Contact Termination Methods
Crimp³ Wire Contacts
Hand Solder 1331, 1332 & PCB Contacts
Solder Dip PCB Contacts
Wave Solder PCB Contacts
Protection
Touch Safety with Finger Proof Housings & Wire
Contacts or PCB Mating Interface
UL1977 Sec. 10.2 Pass
IEC 60950 Pass
IEC 60529 IP20
Touch Safety Standard Housings
IEC 60529 IP10
* No TUV Recognition
1 Based on: 105°C rated or better cable of the largest size, Properly calibrated APP®
recommended tooling, and a 25°C ambient temperature. UL rating not to exceed the
maximum operating temperature. CSA rating below a 30°C temperature rise.
2 Limited by the thermal properties of the connector plastic housing.
3 Use APP® recommended tooling only. Alternate tools may adversely affect the
performance of our connectors along with UL and CSA recognition.
4 Tested with contact part number 261G2.
www.andersonpower.com - 27 -
All Data Subject To Change Without Notice
| PP15-45 TEMPERATURE CHARTS |
25
50
75
100
125
0 5 10 15 20 25 30 35 40
PP25 PCB
Derating vs. Ambient Temperature
Temperature (°C)
Amperes Applied
Singlepole 2-Pole Multipole
PP45 PCB
Derating vs. Ambient Temperature
25
50
75
100
125
0 10 20 30 40 50 60 70
Temperature (°C)
Amperes Applied
Singlepole 2-Pole Multipole
PP15-45 Singlepole
Derating vs. Ambient Temperature
25
50
75
100
125
0 10 20 30 40 50 60 70
Amperes Applied
Temperature (°C)
10 AWG 12 AWG 14 AWG
16 AWG 18 AWG 20 AWG
25
50
75
100
125
0 10 20 30 40 50
PP15-45 Multipole
Derating vs. Ambient Temperature
Amperes Applied
Temperature (°C)
10 AWG 12 AWG 14 AWG
16 AWG 18 AWG 20 AWG
SECTION 2
Powerpole® PP15 to 45
0
10
20
30
40
50
60
0 10 20 30 40 50 60
PP15-45 Singlepole
Temperature Rise at Constant Current
Amperes Applied
Temperature (°C)
10 AWG 12 AWG 14 AWG
16 AWG 18 AWG 20 AWG
PP15-45 Multipole
Temperature Rise at Constant Current
Amperes Applied
Temperature (°C)
10 AWG 12 AWG 14 AWG
16 AWG 18 AWG 20 AWG
10
20
30
40
50
60
0
0
10 20 30 40 0
10
20
30
40
50
60
0 5 10 15 20 25 30 35 40
PP25 PCB
Temperature Rise at Constant Current
Temperature (°C)
Amperes Applied
Singlepole 2-Pole Multipole
0
10
20
30
40
50
60
0 10 20 30 40 50 60
PP45 PCB
Temperature Rise at Constant Current
Temperature (°C)
Amperes Applied
Singlepole 2-Pole Multipole
NOTE: Temperature rise charts are based on a 25°C ambient temperature. PP25 PCB charts based on 0.002 in² foil on board side, mated to #12 AWG conductor on
wire side. PP45 PCB charts based on #10 AWG equivalent copper foil on board side, mated to #10 AWG conductor on wire side.
www.andersonpower.com
- 28 - All Data Subject To Change Without Notice
| Powerpole® 15-45 Accessories |
[ 16.6 ]
0.655
[ 7.9 ]
0.312
[ 4.6 ]
0.180
Mounting Wings
[ 16.6 ]
0.655
[ 7.9 ]
0.312
[ 24.6 ]
0.968
[ 7.9 ]
0.312
[ 16.6 ]
0.655
[ 7.9 ]
0.312
Short with Hole Short without Hole Long
2 or 4 Pole 3 or 6 Pole 4 or 8 Pole
A
B
SECTION 2
Powerpole® PP15 to 45
Mounting Wing
Secure dovetailed Powerpole® 15-45 series housings by passing fasteners through the wings
in either a horizontal or vertical orientation. Useful for sheet metal panels, printed circuit boards,
and many other mounting surfaces. Fasteners not included.
Description ------- Part Numbers -------
Minimum Quantity ... 2,500 100 ....
Red 1399G9-BK 1399G9
Blue 1399G8-BK 1399G8
Spacer
Used to separate housings under high power to minimize derating. They are
recommended for squaring off a block of Powerpole® 15-45 housings for use in connector shells
and mounting clamps. Use a combination of long and short spacers opposite each other in a
mated block to add keying features or use two short spacers to avoid interference. Spacers with
holes can also be used to fasten the blocked housings to a surface with a fastener.
Description ------ Part Numbers -------
Minimum Quantity ..... 2,500 100 .....
Red, Short w/ Hole 1399G1-BK 1399G1
Red, Long 1399G2-BK 1399G2
Red, Short 1399G6-BK 1399G6
Black, Long 1399G10-BK 1399G10
Blue, Short 1399G13-BK 1399G13
White, Short w/ Hole 1399G14-BK 1399G14
White, Long 1399G17-BK 1399G17
Retaining Pins
Keep stacked Powerpole® 15-45 series housings from separating. Retaining pins are inserted in
the circular opening between two housings stacked side by side.
Dimensions
- A - - B -
Description ----- Part Numbers ----- inches mm inches mm
Minimum Quantity ... 1,000 100 ............................................................................
1 Block High H1507P38 110G16 0.094 2.390 0.250 6.350
2 Block High 111812P5 110G17 0.099 / 0.106 0.251 / 2.69 0.440 11.180
Mounting Clamp
Mounting clamps can be used for fastening a block of Powerpole® 15-45 series
housings to a panel. Connector blocks must be a complete square for the clamps
to work properly. Fastening hardware not included.
Description -- Part Numbers --
Minimum Quantity ... 100 sets of 2 .....
2 or 4 Pole 1462G1
3 or 6 Pole 1462G2
4 or 8 Pole 1462G3
www.andersonpower.com - 29 -
All Data Subject To Change Without Notice
A
B
2 Pole 4 Pole
SECTION 2
Powerpole® PP15 to 45
For environmentally sealed connector shells to hold Powerpole®
15-180 connectors, see APP®’s SPEC Pak® product series on our
website, www.andersonpower.com
PCB Mounting Staples
PCB staples are soldered into place to secure Powerpole® 15-45 series housings
in a horizontal conguration to the board. Reduce strain on soldering joints during
mating and unmating.
Dimensions
Part - A - - B -
Numbers H x W Length inches mm inches mm
Minimum Quantity 100 ................................................................................
114555P1 1 x 1 Short 0.47 12.0 0.28 7.0
114555P2 1 x 2 Short 0.47 12.0 0.57 14.5
114555P3 1 x 3 Short 0.47 12.0 0.89 22.5
114555P7 1 x 4 Short 0.47 12.0 1.20 30.5
114555P12 1 x 4 Long 0.67 17.0 1.20 30.5
114555P8 1 x 6 Short 0.47 12.0 1.83 46.5
114555P10 2 x 1 Short 0.79 20.0 0.28 7.0
114555P6 2 x 2 Short 0.79 20.0 0.57 14.5
114555P9 2 x 2 Long 0.91 23.0 0.57 14.5
114555P14 2 x 5 Long 0.91 23.0 1.52 38.5
114555P4 3 x 2 Short 1.10 28.0 0.57 14.5
Retention Clip
Retention clips prevent Powerpole® 15-45 blocks from unintended disconnects.
They feature a tab for easy insertion and removal.
Description -- Part Number --
Minimum Quantity ........ 100 .........
1 Block High 110G68
Block Lok
Block locks secure mated Powerpole® 15-45 series housings together. For use in
high vibration or shock applications where connectors are unmated infrequently.
Description - Part Numbers -
Minimum Quantity .......... 100 .........
2 Pole, Black 110G21
4 Pole, Black 110G12
Splash Boot
Splash boots protect a 2x2 block of any combination of Powerpole® 15-45 series
housings and feature snip off sealed ends for exibility in wire O.D. Designed for
through panel or inline applications. Not a hermetic seal.
Description - Part Numbers -
Minimum Quantity ........ 25 ...........
Female, Black 1441G1
Male, Black 1442G1
Shown without Powerpoles® Shown with Powerpoles®
15693, DS-PP15/45 REV C4.3
www.andersonpower.com - 43 -
All Data Subject To Change Without Notice
Powerpole®
- Tooling Information
SECTION 2
Powerpole® Tooling
#16 / 20 1.3 / 0.52 262G1 262G2 1385519-1
#16 / 20 1.3 / 0.52 269G2 N/A 1385519-1
#12 / 16 3.3 / 1.3 261G1 261G4 1385520-1
#10 / 14 5.3 / 2.1 261G2 261G3 1385458-1
#12 / 16 3.3 / 1.3 269G1 N/A 1385520-1
#10 / 14 5.3 / 2.1 269G3 N/A 1385458-1
#10 / 14 5.3 / 2.1 200G1L 200G3L 1385460-1
#10 / 14 5.3 / 2.1 201G1H 201G3H 1385460-1
#10 / 14 5.3 / 2.1 1830G1 1830G2 1385460-1
TD0101
115V= TE0101
230V = TE0102
1725900-2
or
[354500-1]
1424266-1
or
[354578-1]
TD0102
AWG mm²
Reeled Part Numbers
Tin
Plating
Silver
Plating
APP
Applicator
ATS
Applicator
ATS
Press
Air Feed
Kit *
Wire Size Reeled Contact Crimp Tool
PP15 / 45 Flat Wiping Power & Ground
APP Press
NOTE: Insertion / Extraction tool for PP15/45 contacts = 111038G2
AWG mm²
Loose Piece Part Numbers
Tin
Plating
Silver
Plating
Hand
Tool Die Locator
Number
of Crimps
Wire Size
or
Pneumatic
Bench
Tool
Loose Piece Contact Crimp Tool
#16 / 20
#12 / 16
#16 / 20
#16 / 20
#12 / 16
#10 / 14
#12 / 16
#10 / 14
#10 / 14
#10 / 14
310 / 14
1.3 / 0.52 N/A 1332
3.3 / 1.3 N/A 1331
1.3 / 0.52 262G1-LPBK 262G2-LPBK
1.3 / 0.52 269G2-LPBK N/A
3.3 / 1.3 261G1-LPBK 261G4-LPBK
5.3 / 2.1 261G2-LPBK 261G3-LPBK
3.3 / 1.3 269G1-LPBK N/A
5.3 / 2.1 269G3-LPBK N/A
5.3 / 2.1 200G1L-LPBK 200G3L-LPBK
5.3 / 2.1 201G1H-LPBK 201G3H-LPBK
5.3 / 2.1 1830G1-LPBK 1830G2-LPBK
#8 8.4
1/0 53.5 1323G2
#1 42.4 1323G1
#2 33.6 1319
#4 21.2 1319G4
#6 13.3 1319G6
3/0 85 1328G2 1303G12
2/0 53.5 1328G1
1303G13
#1 42.4 1347
#6 13.3 1348 1387G1 1388G4 1389G3 Single
1. NOTE: See website for the most current information.
2. NOTE: Insertion / Extraction fool for PP15/45 contacts = 111038G2
Double
1309G2
or
1309G8
1367G1
N/A
1309G3
or
1309G8
1309G6
or
1309G8
Single
1387G1
1388G6
N/A SingleN/A
#6 13.3
1309G4
#10 / 12 5.3 / 3.3
N/A
N/A 1368
Series
1387G1
1387G2
1388G4
1389G4
1388G3
1304G32
1/0 53.5 1382
#2
N/A 1368
Series
Single
1388G7
33.6 1383
#4 21.1 1384
or
++
* All ATS applicators for APP® contacts are air feed style, (except 1385870) and require the press to have
an air feed kit installed. APP applicators are mechanical feed style and do not require an air feed kit.
PP180
PP120
PP75
PP15 / 45 Flat Wiping Power & Ground
1307
5900
1875G1
5952
1875G2
5953
5915
1875G3
1389G21
1389G6
1389G21
1389G6
1389G21
1389G6