8-/10-/12-/14-Bit High Bandwidth Multiplying DACs with Serial Interface AD5450/AD5451/AD5452/AD5453 FEATURES FUNCTIONAL BLOCK DIAGRAM 12 MHz multiplying bandwidth INL of 0.25 LSB @ 8-bit 8-lead TSOT and MSOP packages 2.5 V to 5.5 V supply operation Pin-compatible 8-/10-/12-/14-bit current output DACs 10 V reference input 50 MHz serial interface 2.7 MSPS update rate Extended temperature range: -40C to +125C 4-quadrant multiplication Power-on reset with brownout detect <0.4 A typical current consumption Guaranteed monotonic VDD AD5450/ AD5451/ AD5452/ AD5453 VREF R 8-/10-/12-/14-BIT REF R-2R DAC RFB IOUT1 DAC REGISTER POWER-ON RESET SYNC SCLK SDIN APPLICATIONS CONTROL LOGIC AND INPUT SHIFT REGISTER 04587-001 INPUT LATCH GND Portable battery-powered applications Waveform generators Analog processing Instrumentation applications Programmable amplifiers and attenuators Digitally controlled calibration Programmable filters and oscillators Composite video Ultrasound Gain, offset, and voltage trimming Figure 1. GENERAL DESCRIPTION The AD5450/AD5451/AD5452/AD5453 1 are CMOS 8-/10-/ 12-/14-bit current output digital-to-analog converters, respectively. These devices operate from a 2.5 V to 5.5 V power supply, making them suited to several applications, including battery-powered applications. As a result of manufacture on a CMOS submicron process, these DACs offer excellent 4-quadrant multiplication characteristics of up to 12 MHz. These DACs utilize a double-buffered, 3-wire serial interface that is compatible with SPI(R), QSPITM, MICROWIRETM, and most DSP interface standards. Upon power-up, the internal shift register and latches are filled with 0s, and the DAC output is at zero scale. The applied external reference input voltage (VREF) determines the full-scale output current. These parts can handle 10 V inputs on the reference, despite operating from a single-supply power supply of 2.5 V to 5.5 V. An integrated feedback resistor (RFB) provides temperature tracking and full-scale voltage output when combined with an external current-to-voltage precision amplifier. The AD5450/AD5451/AD5452/AD5453 DACs are available in small 8-lead TSOT, and the AD5452/AD5453 are also available in MSOP packages. 1 U.S. Patent Number 5,689,257. Rev. C Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2005-2010 Analog Devices, Inc. All rights reserved. AD5450/AD5451/AD5452/AD5453 TABLE OF CONTENTS Features .............................................................................................. 1 Circuit Operation ....................................................................... 16 Applications ....................................................................................... 1 Single-Supply Applications ....................................................... 18 Functional Block Diagram .............................................................. 1 Adding Gain ................................................................................ 18 General Description ......................................................................... 1 Divider or Programmable Gain Element ................................ 19 Revision History ............................................................................... 2 Reference Selection .................................................................... 19 Specifications..................................................................................... 3 Amplifier Selection .................................................................... 19 Timing Characteristics ................................................................ 5 Serial Interface ............................................................................ 21 Absolute Maximum Ratings............................................................ 6 Microprocessor Interfacing ....................................................... 21 ESD Caution .................................................................................. 6 PCB Layout and Power Supply Decoupling ........................... 23 Pin Configurations and Function Descriptions ........................... 7 Evaluation Board for the DAC...................................................... 24 Typical Performance Characteristics ............................................. 8 Power Supplies for the Evaluation Board ................................ 24 Terminology .................................................................................... 15 Outline Dimensions ....................................................................... 27 General Description ....................................................................... 16 Ordering Guide .......................................................................... 28 DAC Section ................................................................................ 16 REVISION HISTORY 1/10--Rev. B to Rev. C Changes to DAC Control Bits C1, C0 .......................................... 21 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 28 3/06--Rev. A to Rev. B Updated Format .................................................................. Universal Changes to Features.......................................................................... 1 Changes to General Description .................................................... 1 Changes to Specifications ................................................................ 4 Changes to Figure 27 and Figure 28 ............................................. 11 Change to Table 9 ........................................................................... 20 Changes to Table 12 ........................................................................ 26 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 28 7/05--Rev. 0 to Rev. A Added AD5453 ................................................................... Universal Changes to Specifications ................................................................ 4 Change to Figure 21 ....................................................................... 10 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 28 1/05--Revision 0: Initial Version Rev. C | Page 2 of 28 AD5450/AD5451/AD5452/AD5453 SPECIFICATIONS VDD = 2.5 V to 5.5 V, VREF = 10 V. Temperature range for Y version: -40C to +125C. All specifications TMIN to TMAX, unless otherwise noted. DC performance measured with OP177 and ac performance measured with AD8038, unless otherwise noted. Table 1. Parameter STATIC PERFORMANCE AD5450 Resolution Relative Accuracy Differential Nonlinearity Total Unadjusted Error Gain Error AD5451 Resolution Relative Accuracy Differential Nonlinearity Total Unadjusted Error Gain Error AD5452 Resolution Relative Accuracy Differential Nonlinearity Total Unadjusted Error Gain Error AD5453 Resolution Relative Accuracy Differential Nonlinearity Total Unadjusted Error Gain Error Gain Error Temperature Coefficient 1 Output Leakage Current REFERENCE INPUT1 Reference Input Range VREF Input Resistance RFB Feedback Resistance Input Capacitance Zero-Scale Code Full-Scale Code DIGITAL INPUTS/OUTPUTS1 Input High Voltage, VIH Min Output Low Voltage, VOL Input Leakage Current, IIL Input Capacitance Max Unit Conditions 8 0.25 0.5 0.5 0.25 Bits LSB LSB LSB LSB Guaranteed monotonic 10 0.25 0.5 0.5 0.25 Bits LSB LSB LSB LSB Guaranteed monotonic 12 0.5 1 1 0.5 Bits LSB LSB LSB LSB Guaranteed monotonic 14 2 -1/+2 4 2.5 1 10 Bits LSB LSB LSB LSB ppm FSR/C nA nA 10 9 9 11 11 V k k 18 18 22 22 pF pF 2 7 7 2.0 1.7 Input Low Voltage, VIL Output High Voltage, VOH Typ 0.8 0.7 VDD - 1 VDD - 0.5 0.4 0.4 1 10 10 V V V V V V V V nA nA pF Rev. C | Page 3 of 28 Guaranteed monotonic Data = 0x0000, TA = 25C, IOUT1 Data = 0x0000, TA = -40C to +125C, IOUT1 Input resistance, TC = -50 ppm/C Input resistance, TC = -50 ppm/C VDD = 3.6 V to 5 V VDD = 2.5 V to 3.6 V VDD = 2.7 V to 5.5 V VDD = 2.5 V to 2.7 V VDD = 4.5 V to 5 V, ISOURCE = 200 A VDD = 2.5 V to 3.6 V, ISOURCE = 200 A VDD = 4.5 V to 5 V, ISINK = 200 A VDD = 2.5 V to 3.6 V, ISINK = 200 A TA = 25C TA = -40C to +125C AD5450/AD5451/AD5452/AD5453 Parameter DYNAMIC PERFORMANCE1 Reference-Multiplying BW Multiplying Feedthrough Error Min Typ Max Unit Conditions 12 MHz 72 64 44 dB dB dB VREF = 3.5 V, DAC loaded with all 1s VREF = 3.5 V, DAC loaded with all 0s 100 kHz 1 MHz 10 MHz VREF = 10 V, RLOAD = 100 ; DAC latch alternately loaded with 0s and 1s Output Voltage Settling Time Measured to 1 mV of FS Measured to 4 mV of FS Measured to 16 mV of FS Digital Delay 10% to 90% Settling Time Digital-to-Analog Glitch Impulse Output Capacitance IOUT1 100 24 16 20 10 2 IOUT2 Digital Feedthrough Analog THD Digital THD 50 kHz fOUT 20 kHz fOUT Output Noise Spectral Density SFDR Performance (Wide Band) 50 kHz fOUT 20 kHz fOUT SFDR Performance (Narrow Band) 50 kHz fOUT 20 kHz fOUT Intermodulation Distortion POWER REQUIREMENTS Power Supply Range IDD 110 40 33 40 30 13 28 18 5 0.5 pF pF pF pF nV-s 83 dB 71 77 25 dB dB nV/Hz 78 74 dB dB Interface delay time Rise and fall times, VREF = 10 V, RLOAD = 100 1 LSB change around major carry, VREF = 0 V DAC latches loaded with all 0s DAC latches loaded with all 1s DAC latches loaded with all 0s DAC latches loaded with all 1s Feedthrough to DAC output with CS high and alternate loading of all 0s and all 1s VREF = 3.5 V p-p, all 1s loaded, f = 1 kHz Clock = 1 MHz, VREF = 3.5 V @ 1 kHz Clock = 1 MHz, VREF = 3.5 V Clock = 1 MHz, VREF = 3.5 V 87 85 79 2.5 5.5 10 0.6 0.001 0.4 Power Supply Sensitivity1 1 ns ns ns ns ns nV-s dB dB dB f1 = 20 kHz, f2 = 25 kHz, clock = 1 MHz, VREF = 3.5 V V A A %/% TA = -40C to +125C, logic inputs = 0 V or VDD TA = 25C, logic inputs = 0 V or VDD VDD = 5% Guaranteed by design and characterization, not subject to production test. Rev. C | Page 4 of 28 AD5450/AD5451/AD5452/AD5453 TIMING CHARACTERISTICS All input signals are specified with tR = tF = 1 ns (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2. VDD = 2.5 V to 5.5 V, VREF = 10 V, temperature range for Y version: -40C to +125C. All specifications TMIN to TMAX, unless otherwise noted. Table 2. Parameter 1 fSCLK t1 t2 t3 t4 t5 t6 t7 t8 Update Rate Unit MHz max ns min ns min ns min ns min ns min ns min ns min ns min MSPS Conditions/Comments Maximum clock frequency SCLK cycle time SCLK high time SCLK low time SYNC falling edge to SCLK active edge setup time Data setup time Data hold time SYNC rising edge to SCLK active edge Minimum SYNC high time Consists of cycle time, SYNC high time, data setup, and output voltage settling time Guaranteed by design and characterization, not subject to production test. t1 SCLK t8 t2 t3 t7 t4 SYNC t6 t5 DIN DB15 DB0 Figure 2. Timing Diagram Rev. C | Page 5 of 28 04587-002 1 VDD = 2.5 V to 5.5 V 50 20 8 8 8 5 4.5 5 30 2.7 AD5450/AD5451/AD5452/AD5453 ABSOLUTE MAXIMUM RATINGS Transient currents of up to 100 mA do not cause SCR latch-up. TA = 25C, unless otherwise noted. Table 3. Parameter VDD to GND VREF, RFB to GND IOUT1 to GND Input Current to Any Pin Except Supplies Logic Inputs and Output 1 Operating Temperature Range, Extended (Y Version) Storage Temperature Range Junction Temperature JA Thermal Impedance 8-Lead MSOP 8-Lead TSOT Lead Temperature, Soldering (10 sec) IR Reflow, Peak Temperature (<20 sec) 1 Rating -0.3 V to +7 V -12 V to +12 V -0.3 V to +7 V 10 mA -0.3 V to VDD + 0.3 V -40C to +125C -65C to +150C 150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION 206C/W 211C/W 300C 235C Overvoltages at SCLK, SYNC, and SDIN are clamped by internal diodes. Rev. C | Page 6 of 28 AD5450/AD5451/AD5452/AD5453 VDD 3 SYNC 4 AD5450/ AD5451/ AD5452/ AD5453 8 IOUT1 IOUT1 1 7 GND GND 2 6 SCLK SCLK 3 5 SDIN 04587-003 RFB 1 VREF 2 SDIN 4 Figure 3. TSOT Pin Configuration AD5452/ AD5453 8 RFB 7 VREF 6 VDD 5 SYNC 04587-004 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 4. MSOP Pin Configuration Table 4. Pin Function Descriptions Pin No. TSOT MSOP 1 8 2 7 3 6 4 5 Mnemonic RFB VREF VDD SYNC 5 4 SDIN 6 3 SCLK 7 8 2 1 GND IOUT1 Description DAC Feedback Resistor. Establish voltage output for the DAC by connecting to external amplifier output. DAC Reference Voltage Input. Positive Power Supply Input. These parts can operate from a supply of 2.5 V to 5.5 V. Active Low Control Input. This is the frame synchronization signal for the input data. Data is loaded to the shift register upon the active edge of the following clocks. Serial Data Input. Data is clocked into the 16-bit input register upon the active edge of the serial clock input. By default, in power-up mode data is clocked into the shift register upon the falling edge of SCLK. The control bits allow the user to change the active edge to a rising edge. Serial Clock Input. By default, data is clocked into the input shift register upon the falling edge of the serial clock input. Alternatively, by means of the serial control bits, the device can be configured such that data is clocked into the shift register upon the rising edge of SCLK. Ground Pin. DAC Current Output. Rev. C | Page 7 of 28 AD5450/AD5451/AD5452/AD5453 TYPICAL PERFORMANCE CHARACTERISTICS 1.2 0.10 0.8 0.05 0.4 INL (LSB) 0.15 0 -0.05 0 -0.4 -0.10 -0.8 -0.15 -1.2 -0.20 -0.25 0 32 TA = 25C VREF = 10V VDD = 5V 1.6 04587-020 INL (LSB) 2.0 TA = 25C VREF = 10V VDD = 5V 0.20 64 96 128 160 192 224 04587-023 0.25 -1.6 -2.0 256 0 2048 4096 6144 CODE Figure 5. INL vs. Code (8-Bit DAC) 0.5 0.3 0.10 0.2 0.05 0.1 DNL (LSB) 0.15 0 -0.05 0 -0.1 -0.10 -0.2 -0.15 -0.3 -0.20 -0.25 0 128 TA = 25C VREF = 10V VDD = 5V 0.4 04587-021 INL (LSB) Figure 8. INL vs. Code (14-Bit DAC) TA = 25C VREF = 10V VDD = 5V 0.20 256 384 512 640 768 896 -0.4 -0.5 1024 0 32 64 96 CODE 0.2 0.2 0.1 0.1 0 -0.1 -0.3 -0.3 -0.4 1536 2048 896 1024 0 -0.2 1024 256 -0.1 -0.2 512 224 2560 3072 2584 04587-025 DNL (LSB) 0.3 0 192 TA = 25C VREF = 10V VDD = 5V 0.4 04587-022 INL (LSB) 0.5 0.3 -0.5 160 Figure 9. DNL vs. Code (8-Bit DAC) TA = 25C VREF = 10V VDD = 5V 0.4 128 CODE Figure 6. INL vs. Code (10-Bit DAC) 0.5 10240 12288 14336 16384 04587-024 0.25 8192 CODE -0.4 -0.5 4096 CODE 0 128 256 384 512 640 768 CODE Figure 7. INL vs. Code (12-Bit DAC) Figure 10. DNL vs. Code (10-Bit DAC) Rev. C | Page 8 of 28 AD5450/AD5451/AD5452/AD5453 1.0 2.0 TA = 25C VREF = 10V VDD = 5V 0.8 TA = 25C VDD = 5V AD5452 1.5 0.6 1.0 MAX DNL 0.5 0.2 DNL (LSB) DNL (LSB) 0.4 0 -0.2 0 MIN DNL -0.5 -0.4 -1.0 -0.6 0 512 1024 1536 2048 2560 3072 2584 -2.0 4096 04587-071 -1.0 -1.5 04587-026 -0.8 2 3 4 CODE Figure 11. DNL vs. Code (12-Bit DAC) 0.8 0.2 0.4 0.1 TUE (LSB) 0.3 0 -0.4 -1.2 -0.3 -1.6 4096 6144 8192 -0.5 10240 12288 14336 16384 0 32 64 96 128 160 192 1024 CODE Figure 12. DNL vs. Code (14-Bit DAC) Figure 15. TUE vs. Code (8-Bit DAC) 1.00 0.25 TA = 25C VDD = 5V AD5452 TA = 25C VREF = 10V VDD = 5V AD5451 0.20 0.15 0.50 896 -0.4 CODE 0.75 256 -0.1 -0.2 2048 224 0 -0.8 0 TA = 25C VREF = 10V VDD = 5V AD5450 0.4 04587-027 DNL (LSB) 0.5 1.2 -2.0 10 Figure 14. DNL vs. Reference Voltage TA = 25C VREF = 10V VDD = 5V 1.6 9 04587-030 2.0 5 6 7 8 REFERENCE VOLTAGE (V) MAX INL 0.10 TUE (LSB) 0 MIN INL -0.25 0.05 0 -0.05 -0.10 -0.50 -1.00 2 3 4 5 6 7 8 REFERENCE VOLTAGE (V) 9 04587-031 -0.15 -0.75 04587-070 INL (LSB) 0.25 -0.20 -0.25 10 0 128 256 384 512 640 768 CODE Figure 13. INL vs. Reference Voltage Figure 16. TUE vs. Code (10-Bit DAC) Rev. C | Page 9 of 28 AD5450/AD5451/AD5452/AD5453 1.0 0.3 TA = 25C VREF = 10V VDD = 5V 0.8 0.2 0.6 GAIN ERROR (LSB) 0.2 0 -0.2 -0.4 -0.6 VDD = 3V VDD = 5V 0 -0.1 04587-032 -0.2 -0.8 -1.0 0.1 0 512 1024 1536 2048 2560 3072 2584 04587-073 TUE (LSB) 0.4 -0.3 -60 4096 -40 -20 0 60 20 40 TEMPERATURE (C) CODE Figure 17. TUE vs. Code (12-Bit DAC) 2.0 100 120 140 Figure 20. Gain Error (LSB) vs. Temperature 2.0 TA = 25C VREF = 10V VDD = 5V 1.6 80 TA = 25C VDD = 5V AD5452 1.5 1.2 1.0 GAIN ERROR (LSB) 0.4 0 -0.4 -0.8 0 -0.5 -1.0 -1.2 -1.5 04587-033 -1.6 -2.0 0.5 0 2048 4096 6144 8192 -2.0 10240 12288 14336 16384 04587-074 INL (LSB) 0.8 2 3 4 CODE Figure 18. TUE vs. Code (14-Bit DAC) 10 2.0 TA = 25C VDD = 5V AD5452 IOUT1 VDD = 5V 1.6 1.0 IOUT1 LEAKAGE (nA) MAX TUE 0.5 0 MIN TUE -0.5 -1.0 IOUT1 VDD = 3V 1.2 0.8 -2.0 2 3 4 5 8 6 7 REFERENCE VOLTAGE (V) 9 0 -40 10 04587-039 0.4 -1.5 04587-072 TUE (LSB) 9 Figure 21. Gain Error (LSB) vs. Reference Voltage 2.0 1.5 5 8 6 7 REFERENCE VOLTAGE (V) -20 0 20 40 60 80 100 TEMPERATURE (C) Figure 19. TUE vs. Reference Voltage Figure 22. IOUT1 Leakage Current vs. Temperature Rev. C | Page 10 of 28 120 AD5450/AD5451/AD5452/AD5453 1.8 2.5 TA = 25C VIH THRESHOLD VOLTAGE (V) 1.5 1.0 VDD = 5V 0.5 0 1 2 3 4 1.2 1.0 0.8 0.6 0.4 04587-076 0.2 04587-038 VDD = 3V 0 2.5 5 3.0 3.5 INPUT VOLTAGE (V) ALL 1s ALL 0s 0 0.6 5.0 GAIN (dB) VDD = 5V 0.4 0.3 DB12 -20 DB11 DB10 -30 DB9 DB8 -40 DB7 DB6 -50 DB5 0.2 VDD = 3V 04587-037 0.1 0 -40 -20 0 20 40 60 80 100 5.5 -60 DB4 DB3 -70 DB2 -80 10k 120 TA = 25C LOADING ZS TO FS ALL ON DB13 -10 0.5 CURRENT (A) 4.5 10 0.7 VDD = 5V VREF = 3.5V CCOMP = 1.8pF AD8038 AMPLIFIER 100k 1M 10M 100M FREQUENCY (Hz) TEMPERATURE (C) Figure 27. Reference Multiplying Bandwidth vs. Frequency and Code Figure 24. Supply Current vs. Temperature 0.6 TA = 25C AD5452 LOADING 010101010101 5 4.0 VOLTAGE (V) Figure 26. Threshold Voltage vs. Supply Voltage Figure 23. Supply Current vs. Logic Input Voltage 6 VIL 1.4 04587-108 CURRENT (mA) 2.0 0 TA = 25C 1.6 0.4 0 3 GAIN (dB) 4 VDD = 5V 2 -0.2 -0.4 -0.6 0 VDD = 3V 1 10 100 1k 10k 100k 1M -1.0 TA = 25C VDD = 5V VREF = 3.5V CCOMP = 1.8pF AD8038 AMPLIFIER -1.2 10k 10M 100k 04587-109 -0.8 1 04587-075 CURRENT (mA) 0.2 1M 10M 100M FREQUENCY (Hz) FREQUENCY (Hz) Figure 25. Supply Current vs. Update Rate Figure 28. Reference Multiplying Bandwidth--All 1s Loaded Rev. C | Page 11 of 28 AD5450/AD5451/AD5452/AD5453 3 10 TA = 25C VDD = 5V TA = 25C VDD = 3V AD8038 AMPLIFIER 0 -10 0 -20 PSRR (dB) -3 -9 10k VREF VREF VREF VREF VREF FULL SCALE -60 ZERO SCALE -70 = 2V, AD8038 C COMP = 1pF = 2V, AD8038 C COMP = 1.5pF = 15V, AD8038 C COMP = 1pF = 15V, AD8038 C COMP = 1.5pF = 15V, AD8038 C COMP = 1.8pF 100k -40 -50 -80 1M 10M 04587-082 -6 04587-079 -90 -100 100M 1 10 100 1k FREQUENCY (Hz) 0.02 0 -0.06 VDD = 5V 0x800 TO 0x7FF NRG = 0.694nVs 50 75 100 125 150 -85 175 200 225 04587-083 -0.04 -75 -80 VDD = 5V 0x800 TO 0x7FF NRG = 0.694nVs -0.02 -90 100 250 1k 100k Figure 33. THD + Noise vs. Frequency Figure 30. Midscale Transition, VREF = 0 V 100 -1.66 TA = 25C VDD = 3.5V AD8038 AMPLIFIER CCOMP = 1.8pF VDD = 5V 0x7FF TO 0x800 NRG = 2.154nVs -1.68 VDD = 3V 0x7FF TO 0x800 NRG = 1.794nVs MCLK = 1MHz SFDR (dB) -1.70 -1.72 -1.74 -1.76 VDD = 5V 0x800 TO 0x7FF NRG = 0.694nVs VDD = 5V 0x800 TO 0x7FF NRG = 0.694nVs -1.78 50 75 100 125 150 MCLK = 200kHz MCLK = 500kHz 80 60 40 20 04587-081 OUTPUT VOLTAGE (V) 10k FREQUENCY (Hz) TIME (ns) -1.80 10M -70 THD + N (dB) 0.04 1M TA = 25C VDD = 5V VREF = 3.5V -65 VDD = 3V 0x7FF TO 0x800 NRG = 1.794nVs 04587-080 OUTPUT VOLTAGE (V) 0.06 -60 TA = 25C VDD = 0V AD8038 AMPLIFIER CCOMP = 1.8pF VDD = 5V 0x7FF TO 0x800 NRG = 2.154nVs 100k Figure 32. Power Supply Rejection Ratio vs. Frequency Figure 29. Reference Multiplying Bandwidth vs. Frequency and Compensation Capacitor 0.08 10k FREQUENCY (Hz) 175 200 225 250 0 TA = 25C VREF = 3.5V AD8038 AMPLIFIER 0 10 04587-084 GAIN (dB) -30 20 30 40 fOUT (kHz) TIME (ns) Figure 31. Midscale Transition, VREF = 3.5 V Figure 34. Wideband SFDR vs. fOUT Frequency Rev. C | Page 12 of 28 50 AD5450/AD5451/AD5452/AD5453 0 0 TA = 25C VDD = 5V VREF = 3.5V AD8038 AMPLIFIER -20 -40 -60 -60 -80 -100 -100 04587-085 -80 0 100k 200k 300k 400k -120 10k 500k 04587-087 SFDR (dB) SFDR (dB) -40 -120 TA = 25C VDD = 5V VREF = 3.5V AD8038 AMPLIFIER -20 15k Figure 35. Wideband SFDR, fOUT = 20 kHz, Clock = 1 MHz 30k 0 TA = 25C VDD = 5V VREF = 3.5V AD8038 AMPLIFIER -20 TA = 25C VDD = 5V VREF = 3.5V AD8038 AMPLIFIER -20 -40 -40 -60 -60 -80 -100 -100 04587-086 -80 0 100k 200k 300k 400k -120 30k 500k FREQUENCY (Hz) 04587-088 SFDR (dB) SFDR (dB) 25k Figure 37. Narrow-Band SFDR, fOUT = 20 kHz, Clock = 1 MHz 0 -120 20k FREQUENCY (Hz) FREQUENCY (Hz) 40k 50k 60k 70k FREQUENCY (Hz) Figure 36. Wideband SFDR, fOUT = 50 kHz, Clock = 1 MHz Figure 38. Narrow-Band SFDR , fOUT = 50 kHz, Clock = 1 MHz Rev. C | Page 13 of 28 AD5450/AD5451/AD5452/AD5453 80 TA = 25C VREF = 3.5V AD8038 AMPLIFIER -10 OUTPUT NOISE (nV/ Hz) -20 -30 -40 IMD (dB) TA = 25C AD8038 AMPLIFIER 70 -50 -60 -70 60 FULL SCALE LOADED TO DAC 50 40 MIDSCALE LOADED TO DAC 30 20 -80 -100 10k 15k 20k 25k 30k 0 100 35k FREQUENCY (Hz) TA = 25C VREF = 3.5V AD8038 AMPLIFIER -20 IMD (dB) -30 -40 -50 -60 -70 04587-090 -80 -90 -100 100k 200k 300k 10k 100k Figure 41. Output Noise Spectral Density 0 0 1k FREQUENCY (Hz) Figure 39. Narrow-Band IMD, fOUT = 20 kHz, 25 kHz, Clock = 1 MHz -10 ZERO SCALE LOADED TO DAC 10 04587-089 -90 400k 500k FREQUENCY (Hz) Figure 40. Wideband IMD, fOUT = 20 kHz, 25 kHz, Clock = 1 MHz Rev. C | Page 14 of 28 04587-091 0 1M AD5450/AD5451/AD5452/AD5453 TERMINOLOGY Relative Accuracy (Endpoint Nonlinearity) A measure of the maximum deviation from a straight line passing through the endpoints of the DAC transfer function. It is measured after adjusting for zero and full scale and is normally expressed in LSBs or as a percentage of the full-scale reading. Differential Nonlinearity The difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of -1 LSB maximum over the operating temperature range ensures monotonicity. Gain Error (Full-Scale Error) A measure of the output error between an ideal DAC and the actual device output. For these DACs, ideal maximum output is VREF - 1 LSB. Gain error of the DACs is adjustable to zero with external resistance. Output Leakage Current The current that flows into the DAC ladder switches when it is turned off. For the IOUT1 terminal, it can be measured by loading all 0s to the DAC and measuring the IOUT1 current. Output Capacitance Capacitance from IOUT1 to AGND. Output Current Settling Time The amount of time it takes for the output to settle to a specified level for a full-scale input change. For these devices, it is specified with a 100 resistor to ground. The settling time specification includes the digital delay from the SYNC rising edge to the fullscale output change. Digital-to-Analog Glitch Impulse The amount of charge injected from the digital inputs to the analog output when the inputs change state. This is normally specified as the area of the glitch in either pA-s or nV-s, depending on whether the glitch is measured as a current or voltage signal. Digital Feedthrough When the device is not selected, high frequency logic activity on the device's digital inputs may be capacitively coupled through the device and produce noise on the IOUT pins. This noise is coupled from the outputs of the device onto follow-on circuitry. This noise is digital feedthrough. Multiplying Feedthrough Error The error due to capacitive feedthrough from the DAC reference input to the DAC IOUT1 terminal when all 0s are loaded to the DAC. Total Harmonic Distortion (THD) The DAC is driven by an ac reference. The ratio of the rms sum of the harmonics of the DAC output to the fundamental value is the THD. Usually only the lower-order harmonics, such as second to fifth, are included. THD = 20 log V 2 2 + V3 2 + V4 2 + V5 2 V1 Digital Intermodulation Distortion (IMD) Second-order intermodulation measurements are the relative magnitudes of the fa and fb tones generated digitally by the DAC and the second-order products at 2fa - fb and 2fb - fa. Compliance Voltage Range The maximum range of (output) terminal voltage for which the device provides the specified characteristics. Spurious-Free Dynamic Range (SFDR) The usable dynamic range of a DAC before spurious noise interferes or distorts the fundamental signal. SFDR is the measure of difference in amplitude between the fundamental and the largest harmonically or nonharmonically related spur from dc to full Nyquist bandwidth (half the DAC sampling rate or fS/2). Narrow-band SFDR is a measure of SFDR over an arbitrary window size, in this case 50% of the fundamental. Digital SFDR is a measure of the usable dynamic range of the DAC when the signal is a digitally generated sine wave. Rev. C | Page 15 of 28 AD5450/AD5451/AD5452/AD5453 GENERAL DESCRIPTION DAC SECTION The AD5450/AD5451/AD5452/AD5453 are 8-/10-/12-/14-bit current output DACs, respectively, consisting of a segmented (4-bit) inverting R-2R ladder configuration. A simplified diagram for the 12-bit AD5452 is shown in Figure 42. VREF R R Note that the output voltage polarity is opposite to the VREF polarity for dc reference voltages. VDD VDD R VREF 2R 2R 2R 2R S1 S2 S3 S12 2R R R1 VREF R2 AD5450/ AD5451/ AD5452/ AD5453 C1 RFB IOUT1 A1 GND VOUT = 0 TO -VREF SYNC SCLK SDIN RFB AGND IOUT1 NOTES 1. R1 AND R2 USED ONLY IF GAIN ADJUSTMENT IS REQUIRED. 2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER. Figure 42. AD5452 Simplified Ladder 04587-009 AGND 04587-060 CONTROLLER DAC DATA LATCHES AND DRIVERS Figure 43. Unipolar Mode Operation The feedback resistor, RFB, has a value of R. The value of R is typically 9 k (with a minimum value of 7 k and a maximum value of 11 k). If IOUT1 is kept at the same potential as GND, a constant current flows in each ladder leg, regardless of digital input code. Therefore, the input resistance presented at VREF is always constant and nominally of value R. The DAC output (IOUT1) is code-dependent, producing various resistances and capacitances. When choosing the external amplifier, take into account the variation in impedance generated by the DAC on the amplifier's inverting input node. Access is provided to the VREF, RFB, and IOUT1 terminals of the DAC, making the device extremely versatile and allowing it to be configured in several operating modes; for example, it can provide a unipolar output or can provide 4-quadrant multiplication in bipolar mode. Note that a matching switch is used in series with the internal RFB feedback resistor. If users attempt to measure RFB, power must be applied to VDD to achieve continuity. CIRCUIT OPERATION Unipolar Mode Using a single op amp, these devices can easily be configured to provide a 2-quadrant multiplying operation or a unipolar output voltage swing, as shown in Figure 43. When an output amplifier is connected in unipolar mode, the output voltage is given by VOUT = - These DACs are designed to operate with either negative or positive reference voltages. The VDD power pin is only used by the internal digital logic to drive the on and off states of the DAC switches. These DACs are designed to accommodate ac reference input signals in the range of -10 V to +10 V. With a fixed 10 V reference, the circuit shown in Figure 43 gives a unipolar 0 V to -10 V output voltage swing. When VIN is an ac signal, the circuit performs 2-quadrant multiplication. Table 5 shows the relationship between the digital code and the expected output voltage for a unipolar operation using the 8-bit AD5450. Table 5. Unipolar Code Table for the AD5450 Digital Input 1111 1111 1000 0000 0000 0001 0000 0000 D x V REF 2n where: D is the fractional representation of the digital word loaded to the DAC. D = 0 to 255 (8-bit AD5450). = 0 to 1023 (10-bit AD5451). = 0 to 4095 (12-bit AD5452). = 0 to 16,383 (14-bit AD5453). n is the number of bits. Rev. C | Page 16 of 28 Analog Output (V) -VREF (255/256) -VREF (128/256) = -VREF/2 -VREF (1/256) -VREF (0/256) = 0 AD5450/AD5451/AD5452/AD5453 Bipolar Mode When VIN is an ac signal, the circuit performs 4-quadrant multiplication. Table 6 shows the relationship between the digital code and the expected output voltage for a bipolar operation using the 8-bit AD5450. In some applications, it may be necessary to generate a full 4-quadrant multiplying operation or a bipolar output swing. This can be easily accomplished by using another external amplifier and some external resistors, as shown in Figure 44. In this circuit, the second amplifier, A2, provides a gain of 2. Biasing the external amplifier with an offset from the reference voltage results in full 4-quadrant multiplying operation. The transfer function of this circuit shows that both negative and positive output voltages are created as the input data (D) is incremented from Code 0 (VOUT = - VREF) to midscale (VOUT - 0 V ) to full scale (VOUT = +VREF). Table 6. Bipolar Code Table for the AD5450 Digital Input 1111 1111 1000 0000 0000 0001 0000 0000 Analog Output (V) +VREF (127/128) 0 -VREF (127/128) -VREF (128/128) D VOUT = VREF x n -1 - VREF 2 where: D is the fractional representation of the digital word loaded to the DAC. D = 0 to 255 (8-bit AD5450). = 0 to 1023 (10-bit AD5451). = 0 to 4095 (12-bit AD5452). n is the resolution of the DAC. R3 20k VDD VDD VREF 10V R1 VREF R5 20k R2 AD5450/ AD5451/ AD5452/ AD5453 C1 RFB IOUT1 A1 R4 10k A2 GND VOUT = -VREF TO +VREF SYNC SCLK SDIN AGND Figure 44. Bipolar Mode Operation (4-Quadrant Multiplication) Rev. C | Page 17 of 28 04587-010 CONTROLLER NOTES 1. R1 AND R2 USED ONLY IF GAIN ADJUSTMENT IS REQUIRED. ADJUST R1 FOR VOUT = 0V WITH CODE 10000000 LOADED TO DAC. 2. MATCHING AND TRACKING IS ESSENTIAL FOR RESISTOR PAIRS R3 AND R4. 3. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1/A2 IS A HIGH SPEED AMPLIFIER. AD5450/AD5451/AD5452/AD5453 Stability Positive Output Voltage In the I-to-V configuration, the IOUT of the DAC and the inverting node of the op amp must be connected as close as possible, and proper PCB layout techniques must be employed. Because every code change corresponds to a step function, gain peaking may occur if the op amp has limited gain bandwidth product (GBP) and there is excessive parasitic capacitance at the inverting node. This parasitic capacitance introduces a pole into the open-loop response, which can cause ringing or instability in the closed-loop applications circuit. The output voltage polarity is opposite to the VREF polarity for dc reference voltages. To achieve a positive voltage output, an applied negative reference to the input of the DAC is preferred over the output inversion through an inverting amplifier because of the resistors' tolerance errors. To generate a negative reference, the reference can be level-shifted by an op amp such that the VOUT and GND pins of the reference become the virtual ground and -2.5 V, respectively, as shown in Figure 46. ADR03 An optional compensation capacitor, C1, can be added in parallel with RFB for stability, as shown in Figure 43 and Figure 44. Too small a value of C1 can produce ringing at the output, and too large a value can adversely affect the settling time. C1 should be found empirically, but 1 pF to 2 pF is generally adequate for the compensation. SINGLE-SUPPLY APPLICATIONS Figure 45 shows these DACs operating in the voltage-switching mode. The reference voltage, VIN, is applied to the IOUT1 pin, and the output voltage is available at the VREF terminal. In this configuration, a positive reference voltage results in a positive output voltage, making single-supply operation possible. The output from the DAC is voltage at a constant impedance (the DAC ladder resistance); therefore, an op amp is necessary to buffer the output voltage. The reference input no longer sees constant input impedance, but one that varies with code; therefore, the voltage input should be driven from a low impedance source. RFB VIN R1 R2 VDD IOUT1 VIN GND +5V VDD -2.5V C1 RFB IOUT1 VREF VOUT = 0V TO +2.5V GND -5V VREF VOUT 04587-012 NOTES 1. ADDITIONAL PINS OMITTED FOR CLARITY. 2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER. Voltage-Switching Mode VDD VOUT VDD = +5V Figure 46. Positive Output Voltage with Minimum Components ADDING GAIN In applications in which the output voltage is required to be greater than VIN, gain can be added with an additional external amplifier, or it can be achieved in a single stage. It is important to consider the effect of the temperature coefficients of the DAC's thin film resistors. Simply placing a resistor in series with the RFB resistor causes mismatches in the temperature coefficients and results in larger gain temperature coefficient errors. Instead, increase the gain of the circuit by using the recommended configuration shown in Figure 47. R1, R2, and R3 should have similar temperature coefficients, but they need not match the temperature coefficients of the DAC. This approach is recommended in circuits where gains greater than 1 are required. GND NOTES 1. ADDITIONAL PINS OMITTED FOR CLARITY. 2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER. 04587-011 VDD VDD Figure 45. Single-Supply Voltage-Switching Mode VIN R1 C1 RFB IOUT1 VREF VOUT R3 GND R2 GAIN = R2 + R3 R2 R2R3 R1 = NOTES R2 + R3 1. ADDITIONAL PINS OMITTED FOR CLARITY. 2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER. Rev. C | Page 18 of 28 Figure 47. Increasing Gain of Current-Output DAC 04587-013 It is important to note that with this configuration VIN is limited to low voltages because the switches in the DAC ladder do not have the same source-drain drive voltage. As a result, their on resistance differs, which degrades the integral linearity of the DAC. Also, VIN must not go negative by more than 0.3 V, or an internal diode turns on, causing the device to exceed the maximum ratings. In this type of application, the full range of multiplying capability of the DAC is lost. AD5450/AD5451/AD5452/AD5453 DIVIDER OR PROGRAMMABLE GAIN ELEMENT REFERENCE SELECTION Current-steering DACs are very flexible and lend themselves to many different applications. If this type of DAC is connected as the feedback element of an op amp and RFB is used as the input resistor as shown in Figure 48, the output voltage is inversely proportional to the digital input fraction, D. When selecting a reference for use with this series of currentoutput DACs, pay attention to the reference's output voltage temperature coefficient specification. This parameter not only affects the full-scale error, but also may affect the linearity (INL and DNL) performance. The reference temperature coefficient should be consistent with the system accuracy specifications. For example, an 8-bit system is required to hold its overall specification to within 1 LSB over the temperature range 0C to 50C, and the system's maximum temperature drift should be less than 78 ppm/C. For D = 1 - 2-n, the output voltage is VOUT = -V IN -V IN = (1 - 2 -n ) D As D is reduced, the output voltage increases. For small values of the digital fraction, D, it is important to ensure that the amplifier does not saturate and that the required accuracy is met. For example, an 8-bit DAC driven with the binary code 0x10 (00010000), that is, 16 decimal, in the circuit of Figure 48 should cause the output voltage to be 16 times VIN. AMPLIFIER SELECTION VDD VIN RFB The primary requirement for the current-steering mode is an amplifier with low input bias currents and low input offset voltage. The input offset voltage of an op amp is multiplied by the variable gain of the circuit due to the code-dependent output resistance of the DAC. A change in this noise gain between two adjacent digital fractions produces a step change in the output voltage due to the offset voltage of the amplifier's input. This output voltage change is superimposed on the desired change in output between the two codes and gives rise to a differential linearity error, which if large enough, could cause the DAC to be nonmonotonic. VDD IOUT1 A 12-bit system within 2 LSB accuracy requires a maximum drift of 10 ppm/C. Choosing a precision reference with a low output temperature coefficient minimizes this error source. Table 7 lists some dc references available from Analog Devices that are suitable for use with this range of current-output DACs. VREF GND NOTE ADDITIONAL PINS OMITTED FOR CLARITY 04587-014 VOUT Figure 48. Current-Steering DAC Used as a Divider or Programmable Gain Element However, if the DAC has a linearity specification of 0.5 LSB, D can have weight anywhere in the range of 15.5/256 to 16.5/256. Therefore, the possible output voltage is in the range of 15.5 VIN to 16.5 VIN--an error of 3%, even though the DAC itself has a maximum error of 0.2%. DAC leakage current is also a potential error source in divider circuits. The leakage current must be counterbalanced by an opposite current supplied from the op amp through the DAC. Because only a fraction, D, of the current in the VREF terminal is routed to the IOUT1 terminal, the output voltage changes as follows: Output Error Voltage Due to Leakage = (Leakage x R)/D where R is the DAC resistance at the VREF terminal. For a DAC leakage current of 10 nA, R = 10 k, and a gain (that is, 1/D) of 16, the error voltage is 1.6 mV. The input bias current of an op amp generates an offset at the voltage output as a result of the bias current flowing in the feedback resistor, RFB. Most op amps have input bias currents low enough to prevent significant errors in 12-bit applications. However, for 14-bit applications, some consideration should be given to selecting an appropriate amplifier. Common-mode rejection of the op amp is important in voltageswitching circuits because it produces a code-dependent error at the voltage output of the circuit. Most op amps have adequate common-mode rejection for use at 8-, 10-, and 12-bit resolutions. Provided that the DAC switches are driven from true wideband low impedance sources (VIN and AGND), they settle quickly. Consequently, the slew rate and settling time of a voltageswitching DAC circuit is determined largely by the output op amp. To obtain minimum settling time in this configuration, it is important to minimize capacitance at the VREF node (the voltage output node in this application) of the DAC. This is done by using low input-capacitance buffer amplifiers and careful board design. Most single-supply circuits include ground as part of the analog signal range, which in turn requires an amplifier that can handle rail-to-rail signals. There is a large range of single-supply amplifiers available from Analog Devices. Rev. C | Page 19 of 28 AD5450/AD5451/AD5452/AD5453 Table 7. Suitable ADI Precision References Part No. ADR01 ADR01 ADR02 ADR02 ADR03 ADR03 ADR06 ADR06 ADR431 ADR435 ADR391 ADR395 Output Voltage (V) 10 10 5 5 2.5 2.5 3 3 2.5 5 2.5 5 Initial Tolerance (%) 0.05 0.05 0.06 0.06 0.10 0.10 0.10 0.10 0.04 0.04 0.16 0.10 Temp Drift (ppm/C) 3 9 3 9 3 9 3 9 3 3 9 9 ISS (mA) 1 1 1 1 1 1 1 1 0.8 0.8 0.12 0.12 Output Noise (V p-p) 20 20 10 10 6 6 10 10 3.5 8 5 8 Package SOIC-8 TSOT-23, SC70 SOIC-8 TSOT-23, SC70 SOIC-8 TSOT-23, SC70 SOIC-8 TSOT-23, SC70 SOIC-8 SOIC-8 TSOT-23 TSOT-23 Table 8. Suitable ADI Precision Op Amps Part No. OP97 OP1177 AD8551 AD8603 AD8628 Supply Voltage (V) 2 to 20 2.5 to 15 2.7 to 5 1.8 to 6 2.7 to 6 VOS (Max) (V) 25 60 5 50 5 IB (Max) (nA) 0.1 2 0.05 0.001 0.1 0.1 Hz to 10 Hz Noise (V p-p) 0.5 0.4 1 2.3 0.5 Supply Current (A) 600 500 975 50 850 Package SOIC-8 MSOP, SOIC-8 MSOP, SOIC-8 TSOT TSOT, SOIC-8 Table 9. Suitable ADI High Speed Op Amps Part No. AD8065 AD8021 AD8038 AD9631 Supply Voltage (V) 5 to 24 2.5 to 12 3 to 12 3 to 6 BW @ ACL (MHz) 145 490 350 320 Slew Rate (V/s) 180 120 425 1300 Rev. C | Page 20 of 28 VOS (Max) (V) 1500 1000 3000 10000 IB (Max) (nA) 0.006 10500 750 7000 Package SOIC-8, SOT-23, MSOP SOIC-8, MSOP SOIC-8, SC70-5 SOIC-8 AD5450/AD5451/AD5452/AD5453 DB15 (MSB) The AD5450/AD5451/AD5452/AD5453 have an easy-to-use 3-wire interface that is compatible with SPI, QSPI, MICROWIRE, and most DSP interface standards. Data is written to the device in 16-bit words. This 16-bit word consists of two control bits and 8, 10, 12, or 14 data bits, as shown in Figure 49, Figure 50, Figure 51, and Figure 52. The AD5453 uses all 14 bits of DAC data, the AD5452 uses 12 bits and ignores the two LSBs, the AD5451 uses 10 bits and ignores the four LSBs, and the AD5450 uses 8 bits and ignores the six LSBs. DAC Control Bits C1, C0 Control Bits C1 and C0 allow the user to load and update the new DAC code and to change the active clock edge. By default, the shift register clocks data upon the falling edge; this can be changed via the control bits. If changed, the DAC core is inoperative until the next data frame, and a power recycle is required to return it to active on the falling edge. A power cycle resets the core to default condition. On-chip power-on reset circuitry ensures that the device powers on with zero scale loaded to the DAC register and IOUT line. CONTROL BITS Figure 51. AD5452 12-Bit Input Shift Register Contents DB15 (MSB) C1 After the falling edge of the 16th SCLK pulse, bring SYNC high to transfer data from the input shift register to the DAC register. DB0 (LSB) X X X X X X 04587-005 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 DATA BITS CONTROL BITS Figure 49. AD5450 8-Bit Input Shift Register Contents DB15 (MSB) DATA BITS Figure 52. AD5453 14-Bit Input Shift Register Contents MICROPROCESSOR INTERFACING Microprocessor interfacing to a AD5450/AD5451/AD5452/ AD5453 DAC is through a serial bus that uses standard protocol and is compatible with microcontrollers and DSP processors. The communication channel is a 3-wire interface consisting of a clock signal, a data signal, and a synchronization signal. The AD5450/AD5451/AD5452/AD5453 require a 16-bit word, with the default being data valid upon the falling edge of SCLK, but this is changeable using the control bits in the data-word. ADSP-21xx-to-AD5450/AD5451/AD5452/AD5453 Interface C0 AD5450/AD5451/ AD5452/AD5453* DB0 (LSB) DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 X X DATA BITS CONTROL BITS X SPIxSEL SYNC MOSI SDIN SCK SCLK *ADDITIONAL PINS OMITTED FOR CLARITY Figure 53. ADSP-2191 SPI-to-AD5450/AD5451/AD5452/AD5453 Interface A serial interface between the DAC and DSP SPORT is shown in Figure 54. In this example, SPORT0 is used to transfer data to the DAC shift register. Transmission is initiated by writing a word to the Tx register after the SPORT has been enabled. In a write sequence, data is clocked out upon each rising edge of the DSP's serial clock and clocked into the DAC input shift register upon the falling edge of its SCLK. The update of the DAC output takes place upon the rising edge of the SYNC signal. ADSP-2101/ ADSP-2103/ ADSP-2191* X 04587-006 C1 DB0 (LSB) DB13 DB12 DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 ADSP-2191* SYNC is an edge-triggered input that acts as a framesynchronization signal and chip enable. Data can only be transferred to the device while SYNC is low. To start the serial data transfer, SYNC should be taken low, observing the minimum SYNC falling to SCLK falling edge setup time, t4. To minimize the power consumption of the device, the interface powers up fully only when the device is being written to, that is, upon the falling edge of SYNC. The SCLK and SDIN input buffers are powered down upon the rising edge of SYNC. C0 C0 CONTROL BITS SYNC Function C1 X 04587-100 Function Implemented Load and update (power-on default) Reserved Reserved Clock data to shift register upon rising edge DB15 (MSB) X DATA BITS AD5450/AD5451/ AD5452/AD5453* TFS SYNC DT SDIN SCLK SCLK Figure 50. AD5451 10-Bit Input Shift Register Contents *ADDITIONAL PINS OMITTED FOR CLARITY Figure 54. ADSP-2101/ADSP-2103/ADSP-2191 SPORT-to-AD5450/AD5451/AD5452/AD5453 Interface Rev. C | Page 21 of 28 04587-051 C0 0 1 0 1 DB0 (LSB) DB11 DB10 DB9 DB8 DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 The ADSP-21xx family of DSPs is easily interfaced to a AD5450/ AD5451/AD5452/AD5453 DAC without the need for extra glue logic. Figure 53 is an example of an SPI interface between the DAC and the ADSP-2191M. SCK of the DSP drives the serial data line, SDIN. SYNC is driven from one of the port lines, in this case SPIxSEL. Table 10. DAC Control Bits C1 0 0 1 1 C0 04587-007 C1 04587-008 SERIAL INTERFACE AD5450/AD5451/AD5452/AD5453 Table 11. SPORT Control Register Setup Setting 1 1 00 1 1 1 1111 AD5450/AD5451/ AD5452/AD5453* Figure 56. ADSP-BF5xx SPORT-to-AD5450/AD5451/AD5452/AD5453 Interface SCLK *ADDITIONAL PINS OMITTED FOR CLARITY AD5450/AD5451/ AD5452/AD5453* 8051* 04587-102 SCK SCLK *ADDITIONAL PINS OMITTED FOR CLARITY SYNC SDIN SDIN To load data correctly to the DAC, P1.1 is left low after the first eight bits are transmitted, and a second write cycle is initiated to transmit the second byte of data. Data on RxD is clocked out of the microcontroller upon the rising edge of TxD and is valid upon the falling edge. As a result, no glue logic is required between the DAC and microcontroller interface. P1.1 is taken high following the completion of this cycle. The 80C51/80L51 provide the LSB of its SBUF register as the first bit in the data stream. The DAC input register acquires its data with the MSB as the first bit received. The transmit routine should take this into account. The ADSP-BF5xx family of processors has an SPI-compatible port that enables the processor to communicate with SPIcompatible devices. A serial interface between the BlackFin(R) processor and the AD5450/AD5451/AD5452/AD5453 DAC is shown in Figure 55. In this configuration, data is transferred through the MOSI (master output, slave input) pin. SYNC is driven by the SPIxSEL pin, which is a reconfigured programmable flag pin. MOSI DT SCLK A serial interface between the DAC and the 80C51/80L51 is shown in Figure 57. TxD of the 80C51/80L51 drives SCLK of the DAC serial interface, and RxD drives the serial data line, SDIN. P1.1 is a bit-programmable pin on the serial port and is used to drive SYNC. As data is transmitted to the switch, P1.1 is taken low. The 80C51/80L51 transmit data only in 8-bit bytes; therefore, only eight falling clock edges occur in the transmit cycle. ADSP-BF5xx-to-AD5450/AD5451/AD5452/AD5453 Interface SPIxSEL SYNC 80C51/80L51-to-AD5450/AD5451/AD5452/AD5453 Interface Description Alternate framing Active low frame signal Right justify data Internal serial clock Frame every word Internal framing signal 16-bit data-word ADSP-BF5xx* TFS Figure 55. ADSP-BF5xx-to-AD5450/AD5451/AD5452/AD5453 Interface The ADSP-BF5xx processor incorporates channel synchronous serial ports (SPORT). A serial interface between the DAC and the DSP SPORT is shown in Figure 56. When the SPORT is enabled, initiate transmission by writing a word to the Tx register. The data is clocked out upon each rising edge of the DSP's serial clock and clocked into the DAC's input shift register upon the falling edge its SCLK. The DAC output is updated by using the transmit frame synchronization (TFS) line to provide a SYNC signal. TxD SCLK RxD SDIN P1.1 SYNC *ADDITIONAL PINS OMITTED FOR CLARITY 04587-104 Name TFSW INVTFS DTYPE ISCLK TFSR ITFS SLEN AD5450/AD5451/ AD5452/AD5453* ADSP-BF5xx* 04587-103 Communication between two devices at a given clock speed is possible when the following specifications are compatible: frame SYNC delay and frame SYNC setup-and-hold, data delay and data setup-and-hold, and SCLK width. The DAC interface expects a t4 (SYNC falling edge to SCLK falling edge setup time) of 13 ns minimum. See the ADSP-21xx User Manual for information on clock and frame SYNC frequencies for the SPORT register. Table 11 shows the setup for the SPORT control register. Figure 57. 80C51/80L51-to-AD5450/AD5451/AD5452/AD5453 Interface MC68HC11-to-AD5450/AD5451/AD5452/AD5453 Interface Figure 58 is an example of a serial interface between the DAC and the MC68HC11 microcontroller. The serial peripheral interface (SPI) on the MC68HC11 is configured for master mode (MSTR) = 1, clock polarity bit (CPOL) = 0, and clock phase bit (CPHA) = 1. The SPI is configured by writing to the SPI control register (SPCR); see the 68HC11 User Manual. SCK of the 68HC11 drives the SCLK of the DAC interface; the MOSI output drives the serial data line (SDIN) of the DAC. Rev. C | Page 22 of 28 AD5450/AD5451/AD5452/AD5453 AD5450/AD5451/ AD5452/AD5453* PC7 SYNC SCK SCLK MOSI SDIN 04587-105 MC68HC11* *ADDITIONAL PINS OMITTED FOR CLARITY Figure 58. MC68HC11-to-AD5450/AD5451/AD5452/AD5453 Interface If the user wants to verify the data previously written to the input shift register, the SDO line can be connected to MISO of the MC68HC11. In this configuration with SYNC low, the shift register clocks data out upon the rising edges of SCLK. MICROWIRE-to-AD5450/AD5451/AD5452/AD5453 Interface Figure 59 shows an interface between the DAC and any MICROWIRE-compatible device. Serial data is shifted out upon the falling edge of the serial clock, SK, and is clocked into the DAC input shift register upon the rising edge of SK, which corresponds to the falling edge of the DAC's SCLK. AD5450/AD5451/ AD5452/AD5453* SK SCLK SO SDIN CS SYNC *ADDITIONAL PINS OMITTED FOR CLARITY AD5450/AD5451/ AD5452/AD5453* SCK/RC3 SCLK SDI/RC4 SDIN RA1 SYNC *ADDITIONAL PINS OMITTED FOR CLARITY Figure 60. PIC16C6x/7x-to-AD5450/AD5451/AD5452/AD5453 Interface PCB LAYOUT AND POWER SUPPLY DECOUPLING In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The printed circuit board on which a AD5450/AD5451/AD5452/AD5453 DAC is mounted should be designed so that the analog and digital sections are separated and confined to certain areas of the board. If the DAC is in a system where multiple devices require an AGND-to-DGND connection, the connection should be made at one point only. The star ground point should be established as close as possible to the device. These DACs should have ample supply bypassing of 10 F in parallel with 0.1 F on the supply located as close to the package as possible, ideally right up against the device. The 0.1 F capacitor should have low effective series resistance (ESR) and low effective series inductance (ESI), like the common ceramic types that provide a low impedance path to ground at high frequencies, to handle transient currents due to internal logic switching. Low ESR 1 F to 10 F tantalum or electrolytic capacitors should also be applied at the supplies to minimize transient disturbance and filter out low frequency ripple. Components, such as clocks, that produce fast switching signals should be shielded with a digital ground to avoid radiating noise to other parts of the board, and they should never be run near the reference inputs. 04587-106 MICROWIRE* PIC16C6x/PIC16C7x* 04587-107 The SYNC signal is derived from a port line (PC7). When data is being transmitted to the AD5450/AD5451/AD5452/AD5453, the SYNC line is taken low (PC7). Data appearing on the MOSI output is valid upon the falling edge of SCK. Serial data from the 68HC11 is transmitted in 8-bit bytes with only eight falling clock edges occurring in the transmit cycle. Data is transmitted MSB first. To load data to the DAC, PC7 is left low after the first eight bits are transferred, and a second serial write operation is performed to the DAC. PC7 is taken high at the end of this procedure. Figure 59. MICROWIRE-to-AD5450/AD5451/AD5452/AD5453 Interface PIC16C6x/PIC16C7x-toAD5450/AD5451/AD5452/AD5453 Interface The PIC16C6x/PIC16C7x synchronous serial port (SSP) is configured as an SPI master with the clock polarity bit (CKP) = 0. This is done by writing to the synchronous serial port control register (SSPCON); see the PIC16/PIC17 Microcontroller User Manual. In this example, I/O Port RA1 is used to provide a SYNC signal and enable the serial port of the DAC. This microcontroller transfers only eight bits of data during each serial transfer operation; therefore, two consecutive write operations are required. Figure 60 shows the connection diagram. Avoid crossover of digital and analog signals. Traces on opposite sides of the board should run at right angles to each other. This reduces the effects of feedthrough through the board. A microstrip technique is the best solution, but its use is not always possible with a double-sided board. In this technique, the component side of the board is dedicated to the ground plane and signal traces are placed on the solder side. It is good practice to employ compact, minimum lead length PCB layout design. Leads to the input should be as short as possible to minimize IR drops and stray inductance. The PCB metal traces between VREF and RFB should also be matched to minimize gain error. To optimize high frequency performance, the I-to-V amplifier should be located as close to the device as possible. Rev. C | Page 23 of 28 AD5450/AD5451/AD5452/AD5453 EVALUATION BOARD FOR THE DAC POWER SUPPLIES FOR THE EVALUATION BOARD The evaluation board consists of an AD5450, AD5451, AD5452, or AD5453 DAC and a current-to-voltage amplifier, such as an AD8065. Included on the evaluation board is a 10 V reference, ADR01. An external reference can also be applied via an SMB input. The board requires 12 V and +5 V supplies. The +12 V VDD and -12 V VSS are used to power the output amplifier; the +5 V is used to power the DAC (VDD1) and transceivers (VCC). Both supplies are decoupled to their respective ground plane with 10 F tantalum and 0.1 F ceramic capacitors. The evaluation kit consists of a CD with PC software to control the DAC. The software allows the user to write code to the device. U1 R1 10k P1-3 J3 SCLK SCLK 6 RFB SDIN SDIN 5 SDIN IOUT1 J5 GND SYNC P1-19 P1-20 P1-21 P1-22 P1-23 P1-24 P1-25 P1-26 P1-27 P1-28 P1-29 P1-30 SYNC 4 C2 10F AD8065AR C6 1.8pF 8 2 7 3 VREF VREF J2 2 VDD 3 VDD P2-3 P2-2 C3 10F + C4 0.1F 5 C11 + C12 0.1F 10F C13 + C14 0.1F 10F + U3 1 SYNC VREF C7 10F VSS 3 VIN VOUT U2 TRIM C7 0.1F V- 6 V+ C9 7 10F 4 VDD + LK1 C10 0.1F TP VOUT J1 4 1 C5 0.1F GND 2 AGND P2-1 VSS P2-4 VDD1 C15 + C16 0.1F 10F 04587-056 P1-4 C1 + 0.1F VDD SCLK J4 P1-2 VDD1 AD5450/ AD5451/ AD5452/ AD5453 VDD1 Figure 61. Schematic of AD5450/AD5451/AD5452/AD5453 Evaluation Board Rev. C | Page 24 of 28 04587-057 AD5450/AD5451/AD5452/AD5453 04587-058 Figure 62. Component-Side Artwork Figure 63. Silkscreen--Component-Side View (Top) Rev. C | Page 25 of 28 04587-059 AD5450/AD5451/AD5452/AD5453 Figure 64. Solder-Side Artwork Table 12. Overview of AD54xx and AD55xx Devices Part No. AD5424 AD5426 AD5428 AD5429 AD5450 AD5432 AD5433 AD5439 AD5440 AD5451 AD5443 AD5444 AD5415 AD5405 AD5445 AD5447 AD5449 AD5452 AD5446 AD5453 AD5553 AD5556 AD5555 AD5557 AD5543 AD5546 AD5545 AD5547 1 Resolution 8 8 8 8 8 10 10 10 10 10 12 12 12 12 12 12 12 12 14 14 14 14 14 14 16 16 16 16 No. DACs 1 1 2 2 1 1 1 2 2 1 1 1 2 2 2 2 2 1 1 1 1 1 2 2 1 1 2 2 INL (LSB) 0.25 0.25 0.25 0.25 0.25 0.5 0.5 0.5 0.5 0.25 1 0.5 1 1 1 1 1 0.5 1 2 1 1 1 1 2 2 2 2 Interface Parallel Serial Parallel Serial Serial Serial Parallel Serial Parallel Serial Serial Serial Serial Parallel Parallel Parallel Serial Serial Serial Serial Serial Parallel Serial Parallel Serial Parallel Serial Parallel Package 1 RU-16, CP-20 RM-10 RU-20 RU-10 UJ-8 RM-10 RU-20, CP-20 RU-16 RU-24 UJ-8 RM-10 RM-10 RU-24 CP-40 RU-20, CP-20 RU-24 RU-16 UJ-8, RM-8 RM-10 UJ-8, RM-8 RM-8 RU-28 RM-8 RU-38 RM-8 RU-28 RU-16 RU-38 RU = TSSOP, CP = LFCSP, RM = MSOP, UJ = TSOT. Rev. C | Page 26 of 28 Features 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 50 MHz serial 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 50 MHz serial 12 MHZ BW, 50 MHz serial interface 10 MHz BW, 50 MHz serial 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 50 MHz serial 10 MHz BW, 17 ns CS pulse width 12 MHz BW, 50 MHz serial interface 10 MHz BW, 50 MHz serial 12 MHz BW, 50 MHz serial 10 MHz BW, 50 MHz serial 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 17 ns CS pulse width 10 MHz BW, 50 MHz serial 12 MHz BW, 50 MHz serial interface 12 MHz BW, 50 MHz serial 12 MHz BW, 50 MHz serial 4 MHz BW, 50 MHz serial clock 4 MHz BW, 20 ns WR pulse width 4 MHz BW, 50 MHz serial clock 4 MHz BW, 20 ns WR pulse width 4 MHz BW, 50 MHz serial clock 4 MHz BW, 20 n WR pulse width 4 MHz BW, 50 MHz serial clock 4 MHz BW, 20 ns WR pulse width AD5450/AD5451/AD5452/AD5453 OUTLINE DIMENSIONS 2.90 BSC 8 7 6 5 1 2 3 4 2.80 BSC 1.60 BSC PIN 1 INDICATOR 0.65 BSC 1.95 BSC *0.90 0.87 0.84 *1.00 MAX 0.10 MAX 0.38 0.22 0.20 0.08 0.60 0.45 0.30 8 4 0 SEATING PLANE *COMPLIANT TO JEDEC STANDARDS MO-193-BA WITH THE EXCEPTION OF PACKAGE HEIGHT AND THICKNESS. Figure 65. 8-Lead Thin Small Outline Transistor Package [TSOT] (UJ-8) Dimensions shown in millimeters 3.20 3.00 2.80 3.20 3.00 2.80 8 1 5.15 4.90 4.65 5 4 PIN 1 IDENTIFIER 0.65 BSC 0.95 0.85 0.75 15 MAX 1.10 MAX 0.40 0.25 6 0 0.23 0.09 COMPLIANT TO JEDEC STANDARDS MO-187-AA Figure 66. 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters Rev. C | Page 27 of 28 0.80 0.55 0.40 100709-B 0.15 0.05 COPLANARITY 0.10 AD5450/AD5451/AD5452/AD5453 ORDERING GUIDE Model 1 AD5450YUJZ-REEL AD5450YUJZ-REEL7 AD5451YUJZ-REEL AD5451YUJZ-REEL7 AD5452YUJZ-REEL AD5452YUJZ-REEL7 AD5452YRM AD5452YRM-REEL AD5452YRMZ AD5452YRMZ-REEL AD5452YRMZ-REEL7 AD5453YUJZ-REEL AD5453YUJZ-REEL7 AD5453YRM AD5453YRM-REEL AD5453YRM-REEL7 AD5453YRMZ AD5453YRMZ-REEL AD5453YRMZ-REEL7 EVAL-AD5450EB EVAL-AD5451EBZ EVAL-AD5452EBZ EVAL-AD5453EBZ 1 Resolution 8 8 10 10 12 12 12 12 12 12 12 14 14 14 14 14 14 14 14 INL 0.25 0.25 0.25 0.25 0.5 0.5 0.5 0.5 0.5 0.5 0.5 2 2 2 2 2 2 2 2 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C Z = RoHS Compliant Part. (c)2005-2010 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D04587-0-1/10(C) Rev. C | Page 28 of 28 Package Description 8-Lead TSOT 8-Lead TSOT 8-Lead TSOT 8-Lead TSOT 8-Lead TSOT 8-Lead TSOT 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead TSOT 8-Lead TSOT 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP Evaluation Kit Evaluation Kit Evaluation Kit Evaluation Kit Package Option UJ-8 UJ-8 UJ-8 UJ-8 UJ-8 UJ-8 RM-8 RM-8 RM-8 RM-8 RM-8 UJ-8 UJ-8 RM-8 RM-8 RM-8 RM-8 RM-8 RM-8 Branding D6Y D6Y D6Z D6Z D70 D70 D1Z D1Z D70 D70 D70 DAH DAH D26 D26 D26 DAH DAH DAH