AK4384VTP - AKM Semiconductor, Inc.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 1 -

GENERAL DESCRIPTION

The AK4384 offers the perfect mix for cost and performance based audio systems. Using AKM's multi bit

architecture for its modulator the AK4384 delivers a wide dynamic range while preserving linearity for

improved THD+N performance. The AK4384 integrates a combination of SCF and CTF filters increasing

performance for systems with excessive clock jitter. The 24 Bit word length and 192kHz sampling rate

make this part ideal for a wide range of applications including DVD-Audio. The AK4384 is offered in a

space saving 16pin TSSOP package.

FEATURES

o Sampling Rate Ranging from 8kHz to 192kHz

o 128 times Oversampling (Normal Speed Mode)

o 64 times Oversampling (Double Speed Mode)

o 32 times Oversampling (Quad Speed Mode)

o 24-Bit 8 times FIR Digital Filter

o SCF with High Tolerance to Clock Jitter

o 2nd order Analog LPF

o Single Ended Output Buffer

o Digital de-emphasis for 32k, 44.1k and 48kHz sampling

o Soft mute

o Digital Attenuator (Linear 256 steps)

o I/F format: 24-Bit MSB justified, 24/20/16-Bit LSB justified or I2S

o Master clock: 256fs, 384fs, 512fs, 768fs or 1152fs (Normal Speed Mode)

128fs, 192fs, 256fs or 384fs (Double Speed Mode)

128fs, 192fs (Quad Speed Mode)

o THD+N: -94dB

o Dynamic Range: 106dB

o Power supply: 4.5 to 5.5V

o Very Small Package: 16pin TSSOP (6.4mm x 5.0mm)

LRCK

BICK

SDTI

Audio

Data

Interface

MCLK

PDN

∆Σ

Modulator

AOUTL

8X

Interpolator SCF

LPF

AOUTR

VDD

VSS

VCOM

De-emphasis

Control

P/S

µP

Interface

Clock

Divider

SMUTE/CSN

ACKS/CCLK

DIF0/CDTI

∆Σ

Modulator

8X

Interpolator

DZFR

DZFL

SCF

LPF

ATT

106dB 192kHz 24-Bit 2ch ∆Σ

DAC

AK4384

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 2 -

n Ordering Guide

AK4384VT -40 ∼ +85°C 16pin TSSOP (0.65mm pitch)

AKD4384 Evaluation Board for AK4384

n Pin Layout

1

MCLK

LRCK

BICK

SMUTE/CSN

ACKS/CCLK

DIF0/CDTI

Top

View

2

3

4

5

6

7

8

DZFL

DZFR

VSS

VDD

VCOM

AOUTL

AOUTR

P/S

16

15

14

13

12

11

10

9

PDN

SDTI

PIN/FUNCTION

No. Pin Name I/O Function

1 MCLK I Master Clock Input Pin

An external TTL clock should be input on this pin.

2 BICK I Audio Serial Data Clock Pin

3 SDTI I Audio Serial Data Input Pin

4 LRCK I L/R Clock Pin

5 PDN I Power-Down Mode Pin

When at “L”, the AK4384 is in the power-down mode and is held in reset. The

AK4384 should always be reset upon power-up.

SMUTE I Soft Mute Pin in parallel mode

“H”: Enable, “L”: Disable

6

CSN I Chip Select Pin in serial mode

ACKS I Auto Setting Mode Pin in parallel mode

“L”: Manual Setting Mode, “H”: Auto Setting Mode

7

CCLK I Control Data Clock Pin in serial mode

DIF0 I Audio Data Interface Format Pin in parallel mode 8 CDTI I Control Data Input Pin in serial mode

9 P/S I Parallel/Serial Select Pin (Internal pull-up pin)

“L”: Serial control mode, “H”: Parallel control mode

10 AOUTR O Rch Analog Output Pin

11 AOUTL O Lch Analog Output Pin

12 VCOM O Common Voltage Pin, VDD/2

Normally connected to VSS with a 0.1µF ceramic capacitor in parallel with a

10µF electrolytic cap.

13 VSS - Ground Pin

14 VDD - Power Supply Pin

15 DZFR O Rch Data Zero Input Detect Pin

16 DZFL O Lch Data Zero Input Detect Pin

Note: All input pins except pull-up pin should not be left floating.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 3 -

ABSOLUTE MAXIMUM RATINGS

(VSS=0V; Note 1)

Parameter Symbol min max Units

Power Supply VDD -0.3 6.0 V

Input Current (any pins except for supplies) IIN - ±10 mA

Input Voltage VIND -0.3 VDD+0.3 V

Ambient Operating Temperature Ta -40 85 °C

Storage Temperature Tstg -65 150 °C

Note: 1. All voltages with respect to ground.

WARNING: Operation at or beyond these limits may results in permanent damage to the device.

Normal operation is not guaranteed at these extremes.

RECOMMENDED OPERATING CONDITIONS

(VSS=0V; Note 1)

Parameter Symbol min typ max Units

Power Supply VDD 4.5 5.0 5.5 V

*AKM assumes no responsibility for the usage beyond the conditions in this datasheet.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 4 -

ANALOG CHARACTERISTICS

(Ta=25°C; VDD=5.0V; fs=44.1kHz; BICK=64fs; Signal Frequency=1kHz; 24bit Input Data;

Measurement frequency=20Hz ∼ 20kHz; RL ≥5kΩ; unless otherwise specified)

Parameter min typ max Units

Resolution 24 Bits

Dynamic Characteristics (Note 3)

fs=44.1kHz

BW=20kHz 0dBFS

-60dBFS -94

-42 -84

- dB

dB

fs=96kHz

BW=40kHz 0dBFS

-60dBFS -92

-39 -

- dB

dB

THD+N

fs=192kHz

BW=40kHz 0dBFS

-60dBFS -92

-39 -

- dB

dB

Dynamic Range (-60dBFS with A-weighted) (Note 4) 100 106 dB

S/N (A-weighted) (Note 5) 100 106 dB

Interchannel Isolation (1kHz) 90 100 dB

Interchannel Gain Mismatch 0.2 0.5 dB

DC Accuracy

Gain Drift 100 - ppm/°C

Output Voltage (Note 6) 3.15 3.40 3.65 Vpp

Load Resistance (Note 7) 5 kΩ

Power Supplies

Power Supply Current (VDD)

Normal Operation (PDN = “H”, fs≤96kHz)

Normal Operation (PDN = “H”, fs=192kHz)

Power-Down Mode (PDN = “L”) (Note 8)

17

20

10

27

32

100

mA

µA

Notes: 3. Measured by Audio Precision (System Two). Refer to the evaluation board manual.

4. 100dB at 16bit data.

5. S/N does not depend on input bit length.

6. Full-scale voltage (0dB). Output voltage scales with the voltage of VREF,

AOUT (typ.@0dB) = 3.4Vpp × VDD/5.

7. For AC-load.

8. All digital inputs including clock pins (MCLK, BICK and LRCK) are held VDD or VSS.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 5 -

SHARP ROLL-OFF FILTER CHARACTERISTICS

(Ta = 25°C; VDD = 4.5 ∼ 5.5V; fs = 44.1kHz; DEM = OFF; SLOW = “0”)

Parameter Symbol min typ max Units

Digital filter

Passband ±0.05dB (Note 9)

-6.0dB PB 0

-

22.05 20.0

- kHz

kHz

Stopband (Note 9) SB 24.1 kHz

Passband Ripple PR ± 0.02 dB

Stopband Attenuation SA 54 dB

Group Delay (Note 10) GD - 19.3 - 1/fs

Digital Filter + LPF

Frequency Response

20.0kHz

40.0kHz

80.0kHz

fs=44.1kHz

fs=96kHz

fs=192kHz

FR

-

± 0.03

-

dB

Notes: 9. The passband and stopband frequencies scale with fs(system sampling rate).

For example, PB=0.4535×fs (@±0.05dB), SB=0.546×fs.

10. The calculating delay time which occurred by digital filtering. This time is from setting the 16/24bit data

of both channels to input register to the output of analog signal.

SLOW ROLL-OFF FILTER CHARACTERISTICS

(Ta = 25°C; VDD = 4.5 ~ 5.5V; fs = 44.1kHz; DEM = OFF; SLOW = “1”)

Parameter Symbol min typ max Units

Digital Filter

Passband ±0.04dB (Note 11)

-3.0dB PB

0

-

18.2 8.1

- kHz

kHz

Stopband (Note 11) SB 39.2 kHz

Passband Ripple PR ± 0.005 dB

Stopband Attenuation SA 72 dB

Group Delay (Note 10) GD - 19.3 - 1/fs

Digital Filter + LPF

Frequency Response

20.0kHz

40.0kHz

80.0kHz

fs=44.kHz

fs=96kHz

fs=192kHz

FR

-

+0.02/-5

+0.02/-4

+0.02/-5

-

dB

Note: 11. The passband and stopband frequencies scale with fs.

For example, PB = 0.185×fs (@±0.04dB), SB = 0.888×fs.

DC CHARACTERISTICS

(Ta=25°C; VDD=4.5 ∼ 5.5V)

Parameter Symbol min typ max Units

High-Level Input Voltage

Low-Level Input Voltage VIH

VIL 2.2

- -

0.8 V

V

High-Level Output Voltage (Iout=-80µA)

Low-Level Output Voltage (Iout=80µA) VOH

VOL VDD-0.4

- - -

0.4 V

V

Input Leakage Current (No

te 12)

Iin - - ± 10 µA

Note: 12. P/S pin has internal pull-up device, normally 100kΩ.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 6 -

SWITCHING CHARACTERISTICS

(Ta=25°C; VDD=4.5 ∼ 5.5V; CL=20pF)

Parameter Symbol min typ max Units

Master Clock Frequency

Duty Cycle

fCLK

dCLK 2.048

40 11.2896

36.864

60 MHz

%

LRCK Frequency

Normal Speed Mode

Double Speed Mode

Quad Speed Mode

Duty Cycle

fsn

fsd

fsq

Duty

8

60

120

45

48

96

192

55

kHz

%

Audio Interface Timing

BICK Period

Normal Speed Mode

Double/Quad Speed Mode

BICK Pulse Width Low

Pulse Width High

BICK rising to LRCK Edge (Note 13)

LRCK Edge to BICK rising (Note 13)

SDTI Hold Time

SDTI Setup Time

tBCK

tBCKL

tBCKH

tBLR

tLRB

tSDH

tSDS

1/128fs

1/64fs

30

20

ns

Control Interface Timing

CCLK Period

CCLK Pulse Width Low

Pulse Width High

CDTI Setup Time

CDTI Hold Time

CSN “H” Time

CSN “↓” to CCLK “↑”

CCLK “↑” to CSN “↑”

tCCK

tCCKL

tCCKH

tCDS

tCDH

tCSW

tCSS

tCSH

200

80

40

150

50

ns

Reset Timing

PDN Pulse Width (Note 14)

tPD

150

ns

Notes: 13. BICK rising edge must not occur at the same time as LRCK edge.

14. The AK4384 can be reset by bringing PDN= “L”.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 7 -

n Timing Diagram

1/fCLK

tCLKL

VIH

tCLKH

MCLK VIL

dCLK=tCLKH x fCLK, tCLKL x fCLK

1/fs

VIH

LRCK VIL

tBCK

tBCKL

VIH

tBCKH

BICK VIL

Clock Timing

tLRB

LRCK

VIH

BICK VIL

tSDS

VIH

SDTI VIL

tSDH

VIH

VIL

tBLR

Serial Interface Timing

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 8 -

tCSS

CSN

VIH

CCLK VIL

VIH

CDTI VIL

VIH

VIL

C1 C0 R/W A4

tCCKL tCCKH

tCDS tCDH

WRITE Command Input Timing

CSN

VIH

CCLK VIL

VIH

CDTI VIL

VIH

VIL

D3 D2 D1 D0

tCSW

tCSH

WRITE Data Input Timing

tPD

VIL

PDN

Power-down Timing

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 9 -

OPERATION OVERVIEW

n System Clock

The external clocks, which are required to operate the AK4384, are MCLK, LRCK and BICK. The master clock (MCLK)

should be synchronized with LRCK but the phase is not critical. The MCLK is used to operate the digital interpolation

filter and the delta-sigma modulator. There are two methods to set MCLK frequency. In Manual Setting Mode (ACKS =

“0”: Register 00H), the sampling speed is set by DFS0/1(Table 1). The frequency of MCLK at each sampling speed is set

automatically. (Table 2~4).After exiting reset (PDN = “↑”), the AK4384 is in Auto Setting Mode. In Auto Setting Mode

(ACKS = “1”: Default), as MCLK frequency is detected automatically (Table 5), and the internal master clock becomes the

appropriate frequency (Table 6), it is not necessary to set DFS0/1.

In parallel mode, the sampling speed can be set by only ACKS pin. The internal DFS0 andDFS1 bits are fixed to “0”.

Therefore, when ACKS pin is “L”, the AK4384 operates in Normal Speed Mode. The AK4384 operates in Auto Setting

Mode at ACKS = “H”. In parallel mode, the AK4384 does not support 128fs and 192fs of Double Speed Mode.

All external clocks (MCLK,BICK and LRCK) should always be present whenever the AK4384 is in the normal operation

mode (PDN= ”H”). If these clocks are not provided, the AK4384 may draw excess current and may fall into unpredictable

operation. This is because the device utilizes dynamic refreshed logic internally. The AK4384 should be reset by PDN=

“L” after threse clocks are provided. If the external clocks are not present, the AK4384 should be in the power-down mode

(PDN= “L”). After exiting reset at power-up etc., the AK4384 is in the power-down mode until MCLK and LRCK are

input.

DFS1 DFS0 Sampling Rate (fs)

0 0 Normal Speed Mode 8kHz~48kHz Default

0 1 Double Speed Mode 60kHz~96kHz

1 0 Quad Speed Mode 120kHz~192kHz

Table 1. Sampling Speed (Manual Setting Mode)

LRCK MCLK BICK

fs 256fs 384fs 512fs 768fs 1152fs 64fs

32.0kHz 8.1920MHz 12.2880MHz 16.3840MHz 24.5760MHz 36.8640MHz 2.0480MHz

44.1kHz 11.2896MHz 16.9344MHz 22.5792MHz 33.8688MHz N/A 2.8224MHz

48.0kHz 12.2880MHz 18.4320MHz 24.5760MHz 36.8640MHz N/A 3.0720MHz

Table 2. System Clock Example (Normal Speed Mode @Manual Setting Mode)

LRCK MCLK BICK

fs 128fs 192fs 256fs 384fs 64fs

88.2kHz 11.2896MHz 16.9344MHz 22.5792MHz 33.8688MHz 5.6448MHz

96.0kHz 12.2880MHz 18.4320MHz 24.5760MHz 36.8640MHz 6.1440MHz

Table 3. System Clock Example (Double Speed Mode @Manual Setting Mode)

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 10 -

LRCK MCLK BICK

fs 128fs 192fs 64fs

176.4kHz 22.5792MHz 33.8688MHz 11.2896MHz

192.0kHz 24.5760MHz 36.8640MHz 12.2880MHz

Table 4. System Clock Example (Quad Speed Mode @Manual Setting Mode)

MCLK Sampling Speed

512fs 768fs Normal

256fs 384fs Double

128fs 192fs Quad

Table 5. Sampling Speed (Auto Setting Mode: Default)

LRCK MCLK (MHz)

fs 128fs 192fs 256fs 384fs 512fs 768fs 1152fs Sampling

Speed

32.0kHz - - - - 16.3840 24.5760 36.8640

44.1kHz - - - - 22.5792 33.8688 -

48.0kHz - - - - 24.5760 36.8640 - Normal

88.2kHz - - 22.5792 33.8688 - - -

96.0kHz - - 24.5760 36.8640 - - - Double

176.4kHz 22.5792 33.8688 - - - - -

192.0kHz 24.5760 36.8640 - - - - - Quad

Table 6. System Clock Example (Auto Setting Mode)

n Audio Serial Interface Format

Data is shifted in via the SDTI pin using BICK and LRCK inputs. The DIF0-2 as shown in Table 7 can select five serial

data modes. In all modes the serial data is MSB-first, 2’s compliment format and is latched on the rising edge of BICK.

Mode 2 can be used for 16/20 MSB justified formats by zeroing the unused LSBs.

Mode DIF2 DIF1 DIF0 SDTI Format BICK Figure

0 0 0 0 16bit LSB Justified ≥32fs Figure 1

1 0 0 1 20bit LSB Justified ≥40fs Figure 2

2 0 1 0 24bit MSB Justified ≥48fs Figure 3 Default

3 0 1 1 24bit I2S Compatible ≥48fs Figure 4

4 1 0 0 24bit LSB Justified ≥48fs Figure 2

Table 7. Audio Data Formats (Serial mode)

Mode DIF0 SDTI Format BICK Figure

2 0 24bit MSB Justified ≥48fs Figure 3

3 1 24bit I2S Compatible ≥48fs Figure 4

Table 8. Audio Data Formats (Parallel mode)

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 11 -

SDTI

BICK

LRCK

SDTI

15 14 6 5 4

BICK

0 1 10 11 12 13 14 15 0 1 10 11 12 13 14 15 0 1

3 2 1 0 15 14

(32fs)

(64fs)

014

115 16 17 31 0 1 14 15 16 17 31 0 1

15 14 015 14 0

Mode 0

Don’t care Don’t care

15:MSB, 0:LSB

Mode 0

15 14 6 5 4 3 2 1 0

Lch Data Rch Data

Figure 1. Mode 0 Timing

SDTI

LRCK

BICK

(64fs)

0 91 10 11 12 31 0 1 9 10 11 12 31 0 1

19 019 0

Mode 1

Don’t care Don’t care

19:MSB, 0:LSB

SDTI

Mode 4

23:MSB, 0:LSB

20 19 020 19 0

Don’t care Don’t care

22 21 22 21

Lch Data Rch Data

8

23 23

8

Figure 2. Mode 1,4 Timing

LRCK

BICK

(64fs)

SDTI

0221 2 24 31 0 1 31 0 1

23:MSB, 0:LSB

22 1 0 Don’t care23

Lch Data Rch Data

23 30 2222423 30

22 10Don’t care

23 2223

Figure 3. Mode 2 Timing

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 12 -

LRCK

BICK

(64fs)

SDTI

0 31 2 24 31 0 1 31 0 1

23:MSB, 0:LSB

22 10Don’t care

23

Lch Data Rch Data

23 25 32 2423 25

22 10Don’t care23 23

Figure 4. Mode 3 Timing

n De-emphasis Filter

A digital de-emphasis filter is available for 32, 44.1 or 48kHz sampling rates (tc = 50/15µs) and is enabled or disabled with

DEM0 and DEM1. In case of double speed and quad speed mode, the digital de-emphasis filter is always off.

DEM1 DEM0 Mode

0 0 44.1kHz

0 1 OFF Default

1 0 48kHz

1 1 32kHz

Table 9. De-emphasis Filter Control (Normal Speed Mode)

n

Output Volume

The AK4384 includes channel independent digital output volumes (ATT) with 256 levels at linear step including MUTE.

These volumes are in front of the DAC and can attenuate the input data from 0dB to –48dB and mute. When changing

levels, transitions are executed via soft changes; thus no switching noise occurs during these transitions. The transition time

of 1 level and all 256 levels is shown in Table 10.

Transition Time Sampling Speed 1 Level 255 to 0

Normal Speed Mode 4LRCK 1020LRCK

Double Speed Mode 8LRCK 2040LRCK

Quad Speed Mode 16LRCK 4080LRCK

Table 10. ATT Transition Time

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 13 -

n Zero Detection

The AK4384 has channel-independent zeros detect function. When the input data at each channel is continuously zeros for

8192 LRCK cycles, DZF pin of each channel goes to “H”. DZF pin of each channel immediately goes to “L” if input data

of each channel is not zero after going DZF “H”. If RSTN bit is “0”, DZF pins of both channels go to “H”. DZF pin of both

channels go to “L” at 2~3/fs after RSTN bit returns to “1”. If DZFM bit is set to “1”, DZF pins of both channels go to “H”

only when the input data at both channels are continuously zeros for 8192 LRCK cycles. Zero detect function can be

disabled by DZFE bit. In this case, DZF pins of both channels are always “L”. DZFB bit can invert the polarity of DZF pin.

n Soft Mute Operation

Soft mute operation is performed at digital domain. When the SMUTE bit goes to “1”, the output signal is attenuated by -∞

during ATT_DATA×ATT transition time (Table 10) from the current ATT level. When the SMUTE bit is returned to “0”,

the mute is cancelled and the output attenuation gradually changes to the ATT level during ATT_DATA×ATT transition

time. If the soft mute is cancelled before attenuating to -∞ after starting the operation, the attenuation is discontinued and

returned to ATT level by the same cycle. The soft mute is effective for changing the signal source without stopping the

signal transmission.

SMUTE bit

Attenuation

DZF pin

ATT Level

-∞

AOUT

8192/fs

GD GD

(1)

(2)

(3)

(4)

(1)

Notes:

(1) ATT_DATA×ATT transition time (Table 10). For example, in Normal Speed Mode, this time is 1020LRCK cycles

(1020/fs) at ATT_DATA=255.

(2) The analog output corresponding to the digital input has a group delay, GD.

(3) If the soft mute is cancelled before attenuating to -∞ after starting the operation, the attenuation is discontinued and

returned to ATT level by the same cycle.

(4) When the input data at each channel is continuously zeros for 8192 LRCK cycles, DZF pin of each channel goes to

“H”. DZF pin immediately goes to “L” if input data are not zero after going DZF “H”.

Figure 5. Soft Mute and Zero Detection

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 14 -

n System Reset

The AK4384 should be reset once by bringing PDN= “L” upon power-up. The AK4384 is powered up and the internal

timing starts clocking by LRCK “↑” after exiting reset and power down state by MCLK. The AK4384 is in the power-down

mode until MCLK and LRCK are input.

n Power-down

The AK4384 is placed in the power-down mode by bringing PDN pin “L” and the anlog outputs are floating (Hi-Z). Figure

6 shows an example of the system timing at the power-down and power-up.

Normal Operation

Internal

State

PDN

Power-down Normal Operation

GD GD

“0” data

D/A Out

(Analog)

D/A In

(Digital)

Clock In

MCLK, LRCK, BICK

(1) (3)

(6)

DZFL/DZFR

External

MUTE

(5)

(3) (1)

Mute ON

(2)

(4)

Don’t care

Notes:

(1) The analog output corresponding to digital input has the group delay (GD).

(2) Analog outputs are floating (Hi -Z) at the power-down mode.

(3) Click noise occurs at the edge of PDN signal. This noise is output even if “0” data is input.

(4) The external clocks (MCLK, BICK and LRCK) can be stopped in the power-down mode (PDN = “L”).

(5) Please mute the analog output externally if the click noise (3) influences system application.

The timing example is shown in this figure.

(6) DZF pins are “L” in the power-down mode (PDN = “L”).

Figure 6. Power-down/up Sequence Example

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 15 -

n

Reset Function

When RSTN =0, DAC is powered down but the internal register values are not initialized. The analog outputs go to VCOM

voltage and DZFL/DZFR pins go to “H”. Figure 7 shows the example of reset by RSTN bit.

Internal

State

RSTN bit

Digital Block Power-down Normal Operation

GD GD

“0” data

D/A Out

(Analog)

D/A In

(Digital)

Clock In

MCLK,LRCK,BICK

(1) (3)

DZF

(3) (1)

(2)

Normal Operation

2/fs(5)

Internal

RSTN bit

2~3/fs (6)3~4/fs (6)

Don’t care

(4)

Notes:

(1) The analog output corresponding to digital input has the group delay (GD).

(2) Analog outputs go to VCOM voltage (VDD/2).

(3) Click noise occurs at the edges(“↑ ↓”) of the internal timing of RSTN bit. This noise is output even if “0” data is

input.

(4) The external clocks (MCLK, BICK and LRCK) can be stopped in the reset mode (RSTN = “L”).

(5) DZF pins go to “H” when the RSTN bit becomes “0”, and go to “L” at 2/fs after RSTN bit becomes “1”.

(6) There is a delay, 3~4/fs from RSTN bit “0” to the internal RSTN bit “0”, and 2~3/fs from RSTN bit “1” to the

internal RSTN “1”.

Figure 7. Reset Sequence Example

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 16 -

n

Mode Control Interface

Some function of the AK4384 can be controlled by pins (parallel control mode) shown in Table 11. The serial control

interface is enabled by the P/S pin = “L”. Internal registers may be written by 3-wire µP interface pins, CSN, CCLK and

CDTI. The data on this interface consists of Chip Address (2bits, C1/0; fixed to “01”), Read/Write (1bit; fixed to “1”,

Write only), Register Address (MSB first, 5bits) and Control Data (MSB first, 8bits). AK4384 latches the data on the rising

edge of CCLK, so data should clocked in on the falling edge. The writing of data becomes valid by CSN “↑”. The clock

speed of CCLK is 5MHz (max).

Function Parallel mode Serial mode

Double sampling mode at 128/192fs X O

De-emphasis X O

SMUTE O O

Zero Detection O O

16/20/24bit LSB justified format X O

Table 11. . Function list (O: available, X: not available)

PDN = “L” resets the registers to their default values. When the state of P/S pin is changed, the AK4384 should be reset by

PDN= “L”. The internal timing circuit is reset by RSTN bit, but the registers are not initialized.

CDTI

CCLK

CSN

C1

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

D4

D5

D6

D7

A1

A2

A3

A4

R/W

C0

A0

D0

D1

D2

D3

C1-C0: Chip Address (Fixed to “01”)

R/W: READ/WRITE (Fixed to “1”, Write only)

A4-A0: Register Address

D7-D0: Control Data

Figure 8. Control I/F Timing

*The AK4384 does not support the read command and chip address. C1/0 and R/W are fixed to “011”

*When the AK4384 is in the power down mode (PDN = “L”) or the MCLK is not provided, writing into the control register

is inhibited.

n Register Map

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

00H Control 1 ACKS 0 0 DIF2 DIF1 DIF0 PW RSTN

01H Control 2 DZFE DZFM SLOW DFS1 DFS0 DEM1 DEM0 SMUTE

02H Control 3 0 0 0 INVL INVR DZFB 0 0

03H Lch ATT ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0

04H Rch ATT ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0

Notes:

For addresses from 05H to 1FH, data must not be written.

When PDN pin goes “L”, the registers are initialized to their default values.

When RSTN bit goes “0”, the only internal timing is reset and the registers are not initialized to their default values.

All data can be written to the register even if PW or RSTN bit is “0”.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 17 -

n

Register Definitions

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

00H Control 1 ACKS 0 0 DIF2 DIF1 DIF0 PW RSTN

default 1 0 0 0 1 0 1 1

RSTN: Internal timing reset control

0: Reset. All registers are not initialized.

1: Normal Operation

When MCLK frequency or DFS changes, the AK4384 should be reset by PDN pin or RSTN bit.

PW: Power down control

0: Power down. All registers are not initialized.

1: Normal Operation

DIF2-0: Audio data interface formats (see Table 7)

Initial: “010”, Mode 2

ACKS: Master Clock Frequency Auto Setting Mode Enable

0: Disable, Manual Setting Mode

1: Enable, Auto Setting Mode

Master clock frequency is detected automatically at ACKS bit “1”. In this case, the setting of DFS1-0

are ignored. When this bit is “0”, DFS1-0 set the sampling speed mode.

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

01H Control 2 DZFE DZFM SLOW DFS1 DFS0 DEM1 DEM0 SMUTE

default 0 0 0 0 0 0 1 0

SMUTE: Soft Mute Enable

0: Normal operation

1: DAC outputs soft-muted

DEM1-0: De-emphasis Response (see Table 9)

Initial: “01”, OFF

DFS1-0: Sampling speed control

00: Normal speed

01: Double speed

10: Quad speed

When changing betw een Normal/Double Speed Mode and Quad Speed Mode, some click noise occurs.

SLOW: Slow Roll-off Filter Enable

0: Sharp Roll-off Filter

1: Slow Roll-off Filter

DZFE: Data Zero Detect Enable

0: Disable

1: Enable

Zero detect function can be disabled by DZFE bit “0”. In this case, the DZF pins of both channels are

always “L”.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 18 -

DZFM: Data Zero Detect Mode

0: Channel Separated Mode

1: Channel ANDed Mode

If the DZFM bit is set to “1”, the DZF pins of both channels go to “H” only when the input data at both

channels are continuously zeros for 8192 LRCK cycles.

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

02H Control 3 0 0 0 INVL INVR DZFB 0 0

default 0 0 0 0 0 0 0 0

DZFB: Inverting Enable of DZF

0: DZF goes “H” at Zero Detection

1: DZF goes “L” at Zero Detection

INVR: Inverting Lch Output Polarity

0: Normal Output

1: Inverted Output

INVL: Inverting Rch Output Polarity

0: Normal Output

1: Inverted Output

Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0

03H Lch ATT ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0

04H Rch ATT ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0

default 1 1 1 1 1 1 1 1

ATT = 20 log10 (ATT_DATA / 255) [dB]

00H: Mute

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 19 -

SYSTEM DESIGN

Figure 9 and 10 show the system connection diagram. An evaluation board (AKD4384) is available in order to allow an

easy study on the layout of a surrounding circuit.

MCLK 1

BICK 2

SDTI

3

LRCK

4

PDN

5

SMUTE

6

ACKS

7

DIF0

8

DZFL

16

DZFR

15

VDD

14

VSS

13

VCOM

12

AOUTL

11

AOUTR

10

P/S

9

Master Clock

Mode

Setting

AK4384

fs

24bit Audio Data

Reset & Power down

64fs

10u

0.1u

+

Rch Out

Lch Out

MUTE

Analog Ground Digital Ground

Lch

MUTE

Rch

MUTE

Analog

Supply 5V

+

10u

Figure 9. Typical Connection Diagram (Parallel Mode)

MCLK 1

BICK 2

SDTI

3

LRCK

4

PDN

5

CSN

6

CCLK

7

CDTI

8

DZFL

16

DZFR

15

VDD

14

VSS

13

VCOM

12

AOUTL

11

AOUTR

10

P/S

9

Master Clock

Micro-

controller

AK4384

fs

24bit Audio Data

Reset & Power down

64fs

10u

0.1u

+

Rch Out

Lch Out

MUTE

Analog Ground Digital Ground

Lch

MUTE

Rch

MUTE

Analog

Supply 5V

+

10u

Figure 10. Typical Connection Diagram (Serial Mode)

Notes:

- LRCK = fs, BICK = 64fs.

- When AOUT drives some capacitive load, some resistor should be added in series between AOUT and capacitive

load.

- All input pins except pull-up pin should not be left floating.

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 20 -

1. Grounding and Power Supply Decoupling

VDD and VSS are supplied from analog supply and should be separated from system digital supply. Decoupling capacitor,

especially 0.1µF ceramic capacitor for high frequency should be placed as near to VDD as possible. The differential

Voltage between VDD and VSS pins set the analog output range.

2. Analog Outputs

The analog outputs are single-ended and centered around the VCOM voltage. The output signal range is typically 3.40Vpp

(typ@VDD=5V). The phase of the analog outputs can be inverted channel independently by INVL/INVR bits. The

internal switched-capacitor filter and continuous-time filter attenuate the noise generated by the delta-sigma modulator

beyond the audio passband. The output voltage is a positive full scale for 7FFFFFH (@24bit) and a negative full scale for

800000H (@24bit). The ideal output is VCOM voltage for 000000H (@24bit).

DC offsets on analog outputs are eliminated by AC coupling since analog outputs have DC offsets of VCOM + a few mV.

Figure 11 shows an example of the external LPF with 2Vrms output.

820p

3.3k

1.5k 1.8k

820p

+Vop

2.2k

-Vop

AOUT 22u

fc=111.8kHz, Q=0.714, g=-0.04dB at 40kHz

Analog

Out

10k

Figure 11. External 2nd order LPF Circuit Example (using op-amp with dual power supplies)

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 21 -

PACKAGE

0-10°

Detail A

Seating Plane

0.10

0.17±0.05

0.22±0.1

0.65

*5.0±0.1

1.05±0.05

A

1

8

9

16

16pin TSSOP (Unit: mm)

*4.4±0.1

6.4±0.2

0.5±0.2

0.1±0.1

NOTE: Dimension "*" does not include mold flash.

0.13

M

n

Package & Lead frame material

Package molding compound: Epoxy

Lead frame material: Cu

Lead frame surface treatment: Solder(Pb free) plate

ASAHI KASEI [AK4384]

MS0176-E-00 2002/09

- 22 -

MARKING

AKM

4384VT

XXYYY

1) Pin #1 indication

2) Date Code : XXYYY (5 digits)

XX: Lot#

YYY: Date Code

3) Marketing Code : 4384VT

4) Asahi Kasei Logo

IMPORTANT NOTICE

• These products and their specifications are subject to change without notice. Before considering any

use or application, consult the Asahi Kasei Microsystems Co., Ltd. (AKM) sales office or authorized

distributor concerning their current status.

• AKM assumes no liability for infringement of any patent, intellectual property, or other right in the

application or use of any information contained herein.

• Any export of these products, or devices or systems containing them, may require an export license

or other official approval under the law and regulations of the country of export pertaining to customs

and tariffs, currency exchange, or strategic materials.

• AKM products are neither intended nor authorized for use as critical components in any safety, life

support, or other hazard related device or system, and AKM assumes no responsibility relating to any

such use, except with the express written consent of the Representative Director of AKM. As used

here:

(a) A hazard related device or system is one designed or intended for life support or maintenance of

safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its

failure to function or perform may reasonably be expected to result in loss of life or in significant

injury or damage to person or property.

(b) A critical component is one whose failure to function or perform may reasonably be expected to

result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or

system containing it, and which must therefore meet very high standards of performance and

reliability.

• It is the responsibility of the buyer or distributor of an AKM product who distributes, disposes of, or

otherwise places the product with a third party to notify that party in advance of the above content and

conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and

hold AKM harmless from any and all claims arising from the use of said product in the absence of such

notification.