Micrel, Inc. 1849 Fortune Drive San Jose, CA 95131 USA tel + 1 (408) 944-0800 fax + 1 (408) 944-0970 http://www.micrel.com
May 2005 KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
1
KS8001
1.8V, 3.3V 10/100BASETX/FX
Physical Layer Transceiver
DATASHEET V 1.01
General Description
The KS8001 is a 10BASE-T/100BASE-TX/FX Physical
Layer Transceiver, operating the core at 1.8 volts to meet
low voltage and low power requirements. The solution
provides MII/RMII/SMII interfaces to transmit and receive
data. A unique mixed-signal design extends signaling
distance while reducing power consumption.
HP Auto MDI/MDI-X provides the most robust solution for
eliminating the need to differentiate between crossover and
straight-through cables.
Featuring LinkMD cable diagnostics, which allows
detection of common cabling plant problems such as open
and short circuits, the KS8001 represents a new level of
features and performance and is an ideal choice of
physical layer transceiver for 100BASE-TX/10BASE-
T/100BASE-FX applications.
Features
Single chip 100BASE-TX/100BASE-FX/10BASE-T
physical layer solution
1.8V CMOS design, power consumption 250 mW
Robust (130m+) operation over standard cables
Supports Media Independent Interface (MII), Reduced
MII (RMII), and Serial MII (SMII)
LinkMD feature to determine cable length and
diagnose faulty cables up 200 m with +/- 2 m accuracy
Supports HP MDI/MDI-X auto crossover
Supports power down mode and power saving mode
MDC/MDIO to 12.5 MHz for rapid configuration
Fully compliant to IEEE 802.3u standard
Supports auto-negotiation and manual selection for
10/100Mbps speed and full / half-duplex mode
Functional Diagram
LED
DRIVER
LINK
COL
FDX
SPD
MII/RMII/SMII
REGISTERS
AND
CONTROLLER
INTERFACE
TXD3
TXD2
TXC
CRS
COL
RXD3
RXER
RXDV
RXC
TXD1
TXD0
TXER
TXEN
MDIO
MDC
RXD2
RXD1
RXD0
4B/5B ENCODER
SCRAMBLER
PARALLEL/SERIAL
PARALLEL/SERIAL
MANCHESTER ENCODER
4B/5B DECODER
DESCRAMBLER
SERIAL/PARALLEL
MANCHESTER DECODER
SERIAL/PARALLEL
NRZ/NRZI
MLT3 ENCODER
CLOCK
RECOVERY
AUTO
NEGOTIATION
POWER DOWN/
POWER SAVING
PWRDWN
10/100
PULSE
SHAPER
ADAPTIVE EQ
BASELINE WANDER
CORRECTION
MLT3 DECODER
NRZI/NRZ
10BASE-T
RECEIVER
TRANSMITTER
TX+
TX-
RX+
RX-
PLL
XI
XO
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
2
Features (continued)
Configurable through MII serial management ports or via
external control pins
Programmable LED outputs for link, activity, full/half
duplex, collision and speed
On-chip built-in analog front end filtering for both
100BASE-TX and 10BASE-T
Supports back to back, FX to TX for media converter
applications
Single 3.3V power supply with built-in 1.8V regulator (‘L’
parts)
48 Pin LQFP, 48 Pin SSOP, 48 Pin QFN (targeted)
Ordering Information
Part
Number
Temp.
Range Package Lead
Finish
KS8001L 0o–70o C 48-LQFP Standard
KSZ8001L 0o–70o C 48-LQFP Lead-free
KS8001LI - 40o–85o C 48-LQFP Standard
KS8001S 0o–70o C 48-SSOP Standard
KSZ8001S 0o–70o C 48-SSOP Lead-free
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
3
Revision History
Revision Date Summary of Changes
PRELIMINARY 25 Mar 2004
0.8 9 Aug 2004 Updated pin 38 (VDDRCV) definition to 3.3V
Corrected pin configuration diagrams to reflect NC on pins 42 and 43
Updated crystal tolerance to +/- 50 ppm
0.81 17 Sep 2004 Updated series resistance for crystal specification to 40
0.82 25 Jan 2005 LinkMD distance coefficient changed to 0.39
Interrupt register status bits set to RO/SC
Recommended reset circuit added
RMII timing added
1.00 31 Mar 2005 Added lead-free part numbers
1.01 16 May 2005 Changed REXT value to 6.65 K
Removed preliminary status
Added KS8001S to ordering information
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
4
Table of Contents
Pin Description .................................................................................................................................................................................... 6
Strapping Options ............................................................................................................................................................................. 10
Pin Configuration .............................................................................................................................................................................. 11
Functional Description...................................................................................................................................................................... 12
100BASE-TX Transmit .................................................................................................................................................................... 12
100BASE-TX Receive ..................................................................................................................................................................... 12
PLL Clock Synthesizer .................................................................................................................................................................... 12
Scrambler/De-scrambler (100BASE-TX only).................................................................................................................................. 12
10BASE-T Transmit......................................................................................................................................................................... 12
10BASE-T Receive.......................................................................................................................................................................... 12
SQE and Jabber Function (10BASE-T only) ................................................................................................................................... 13
Auto-Negotiation.............................................................................................................................................................................. 13
MII Management Interface................................................................................................................................................................. 13
MII Data Interface ............................................................................................................................................................................ 13
RMII (Reduced MII) Data Interface.................................................................................................................................................... 14
RMII Signal Definition ...................................................................................................................................................................... 14
Reference Clock (REF_CLK)........................................................................................................................................................... 15
Carrier Sense/Receive Data Valid (CRS_DV) ................................................................................................................................. 15
Receive Data [1:0] (RXD[1:0]) ......................................................................................................................................................... 15
Transmit Enable (TX_EN) ............................................................................................................................................................... 15
Transmit Data [1:0] (TXD[1:0])......................................................................................................................................................... 15
Collision Detection........................................................................................................................................................................... 15
RX_ER ............................................................................................................................................................................................ 15
RMII AC Characteristics .................................................................................................................................................................. 16
RMII Transmit Timing ...................................................................................................................................................................... 16
RMII Receive Timing ....................................................................................................................................................................... 16
SMII Signal Definition........................................................................................................................................................................ 17
SMII Signals .................................................................................................................................................................................... 17
Receive Path ................................................................................................................................................................................... 17
Receive Sequence Diagram ............................................................................................................................................................ 17
Transmit Path .................................................................................................................................................................................. 18
Transmit Sequence Diagram ........................................................................................................................................................... 18
Collision Detection........................................................................................................................................................................... 19
DC Specification .............................................................................................................................................................................. 19
Timing Specification ........................................................................................................................................................................ 20
HP Auto Crossover (Auto MDI/MDI-X) ............................................................................................................................................. 21
Auto MDI/MDI-X Cross-Over Transformer Connection.................................................................................................................... 22
Power Management........................................................................................................................................................................... 22
100BT FX Mode.................................................................................................................................................................................. 22
Media converter operation................................................................................................................................................................ 22
LinkMD Cable Diagnostics................................................................................................................................................................ 23
Reference Clock Connection Options ............................................................................................................................................. 24
Register Map ...................................................................................................................................................................................... 25
Register 0h – Basic Control ............................................................................................................................................................. 25
Register 1h – Basic Status .............................................................................................................................................................. 26
Register 2h – PHY Identifier 1 ......................................................................................................................................................... 26
Register 3h – PHY Identifier 2 ......................................................................................................................................................... 26
Register 4h – Auto-Negotiation Advertisement................................................................................................................................ 26
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
5
Register 5h – Auto-Negotiation Link Partner Ability......................................................................................................................... 27
Register 6h – Auto-Negotiation Expansion...................................................................................................................................... 27
Register 7h – Auto-Negotiation Next Page...................................................................................................................................... 28
Register 8h – Link Partner Next Page Ability................................................................................................................................... 28
Register 15h – RXER Counter......................................................................................................................................................... 28
Register 1bh – Interrupt Control/Status Register ............................................................................................................................. 29
Register 1dh – LinkMD Control/Status Register .............................................................................................................................. 29
Register 1eh – PHY Control ............................................................................................................................................................ 30
Register 1fh – 100BASE-TX PHY Controller ................................................................................................................................... 30
Absolute Maximum Rating (Note 1)...................................................................................................................................................... 32
Operating Range (Note 2)...................................................................................................................................................................... 32
Package Thermal Resistance (θJA)(Note 3) .......................................................................................................................................... 33
Electrical Characteristics (Note4) ........................................................................................................................................................ 33
Timing Diagrams ............................................................................................................................................................................... 35
Reset Timing Diagram....................................................................................................................................................................... 40
Reset Timing Parameters................................................................................................................................................................ 40
Reset Circuit Diagram ....................................................................................................................................................................... 40
Reference Circuit for Strapping Option Configuration................................................................................................................... 42
Selection of Isolation Transformers ................................................................................................................................................ 43
Selection of Reference Crystal......................................................................................................................................................... 43
Package Information ......................................................................................................................................................................... 44
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
6
Pin Description
Pin Number Pin Name Type (Note 1) Pin Function
1 MDIO I/O Management Interface (MII) Data I/O
This pin requires an external 10K pull-up resistor.
2 MDC I Management Interface (MII) Clock Input
This pin is synchronous to the MDIO data interface
3 RXD3/
PHYAD1
Ipd/O MII Mode: Receive Data Output[3]2 /
Configuration Mode: The pull-up/pull-down value is latched as PHYADDR[1]
during reset. See “Strapping Options” section for details.
4 RXD2/
PHYAD2
Ipd/O
MII Mode: MII Receive Data Output[2]2 /
Configuration Mode: The pull-up/pull-down value is latched as PHYADDR[2]
during reset. See “Strapping Options” section for details.
5 RXD1/
RXD[1]/
PHYAD3
Ipd/O MII Mode: Receive Data Output[1]2 /
RMII Mode: Receive Data Output[1]3 /
Configuration Mode: The pull-up/pull-down value is latched as PHYADDR[3]
during reset. See “Strapping Options” section for details.
6 RXD0/
RXD[0]/
RX
PHYAD4
Ipd/O MII Mode: Receive Data Output[0]2 /
RMII Mode: Receive Data Output[0]3 /
SMII Mode: Receive Data and Control4 /
Configuration Mode: The pull-up/pull-down value is latched as PHYADDR[4]
during reset. See “Strapping Options” section for details.
7 VDDIO Pwr Digital IO 2.5 /3.3V tolerance power supply.
8 GND Gnd Ground
9 RXDV/
CRSDV/
PCS_LPBK
Ipd/O MII Mode: Receive Data Valid Output /
RMII Mode: Carrier Sense/Receive Data Valid /
Configuration Mode: The pull-up/pull-down value is latched as pcs_lpbk
during reset. See “Strapping Options” section for details.
10 RXC/
SMII_SELECT
Ipd/O MII Receive Clock Output
Operating at:
25 MHz = 100 Mbps
2.5 MHz = 10 Mbps
Configuration Mode: The pull-up/pull-down value is latched as SMII during
reset. See “Strapping Options” section for details.
11 RXER/
RX_ER/
ISO
Ipd/O MII Mode: Receive Error Output /
RMII Mode: Receive Error /
Configuration Mode: The pull-up/pull-down value is latched as ISOLATE
during reset. See “Strapping Options” section for details.
12 GND Gnd Ground
13 VDDC Pwr Digital core 1.8 V only power supply
14 TXER Ipd MII Transmit Error Input
15 TXC/
REFCLK/
CLOCK
I/O MII Mode: MII Transmit Clock Output /
RMII Mode: 50 MHz Reference Clock Input /
SMII Mode: 125 MHz Synchronization Clock Input
16 TXEN Ipd MII Transmit Enable Input
17 TXD0/
TXD[0]/
TX
Ipd MII Mode: Transmit Data Input[0] /
RMII Mode: Transmit Data Input[0] /
SMII Mode: Transmit Data and Control
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
7
Pin Number Pin Name Type (Note 1) Pin Function
18 TXD1/
TXD[1]/
SYNC
Ipd MII Mode: Transmit Data Input[1] /
RMII Mode: Transmit Data Input[1] /
SMII Mode: SYNC
19 TXD2 Ipd MII Transmit Data Input[2]
20 TXD3 Ipd MII Transmit Data Input[3]
21 COL /
RMII_SELECT
Ipd/O MII Collision Detect Output
Configuration Mode: The pull-up/pull-down value is latched as RMII select
during reset. See “Strapping Options” section for details.
22 CRS/
RMII_BTB
Ipd/O MII Carrier Sense Output
Configuration Mode: The pull-up/pull-down value is latched as RMII Loop-
back during reset when RMII mode is selected. See “Strapping Options
section” for details.
23 GND Gnd Ground
24 VDDIO Pwr Digital IO 2.5 / 3.3V tolerance power supply
25 INT#/
PHYAD0
Ipu/O Management Interface (MII) Interrupt Out.
Configuration Mode: Latched as PHYAD[0] during power up / reset. See
“Strapping Options” section for details.
26 Programmable LED Output 0
Configuration Mode: The external pull down enable test mode and only used
for tfactory test. Active Low. The LED0 pin is also programmable via register
1eh.
LED mode = 00
Link/Act Pin State LED Definition
No Link H Off
Link L On
LED0/
TEST
Ipu/O
Activity - Toggle
LED mode = 01
Link Pin State LED Definition
No Link H Off
Link L On
LED mode = 10
10Mbps Link Pin State LED Definition
No Link H Off
Link L On
27 Programmable LED Output 1
Configuration Mode: Latched as SPEED (Register 0, bit 13) during power up
/ reset. See “Strapping Options” Section for details. Active Low. The LED1
pin is also programmable via register 1eh.
LED mode = 00
Speed Pin State LED Definition
10BT H Off
LED1 /
SPD100/
noFEF
Ipu/O
100BT L On
LED mode = 01
Speed Pin State LED Definition
10BT H Off
100BT L On
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
8
Pin Number Pin Name Type (Note 1) Pin Function
LED mode = 10
100Mbps Link Pin State LED Definition
No Link H Off
Link L On
28 Programmable LED Output 2
Configuration Mode: Latched as DUPLEX (register 0h, bit 8) during power up
/ reset. See “Strapping Options” Section for details. Active Low. The LED2
pin is also programmable via register 1eh.
LED mode = 00
Duplex Pin State LED Definition
Half H Off
LED2/
DUPLEX
Ipu/O
Full L On
LED mode = 01
Full Duplex/Col Pin State LED Definition
Half H Off
Full L On
Collision - Toggle
LED mode = 10
Duplex Pin State LED Definition
Half H Off
Full L On
29 Programmable LED Output 3
Configuration Mode: Latched as ANEG_EN (register 0h, bit 12) during power
up / reset. See “Strapping Options” Section for details. Active Low. The
LED3 pin is also programmable via register 1eh.
LED mode = 00
Collision Pin State LED Definition
No Collision H Off
LED3/
NWAYEN
Ipu/O
Collision L On
LED mode = 01
Activity Pin State LED Definition
Activity - Toggle
LED mode = 10
Activity Pin State LED Definition
Activity - Toggle
30 PD# Ipu Power Down.
1=Normal operation, 0=Power down, Active low
31 VDDRX Pwr
Analog 1.8 V power supply
32 RX- I Receive Input
Differential receive input pins for FX, 100BASE-TX or 10BASE-T
33 RX+ I Receive Input
Differential receive input pin for FX, 100BASE-TX or 10BASE-T
34 FXSD/
FXEN
Ipd/O Fiber Mode Enable / Signal Detect in Fiber Mode
If FXEN=0, FX mode is disable. The default is “0”.
See “100BT FX Mode” section for more details.
35 GND Gnd Ground
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
9
Pin Number Pin Name Type (Note 1) Pin Function
36 GND Gnd Ground
37 REXT I
External resistor (6.65K ) connects to REXT and GNDRX
38 VDDRCV Pwr
Analog 3.3 V power supply (See “Circuit design ref for power supply”
section for details)
39 GND Gnd
Ground
40 TX- O Transmit Outputs
Differential transmit output for 100BASE-TX/FX or 10BASE-T
41 TX+ O Transmit Outputs
Differential transmit output for FX, 100BASE-TX/FX or 10BASE-T
42 NC No Connect
43 NC No Connect
44 GND Gnd Ground
45 XO O XTAL feedback
Used with XI for Xtal application.
46 XI I Crystal Oscillator Input
Input for a crystal or an external 25 MHz clock
47 VDDPLL Pwr Analog PLL 1.8 V power supply
48 RST# Ipu Chip Reset
Active low, minimum of 50 us pulse is required
Note 1:
Pwr = power supply;
Gnd = ground;
I = input;
O = output;
I/O = bi-directional
Ipu = input w/ internal pull up;
Ipd = input w/ internal pull down;
Ipu/O = input w/ internal pull up during
reset, output pin otherwise;
Ipd/O = input w/ internal pull down during
reset, output pin otherwise;
PD = strap pull down;
PU = strap pull up;
Note 2:
MII Rx Mode: The RXD[3..0] bits are synchronous with RXCLK. When RXDV is asserted, RXD [3..0]
presents valid data to MAC through the MII. RXD [3..0] is invalid when RXDV is de-asserted.
Note 3:
RMII Rx Mode: The RXD[1..0] bits are synchronous with REF_CLK. For each clock period in which
CRS_DV is asserted, two bits of recovered data are sent from the PHY.
Note 4:
SMII Rx Mode: Receive data and control information are sent in 10 bit segments. In 100MBit mode, each
segment represents a new byte of data. In 10MBit mode, each segment is repeated ten times; therefore,
every ten segments represents a new byte of data. The MAC can sample any one of every 10 segments in
10MBit mode.
Note 5:
MII Tx Mode: The TXD[3..0] bits are synchronous with TXCLK. When TXEN is asserted, TXD [3..0]
presents valid data from the MAC through the MII. TXD [3..0] has no effect when TXEN is de-asserted.
Note 6:
RMII Tx Mode: The TXD[1..0] bits are synchronous with REF_CLK. For each clock period in which TX_EN
is asserted, two bits of recovered data are recovered by the PHY.
Note 7:
SMII Tx Mode: Transmit data and control information are received in 10 bit segments. In 100MBit mode,
each segment represents a new byte of data. In 10MBit mode, each segment is repeated ten times;
therefore, every ten segments represents a new byte of data. The PHY can sample any one of every 10
segments in 10MBit mode.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
10
Strapping Options
Pin Number Pin Name Type (Note 2) Description
6,5,
4,3
PHYAD[4:1] /
RXD[0:3]
Ipd/O
25 PHYAD0/
INT#
Ipu/O
PHY Address latched at power-up / reset. The default PHY
address is 00001.
9 PCS_LPBK/
RXDV
Ipd/O Enables PCS_LPBK mode at power-up / reset.
PD (default) = Disable, PU = Enable
10 SMII_SELECT
/ RXC
Ipd/O Enables SMII mode at power-up / reset.
PD (default) = Disable, PU = Enable
11 ISO / RXER Ipd/O Enables ISOLATE mode at power-up /reset.
PD (default) = Disable, PU = Enable
21 RMII_SELECT
/ COL
Ipd/O Enables RMII mode at power-up / reset.
PD (default) = Disable, PU = Enable
22 RMII_BTB/
CRS
Ipd/O Enable RMII_BTB mode at power-up / reset.
PD (default) = Disable, PU = Enable
27 SPD100 /
No FEF /
LED1
Ipu/O Latched into Register 0h bit 13 during power-up / reset.
PD = 10Mb/s, PU (default) = 100Mb/s.
If SPD100 is asserted during power-up / reset, this pin also
latched as the Speed Support in register 4h. (If FXEN is
pulled up, the latched value 0 means no Far _End _Fault.)
28 DUPLEX/
LED2
Ipu/O Latched into Register 0h bit 8 during power-up / reset.
PD = Half Duplex, PU (default) = Full duplex.
If Duplex is pulled up during reset, this pin also latched as the
Duplex support in register 4h.
29 NWAYEN/
LED3
Ipu/O Nway (auto-=Negotiation) Enable
Latched into Register 0h bit 12 during power-up / reset. PD =
Disable Auto-Negotiation, PU (default) = Enable Auto-
Negotiation
30 PD# Ipu Power Down Enable
PU (default) = Normal operation, PD = Power down mode
Note: Strap-in is latched during power up or reset. In some systems, the MAC RXD pins may drive high at all times causing the
PHY strap-in to be latched high during power up or system reset. In this case, it is recommended to use a strong pull down to GND
via 1kohm resistor on RXDV, RXC, and RXER pins. Otherwise, the PHY may stay in Isolate or loop back modes.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
11
Pin Configuration
1
2
3
4
5
6
7
8
9
10
11
12 KS8001S
XO
GND
NC
RST#
NC
TX-
GND
VDDPLL
XI
TX+
VDDRCV
REXT
MDIO
MDC
RXD3/PHYAD1
RXD2/PHYAD2
RXD0/PHYAD4
VDDIO
RXC
RXER/ISO
RXD1/PHYAD3
GND
RXDV/PCS_LPBK
GND
13
14
15
16
17
18
19
20
21
22
23
24
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
VDDC
TXER
TXC/REF_CLK
TXEN
TXD0
TXD1
TXD2
TXD3
COL/RMII
CRS/RMII_BTB
GND
VDDIO
GND
GND
FXSD/FXEN
RX+
RX-
VDDRX
PD#
LED3/NWAYEN
LED2/DUPLEX
LED1/SPD100
LED0/TEST
INT#/PHYAD0
Top View
SSOP 48
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
10
11
12
36
35
34
33
32
31
30
29
28
27
26
25
KS8001L
48
47
46
45
44
43
42
41
40
39
38
37
RX+
RX-
VDDRX
GND
PD#
LED2/DUPLEX
LED1/SPD100
GND
FXSD/FXEN
LED3/NWAYEN
LED0/TEST
INT#/PHYAD0
VDDC
TXER
TXC/REF_CLK
TXEN
TXD0
TXD1
TXD2
TXD3
COL/RMII
CRS/RMII_BTB
GND
VDDIO
MDIO
MDC
RXD3/PHYAD1
RXD2/PHYAD2
RXD0/PHYAD4
VDDIO
RXC
RXER/ISO
RXD1/PHYAD3
GND
RXDV/PCS_LPBK
GND
RST#
VDDPLL
XI
XO
NC
TX-
GND
VDDRCV
REXT
GND
NC
TX+
Top View
LQFP 48
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
12
Functional Description
100BASE-TX Transmit
The 100BASE-TX transmit function performs parallel-to-serial conversion, NRZ to NRZI conversion, MLT-3 encoding and
transmission. The circuitry starts with a parallel-to-serial conversion, which converts the 25 MHz, 4-bit nibbles into a 125 MHz serial
bit stream. The incoming data is clocked in at the positive edge of the TXC signal. The serialized data is further converted from
NRZ to NRZI format, and then transmitted in MLT3 current output. The output current is set by an external 1% 6.65 K resistor for
the 1:1 transformer ratio. It has typical rise/fall times of 4 ns and complies with the ANSI TP-PMD standard regarding amplitude
balance, overshoot and timing jitter. The wave-shaped 10BASE-T output driver is also incorporated into the 100BASE-TX driver.
100BASE-TX Receive
The 100BASE-TX receive function performs adaptive equalization, DC restoration, MLT-3 to NRZI conversion, data and clock
recovery, NRZI to NRZ conversion, and serial-to-parallel conversion. The receiving side starts with the equalization filter to
compensate for inter-symbol interference (ISI) over the twisted pair cable. Since the amplitude loss and phase distortion are a
function of the length of the cable, the equalizer has to adjust its characteristic to optimize performance. In this design, the variable
equalizer will make an initial estimation based upon comparisons of incoming signal strength against some known cable
characteristics, then tunes itself for optimization. This is an ongoing process and can self adjust against environmental changes
such as temperature variations.
The equalized signal then goes through a DC restoration and data conversion block. The DC restoration circuit is used to
compensate for the effects of base line wander and to improve the dynamic range. The differential data conversion circuit converts
the MLT3 format back to NRZI. The slicing threshold is also adaptive.
The clock recovery circuit extracts the 125 MHz clock from the edges of the NRZI signal. This recovered clock is then used to
convert the NRZI signal into the NRZ format. Finally, the NRZ serial data is converted to 4-bit parallel 4B nibbles. A synchronized
25 MHz RXC is generated so that the 4B nibbles is clocked out at the negative edge of RCK25 and is valid for the receiver at the
positive edge. When no valid data is present, the clock recovery circuit is locked to the 25 MΗz reference clock and both TXC and
RXC clocks continue to run.
PLL Clock Synthesizer
The KS8001 generates 125 MΗz, 25 MΗz and 20 MΗz clocks for system timing. An internal crystal oscillator circuit provides the
reference clock for the synthesizer.
Scrambler/De-scrambler (100BASE-TX only)
The purpose of the scrambler is to spread the power spectrum of the signal in order to reduce EMI and baseline wander.
10BASE-T Transmit
When TXEN (transmit enable) goes high, data encoding and transmission will begin. The KS8001 will continue to encode and
transmit data as long as TXEN remains high. The data transmission will end when TXEN goes low. The last transition occurs at the
boundary of the bit cell if the last bit is zero, or at the center of the bit cell if the last bit is one. The output driver is incorporated into
the 100BASE- driver to allow transmission with the same magnetics. They are internally wave-shaped and pre-emphasized into
outputs with a typical 2.5 V amplitude. The harmonic contents are at least 27 dB below the fundamental when driven by an all-ones
Manchester-encoded signal.
10BASE-T Receive
On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and a PLL
performs the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data. A squelch
circuit rejects signals with levels less than 300 mV or with short pulse widths in order to prevent noises at the RX+ or RX- input from
falsely trigger the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming signal and the KS8001
decodes a data frame. This activates the carrier sense (CRS) ad RXDV signals and makes the receive data (RXD) available. The
receive clock is maintained active during idle periods in between data reception.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
13
SQE and Jabber Function (10BASE-T only)
In 10BASE-T operation, a short pulse will be put out on the COL pin after each packet is transmitted. This is required as a test of the
10BASE-T transmit/receive path and is called SQE test. The 10BASE-T transmitter will be disabled and COL will go high if TXEN is
High for more than 20 ms (Jabbering). If TXEN then goes low for more than 250 ms, the 10BASE-T transmitter will be re-enabled
and COL will go Low.
Auto-Negotiation
The KS8001 performs auto-negotiation by hardware strapping option (pin 29) or software (Register 0.12). It will automatically
choose its mode of operation by advertising its abilities and comparing them with those received from its link partner whenever auto-
negotiation is enabled. It can also be configured to advertise 100BASE-TX or 10BASE-T in either full- or half-duplex mode. Auto-
negotiation is disabled in FX mode.
During auto-negotiation, the contents of Register 4, coded in Fast Link Pulse (FLP), will be sent to its link partner under the
conditions of power-on, link-loss or re-start. At the same time, the KS8001 will monitor incoming data to determine its mode of
operation. Parallel detection circuit will be enabled as soon as either 10BASE-T NLP (Normal Link Pulse) or 100BASE-TX idle is
detected. The operation mode is configured based on the following priority:
Priority 1: 100BASE-TX, full-duplex
Priority 2: 100BASE-TX, half-duplex
Priority 3: 10BASE-T, full-duplex
Priority 4: 10BASE-T, half-duplex
When the KS8001 receives a burst of FLP from its link partner with 3 identical link code words (ignoring acknowledge bit), it will store
these code words in Register 5 and wait for the next 3 identical code words. Once the KS8001 detects the second code words, it
then configures itself according to the above-mentioned priority. In addition, the KS8001 also checks for 100BASE-TX idle or
10BASE-T NLP symbols. If either is detected, the KS8001 automatically configures to match the detected operating speed.
MII Management Interface
The KS8001 supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input / Output (MDIO)
Interface. This interface allows upper-layer devices to monitor and control the state of the KS8001. The MDIO interface consists of
the following:
A physical connection including a data line (MDIO), a clock line (MDC) and an optional interrupt line (INTRPT)
A specific protocol that runs across the above-mentioned physical connection and it also allows one controller to
communicate with multiple KS8001 devices. Each KS8001 is assigned an MII address between 0 and 31 by the PHYAD
inputs.
An internal addressable set of fourteen 16-bit MDIO registers. Register [0:6] are required and their functions are specified
by the IEEE 802.3 specifications. Additional registers are provided for expanded functionality.
The INTPRT pin functions as a management data interrupt in the MII. An active Low or High in this pin indicates a status change on
the KS8001 based upon 1fh.9 level control. Register bits at 1bh[15:8] are the interrupt enable bits. Register bits at 1bh[7:0] are the
interrupt condition bits. This interrupt is cleared by reading Register 1bh.
MII Data Interface
The data interface consists of separate channels for transmitting data from a 10/100 802.3 compliant Media Access Controller (MAC)
to the KS8001, and for receiving data from the line. Normal data transmission is implemented in 4B Nibble Mode (4-bit wide
nibbles).
Transmit Clock (TXC): The transmit clock is normally generated by the KS8001 from an external 25MHz reference source at the
X1 input. The transmit data and control signals must always be synchronized to the TXC by the MAC. The KS8001 normally
samples these signals on the rising edge of the TXC.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
14
Receive Clock (RXC): For 100BASE-TX links, the receive clock is continuously recovered from the line. If the link goes down, and
auto-negotiation is disabled, the receive clock then operates off the master input clock (X1 or TXC). For 10BASE-T links, the receive
clock is recovered from the line while carrier is active, and operates from the master input clock when the line is idle. The KS8001
synchronizes the receive data and control signals on the falling edge of RXC in order to stabilize the signals at the rising edge of the
clock with 10ns setup and hold times.
Transmit Enable: The MAC must assert TXEN at the same time as the first nibble of the preamble, and de-assert TXEN after the
last bit of the packet.
Receive Data Valid: The KS8001 asserts RXDV when it receives a valid packet. Line operating speed and MII mode will determine
timing changes in the following way:
For 100BASE-TX link with the MII in 4B mode, RXDV is asserted from the first nibble of the preamble to the last nibble of
the data packet.
For 10BASE-T links, the entire preamble is truncated. RXDV is asserted with the first nibble of the SFD “ 5D” and remains
asserted until the end of the packet.
Error Signals: Whenever the KS8001 receives an error symbol from the network, it asserts RXER and drives “1110” (4B) on the
RXD pins. When the MAC asserts TXER, the KS8001 will drive “H” symbols (a Transmit Error define in the IEEE 802.3 4B/5B code
group) out on the line to force signaling errors.
Carrier Sense (CRS): For 100TX links, a start-of-stream delimiter, or /J/K symbol pair causes assertion of Carrier Sense (CRS).
An end-of-stream delimiter,or /T/R symbol pair causes de-assertion of CRS. The PMA layer will also de-assert CRS if IDLE symbols
are received without /T/R, yet in this case RXER will be asserted for one clock cycle when CRS is de-asserted. For 10T links, CRS
assertion is based on reception of valid preamble, and de-assertion on reception of an end-of-frame (EOF) marker.
Collision: Whenever the line state is half-duplex and the transmitter and receiver are active at the same time, then the KS8001
asserts its collision signal, which is asynchronous to any clock.
RMII (Reduced MII) Data Interface
RMII interface specifies a low pin count (Reduced) Media Independent Interface (RMII) intended for use between Ethernet PHYs and
Switch or Repeater ASICs. It is fully compliant with IEEE 802.3u [2].
This interface has the following characteristics:
It is capable of supporting 10Mb/s and 100Mb/s data rates
A single clock reference is sourced from the MAC to PHY (or from an external source)
It provides independent 2 bit wide (di-bit) transmit and receive data paths
It uses TTL signal levels, compatible with common digital CMOS ASIC processes
RMII Signal Definition
Signal Name
Direction
(with respect to
the PHY)
Direction
(with respect to
the MAC)
Use
REF_CLK Input Input or Output Synchronous clock reference for receive, transmit and control
interface
CRS_DV Output Input Carrier Sense/Receive Data Valid
RXD[1:0] Output Input Receive Data
TX_EN Input Output Transit Enable
TXD[1:0] Input Output Transit Data
RX_ER Output Input
(Not Required) Receive Error
Note: Unused MII signals, TXD[3:2], TXER need to be tied to GND when RMII is used
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
15
Reference Clock (REF_CLK)
REF_CLK is a continuous 50 MHz clock that provides the timing reference for CRS_DV, RXD[1:0], TX_EN, TXD[1:0], and RX_ER.
REF_CLK is sourced by the MAC or an external source. Switch implementations may choose to provide REF_CLK as an input or an
output depending on whether they provide a REF_CLK output or rely on an external clock distribution device. Each PHY device shall
have an input corresponding to this clock but may use a single clock input for multiple PHYs implemented on a single IC.
Carrier Sense/Receive Data Valid (CRS_DV)
CRS_DV is asserted asynchronously on detection of carrier due to the criteria relevant to the operating mode. That is, in 10BASE-T
mode, when squelch is passed or in 100BASE-X mode when 2 non-contiguous zeroes in 10 bits are detected carrier is said to be
detected.
Loss of carrier shall result in the de-assertion of CRS_DV synchronous to REF_CLK. So long as carrier criteria are being met,
CRS_DV shall remain asserted continuously from the first recovered di-bit of the frame through the final recovered di-bit and shall be
negated prior to the first REF_CLK that follows the final di-bit.
The data on RXD[1:0] is considered valid once CRS_DV is asserted. However, since the assertion of CRS_DV is asynchronous
relative to REF_CLK, the data on RXD[1:0] shall be "00" until proper receive signal decoding takes place (see definition of RXD[1:0]
behavior).
Receive Data [1:0] (RXD[1:0])
RXD[1:0] shall transition synchronously to REF_CLK. For each clock period in which CRS_DV is asserted, RXD[1:0] transfers two
bits of recovered data from the PHY. In some cases (e.g. before data recovery or during error conditions) a pre-determined value for
RXD[1:0] is transferred instead of recovered data. RXD[1:0] shall be "00" to indicate idle when CRS_DV is de-asserted. Values of
RXD[1:0] other than "00" when CRS_DV is de-asserted are reserved for out-of-band signaling (to be defined). Values other than "00"
on RXD[1:0] while CRS_DV is de-asserted shall be ignored by the MAC/repeater. Upon assertion of CRS_DV, the PHY shall ensure
that RXD[1:0]=00 until proper receive decoding takes place.
Transmit Enable (TX_EN)
Transmit Enable TX_EN indicates that the MAC is presenting di-bits on TXD[1:0] on the RMII for trans-mission. TX_EN shall be
asserted synchronously with the first nibble of the preamble and shall remain asserted while all di-bits to be transmitted are
presented to the RMII. TX_EN shall be negated prior to the first REF_CLK following the final di-bit of a frame. TX_EN shall transition
synchronously with respect to REF_CLK.
Transmit Data [1:0] (TXD[1:0])
Transmit Data TXD[1:0] shall transition synchronously with respect to REF_CLK. When TX_EN is asserted, TXD[1:0] are accepted
for transmission by the PHY. TXD[1:0] shall be "00" to indicate idle when TX_EN is de-asserted. Values of TXD[1:0] other than "00"
when TX_EN is de-asserted are reserved for out-of-band signaling (to be defined). Values other than "00" on TXD[1:0] while TX_EN
is disserted shall be ignored by the PHY.
Collision Detection
Since the definition of CRS_DV and TX_EN both contain an accurate indication of the start of frame, the MAC can reliably
regenerate the COL signal of the MII by Ending TX_EN and CRS_DV.
During the IPG time following the successful transmission of a frame, the COL signal is asserted by some transceivers as a self-test.
The Signal Quality Error (SQE) function will not be supported by the reduced MII due to the lack of the COL signal. Historically, SQE
was present to indicate that a transceiver located physically remote from the MAC was functioning. Since the reduced MII only
supports chip-to-chip connections on a PCB, SQE functionality is not required.
RX_ER
The PHY shall provide RX_ER as an output according to the rules specified in IEEE 802.3u [2] (see Clause 24, Figure 24-11 -
Receive State Diagram). RX_ER shall be asserted for one or more REF_CLK periods to indicate that an error (e.g. a coding error or
any error that a PHY is capable of detecting, and that may otherwise be undetectable by the MAC sublayer) was detected
somewhere in the frame presently being transferred from the PHY. RX_ER shall transition synchronously with respect to REF_CLK.
While CRS_DV is de-asserted, RX_ER shall have no effect on the MAC.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
16
RMII AC Characteristics
RMII Transmit Timing
REF_CLK
20ns
TXD[1:0]
TXEN
TXER
t1
t2
Parameter Min Typ Max Units
REF_CLK Frequency 50 MHz
TXEN, TXD[1:0], TX_EN, Data Setup to REF_CLK
rising edge 4 ns
TXEN, TXD[1:0], TX_EN, Data hold from REF_CLK
rising edge 2 ns
RMII Receive Timing
REF_CLK
20ns
tod
RXD[1:0]
RXDV
RXER
Parameter Min Typ Max Units
REF_CLK Frequency 50 MHz
RXD[1:0], CRS_DV, RX_ER Output delay from
REF_CLK rising edge 2.8 10 ns
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
17
SMII Signal Definition
SMII is composed of two signals per port, a global synchronization signal, and a global 125MHz reference clock. All signals are
synchronous to the clock. All SMII I/F uses a common 125MHz reference clock and SYNC signals that are synchronous to the
reference clock. There are two signals in SMII from MAC-to-PHY for each port (TXD and TxSYNC), and one signal per port from
PHY-to-MAC (RXD).
The Serial Media Independent Interface (SMII) is designed to satisfy the following requirements:
Convey complete MII information between a 10/100 PHY and MAC with two pins per port.
Allow a multi-port MAC/PHY communication with one system clock.
Operate in both half and full duplex.
Per packet switching between 10Mbit and 100Mbit data rates.
Allow direct MAC to MAC communication.
SMII Signals
Signal Name From To Use
RX PHY MAC Receive Data and Control
TX MAC PHY Transmit Data and Control
SYNC MAC PHY Synchronization
Clock System MAC&PHY Synchronization
Receive Path
Receive data and control information are signaled in ten bit segments. In 100Mbit mode, each segment represents a new byte of
data. In 10Mbit mode, each segment is repeated ten times; therefore, every ten segments represent a new byte of data. The MAC
can simply any one of every 10 segment ion 10Mbit mode.
Segment boundaries are delimited by SYNC. The MAC continuously generates a pulse on SYNC every 10 clocks.
Receive Sequence Diagram
CRS RX_DV RXD0 RXD1 RXD2 RXD3 RXD4 RXD5 RXD6 RXD7
RX_CLK
RX_SYNC
RX
RX contains all of the information found on the receive path of the standard MII.
Bits Purpose
CRS Carrier Sense – identical to MII, except that it is not an asynchronous signal
RX_DV Receive Data Valid – identical to MII
RXD7-0 Encoded Data, see the RXD0-7 Encoding table
RX – Bit Description
RXD7-0 are used to convey packet data, RX_ER, and PHY status. The MAC can infer the meaning of RXD on a segment-by-basis
by encoding the two control bits.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
18
CRS RX_DV RXD0 RXD1 RXD2 RXD3 RXD4 RXD5 RXD6 RXD7
X 0 RX_ER
from
previous
frame
Speed
0=10Mbit
1=100Mbit
Duplex
0=Half
1=Full
Link
0=Down
1=Up
Jabber
0=OK
1=Error
Upper
Nibble
0=invalid
1=valid
False
Carrier
Detected
1
X 1 One Data Byte (Two MII Data Nibble)
TXD7 – 0 Encoding
Inter-frame status bit RXD5 conveys the validity of the upper nibble of the byte of the previous frame. Inter-frame status bit RXD0
indicates whether or not the PHY detected an error somewhere on the previous frame. Both of these bits should be valid in the
segment immediately following a frame, and should stay valid until the first data segment of the next frame begins.
When asserted, inter-frame status bit RXD6 indicates that the PHY has detected a false carrier event.
In order to send receive data to the MAC synchronous to the reference clock, the PHY must pass the data through an elasticity FIFO
to handle any difference between the reference clock rate and the clock at the packet source. The Ethernet specification calls for
packet data to be referenced to a clock with a frequency tolerance of 100ppm (0.01%); however, it is not uncommon to encounter
Ethernet stations with clocks that have frequency errors up to 0.1%. Therefore, the elasticity FIFO should be at least 27 bits * long,
filling to the half-way point before beginning valid data transfer via RX. RX_ER should be asserted if, during the reception of a frame,
this fifo overflows or underflows.
Only RXD and RX_DV should be passed through the elasticity FIFO. CRS should not be passed through the elasticity FIFO. Instead,
CRS should be asserted for the time the ‘wire’ is busy receiving a frame.
Transmit Path
Transmit data and control information are signaled in ten bit segments, just like the receive path. In 100Mbit mode, each segment
represents anew byte of data. In 10Mbit mode each segment is repeated ten times; therefore, every ten segments represents a new
byte of data. The PHY can sample any one of every 10 segments in 10Mbit mode.
Segment boundaries are delimited by SYNC. The MAC continuously generates a pulse on SYNC every 10 clocks.
Transmit Sequence Diagram
TX_ER TX_EN TXD0 TXD1 TXD2 TXD3 TXD4 TXD5 TXD6 TXD7
TX _ C LK
TX _ S Y N C
TX
Bits Purpose
TX_EN Transmit Enable – identical to MII
TX_ER Transmit Error – identical to MII
TXD7-0 Encoded Data – see TXD7-0 Encoding Table
TX- Bit Description
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
19
As far as the PHY is concerned, TXD7-0 are used to convey only packet data. To allow for a direct MAC to MAC connection, the
MAC uses TXD7-0 to signal ‘status’ in between frames.
TX_ER TX_EN TXD0 TXD1 TXD2 TXD3 TXD4 TXD7-5
x 0 Use to force
an error in a
direct MAC to
MAC
connection
1
100MBit
1
Full Duplex
1
Link Up
0
No Jabber
1
x 1 One Data Byte (Two MII Data Nibbles)
TXD7 – 0 Encoding
Collision Detection
Collisions occur when CRS and TX_EN are simultaneously asserted. For this to work, the PHY must ensure that CRS is not affected
by its transmit path.
DC Specification
Parameter Symbol Min Max Units
Input High Voltage Vih 2.0 Volts
Input Low Voltage Vil 0.8 Volts
Input High Current Iih -10 10 uA
Input Low Current Iil -10 10 uA
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
20
Timing Specification
Parameter Min Max Units
Input Setup 1.5 ns
Input Hold 1 ns
Output Delay 1.5 5 ns
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
21
HP Auto Crossover (Auto MDI/MDI-X)
Automatic MDI/MDI-X configuration is intended to eliminate the need for crossover cables between similar devices. The assignment
of pin-outs for a 10/100 BASE-T crossover function cable is shown below.
This feature can eliminate the confusion in real applications by allowing both straight cable and crossover cables. This feature is
controlled by register 1f:13, see “Register 1fh” section for details.
R e c e iv e P a irTransm it Pair
R e c e iv e P a ir
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
Transm it Pair
Straight Through Cable
10/100 Base-T
M edia Dependent Interface
10/100 Base-T
M edia Dependent Interface
M odular Connector
(RJ45)
NIC
M odular Connector
(RJ45)
HUB
(Repeater or Switch)
R ec e iv e P a ir R e c e iv e P a ir
T ra n sm it P a ir
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
T ra n sm it P a ir
Crossover Cable
10/100 BASE-T
Media Dependent Interface
10/100 Base-T
Media Dependent Interface
Modular Connector (RJ45)
HUB
(Repeater or Switch)
Modular Connector (RJ45)
HUB
(R epeater or S witch)
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
22
Auto MDI/MDI-X Cross-Over Transformer Connection
KS8001 features HP Auto MDI/MDI-X crossover and requires symmetric transformers that support Auto MDI/MDI-X. See Selection
of Isolation Transformers on p. 43 for a list of transformers that support Auto MDI/MDI-X.
Power Management
The KS8001 offers the following modes for power management:
Power Down Mode: This mode can be achieved by writing to Register 0.11 or pulling pin 30 PD# Low. In the power down
state, the KS8061 disables all internal functions and drives output pins to logic zero, except for the MII serial management
interface.
Power Saving Mode: writing to register 1fh.10 can disable this mode. The KS8001 will then turn off everything except for
the Energy Detect and PLL circuits when the cable is not installed. In other words, the KS8001 will shutdown most of the
internal circuits to save power if there is no link. Power Saving mode will be in this most effective state when Auto-
Negotiation Mode is enabled.
100BT FX Mode
100BT FX mode is activated when FXSD/FXEN is higher than 0.6V (This pin has a default pull down). Under this mode, the auto-
negotiation and auto-MDIX features are disabled.
In fiber operation FXSD pin should connect to the SD (signal detect) output of the fiber module. The internal threshold of FXSD is
around Vdd +/- 50 mV (2.2V +/- 0.05V at 3.3V). Above this level, it is considered Fiber signal detected, and the operation is
summarized in the following table:
FXSD/FXEN Condition
Less than 0.6V 100TX mode
Less than 2.15V,
but greater than 0.6V
FX mode
No signal detected
FEF generated
Greater than 2.25V FX mode
Signal detected
To ensure proper operation, the swing of fiber module SD should cover the threshold variation. A resistive voltage divider is
recommended to adjust the SD voltage range.
FEF (Far End Fault), repetition of a special pattern, which consists of 84-ones and 1-zero, is generated under “FX mode with no
signal detected”. The purpose of FEF is to notify the sender of a faulty link. When receiving a FEF, the LINK will go down to indicate
a fault, even with fiber signal detected. The transmitter is not affected by receiving a FEF and still sends out its normal transmit
pattern from MAC. FEF can be disabled by strapping pin27 low, please refer to “Strapping Options” section.
Media converter operation
The KS8001 is capable of performing media conversion with 2 parts in a back-to-back RMII mode as indicated in the diagram. Both
parts are in RMII mode and with RMII_BTB asserted (pin21 & 22 strapped high). One part is operating at TX mode and the other in
FX mode. Both parts can share a common 50MHz oscillator.
Under this operation, auto-Negotiation on the TX side will prohibit 10BASE-T link up. Additional options can be implemented under
this operation. Disable the transmitter and set it at tri-state by controlling the high TXD2 pin. In order to do this, RXD2 and TXD2 pins
need to be connected via an inverter. When TXD2 pin is high in both the copper and fiber operation, it disables transmit. Meanwhile,
the RXD2 pin on the copper side serves as the energy detect and can indicate if a line signal is detected. TXD3 should be tied low
and RXD3 let float. Please contact your local Micrel FAE for a Media Converter reference design.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
23
KS8001
Rx +/-
Tx +/-
FTx
FRx
KS8001
Vcc
Pin
34
RxD
TxD
To the SD pin of the
Fiber Module
(Fiber Mode)
Vcc
RxD
TxD
21 22
Pin
Pin
21 22
OSC
50 MHz
TxC/
Ref_CLK
TxC/
Ref_CLK
LinkMD Cable Diagnostics
The KS8001 utilizes time domain reflectometry (TDR) to analyze the cabling plant for common cabling problems such as open
circuits, short circuits and impedance mismatches. LinkMD works by sending a pulse of known amplitude and duration down the
MDI and MDIX pairs and analyzing the shape of the reflected signal. Timing the duration gives an indication of the distance to the
cabling fault with maximum distance of 200 m and accuracy of +/- 2 m. Cable diagnostics are only valid for copper connections and
do not support fiber optic operation.
LinkMD is used by accessing register 1dh, the LinkMD Control/Status register in conjunction with register 1fh, the 100BASE-TX PHY
Controller register. To use LinkMD, HP Auto-MDIX is disabled by writing a ‘1’ to 1f:13 to enable manual control over which pair is
used to transmit the LinkMD pulse. The self-clearing Cable diagnostic test enable bit, 1d.15 is set to ‘1’ to start the test on this pair.
When 1d.15 returns to ‘0’, the test is complete. The test result is returned in 1d.14:13 and the distance is returned in 1d.8:0. The
cable diagnostic test results are as follows:
00 = Valid test, normal condition
01 = Valid test, open circuit in cable
10 = Valid test, short circuit in cable
11 = Invalid test, LinkMD failed
The ‘11’ case, Invalid test, occurs when it is not possible for the KS8001 to shut down the link partner. In this case, the test is not
run, since it would not be possible for the KS8001 to determine if the detected signal is a reflection of the signal generated or a
signal from another source.
Cable length can be determined by multiplying the contents of 1d.8:0 by 0.39. This constant may be calibrated for different cabling
conditions, including cables with a velocity of propagation that varies significantly from the norm.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
24
Reference Clock Connection Options
KS8001 is capable of performing three different kinds of clock speed options for connecting the external reference clock depends
upon the different interface of using MII/RMII/SMII. The figures below illustrate the recommended connection for using the different
interface options. Please see the selection of reference crystal table for specifications.
XI
XO
25MHz Osc
100ppm
NC
NC
25MHz Oscillator Reference Clock Connection Diagram
XI
XO
22pF
22pF
22pF
22pF
25MHz Xtal
100ppm
25MHz Crystal Reference Clock Connection Diagram
50/125MHz Osc
100ppm
NC
NC
10K XI
XO
REF_CLK
VCC
50/125MHz Oscillator Reference Clock Connection for RMII/SMII Mode Diagram
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
25
Register Map
Register No. Description
0h Basic Control Register
1h Basic Status Register
2h PHY Identifier I
3h PHY Identifier II
4h Auto-Negotiation Advertisement Register
5h Auto-Negotiation Link Partner Ability Register
6h Auto-Negotiation Expansion Register
7h Auto-Negotiation Next Page Register
8h Link Partner Next Page Ability
9h-14h Reserved
15h RXER Counter Register
16h – 1ah Reserved
1bh Interrupt Control/Status Register
1ch Reserved
1dh LinkMD Control/Status Register
1eh PHY Control Register
1fh 100BASE-TX PHY Control Register
Address Name Description Mode Default
Register 0h – Basic Control
0.15 Reset 1 = software reset. Bit is self-clearing RW/
SC
0
0.14 Loop-back 1 = loop-back mode
0 = normal operation
RW 0
0.13 Speed Select
(LSB)
1 = 100Mb/s
0 = 10Mb/s
Ignored if Auto-Negotiation is enabled
(0.12 = 1)
RW Set by SPD100
0.12 Auto-
Negotiation
Enable
1 = enable auto-negotiation process (override
0.13 and 0.8)
0 = disable auto-negotiation process
RW Set by NWAYEN
0.11 Power Down 1 = power down mode
0 = normal operation
RW 0
0.10 Isolate 1 = electrical isolation of PHY from MII and
TX+/TX-
0 = normal operation
RW Set by ISO
0.9 Restart Auto-
Negotiation
1 = restart auto-negotiation process
0 = normal operation. Bit is self-clearing
RW/
SC
0
0.8 Duplex Mode 1 = full duplex
0 = half duplex
RW Set by DUPLEX
0.7 Collision Test 1 = enable COL test
0 = disable COL test
RW 0
0.6:1 Reserved RO 0
0.0 Disable
Transmitter
0 = enable transmitter
1 = disable transmitter
R/W 0
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
26
Address Name Description Mode Default
Register 1h – Basic Status
1.15 100BASE-T4 1 = T4 capable
0 = not T4 capable
RO 0
1.14 100BASE-TX
Full Duplex
1 = capable of 100BASE-X full duplex
0 = not capable of 100BASE-X full duplex
RO 1
1.13 100BASE-TX
Half Duplex
1 = capable of 100BASE-X half duplex
0 = not capable of 100BASE-X half duplex
RO 1
1.12 10BASE-T Full
Duplex
1 = 10Mbps with full duplex
0 = no 10Mbps with full duplex capability
RO 1
1.11 10BASE-T Half
Duplex
1 = 10Mbps with half duplex
0 = no 10Mbps with half duplex capability
RO 1
1.10:7 Reserved RO 0
1.6 No Preamble 1 = preamble suppression
0 = normal preamble
RO 1
1.5 Auto-
Negotiation
Complete
1 = auto-negotiation process completed
0 = auto-negotiation process not completed
RO 0
1.4 Remote Fault 1 = remote fault
0 = no remote fault
RO/LH 0
1.3 Auto-
Negotiation
Ability
1 = capable to perform auto-negotiation
0 = unable to perform auto-negotiation
RO 1
1.2 Link Status 1 = link is up
0 = link is down
RO/LL 0
1.1 Jabber Detect 1 = jabber detected
0 = jabber not detected. Default is Low
RO/LH 0
1.0 Extended
Capability
1 = supports extended capabilities registers RO 1
Register 2h – PHY Identifier 1
2.15:0 PHY ID
Number
Assigned to the 3rd through 18th bits of the
Organizationally Unique Identifier (OUI).
Kendin Communication’s OUI is 0010A1 (hex)
RO 0022h
Register 3h – PHY Identifier 2
3.15:10 PHY ID
Number
Assigned to the 19th through 24th bits of the
Organizationally Unique Identifier (OUI).
Kendin Communication’s OUI is 0010A1 (hex)
RO 000101
3.9:4 Model Number Six bit manufacturer’s model number RO 100001
3.3:0 Revision
Number
Four bit manufacturer’s model number RO 1010
Register 4h – Auto-Negotiation Advertisement
4.15 Next Page 1 = next page capable
0 = no next page capability.
RW 0
4.14 Reserved RO 0
4.13 Remote Fault 1 = remote fault supported
0 = no remote fault
RW 0
4.12 : 11 Reserved RO 0
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
27
Address Name Description Mode Default
4.10 Pause 1 = pause function supported
0 = no pause function
RW 0
4.9 100BASE-T4 1 = T4 capable
0 = no T4 capability
RO 0
4.8 100BASE-TX
Full Duplex
1 = TX with full duplex
0 = no TX full duplex capability
RW Set by SPD100 & DUPLEX
4.7 100BASE-TX 1 = TX capable
0 = no TX capability
RW Set by SPD100
4.6 10BASE-T Full
Duplex
1 = 10Mbps with full duplex
0 = no 10Mbps full duplex capability
RW Set by
DUPLEX
4.5 10BASE-T 1 = 10Mbps capable
0 = no 10Mbps capability
RW 1
4.4:0 Selector Field [00001] = IEEE 802.3 RW 00001
Register 5h – Auto-Negotiation Link Partner Ability
5.15 Next Page 1 = next page capable
0 = no next page capability
RO 0
5.14 Acknowledge 1 = link code word received from partner
0 = link code word not yet received
RO 0
5.13 Remote Fault 1 = remote fault detected
0 = no remote fault
RO 0
5.12 Reserved RO 0
5.11:10 Pause 5.10 5 .11
0
No PAUSE
1
Asymmetric PAUSE (link partner)
0
Symmetric PAUSE
1
Symmetric & Asymmetric PAUSE (local
device)
RO 0
5.9 100 BASE-T4 1 = T4 capable
0 = no T4 capability
RO 0
5.8 100BASE-TX
Full Duplex
1 = TX with full duplex
0 = no TX full duplex capability
RO 0
5.7 100BASE-TX 1 = TX capable
0 = no TX capability
RO 0
5.6 10BASE-T Full
Duplex
1 = 10Mbps with full duplex
0 = no 10Mbps full duplex capability
RO 0
5.5 10BASE-T 1 = 10Mbps capable
0 = no 10Mbps capability
RO 0
5.4:0 Selector Field [00001] = IEEE 802.3 RO 00001
Register 6h – Auto-Negotiation Expansion
6.15:5 Reserved RO 0
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
28
Address Name Description Mode Default
6.4 Parallel
Detection Fault
1 = fault detected by parallel detection
0 = no fault detected by parallel detection.
RO/
LH
0
6.3 Link Partner
Next Page
Able
1 = link partner has next page capability
0 = link partner does not have next page
capability
RO 0
6.2 Next Page
Able
1 = local device has next page capability
0 = local device does not have next page
capability
RO 1
6.1 Page Received 1 = new page received
0 = new page not yet received
RO/
LH
0
6.0 Link Partner
Auto-
Negotiation
Able
1 = link partner has auto-negotiation capability
0 = link partner does not have auto-negotiation
capability
RO 0
Register 7h – Auto-Negotiation Next Page
7.15 Next Page 1 = additional next page(s) will follow
0 = last page
RW 0
7.14 Reserved RO 0
7.13 Message Page 1 = message page
0 = unformatted page
RW 1
7.12 Acknowledge2 1 = will comply with message
0 = cannot comply with message
RW 0
7.11 Toggle 1 = previous value of the transmitted link code
word equaled logic One
0 = logic Zero
RO 0
7.10:0 Message Field 11-bit wide field to encode 2048 messages RW 001
Register 8h – Link Partner Next Page Ability
8.15 Next Page 1 = additional Next Page(s) will follow
0 = last page
RO 0
8.14 Acknowledge 1 = successful receipt of link word
0 = no successful receipt of link word
RO 0
8.13 Message Page 1 = Message Page
0 = Unformatted Page
RO 0
8.12 Acknowledge2 1 = able to act on the information
0 = not able to act on the information
RO 0
8.11 Toggle 1 = previous value of transmitted Link Code
Word equal
to logic zero
0 = previous value of transmitted Link Code
Word equal to logic one
RO 0
8.10:0 Message Field RO 0
Register 15h – RXER Counter
15.15:0 RXER Counter
RX Error counter for the RX_ER in each
package
RO 0000
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
29
Address Name Description Mode Default
Register 1bh – Interrupt Control/Status Register
1b.15 Jabber
Interrupt
Enable
1=Enable Jabber Interrupt
0=Disable Jabber Interrupt
RW 0
1b.14 Receive Error
Interrupt
Enable
1=Enable Receive Error Interrupt
0=Disable Receive Error Interrupt
RW 0
1b.13 Page Received
Interrupt
Enable
1=Enable Page Received Interrupt
0=Disable Page Received Interrupt
RW 0
1b.12 Parallel Detect
Fault Interrupt
Enable
1= Enable Parallel Detect Fault Interrupt
0= Disable Parallel Detect Fault Interrupt
RW 0
1b.11 Link Partner
Acknowledge
Interrupt
Enable
1= Enable Link Partner Acknowledge Interrupt
0= Disable Link Partner Acknowledge Interrupt
RW 0
1b.10 Link Down
Interrupt
Enable
1= Enable Link Down Interrupt
0= Disable Link Down Interrupt
RW 0
1b.9 Remote Fault
Interrupt
Enable
1= Enable Remote Fault Interrupt
0= Disable Remote Fault Interrupt
RW 0
1b.8 Link Up
Interrupt
Enable
1= Enable Link Up Interrupt
0= Disable Link Up Interrupt
RW 0
1b.7 Jabber
Interrupt
1= Jabber Interrupt Occurred
0= Jabber Interrupt Does Not Occurred
RO/SC 0
1b.6 Receive Error
Interrupt
1= Receive Error Occurred
0= Receive Error Does Not Occurred
RO/SC 0
1b.5 Page Receive
Interrupt
1= Page Receive Occurred
0= Page Receive Does Not Occurred
RO/SC 0
1b.4 Parallel Detect
Fault Interrupt
1= Parallel Detect Fault Occurred
0= Parallel Detect Fault Does Not Occurred
RO/SC 0
1b.3 Link Partner
Acknowledge
Interrupt
1= Link Partner Acknowledge Occurred
0= Link Partner Acknowledge Does Not
Occurred
RO/SC 0
1b.2 Link Down
Interrupt
1= Link Down Occurred
0= Link Down Does Not Occurred
RO/SC 0
1b.1 Remote Fault
Interrupt
1= Remote Fault Occurred
0= Remote Fault Does Not Occurred
RO/SC 0
1b.0 Link Up
Interrupt
1= Link Up Interrupt Occurred
0= Link Up Interrupt Does Not Occurred
RO/SC 0
Register 1dh – LinkMD Control/Status Register
1d.15 Cable
diagnostic test
enable
0 = Indicates cable diagnostic test has
completed and the status information is valid
for read.
1 = the cable diagnostic test is activated. This
bit is self-clearing.
RW
SC
0
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
30
Address Name Description Mode Default
1d.14:13 Cable
diagnostic test
result
[00] = normal condition
[01] = open condition has been detected in
cable
[10] = short condition has been detected in
cable
[11] = cable diagnostic test failed
RO 0
1d.12:9 Reserved
1d.8:0 Cable fault
counter
Distance to fault, approximately
0.39m*cabfaultcnt value
RO 0
Register 1eh – PHY Control
1e:15:14 LED mode [00] =
LED3 <- collision
LED2 <- full duplex
LED1 <- speed
LED0 <- link/activity
[01] =
LED3 <- activity
LED2 <- full duplex/collision
LED1 <- speed
LED0 <- link
[10] =
LED3 <- activity
LED2 <- full duplex
LED1 <- 100Mbps link
LED0 <- 10Mbps link
[11] = reserved
RW 0
1e.13 Polarity 0 = Polarity is not reversed
1 = Polarity is reversed
RO
1e.12 Far end fault
detect
0 = Far end fault detected
1 = Far end fault not detected
RO
1e.11 MDIX/MDI
state
0 = MDIX
1 = MDI
RO
1e:10:8 Reserved
1e:7 Remote
loopback
0: normal mode
1: remote (analog) loop back is enable
RW 0
1e:6:0 Reserved
Register 1fh – 100BASE-TX PHY Controller
1f:15 Reserved
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
31
Address Name Description Mode Default
1f:14 Mdi/mdix
select when
auto mdi/mdix
is disable
0 = transmit on pair A (TPFINn/TPFIPn) and
receive on pair B (TPFONn/TPFOPn).
1 = transmit on pair B (TPFONn/TPFOPn) and
receive on pair A (TPFINn/TPFIPn).
R/W
1f:13 Pairswap
disable
1 = disable MDI/MDIX
0 = enable MDI/MDIX
R/W 0
1f.12 Energy detect
1 = presence of signal on RX+/- analog wire
pair
0 = no signal detected on RX+/-
RO 0
1f.11 Force link 1 = force link pass
0 = normal link operation
This bit bypasses the control logic and allow
transmitter to send pattern even if there is no
link.
R/W 0
1f.10 Power Saving 1 = enable power saving
0 = disable
RW 1
1f.9 Interrupt Level 1 = interrupt pin active high
0 = active low
RW 0
1f.8 Enable Jabber 1 = enable jabber counter
0 = disable
RW 1
1f.7 Auto-
Negotiation
Complete
1 = auto-negotiation complete
0 = not complete
RW 0
1f.6 Enable Pause
(Flow-Control
Result)
1 = flow control capable
0 = no flow control
RO 0
1f.5 PHY Isolate 1 = PHY in isolate mode
0 = not isolated
RO 0
1f.4:2 Operation
Mode
Indication
[000] = still in auto-negotiation
[001] = 10BASE-T half duplex
[010] = 100BASE-TX half duplex
[011] = default
[101] = 10BASE-T full duplex
[110] = 100BASE-TX full duplex
[111] = PHY/MII isolate
RO 0
1f.1 Enable SQE
test
1 = enable SQE test
0 = disable
RW 0
1f.0 Disable Data
Scrambling
1 = disable scrambler
0 = enable
RW 0
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
32
Absolute Maximum Rating (Note 1)
Storage Temperature (TS) ……………… -55°C to
+150°C
Supply Referenced to GND…… ………-0.5V to +4.0
All pins …………………………………....-0.5V to +4.0
Important: Please read the Notes at the bottom of the
page.
Operating Range (Note 2)
Supply Voltage
(VDD_PLL, VDD_TX, VDD_RXC, VDDC)…………1.8V ± 5%
(VDD_RCV, VDDIO)……………………………3.3V ± 5%
Ambient Temperature Commercial (TA)...…0°C to
+70°C
Ambient Temperature Industrial (TA)….…-40°C to
+85°C
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
33
Package Thermal Resistance (θJA)(Note 3)
Thermal Resistance θJA θJA θJA θJC
Airflow Velocity (m/s) 0 1 2 0
LQFP 83.56 77.08 72.36 46.93
SSOP 75.19 68.20 66.20 TBD
Electrical Characteristics (Note4)
VDD=3.3V ±10%
Symbol Parameter Condition Min Typ Max Units
Total Supply Current (including TX output drive current) (Note 5)
IDD1 Normal 100BASE-TX Including 40mA output current mA
IDD2 Normal 10BASE-T Including 90mA output current,
indepdendent of utilization
mA
IDD3 Power Saving Mode 1 Auto-negotiation is Enabled
mA
IDD4 Power Down Mode
(software power down)
mA
IDD5 Power down pin (PD#)
TTL Inputs
VIH Input High Voltage ½ VDD (I/O)
+ 0.2 V
VIL Input Low Voltage 0.8 V
IIN Input Current VIN = GND – VDD -10 10 µA
TTL Outputs
VOH Output High Voltage IOH = -4mA ½ VDD (I/O)
+ 0.6 V
VOL Output Low Voltage 0.4 V
I IOZ I Output Tri-State Leakage 10 µA
100BASE-TX Transmit (measured differentially after 1:1 transformer)
VO Peak Differential Ouput
Voltage 50 from each output to VDD 0.95 1.05 V
VIMB Output Voltage Imbalance 50 from each output to VDD 2 %
tr, tt Rise/Fall Time
Rise/Fall Time Imbalance 3
0 5
0.5
ns
ns
Duty Cycle Distortion ±0.5 ns
Overshoot %
VSET Refernce Voltage of ISET 0.75 V
Propagation Delay 45 60 ns
Jitter 0.7 1.4 ns(pk-pk)
10BASE-T Transmit (measured differentially after 1:1 transformer)
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
34
VP Peak Differential Ouput
Voltage 50 from each output to VDD 2.2 2.8 V
VIMB Output Voltage Imbalance 50 from each output to VDD
±3.5 ns
tr, tt Rise/Fall Time 25 ns
Clock Outputs
X1, X2 Crystal Oscillator 25 MHz
RXC100 Receive Clock, 100TX 25 MHz
RXC10 Receive Clock, 10T 2.5 MHz
Receive Clock Jitter 3.0 ns(pk-pk)
TXC100 Transmit Clock, 100TX 25 MHz
TXC10 Transmit Clock, 10T 2.5 MHz
Transmit Clock Jitter 1.8 ns(pk-pk)
Note 1: Exceeding the absolute rating(s) may cause permanent damage to the device. Operating at maximum conditions for extended
periods may affect device reliability.
Note 2: This device is not guaranteed to operate beyond its specified operating rating. Unused inputs must always be tied to an
appropriate logic voltage level (Ground to VDD).
Note 3: No HS (heat spreader) in package.
Note 4: Specification for packaged product only.
Note 5: 100% data transmission in full-duplex mode and minimum IPG with 130-meter cable.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
35
Timing Diagrams
10BaseT MII Transmit Timing
TXC
min. typ. max.
tSU1 TXD[3:0] Setup to TXC High 10ns
tSU2 TXEN Setup to TXC High 10ns
tHD1 TXD[3:0] Hold after TXC High 0ns
tHD2 TXEN Hold after TXC High 0ns
tCRS1 TXEN High to CRS asserted latency 4BT
tCRS2 TXEN Low to CRS de-asserted latency 8BT
tLAT TXEN High to TXP/TXM output (T X latency) 4BT
tSQE COL (SQE) Delay after TXEN de-asserted 2.5us
tSQEP COL (SQE) Pulse Duration 1.0us
tHD2
tSU2
TXEN
TXD[3:0] tSU1
tHD1
CRS tCRS2
tCRS1
TXP/TXM tLAT
Valid
Data
TXC
tSQE
COL tSQEP
SQE Timing
TXEN
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
36
100BaseTX MII Transmit Timing
TXC
tSU2
min. typ. max.
tSU1 TXD[3:0] Setup to TXC High 10ns
tSU2 TX_ER Setup to TXC High 10ns
tHD1 TXD[3:0] Hold after TXC High 0ns
tHD2 TXER Hold after TXC High 0ns
tHD3 TXEN Hold after TXC High 0ns
tCRS1 TXEN High to CRS asserted latency 4BT
tCRS2 TXEN Low to CRS de-asserted latency 4BT
tLAT TXEN High to TX+/TX- output (TX latency) 7BT
TXEN
tHD2
TXD[3:0],
TXER
tSU1
CRS
tCRS2
tCRS1
TX+/TX-
tLAT
Symbol
Out
Data
In
tHD1
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
37
100BaseTX MII Receive Timin
g
min. typ. max.
tPRXC period 40ns
tWL RXC pulse width 20ns
tWH RXC pulse width 20ns
tSU RXD[3:0], RXER, RXDV setup to rising edge of RXC 20ns
tHD RXD[3:0], RXER, RXDV hold from rising edge of RXC 20ns
tRLAT CRS to RXD latency, 4B or 5B aligned 1BT 2BT 3BT
tCRS1 "Start of Stream" to CRS asserted 140ns
tCRS2 "End of Stream" to CRS de-asserted 170ns
RX+/RX-
RXD[3:0]
RXER
CRS tCRS1
tCRS2
RXDV tRLAT
tSU
tHD
Start of
Stream
End of
Stream
RXC tWL
tWH
tP
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
38
Auto Negotiation / Fast Link Pulse Timing
tPW
min. typ. max.
tBTB FLP burst to FLP burst 8ms 16ms 24ms
tFLPW FLP burst width 2ms
tPW Clock/Data pulse width 100ns
tCTD Clock pulse to data pulse 69us
tCTC Clock pulse to clock pulse 136us
Number of Clock/Data pulses per burst 17 33
TX+/TX-
Clock
Pulse
Data
Pulse
Clock
Pulse
tPW
tCTD
tCTC
tFLPW
tBTB
TX+/TX-
Data
Pulse
FLP
Burst
FLP
Burst
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
39
Serial Management Interface Timing
min. typ. max.
tPMDC period 400 ns
tMD1 MDIO Setup to MDC (MDIO as input) 10ns
tMD2 MDIO Hold after MDC (MDIO as input) 10ns
tMD3 MDC to MDIO Valid (MDIO as output) 222ns
tMD1
Valid
Data
MDIO
(Into Chip)
Valid
Data
MDC
tMD2
MDIO
(Out of Chip)
Valid
Data
tMD3
tP
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
40
Reset Timing Diagram
tsr
Supply
Voltage
RST_N
Strap-In
Value
Reset Timing Parameters
Parameter Description Min Max Units
tsr Stable supply voltages to reset high 50 us
Reset Circuit Diagram
Micrel recommends the following discrete reset circuit as shown in Figure 1 when powering up the KS8001 device. For the
application where the reset circuit signal comes from another device (e.g., CPU, FPGA, etc), we recommend the reset circuit as
shown in Figure 2.
KS8001 CPU/FPGA
VCC
C 10uF
R 10K
RST RST_OUT_n
D1
D2
D1, D2: 1N4148
Recommended Reset Circuit
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
41
KS8001
VCC
RST
D1
D1: 1N4148
R 10K
C 10uF
Recommended Circuit for Interfacing with CPU/FPGA Reset
At power-on-reset, R, C, and D1 provide the necessary ramp rise time to reset the Micrel device. The reset out
from CPU/FPGA provides warm reset after power up. It is also recommend to power up VDD core voltage earlier
than VDDIO voltage. At worst case, the both VDD core and VDDIO voltages should come up at the same time.
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
42
Reference Circuit for Strapping Option Configuration
The Figure shows the reference circuit for strapping option pins
KS8001
LED pin
220Ω
10ΚΩ
3.3 V
Reference circuits for unmanaged programming through LED ports
KS8001
LED pin
220Ω
1ΚΩ
3.3 V
Pull Down
Pull Up
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
43
Selection of Isolation Transformers
A 1:1 isolation transformer is required at the line interface. An isolation transformer with integrated common-mode choke is
recommended for exceeding FCC requirements. The following table gives recommended transformer characteristics.
Transformer Selection Criteria
Parameter Value Test Condition
Turns Ratio 1 CT : 1 CT
Open-Circuit Inductance (min.) 350 uH 100 mV, 100 kHz, 8 mA
Leakage Inductance (max.) 0.4 uH 1 MHz (min.)
Inter-Winding Capacitance (max.) 12 pF
D.C. Resistance (max.) 0.9 Ohms
Insertion Loss (max.) 1.0 dB 0-65 MHz
HIPOT (min.) 1500 Vrms
Magnetic Vendor Selection Lists
Single Port
Magnetic manufacturer Part number AUTO MDIX Number of port
Pulse H1102 Yes 1
Bel Fuse S558-5999-U7 Yes 1
Bel Fuse SI-46001 Yes 1
Bel Fuse SI-50170 Yes 1
YCL PT163020 Yes 1
Transpower HB726 Yes 1
Delta LF8505 Yes 1
LanKom LF-H41S Yes 1
Selection of Reference Crystal
An oscillator or crystal with the following typical characteristics is recommended.
Charateristics Value Units
Frequency 25.00000 MHz
Frequency Tolerance(max) ± 50 ppm
Load Capacitance (max) 20 pF
Series Resistance 40
KS8001 Micrel
May 2005 – SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE KS8001
MICREL CONFIDENTIAL. DO NOT DISTRIBUTE.
44
Package Information