19-3805; Rev 0; 8/06 KIT ATION EVALU E L B A AVAIL I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os Features The MAX7327, a 2-wire serial-interfaced peripheral, features 12 push-pull outputs and four configurable open-drain I/O ports with selectable internal pullups and transition detection. Ports are overvoltage protected to +6V, independent of supply voltage. The four I/O ports configured as inputs are continuously monitored for state changes (transition detection). State changes are indicated by the open-drain, +6V-tolerant INT output. The interrupt is latched, detecting transient changes. When the MAX7327 is subsequently accessed through the serial interface, any pending interrupt is cleared. The 12 push-pull and the four open-drain outputs are rated to sink 20mA, and are capable of driving LEDs. The RST input clears the serial interface, terminating any I2C* communication to or from the MAX7327. The MAX7327 uses two address inputs with four-level logic to allow 16 I 2 C slave addresses. The slave address also determines the power-up logic state for the I/O ports, and enables or disables internal 40k pullups in groups of two ports. 400kHz I2C Serial Interface +1.71V to +5.5V Operating Voltage 12 Push-Pull Output Ports, Rated at 20mA Sink Current 4 Open-Drain I/O Ports, Rated at 20mA Sink Current I/O Ports are Overvoltage Protected to +6V Selectable I/O Port Power-Up Default Logic States Transient Changes are Latched, Allowing Detection Between Read Operations INT Output Alerts Changes on Inputs AD0 and AD2 Inputs Select from 16 Slave Addresses Low 0.6A (typ) Standby Current -40C to +125C Temperature Range The MAX7327 is one device in a family of pin-compatible port expanders with a choice of input ports, open-drain I/O ports, and push-pull output ports (see Table 1). The MAX7327 is available in the 24-pin QSOP and TQFN packages, and is specified over the -40C to +125C automotive temperature range. Applications Cell Phones SAN/NAS Notebooks Satellite Radio Servers Automotive Ordering Information PART TEMP RANGE PIN-PACKAGE MAX7327AEG+ -40C to +125C 24 QSOP MAX7327ATG+ -40C to +125C MAX7327AATG+ -40C to +125C AD0 O15 O14 O13 O12 O11 17 16 15 14 13 T2444-3 24 TQFN-EP** T243A3-1 (3.5mm x 3.5mm) Selector Guide PART 18 E24-1 +Denotes lead-free package. **EP = Exposed pad. Pin Configurations TOP VIEW 24 TQFN-EP** (4mm x 4mm) PKG CODE INPUTS INTERRUPT MASK OPENPUSH-PULL DRAIN OUTPUTS OUTPUTS MAX7324 8 Yes -- 8 SCL 19 12 O10 MAX7325 Up to 8 -- Up to 8 8 SDA 20 11 O9 MAX7326 4 Yes -- 12 10 O8 MAX7327 Up to 4 -- Up to 4 12 V+ 21 MAX7327 INT 22 RST 23 EXPOSED PADDLE 2 3 4 5 6 O1 P2 P3 P4 P5 + 1 O0 AD2 24 9 GND 8 O7 7 O6 TQFN (4mm x 4mm) Pin Configurations continued at end of data sheet. Typical Application Circuit and Functional Diagram appear at end of data sheet. *Purchase of I2C components from Maxim Integrated Products, Inc., or one of its sublicensed Associated Companies, conveys a license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX7327 General Description MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os ABSOLUTE MAXIMUM RATINGS (All voltages referenced to GND.) Supply Voltage V+....................................................-0.3V to +6V SCL, SDA, AD0, AD2, RST, INT, P2-P5 ..................-0.3V to +6V O0, O1, O6-O15 .............................................-0.3V to V+ + 0.3V O0, O1, O6-O15 Output Current .....................................25mA P2-P5 Sink Current ............................................................25mA SDA Sink Current ...............................................................10mA INT Sink Current .................................................................10mA Total V+ Current .................................................................50mA Total GND Current ...........................................................100mA Continuous Power Dissipation (TA = +70C) 24-Pin QSOP (derate 9.5mW/C over +70C)...........761.9mW 24-Pin TQFN (derate 20.8mW/C over +70C) .......1666.7mW Operating Temperature Range .........................-40C to +125C Junction Temperature ......................................................+150C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS (V+ = +1.71V to +5.5V, TA = -40C to +125C, unless otherwise noted. Typical values are at V+ = +3.3V, TA = +25C.) (Note 1) PARAMETER Operating Supply Voltage SYMBOL V+ CONDITIONS TA = -40C to +125C MIN TYP 1.71 MAX UNITS 5.50 V 1.6 V Power-On Reset Voltage VPOR V+ falling Standby Current (Interface Idle) ISTB SCL and SDA and other digital inputs at V+ TA = -40C to +125C 0.6 1.9 A fSCL = 400kHz; other digital inputs at V+ TA = -40C to +125C 23 55 A Supply Current (Interface Running) I+ Input High-Voltage SDA, SCL, AD0, AD2, RST, P2-P5 VIH Input Low-Voltage SDA, SCL, AD0, AD2, RST, P2-P5 VIL Input Leakage Current SDA, SCL, AD0, AD2, RST, P2-P5 IIH, IIL V+ < 1.8V 0.8 x V+ V+ 1.8 V 0.7 x V+ V+ < 1.8V 0.2 x V+ V+ 1.8 V 0.3 x V+ SDA, SCL, AD0, AD2, RST, P0-P7 at V+ or GND, internal pullup disabled -0.2 Input Capacitance SDA, SCL, AD0, AD2, RST, P2-P5 Output Low Voltage O8-O15, P0, P7 +0.2 10 VOL 90 180 V+ = 1.71V, ISINK = 5mA (TQFN) 90 230 V+ = 2.5V, ISINK = 10mA (QSOP) 110 210 V+ = 2.5V, ISINK = 10mA (TQFN) 110 260 V+ = 3.3V, ISINK = 15mA (QSOP) 130 230 V+ = 3.3V, ISINK = 15mA (TQFN) 130 280 V+ = 5V, ISINK = 20mA (QSOP) 140 250 V+ = 5V, ISINK = 20mA (TQFN) 140 300 V+ = +1.71V, ISOURCE = 2mA V+ - 250 V+ - 30 V+ = +2.5V, ISOURCE = 5mA V+ - 360 V+ - 70 V+ = +3.3V, ISOURCE = 5mA V+ - 260 V+ - 100 V+ = +5V, ISOURCE = 10mA V+ - 360 V+ - 120 VOH Output Low-Voltage SDA VOLSDA ISINK = 6mA Output Low-Voltage INT VOLINT ISINK = 5mA Port Input Pullup Resistor RPU 25 V A pF V+ = 1.71V, ISINK = 5mA (QSOP) Output High Voltage O0, O1, O6-O15, P2-P5 2 V mV mV 250 mV 130 250 mV 40 55 k _______________________________________________________________________________________ I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os (V+ = +1.71V to +5.5V, TA = -40C to +125C, unless otherwise noted. Typical values are at V+ = +3.3V, TA = +25C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 4 s Port Output Data Valid tPPV CL 100pF Port Input Setup Time tPSU CL 100pF 0 s Port Input Hold Time tPH CL 100pF 4 s INT Input Data Valid Time tIV CL 100pF 4 s INT Reset Delay Time from STOP tIP CL 100pF 4 s INT Reset Delay Time from Acknowledge tIR CL 100pF 4 s TIMING CHARACTERISTICS (V+ = +1.71V to +5.5V, TA = -40C to +125C, unless otherwise noted. Typical values are at V+ = +3.3V, TA = +25C.) (Note 1) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 400 kHz Serial-Clock Frequency fSCL Bus Free Time Between a STOP and a START Condition tBUF 1.3 s Hold Time (Repeated) START Condition tHD, STA 0.6 s Repeated START Condition Setup Time tSU, STA 0.6 s STOP Condition Setup Time tSU, STO Data Hold Time tHD, DAT Data Setup Time tSU, DAT 100 ns tLOW tHIGH 1.3 0.7 s s SCL Clock Low Period SCL Clock High Period 0.6 s (Note 2) 0.9 s Rise Time of Both SDA and SCL Signals, Receiving tR (Notes 3, 4) 20 + 0.1Cb 300 ns Fall Time of Both SDA and SCL Signals, Receiving tF (Notes 3, 4) 20 + 0.1Cb 300 ns tF,TX (Notes 3, 4) 20 + 0.1Cb 250 ns Fall Time of SDA Transmitting Pulse Width of Spike Suppressed tSP (Note 5) Capacitive Load for Each Bus Line Cb (Note 3) RST Pulse Width tW 500 ns tRST 1 s RST Rising to START Condition Setup Time 50 ns 400 pF Note 1: All parameters tested at TA = +25C. Specifications over temperature are guaranteed by design. Note 2: A master device must provide a hold time of at least 300ns for the SDA signal (referred to VIL of the SCL signal) in order to bridge the undefined region of SCL's falling edge. Note 3: Guaranteed by design. Note 4: Cb = total capacitance of one bus line in pF. tR and tF measured between 0.3 x V+ and 0.7 x V+ with ISINK 6mA. Note 5: Input filters on the SDA and SCL inputs suppress noise spikes less than 50ns. _______________________________________________________________________________________ 3 MAX7327 PORT AND INTERRUPT INT TIMING CHARACTERISTICS Typical Operating Characteristics (TA = +25C, unless otherwise noted.) STANDBY CURRENT vs. TEMPERATURE 1.4 1.2 V+ = +5.0V 1.0 V+ = +3.3V V+ = +2.5V 0.8 0.6 0.4 40 30 V+ = +3.3V 20 V+ = +2.5V V+ = +1.71V 10 V+ = +1.71V 0.2 V+ = +5.0V 0 MAX7327 toc02 fSCL = 400kHz 50 0 -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (C) -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (C) OUTPUT VOLTAGE LOW vs. TEMPERATURE OUTPUT VOLTAGE HIGH vs. TEMPERATURE 0.20 V+ = +3.3V ISINK = 15mA 0.15 0.10 V+ = +2.5V ISINK = 10mA 0.05 V+ = +1.71V ISINK = 5mA 6 V+ = +1.62V ISINK = 4mA V+ = +5.0V ISOURCE = 10mA 5 OUTPUT VOLTAGE HIGH (V) V+ = +5.0V ISINK = 20mA MAX7327 toc03 0.25 4 MAX7327 toc04 STANDBY CURRENT (A) 1.6 60 SUPPLY CURRENT (A) fSCL = 0kHz 1.8 SUPPLY CURRENT vs. TEMPERATURE MAX7327 toc01 2.0 OUTPUT VOLTAGE LOW (V) MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os V+ = +3.3V ISOURCE = 5mA 3 V+ = +2.5V ISOURCE = 5mA V+ = +1.71V ISOURCE = 2mA 2 1 0 0 -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (C) -40 -25 -10 5 20 35 50 65 80 95 110 125 TEMPERATURE (C) Pin Description PIN NAME FUNCTION QSOP TQFN 1 22 INT Active-Low Interrupt Output. INT is an open-drain output. 2 23 RST Active-Low Reset Input. Drive RST low to clear the 2-wire interface. 3, 21 24, 18 AD2, AD0 4, 5, 10, 11, 13-20 1, 2, 7, 8, 10-17 O0, O1, O6-O15 6-9 3-6 P2-P5 12 9 GND Ground 22 19 SCL I2C-Compatible Serial Clock Input 23 20 SDA I2C-Compatible Serial Data I/O 24 21 V+ Positive Supply Voltage. Bypass V+ to GND with a 0.047F ceramic capacitor. -- EP EP Exposed Pad. Connect exposed pad to GND. 4 Address Inputs. Select device slave address with AD0 and AD2. Connect AD0 and AD2 to either GND, V+, SCL, or SDA to give four logic combinations (see Tables 2 and 3). Output Ports. O0, O1, O6-O15 are push-pull outputs rated at 20mA. P2-P5 Open-Drain I/Os _______________________________________________________________________________________ I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os MAX7319-MAX7329 Family Comparison The MAX7324-MAX7327 family consists of four pincompatible, 16-port expanders that integrate the functions of the MAX7320 and one of either the MAX7319, MAX7321, MAX7322, or MAX7323. Functional Overview The MAX7327 is a general-purpose port expander operating from a +1.71V to +5.5V supply that provides 12 push-pull output ports with a 20mA sink, 10mA source drive capability, and four open-drain I/O ports with a 20mA sink capability. The four open-drain outputs are overvoltage protected to +6V. The MAX7327 is set to two of 32 I2C slave addresses (see Tables 2 and 3) using address inputs AD2 and AD0, and is accessed over an I2C serial interface up to 400kHz. Eight push-pull outputs use a different slave address from the other four push-pull outputs and the open-drain I/Os. The eight push-pull outputs, O8-O15, use the 101xxxx addresses while the four outputs O0, O1, O6, and O7 and the open-drain I/Os P2-P5 use addresses with 110xxxx. The RST input clears the serial interface in case of a bus lockup, terminating any serial transaction to or from the MAX7327. Any of the four open-drain ports can be configured as a logic input by setting the port output logic-high (logichigh for an open-drain output is high impedance). When the MAX7327 is read through the serial interface, the actual logic levels at the ports are read back. Table 1. MAX7319-MAX7329 Family Comparison PART INPUT I2C SLAVE INPUTS INTERRUPT ADDRESS MASK OPENDRAIN OUTPUTS PUSHPULL OUTPUTS CONFIGURATION 16-PORT EXPANDERS 8 inputs and 8 push-pull outputs version: 8 input ports with programmable latching transition detection interrupt and selectable pullups. 8 MAX7324 Yes -- 8 8 push-pull outputs with selectable default logic levels. Offers maximum versatility for automatic input monitoring. An interrupt mask selects which inputs cause an interrupt on transitions, and transition flags identify which inputs have changed (even if only for a transient) since the ports were last read. 8 I/O and 8 push-pull outputs version: 8 open-drain I/O ports with latching transition detection interrupt and selectable pullups. 101xxxx and 110xxxx 8 push-pull outputs with selectable default logic levels. MAX7325 Up to 8 -- Up to 8 8 Open-drain outputs can level shift the logic-high state to a higher or lower voltage than V+ using external pullup resistors, but pullups draw current when output is low. Any open-drain port can be used as an input by setting the open-drain output to logichigh. Transition flags identify which open-drain port inputs have changed (even if only for a transient) since the ports were last read. _______________________________________________________________________________________ 5 MAX7327 Detailed Description MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os Table 1. MAX7319-MAX7329 Family Comparison (continued) PART INPUT I2C SLAVE INPUTS INTERRUPT ADDRESS MASK OPENDRAIN OUTPUTS PUSHPULL OUTPUTS CONFIGURATION 4 input-only, 12 push-pull output versions: 4 input ports with programmable latching transition detection interrupt and selectable pullups. 4 MAX7326 Yes -- 12 12 push-pull outputs with selectable default logic levels. Offers maximum versatility for automatic input monitoring. An interrupt mask selects which inputs cause an interrupt on transitions, and transition flags identify which inputs have changed (even if only for a transient) since the ports were last read. 4 I/O, 12 push-pull output versions: 4 open-drain I/O ports with latching transition detection interrupt and selectable pullups. 101xxxx and 110xxxx 12 push-pull outputs with selectable default logic levels. MAX7327 Up to 4 -- Up to 4 12 Open-drain outputs can level shift the logic-high state to a higher or lower voltage than V+ using external pullup resistors, but pullups draw current when output is low. Any open-drain port can be used as an input by setting the open-drain output to logichigh. Transition flags identify which open-drain port inputs have changed (even if only for a transient) since the ports were last read. 8-PORT EXPANDERS MAX7319 110xxxx 8 Yes -- -- Input-only versions: 8 input ports with programmable latching transition detection interrupt and selectable pullups. MAX7320 101xxxx -- -- -- 8 Output-only versions: 8 push-pull outputs with selectable power-up default levels. MAX7321 110xxxx Up to 8 -- Up to 8 -- I/O versions: 8 open-drain I/O ports with latching transition detection interrupt and selectable pullups. 4 4 input-only, 4 output-only versions: 4 input ports with programmable latching transition detection interrupt and selectable pullups. 4 push-pull outputs with selectable power-up default levels. MAX7322 6 110xxxx 4 Yes -- _______________________________________________________________________________________ I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os PART I2C INPUT SLAVE INPUTS INTERRUPT ADDRESS MASK OPENDRAIN OUTPUTS PUSHPULL OUTPUTS CONFIGURATION MAX7323 110xxxx Up to 4 -- Up to 4 4 4 I/O, 4 output-only versions: 4 open-drain I/O ports with latching transition detection interrupt and selectable pullups. 4 push-pull outputs with selectable power-up default levels. MAX7328 MAX7329 0100xxx 0111xxx Up to 8 -- Up to 8 -- PCF8574-, PCF8574A-compatible versions: 8 open-drain I/O ports with nonlatching transition detection interrupt and pullups on all ports. The four open-drain ports offer latching transition detection functionality when used as inputs. All input ports are continuously monitored for changes. An input change sets 1 of 4 flag bits that identify the changed input(s). All flags are cleared upon a subsequent read or write transaction to the MAX7327. A latching interrupt output INT automatically flags data changes on any of the I/O ports used as inputs through an interrupt mask register. Data changes on any input port forces INT to a logic-low. The interrupt output INT is deasserted when the MAX7327 is next accessed through the serial interface. Internal pullup resistors to V+ are selected by the address select inputs, AD0 and AD2. Pullups are enabled on the input ports in groups of two (see Table 2). Use the slave address selection to ensure that I/O ports used as inputs are logic-high on power-up. I/O ports with internal pullups enabled default to a logic-high output state. I/O ports with internal pullups disabled default to a logic-low output state. Output port power-up logic levels are selected by the address select inputs AD0 and AD2. Ports default to logic-high or logic-low on power-up in groups of two (see Tables 2 and 3). Initial Power-Up On power-up, the default states of the 12 push-pull output ports and the four open-drain I/O ports are set according to the I2C slave address selection inputs, AD0 and AD2 (see Tables 2 and 3). For I/O ports used as inputs, ensure that the default states are logic-high; therefore, the I/O ports power up in the high-impedance state. All I/O ports configured with pullups enabled also have a logic-high default state. On power- MAX7327 Table 1. MAX7319-MAX7329 Family Comparison (continued) up, the transition detection logic is reset, and INT is deasserted. The transition flags are cleared, indicating no data changes. Power-On Reset (POR) The MAX7327 contains an integral POR circuit that ensures all registers are reset to a known state on power-up. When V+ rises above VPOR (1.6V max), the POR circuit releases the registers and 2-wire interface for normal operation. When V+ drops to less than VPOR, the MAX7327 resets all register contents to the POR defaults (Tables 2 and 3). RST Input The active-low RST input operates as a hardware reset that voids any I2C transaction involving the MAX7327, forcing the MAX7327 into the I2C STOP condition. A reset does not affect the interrupt output (INT). Standby Mode When the serial interface is idle, the MAX7327 automatically enters standby mode drawing minimal supply current. Slave Address, Power-Up Default Logic Levels, and Input Pullup Selection Address inputs AD0 and AD2 determine the MAX7327 slave address and select which inputs have pullup resistors. Pullups are enabled on the input ports in groups of two (see Table 2). The MAX7327 slave address is determined on each I2C transmission, regardless of whether the transmission is actually addressing the MAX7327. The MAX7327 distinguishes whether address inputs AD0 and AD2 are connected to SDA or SCL instead of fixed-logic levels V+ or GND during the transmission. The MAX7327 slave _______________________________________________________________________________________ 7 address can be configured dynamically in the application without cycling the device supply. pullups and sets the default logic state to low. The pullup configuration is correct on power-up for a standard I2C configuration, where SDA or SCL are pulled up to V+ by the external I2C pullup resistors. There are circumstances where the assumption that SDA = SCL = V+ on power-up is not true; for example, in applications in which there is legitimate bus activity during power-up. If SDA and SCL are terminated with pullup resistors to a different supply voltage to the MAX7327's supply voltage, and if that pullup supply rises later than the MAX7327's supply, then SDA or SCL may appear at power-up to be connected to GND. In such applications, use the four address combinations that are selected by connecting address inputs AD0 and AD2 to V+ or GND (shown in bold in Tables 2 and 3). These selections are guaranteed to be correct at power-up, independent of SDA and SCL behavior. If one of the other 12 address combinations is used, an unexpected combination of pullups might be asserted until the first I2C transmission (to any device, not necessarily the MAX7327) is put on the bus. On initial power-up, the MAX7327 cannot decode the address inputs AD0 and AD2 fully until the first I2C transmission. AD0 and AD2 initially appear to be connected to V+ or GND. This is important because the address selection is used to determine the power-up default states of the output ports, I/O port initial logic state, and whether pullups are enabled. At power-up, the I 2 C SDA and SCL bus interface lines are high impedance at the I/O pins of every device (master or slave) connected to the bus, including the MAX7327. This is guaranteed as part of the I 2C specification. Therefore, when address inputs AD0 and AD2 are connected to SDA or SCL during power-up, they appear to be connected to V+. The pullup selection logic uses AD0 to select whether pullups are enabled for ports P2 and P3, and uses AD2 to select whether pullups are enabled for ports P4 and P5. The rule is that a logichigh, SDA, or SCL connection selects the pullups and sets the logic state to high. A logic-low deselects the Table 2. MAX7327 Address Map for Outputs O0, O1, O6, O7, and Ports P2-P5 SCL SCL SCL SCL SDA SDA SDA SDA GND GND GND GND V+ V+ V+ V+ 8 GND V+ SCL SDA GND V+ SCL SDA GND V+ SCL SDA GND V+ SCL SDA DEVICE ADDRESS A6 A5 A4 A3 A2 A1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 PORTS POWER-UP DEFAULT A0 O7 O6 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 P5 P4 P3 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 40k INPUT PULLUPS ENABLED P2 O1 O0 O7 O6 P5 P4 P3 P2 O1 O0 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 Y Y Y Y Y Y Y Y -- -- -- -- Y Y Y Y Y Y Y Y Y Y Y Y -- -- -- -- Y Y Y Y _______________________________________________________________________________________ -- Y Y Y -- Y Y Y -- Y Y Y -- Y Y Y -- Y Y Y -- Y Y Y -- Y Y Y -- Y Y Y Pullups are not enabled for push-pull outputs PIN CONNECTION AD2 AD0 Pullups are not enabled for push-pull outputs MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os PIN CONNECTION DEVICE ADDRESS MAX7327 Table 3. MAX7327 Address Map for Outputs O8-O15 OUTPUTS POWER-UP DEFAULT AD2 AD0 A6 A5 A4 A3 A2 A1 A0 O15 O14 O13 O12 O11 O10 O9 O8 SCL GND 1 0 1 0 0 0 0 1 1 1 1 0 0 0 0 SCL V+ 1 0 1 0 0 0 1 1 1 1 1 1 1 1 1 SCL SCL 1 0 1 0 0 1 0 1 1 1 1 1 1 1 1 SCL SDA 1 0 1 0 0 1 1 1 1 1 1 1 1 1 1 SDA GND 1 0 1 0 1 0 0 1 1 1 1 0 0 0 0 SDA V+ 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 SDA SCL 1 0 1 0 1 1 0 1 1 1 1 1 1 1 1 SDA SDA 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 GND GND 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 GND V+ 1 0 1 1 0 0 1 0 0 0 0 1 1 1 1 GND SCL 1 0 1 1 0 1 0 0 0 0 0 1 1 1 1 GND SDA 1 0 1 1 0 1 1 0 0 0 0 1 1 1 1 V+ GND 1 0 1 1 1 0 0 1 1 1 1 0 0 0 0 V+ V+ 1 0 1 1 1 0 1 1 1 1 1 1 1 1 1 V+ SCL 1 0 1 1 1 1 0 1 1 1 1 1 1 1 1 V+ SDA 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 I/O Port Inputs I/O port inputs switch at CMOS logic levels as determined by the expander's supply voltage, and are overvoltage tolerant to +6V, independent of the expander's supply voltage. I/O Port Input Transition Detection All I/O ports configured as inputs are monitored for changes since the expander was last accessed through the serial interface. The state of the ports is stored in an internal "snapshot" register for transition monitoring. The snapshot is continuously compared with the actual input conditions, and if a change is detected for any port input, INT is asserted to signal a state change. The input ports are sampled (internally latched into the snapshot register) and the old transition flags cleared during the I2C acknowledge of every MAX7327 read and write access. The previous port transition flags are read through the serial interface as the second byte of a 2-byte read sequence. A long read sequence (more than 2 bytes) can be used to poll the expander continuously without the overhead of resending the slave address. If more than 2 bytes are read from the expander, the expander repeatedly returns the 2 bytes of input port data followed by the transition flags. The inputs are repeatedly resampled and the transition flags repeatedly reset for each pair of bytes read. All changes that occur during a long read sequence are detected and reported. The INT output is not reasserted during a read sequence to avoid recursive reentry into an interrupt service routine. Instead, if a data change occurs that would normally cause the INT output to be set, the INT assertion is delayed until the STOP condition. INT is not reasserted upon a STOP condition if the changed input data is read before the STOP occurs. The INT logic ensures that unnecessary interrupts are not asserted, yet data changes are detected and reported no matter when the change occurs. _______________________________________________________________________________________ 9 MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os Serial Interface Serial Addressing The MAX7327 operates as a slave that sends and receives data through an I2C interface. The interface uses a serial-data line (SDA) and a serial-clock line (SCL) to achieve bidirectional communication between master(s) and slave(s). The master initiates all data transfers to and from the MAX7327 and generates the SCL clock that synchronizes the data transfer (Figure 1). SDA operates as both an input and an open-drain output. A pullup resistor, typically 4.7k, is required on SDA. SCL operates only as an input. A pullup resistor, typically 4.7k, is required on SCL if there are multiple masters on the 2-wire interface, or if the master in a single-master system has an open-drain SCL output. Each transmission consists of a START condition sent by a master, followed by the MAX7327's 7-bit slave addresses plus R/W bits, one or more data bytes, and finally a STOP condition (Figure 2). START and STOP Conditions Both SCL and SDA remain high when the interface is not busy. A master signals the beginning of a transmission with a START (S) condition by transitioning SDA from high to low while SCL is high. When the master has finished communicating with the slave, the master issues a STOP (P) condition by transitioning SDA from low to high while SCL is high. The bus is then free for another transmission (Figure 2). Bit Transfer One data bit is transferred during each clock pulse. The data on SDA must remain stable while SCL is high (Figure 3). SDA tBUF tSU,STA tSU,DAT tLOW tHD,STA tSU,STO tHD,DAT tHIGH SCL tHD,STA tR tF START CONDITION REPEATED START CONDITION STOP CONDITION Figure 1. 2-Wire Serial Interface Timing Details SDA SDA SCL SCL S P START CONDITION STOP CONDITION Figure 2. START and STOP Conditions 10 DATA LINE STABLE; CHANGE OF DATA DATA VALID ALLOWED Figure 3. Bit Transfer ______________________________________________________________________________________ START CONDITION I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os Accessing the MAX7327 The MAX7327 is a combination of MAX7320 and MAX7323. The group A of eight ports (O0, O1, P2-P5, O6, and O7) corresponding to those of the MAX7323 and the group B of eight ports (O8-O15) corresponding to those of the MAX7320 are read/write separately through their own addresses as shown by Tables 2 and 3, respectively. A single-byte read from the group A ports of the MAX7327 returns the status of the four I/O ports and the four output ports (read back as inputs), and clear both the internal transition flags and the INT output when the master acknowledges the slave address byte. A 2-byte read from the group A ports of the MAX7327 returns the status of the four I/O ports and the four output ports (as for a single byte read), followed by the four transition flags for the four I/O ports. The internal transition flags and the INT output are cleared automatically when the master acknowledges the slave address byte (but the previous transition flag data is sent as the second byte). A multibyte read (more than 2 bytes before the I2C STOP bit) from the group A ports of the MAX7327 repeatedly returns the port data, alternating with the transition flags. As the port data is resampled for each transmission, and the transition flags are reset each time, a multibyte read continuously returns the current data and identifies any changing I/O ports. If a port input data change occurs during the read sequence, then INT is reasserted during the I2C STOP bit. The MAX7327 does not generate another interrupt during a single-byte or multibyte MAX7327 read routine. Input port data is sampled during the preceding I2C acknowledge bit (the acknowledge bit for the I2C slave address in the case of a single-byte or 2-byte read). Slave Address The MAX7327 has two different 7-bit slave addresses (Figure 5). The addresses are different to communicate to the eight push-pull outputs, O8-O15, or the other eight I/Os. The eighth bit following the 7-bit slave address is the R/W bit. It is low for a write command, and high for a read command. The first (A6), second (A5), and third (A4) bits of the MAX7327 slave address are always 1, 1, and 0 (O0, O1, P2-P5, O6, O7) or 1, 0, and 1 (O8-O15). Connect AD0 and AD2 to GND, V+, SDA, or SCL to select slave address bits A3, A2, A1, and A0. The MAX7327 has 16 possible slave addresses (Tables 2 and 3), allowing up to 16 MAX7327 devices on an I2C bus. CLOCK PULSE FOR ACKNOWLEDGEMENT START CONDITION SCL 1 2 8 9 SDA BY TRANSMITTER SDA BY RECEIVER S Figure 4. Acknowledge SDA 1 A5 A4 A3 A2 A1 A0 R/W ACK LSB MSB SCL Figure 5. Slave Address ______________________________________________________________________________________ 11 MAX7327 Acknowledge The acknowledge bit is a clocked 9th bit the recipient uses to acknowledge receipt of each byte of data (Figure 4). Each byte transferred effectively requires 9 bits. The master generates the 9th clock pulse, and the recipient pulls down SDA during the acknowledge clock pulse, such that the SDA line is stable low during the high period of the clock pulse. When the master is transmitting to the MAX7327, the MAX7327 generates the acknowledge bit because the device is the recipient. When the MAX7327 is transmitting to the master, the master generates the acknowledge bit because the master is the recipient. MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os Reading the MAX7327 A read from the group A ports of the MAX7327 starts with the master transmitting the port group's slave address with the R/W bit set to high. The MAX7327 acknowledges the slave address, and samples the status of the ports during the acknowledge bit. INT goes high during the slave address acknowledge. The master can then issue a STOP condition after the acknowledge. The snapshot is taken, and the INT status remains unchanged, if the master terminates the serial transition with a no-acknowledge. When the master reads one byte from the group A ports of the MAX7327 and subsequently issues a STOP condition (Figure 6), the MAX7327 transmits the current port data, clears the change flags, and resets the tran- A single-byte read from the group B ports of the MAX7327 returns the status of the eight output ports, read back as inputs. A 2-byte read from the group B ports of the MAX7327 repeatedly returns the status of the eight output ports, read back as inputs. A multibyte read (more than 2 bytes before the I2C STOP bit) from the group B ports of the MAX7327 repeatedly returns the status of the eight output ports, read back as inputs. A single-byte write to the group A or B ports of the MAX7327 sets the logic state of all eight ports. A multibyte write to the group A or B ports of the MAX7327 repeatedly sets the logic state of all eight ports. O7 O6 P5 P4 P3 P2 O1 O0 NO ACKNOWLEDGE FROM MASTER ACKNOWLEDGE FROM MAX7327 S MAX7327 SLAVE ADDRESS 1 R/W A D7 D6 D5 PORT SNAPSHOT D4 D3 D2 D1 D0 N P PORT SNAPSHOT SCL tPH PORTS tIV tPS tIR INT OUTPUT INT REMAINS HIGH UNTIL STOP CONDITION Figure 6. Reading Group A Ports of the MAX7327 (1 Data Byte) 12 ______________________________________________________________________________________ tIP I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os A read from the group B ports of the MAX7327 starts with the master transmitting the group's slave address with the R/W bit set high. The MAX7327 acknowledges the slave address, and samples the logic state of the output ports during the acknowledge bit. The master can read one or more bytes from the group B ports of the MAX7327 and then issues a STOP condition (Figure 8). The MAX7327 transmits the current port data, read back from the actual port outputs (not the port output latches) during the acknowledge. If a port is forced to a logic state other than its programmed state, the readback reflects this. If driving a capacitive load, the readback port level verification algorithms may need to take the RC rise/fall time into account. Typically, the master reads one byte from the group B ports of the MAX7327, then issues a STOP condition (Figure 8). However, the master can read two or more FLAG O7 O6 P5 P4 P3 P2 O1 O0 F6 F5 F4 F3 F2 F1 F0 NO ACKNOWLEDGE FROM MASTER D7 D6 D5 D4 D3 D2 D1 D0 N F7 ACKNOWLEDGE FROM MAX7327 S MAX7327 SLAVE ADDRESS 1 A D7 R/W D6 D5 D4 PORT SNAPSHOT D3 D2 D1 D0 A P PORT SNAPSHOT PORT SNAPSHOT SCL tPH PORTS tPS tIV tIR INT OUTPUT tIP INT REMAINS HIGH UNTIL STOP CONDITION Figure 7. Reading Group A Ports of the MAX7327 (2 Data Bytes) P7 PORT SNAPSHOT DATA P6 P5 P4 P3 DATA 1 P2 P1 P0 ACKNOWLEDGE FROM MAX7327 S MAX7327 SLAVE ADDRESS 1 R/W A D7 D6 D5 D4 PORT SNAPSHOT TAKEN D3 D2 D1 D0 PORT SNAPSHOT TAKEN A P ACKNOWLEDGE FROM MASTER SCL Figure 8. Reading Group B Ports of MAX7327 ______________________________________________________________________________________ 13 MAX7327 sition detection. INT deasserts during the slave acknowledge. The new snapshot data is the current port data transmitted to the master, and therefore, port changes occuring during the transmission are detected. INT remains high until the STOP condition. When the master reads 2 bytes from the group A ports of the MAX7327 and subsequently issues a STOP condition (Figure 7), the MAX7327 transmits the current port data, followed by the change flags. The change flags are then cleared, and transition detection is reset. INT goes high (high impedance if an external pullup resistor is not fitted) during the slave acknowledge. The new snapshot data is the current port data transmitted to the master, and therefore, port changes occuring during the transmission are detected. INT remains high until the STOP condition. MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os bytes from the group B ports of the MAX7327, then issues a STOP condition. In this case, the MAX7327 resamples the port outputs during each acknowledge and transmits the new data each time. Writing to the MAX7327 A write to the group A or B ports of the MAX7327 starts with the master transmitting the group's slave address with the R/W bit set low. The MAX7327 acknowledges the slave address, and samples the ports during the acknowledge bit. INT goes high (high impedance if an external pullup resistor is not fitted) during the slave acknowledge only when it writes to the group A ports. The master can now transmit one or more bytes of data. The MAX7327 acknowledges these subsequent bytes of data and updates the corresponding group's ports with each new byte until the master issues a STOP condition (Figure 9). Applications Information Port Input and I2C Interface Level Translation from Higher or Lower Logic Voltages The MAX7327's SDA, SCL, AD0, AD2, RST, INT, and the four I/O ports P2-P5 are overvoltage protected to +6V, independent of V+. This allows the MAX7327 to operate from a lower supply voltage, such as +3.3V, while the I2C interface and/or some of the four I/O ports are driven from a higher logic level, such as +5V. The MAX7327 can operate from a higher supply voltage, such as +3V, while the I2C interface and/or some 1 SCL 2 3 4 5 6 7 S START CONDITION Port Output Signal Level Translation The open-drain output architecture allows for level translation to higher or lower voltages than the MAX7327's supply. Use an external pullup resistor on any output to convert the high-impedance logic-high condition to a positive voltage level. The resistor can be connected to any voltage up to +6V, and the resistor value chosen to ensure no more than 20mA to be sunk in logic-low condition. For interfacing CMOS inputs, a pullup resistor value of 220k is a good starting point. Use a lower resistance to improve noise immunity, in applications where power consumption is less critical, or where a faster rise time is needed for a given capacitive load. Each of the 12 push-pull output ports has protection diodes to V+ and GND. When a port output is driven to a voltage higher than V+ or lower than GND, the appropriate protection diode clamps the output to a diode drop above V+ or below GND. When the MAX7327 is powered down (V+ = 0V), every output port's protection 8 DATA TO PORT SLAVE ADDRESS SDA of the four I/O ports P2-P5 are driven from a lower logic level, such as +2.5V. For V+ < 1.8V, apply a minimum voltage of 0.8 x V+ to assert a logic-high on any input. For a V+ 1.8V, apply a voltage of 0.7 x V+ to assert a logic-high. For example, a MAX7327 operating from a +5V supply may not recognize a +3.3V nominal logichigh. One solution for input-level translation is to drive MAX7327 inputs from open-drain outputs. Use a pullup resistor to V+ or a higher supply to ensure a high logic voltage greater than 0.7 x V+. 0 A DATA TO PORT DATA 1 A DATA 2 A ACKNOWLEDGE FROM SLAVE R/W ACKNOWLEDGE FROM SLAVE ACKNOWLEDGE FROM SLAVE WRITE TO PORT DATA OUT FROM PORT DATA 1 VALID tPV DATA 2 VALID tPV Figure 9. Writing the MAX7327 14 ______________________________________________________________________________________ I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os VOL is the output low voltage of the MAX7327 when sinking ILED (V). Each of the four I/O ports P2-P5 has a protection diode to GND (Figure 11). When a port output is driven to a voltage lower than GND, the protection diode clamps the output to a diode drop below GND. Each of the four I/O ports P2-P5 also has a 40k (typ) pullup resistor that can be enabled or disabled. When a port input is driven to a voltage higher than V+, the body diode of the pullup enable switch conducts and the 40k pullup resistor is enabled. When the MAX7327 is powered down (V+ = 0V), each I/O port appears as a 40k resistor in series with a diode connected to 0V. Input ports are protected to +6V under any of these circumstances (Figure 11). ILED is the desired operating current of the LED (A). Driving LED Loads When driving LEDs from one of the 12 push-pull outputs, a resistor must be fitted in series with the LED to limit the LED current to no more than 20mA. Connect the LED cathode to the MAX7327 port, and the LED anode to V+ through the series current-limiting resistor, RLED. Set the port output low to light the LED. Choose the resistor value according to the following formula: RLED = (VSUPPLY - VLED - VOL) / ILED where: RLED is the resistance of the resistor in series with the LED (). VSUPPLY is the supply voltage used to drive the LED (V). For example, to operate a 2.2V red LED at 10mA from a +5V supply: RLED = (5 - 2.2 - 0.1) / 0.01 = 270 Driving Load Currents Higher than 20mA The MAX7327 can be used to drive loads such as relays that draw more than 20mA by paralleling outputs. Use at least one output per 20mA of load current; for example, a 5V 330mW relay draws 66mA, and therefore, requires four paralleled outputs. Any combination of outputs can be used as part of a load-sharing design because any combination of ports can be set or cleared at the same time by writing to the MAX7327. Do not exceed a total sink current of 100mA for the device. The MAX7327 must be protected from the negative voltage transient generated when switching off inductive loads (such as relays), by connecting a reversebiased diode across the inductive load. Choose the peak current for the diode to be greater than the inductive load's operating current. Power-Supply Considerations The MAX7327 operates with a supply voltage of +1.71V to +5.5V. Bypass the supply to GND with a ceramic capacitor of at least 0.047F as close as possible to the device. For the TQFN version, additionally connect the exposed pad to GND. VLED is the forward voltage of the LED (V). V+ V+ V+ V+ MAX7327 MAX7327 O0-O2 O6-O15 PULLUP ENABLE 40k P2-P5 INPUT OUTPUT OUTPUT Figure 10. MAX7327 Push-Pull Output Port Structure Figure 11. MAX7327 Open-Drain I/O Port Structure ______________________________________________________________________________________ 15 MAX7327 diodes to V+ and GND continue to appear as a diode clamp from each output to GND (Figure 10). Functional Diagram Typical Application Circuit 3.3V V+ C AD0 AD2 SCL INPUT SDA FILTER I2C CONTROL I/O PORTS SCL SCL SDA SDA RST RST INT INT MAX7327 O15 O14 013 012 O11 O10 O9 O8 INT POWER-ON RESET RST O15 O14 O13 O12 O11 O10 O9 O8 O7 O6 P5 P4 P3 P2 O1 O0 MAX7327 AD0 AD2 GND Pin Configurations (continued) O7 O6 P5 P4 P3 P2 O2 O1 PROCESS: BiCMOS TOP VIEW INT 1 24 V+ RST 2 23 SDA AD2 3 O0 4 22 SCL MAX7327 21 AD0 O1 5 20 O15 P2 6 19 O14 P3 7 18 O13 P4 8 17 O12 P5 9 16 O11 O6 10 15 O10 O7 11 14 O9 GND 12 13 O8 QSOP 16 OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT INPUT/OUTPUT INPUT/OUTPUT INPUT/OUTPUT INPUT/OUTPUT OUTPUT OUTPUT Chip Information + MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os ______________________________________________________________________________________ I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os 24L QFN THIN.EPS PACKAGE OUTLINE, 12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm 21-0139 E 1 2 ______________________________________________________________________________________ 17 MAX7327 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) PACKAGE OUTLINE, 12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm 21-0139 18 ______________________________________________________________________________________ E 2 2 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os QSOP.EPS PACKAGE OUTLINE, QSOP .150", .025" LEAD PITCH 21-0055 F 1 1 ______________________________________________________________________________________ 19 MAX7327 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 24L THIN QFN.EPS MAX7327 I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os 20 ______________________________________________________________________________________ I2C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 21 (c) 2006 Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc. MAX7327 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) ENGLISH * ???? * ??? * ??? WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS MAX7327 Part Number Table Notes: 1. See the MAX7327 QuickView Data Sheet for further information on this product family or download the MAX7327 full data sheet (PDF, 344kB). 2. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales. 3. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day. 4. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: See full data sheet or Part Naming C onventions. 5. * Some packages have variations, listed on the drawing. "PkgC ode/Variation" tells which variation the product uses. Part Number Free Sample MAX7327AEG Buy Direct Package: TYPE PINS SIZE DRAWING CODE/VAR * QSOP;24 pin;.150" Dwg: 21-0055F (PDF) Use pkgcode/variation: E24-1* MAX7327AEG-T Temp RoHS/Lead-Free? Materials Analysis -40C to +125C RoHS/Lead-Free: No Materials Analysis -40C to +125C RoHS/Lead-Free: No MAX7327AATG+ THIN QFN;24 pin;3.5x3.5x.8mm Dwg: 21-0188A (PDF) Use pkgcode/variation: T243A3+1* -40C to +125C RoHS/Lead-Free: Yes Materials Analysis MAX7327AATG+T THIN QFN;24 pin;3.5x3.5x.8mm Dwg: 21-0188A (PDF) Use pkgcode/variation: T243A3+1* -40C to +125C RoHS/Lead-Free: Yes Materials Analysis MAX7327ATG THIN QFN;24 pin;4X4X0.8mm Dwg: 21-0139E (PDF) Use pkgcode/variation: T2444-4* -40C to +125C RoHS/Lead-Free: No Materials Analysis MAX7327ATG-T Didn't Find What You Need? -40C to +125C RoHS/Lead-Free: No C ONTAC T US: SEND US AN EMAIL C opyright 2 0 0 7 by M axim I ntegrated P roduc ts , Dallas Semic onduc tor * Legal N otic es * P rivac y P olic y