AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function Features General Description AP1118 is a low dropout positive fixed-mode regulator with minimum of 1A output current capability. The product is specifically designed to provide well-regulated supply for low voltage IC applications such as high-speed bus termination and low current 3.3V logic supply. AP1118 is also well suited for other applications such as VGA cards. AP1118 is guaranteed to have <1.4V dropout at full load current making it ideal to provide well regulated outputs of 1.25 to 12V with up to 18V input supply. The AP1118 offers a TTL - Logic compatible enable pin. *1.4V maximum dropout at full load current transient response *Output current limiting *Built-in thermal shutdown *Packages: TO220-5, TO252-5, TO263-5, SOP8 *Good noise rejection *Fixed Output 1.5V, 1.8V, 2.5V, 3.3V, 5.0V, 9.0V, 12V *Enable function *Fast Applications * * * PC peripheral Communication CDROM.. Ordering Information AP 1118 X XX X X Low Dropout Regulator Vout Package 15 : 1.5V 18 : 1.8V 25 : 2.5V 33 : 3.3V 50 : 5.0V 90 : 9.0V 12 : 12V D : TO252-5L T : TO220-5L K : TO263-5L S : SOP-8L Lead Free Blank : Normal L : Lead Free Package Packing Blank : Tube A : Taping Typical Circuit 5V C1 100uF Vin EN Tab is Vout Vout 3.3V/1A NC C2 100uF GND ( 5V/3.3V fixed output ) This datasheet contains new product information. Anachip Corp. reserves the rights to modify the product specification without notice. No liability is assumed as a result of the use of this product. No rights under any patent accompany the sale of the product. Rev. 0.2 1/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function Connection Diagram 5 PIN TO252/TO263 5 PIN TO220 ( Top View ) 5 Vin 4 EN 5 Vin 4 EN 3 Vout 3 Vout 2 NC 2 NC 1 GND 1 GND Tab is Vout Tab is Vout SOP-8L ( Top View ) Vout 5 4 Vin Vout 6 3 EN Vout 7 2 Vout Vout 8 1 GND Pin Descriptions NAME FUNCTION GND Ground. Vout The output of the regulator. A minimum of 10uF capacitor must be connected from this pin to ground to insure stability. Vin The input pin of regulator. Typically a large storage capacitor is connected from this pin to ground to insure that the input voltage does not sag below the minimum dropout voltage during the load transient response. This pin must always be 1.3V higher than Vout in order for the device to regulate properly. EN The input pin of regulator. TTL/CMOS compatible input Logic high = disable output, Logic Low or open = output enable. (internal pull-down resistor~100 K). NC No connection. Anachip Corp. www.anachip.com.tw Rev.0.2 2/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function Absolute Maximum Ratings Characteristics Symbol Values Unit DC Supply Voltage Vin -0.3 to 18 V Enable Pin Voltage VEN 7 V Power Dissipation PD Internally Limited Storage Temperature TST -65 to +150 Operating Junction Temperature Range TOP. 0 to +150 oC oC Electrical Characteristics (Under Operating Conditions) PARAMETER CONDITIONS MIN TYP MAX UNIT 1.470 1.500 1.530 V 1.764 1.800 1.836 V 2.450 2.500 2.550 V 3.235 3.300 3.365 V 4.900 5.000 5.100 V 8.820 9.000 9.180 V 11.760 12.000 12.240 V 0.2 % 12 15 mV 15 18 mV 20 25 mV 26 33 mV 40 50 mV 70 90 mV 100 120 mV 1.3 1.4 V o AP1118-1.5 AP1118-1.8 AP1118-2.5 Output Voltage AP1118-3.3 AP1118-5.0 AP1118-9.0 AP1118-12.0 Line Regulation AP1118-XXX AP1118-1.5 AP1118-1.8 AP1118-2.5 Load Regulation AP1118-3.3 AP1118-5.0 AP1118-9.0 AP1118-12.0 Dropout Voltage (VIN-VOUT) AP1118- 1.5/1.8 2.5/3.3/5.0/9.0/12 IOUT = 10mA, TJ = 25 C, 3VVIN15V o IOUT = 10mA, TJ = 25 C, 3.3VVIN15V o IOUT = 10mA, TJ = 25 C, 4VVIN15V o IOUT = 10mA, TJ = 25 C, 4.8VVIN15V o IOUT = 10mA, TJ = 25 C, 6.5VVIN15V o IOUT = 10mA, TJ = 25 C, 10.5VVIN18V o IOUT = 10mA, TJ = 25 C, 13.5VVIN18V IO=10mA,VOUT+1.5V<VIN<18V, o TJ=25 C VIN=3V, 0mA<Io<1A, o TJ=25 C (Note 1,2) VIN=3.3V, 0mA<Io<1A, o TJ=25 C (Note 1,2) VIN=4V, 0mA<Io<1A, o TJ=25 C (Note 1,2) VIN = 5V, 0IOUT1A, o TJ=25 C (Note 1,2) VIN = 8V, 0IOUT1A, o TJ=25 C (Note 1,2) VIN =12V, 0IOUT1A, o TJ=25 C (Note 1,2) VIN =15V, 0IOUT1A, o TJ=25 C (Note 1,2) IOUT = 1A , VOUT=0.1V Anachip Corp. www.anachip.com.tw Rev.0.2 3/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function Electrical Characteristics(Continued) PARAMETER (Under Operating Conditions) CONDITIONS MIN Current Limit AP1118- 1.5/1.8 2.5/3.3/5.0/9.1/12 (VIN-VOUT) = 5V Minimum Load Current AP1118-XXX 0 CTj125 C VEN Enable Input Voltage IEN Enable Input Current Thermal Regulation TA=25, 30ms pulse Ripple Rejection Temperature Stability o A 5 10 mA 0.8 V 1.6 A 0.008 0.04 %/W F=120Hz,COUT=25uF Tantalum, IOUT=1A AP1118-XXX VIN=VOUT+3V 60 70 dB IO=10mA 0.5 SOP-8L TO-220-5L TO263-5L % 150 102 85 90 TO-252-5L TO-220-5L TO263-5L JC Thermal Resistance TO-252-5L Junction-to-Case UNIT 10 80 JA Thermal Resistance SOP-8L Junction-to-Ambient(No heat sink ;No air flow) MAX 1. 1 o Logic Low (ON) Logic High (OFF) VEN = 0.8V VEN = 2.0V TYP : Control Circuitry/Power Transistor 25 15 0.65/2.7 3.5 O C/W O C/W Note1: See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18" from the package. Note2: Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input/output differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range. Note3: Quiescent current is defined as the minimum output current required to maintain regulation. At 12V input/output differential the device is guaranteed to regulate if the output current is greater than 10mA. Anachip Corp. www.anachip.com.tw Rev.0.2 4/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function Typical Performance Characteristics 0.20 2. 0 Output Voltage Deviation (%) 1. 8 1. 6 Dropout Voltage (V) 1. 4 1. 2 0 I load=800mA -0.20 Tj = 25 oC 1. 0 -0.40 0. 8 Tj = 125 oC 0. 6 -0.80 0. 4 0. 2 0 0 250 750 500 Output Current (mA) -1 1000 -25 Dropout Voltage vs Output Current 0 25 50 Temperature ( oC) 75 100 125 Load Regulation vs Temperature 2 1 Output Voltage Deviation (%) Output Voltage Change (%) 1.5 1 0. 5 0 -0.5 -1 -1.5 -2 -50 -25 0 25 50 Temperature ( oC) 75 100 125 0.8 0.6 0.4 0.2 0 150 2 4 7.5 Cin=1uF Cout=10uF Tantalum 6.5 5.5 40 20 0 -20 -40 0 20 40 60 80 100 120 140 160 180 200 TIME (us) Load Current (A) Output Voltage Deviation (mV) Output Voltage Deviation (mV) Input Voltage (V) Percent Change in Output Voltage vs Temperature Line Transient Response 6 8 10 Input Voltage (V) 12 Line Regulation 30 C in = 1uF C out = 10 uF Tantalum Preload = 100mA 20 10 0 -10 -20 2 1 0 -1 0 10 20 30 40 50 TIME (us) 60 70 80 90 100 Load Transient Response Anachip Corp. www.anachip.com.tw Rev.0.2 5/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function Marking Information (1) TO220-5L ( Top view ) 1118-XX: Voltage 1118-15: 1.5V 1118-18: 1.8V 1118-25: 2.5V 1118-33: 3.3V 1118-50: 5.0V 1118-90: 9.0V 1118-12: 12V AC 1118-XX XX XX X X Logo Blank: normal L: Lead Free Package ID code Xth week: 01~52 Year: "01" = 2001 "02" = 2002 ~ (2) TO252/TO263-5L (Top view) AC 1118- XX XXXX XX Logo Blank: normal L: Lead Free Package ID Code Xth Week: 01~52 Year: "01" = 2001 "02" = 2002 ~ 1118-XX: Voltage 1118-15: 1.5V 1118-18: 1.8V 1118-25: 2.5V 1118-33: 3.3V 1118-50: 5.0V 1118-90: 9.0V 1118-12: 12V (3) SOP-8L (Top view) Logo AC 1118 -XX XX XX X X Blank: normal L: Lead Free Package ID Code Xth week: 01~52 Year: "1" = 2001 "2" = 2002 ~ 1118-XX: Voltage 1118-15: 1.5V 1118-18: 1.8V 1118-25: 2.5V 1118-33: 3.3V 1118-50: 5.0V 1118-50: 9.0V 1118-12: 12V Anachip Corp. www.anachip.com.tw Rev.0.2 6/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function Package Dimension (1) TO220-5 E A F L D H1 Q P b e C J1 e1 Symbol A b C D E e e1 F H1 J1 L Op Q Dimensions In Millimeters Min. Nom. Max. 4.07 4.82 4.45 0.76 0.89 1.02 0.36 0.50 0.64 14.22 14.86 15.50 9.78 10.16 10.54 1.57 1.71 1.85 6.68 6.81 6.93 1.14 1.27 1.40 5.46 6.16 6.86 2.29 2.74 3.18 13.21 13.97 14.73 3.68 3.81 3.94 2.54 2.73 2.92 Anachip Corp. www.anachip.com.tw Dimensions In Inches Min. Nom. Max. 0.160 0.175 0.190 0.030 0.035 0.040 0.014 0.025 0.020 0.560 0.385 0.062 0.263 0.045 0.215 0.090 0.520 0.145 0.100 0.585 0.400 0.067 0.268 0.050 0.243 0.108 0.550 0.150 0.107 0.610 0.415 0.073 0.273 0.055 0.270 0.125 0.580 0.155 0.115 Rev.0.2 7/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function (2) TO252-5 A J H K D M C B L S P(TYP.) Symbol A B C D P S G H J K L M G Dimensions In Millimeters Min. Nom. Max. 6.35 6.60 6.85 5.20 5.35 5.50 6.80 7.00 7.20 2.20 2.50 2.80 1.27 REF. 0.50 0.65 0.80 0.40 0.50 0.60 2.20 2.30 2.40 0.46 0.52 0.58 0.00 0.08 0.15 0.90 1.20 1.50 5.40 5.50 5.59 Anachip Corp. www.anachip.com.tw Dimensions In Inches Min. Nom. Max. 0.250 0.260 0.270 0.205 0.211 0.217 0.268 0.283 0.276 0.087 0.098 0.110 0.050 REF. 0.020 0.026 0.031 0.016 0.087 0.018 0.000 0.035 0.213 0.020 0.091 0.020 0.003 0.047 0.216 0.024 0.094 0.023 0.006 0.059 0.220 Rev.0.2 8/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function (3) TO263-5 A C2 L D L2 E F e Symbol A B C C2 D E e F L L1 L2 C B Dimensions In Millimeters Min. Nom. Max. 4.07 4.46 4.85 0.66 0.84 1.02 0.36 0.50 0.64 1.14 1.27 1.40 8.65 9.15 9.65 9.78 10.16 10.54 1.57 1.71 1.85 6.60 6.86 7.11 14.61 15.24 15.88 2.29 2.54 2.79 2.92 Anachip Corp. www.anachip.com.tw L1 Dimensions In Inches Min. Nom. Max. 0.160 0.176 0.191 0.026 0.033 0.040 0.014 0.020 0.025 0.045 0.050 0.055 0.341 0.360 0.380 0.385 0.400 0.415 0.068 0.073 0.062 0.270 0.280 0.260 0.575 0.600 0.625 0.090 0.100 0.110 0.115 Rev.0.2 9/10 Feb. 10, 2004 AP1118 1A Positive Low Dropout Fixed-Mode Regulator With EN Function H E (4) SOP-8 L VIEW "A" D 0.015x45 7 (4X) e B A1 C A A2 7 (4X) VIEW "A" y Symbol A A1 A2 B C D E e H L y Dimensions In Millimeters Min. Nom. Max. 1.40 1.60 1.75 0.10 0.25 1.30 1.45 1.50 0.33 0.41 0.51 0.19 0.20 0.25 4.80 5.05 5.30 3.70 3.90 4.10 1.27 5.79 5.99 6.20 0.38 0.71 1.27 0.10 8O 0O Anachip Corp. www.anachip.com.tw Dimensions In Inches Min. Nom. Max. 0.055 0.063 0.069 0.040 0.100 0.051 0.057 0.059 0.013 0.016 0.020 0.0075 0.008 0.010 0.189 0.199 0.209 0.146 0.154 0.161 0.050 0.228 0.236 0.244 0.015 0.028 0.050 0.004 0O 8O Rev.0.2 10/10 Feb. 10, 2004