ALUMINUMELECTROLYTICCAPACITORS U U U U Specifications Item Performance Characteristics Category Temperature Range - 55 to +105C Rated Voltage Range 6.3 to 100V Rated Capacitance Range 1 to 3300F Capacitance Tolerance 20% at 120Hz, 20C Leakage Current After 2 minutes' application of rated voltage at 20C, leakage current is not more than 0.01 CV or 3 (A), whichever is greater. Measurement frequency : 120Hz at 20C 6.3 0.26 Rated voltage (V) tan (MAX.) Tangent of loss angle (tan ) 10 0.19 16 0.16 25 0.14 35 0.12 50 0.10 63 0.08 80 0.08 100 0.07 For capacitance of more than 1000F, add 0.02 for every increase of 1000F. Measurement frequency : 120Hz Rated voltage (V) 6.3 10 16 25 35 50 63 80 100 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 3 3 3 3 3 3 Z--25C / Z+20C Impedance ratio Z--40C / Z+20C ZT / Z20 (MAX.) Z--55C / Z+20C Stability at Low Temperature The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 5000 hours (2000 hours for L 10 mm: 50V or less, and for L 10mm: 63V or more) at 105C. Endurance Capacitance Change Within 30% of the initial capacitance value tan 200% or less than the initial specified value 300% or less than the initial specified value for 63V or more Leakage current Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 105C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20C. Marking Black print on the case top. Capacitance Change Within 10% of the initial capacitance value tan Less than or equal to the initial specified value Leakage current Less than or equal to the initial specified value Type numbering system (Example : 16V 100F) 1 (4 to 8 x 6.2) 5 6 7 8 9 Capacitance L1.0 Series A B C E L H DxL A0.2 E A0.2 A B C E L H H 4 x 5.8 5 x 5.8 6.3 x 5.8 6.3 x 7.7 8 x 6.2 8 x 10 10 x 7.7 10 x 10 NQ (mm) 3.3 2.9 3.2 3.2 1.8 2.1 2.4 2.4 8.3 8.3 10.3 10.3 4.3 5.3 6.6 6.6 8.3 8.3 10.3 10.3 4.3 5.3 6.6 6.6 2.3 3.1 4.5 4.5 1.0 1.3 2.2 2.2 6.2 10 7.7 10 5.8 5.8 5.8 7.7 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 10 x 13.5 12.5 x 13.5 16 x 16.5 18 x 16.5 3.2 4.8 5.4 6.4 10.3 13.6 17.1 19.1 10.3 13.6 17.1 19.1 4.5 4.0 6.3 6.3 13.5 13.5 16.5 16.5 0.8 to 1.1 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 Voltage Negative 8 x 10L, 10 x 10L, 12.5 x 13.5L, 16 x 16.5L, 18 x 16.5L : The vibration structure-resistant product is also available upon request, please ask for details. Dimension table in next page. D Code 4 to 6.3 CL 8 (6.2L) CL 10(7.7L) CL 8 (10L) * NL 10(10L,13.5L) 12.5 to 18 DxL 0.5 MAX. C0.2 B0.2 D0.5 Pressure relief vent Type Positive 0.3 MAX. Lot No. Series name Negative 2 : Except : 10 x 7.7L Plastic platform Voltage 330 F CD 50V H1015 nichicon Trade mark H L0.5 Rated voltage (16V) 0.5 MAX. B0.2 D0.5 A2 220E CD (12.5 to 18) Rated capacitance (100F) A0.2 E A0.2 0.3 MAX. Pressure 2 relief vent Capacitance Lot No. C0.2 Code GS MS ZD Size code Configuration Positive Plastic platform Series Package code Capacitance tolerance (20%) 1: Size 8 x 6.2 only Trade mark 12 13 14 Size Package 4 to 10 Taping 12.5 to 18 Taping 12.5 to 18 Tray Negative (8 x 10, 10) Voltage ( E : 25V ) 10 11 H L0.3 Capacitance Lot No. 4 A0.2 E A0.2 B0.2 D0.5 A2 47 j CD 1 Trade mark C0.2 0.3 MAX. Series 3 0.5 MAX. Plastic platform Voltage ( j : 6.3V ) 2 UCD 1 C 1 0 1 M C L 1 GS Positive 134 V 6.3 10 16 25 35 50 63 80 100 Code j A C E V H J K 2A CAT.8100H ALUMINUMELECTROLYTICCAPACITORS UCD Dimensions Cap. (F) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 1 010 4 x 5.8 2.70 60 2.2 2R2 4 x 5.8 2.70 60 3.3 3R3 4 x 5.8 2.70 60 4.7 4R7 60 10 100 4 x 5.8 1.35 90 4 x 5.8 1.35 90 15 150 4 x 5.8 1.35 90 5 x 5.8 0.70 160 4 x 5.8 1.35 90 5 x 5.8 0.70 160 5 x 5.8 0.70 160 5 x 5.8 0.70 160 6.3 x 5.8 0.36 240 5 x 5.8 0.70 160 6.3 x 5.8 0.36 240 22 220 4 x 5.8 1.35 90 4 x 5.8 1.35 90 27 270 4 x 5.8 1.35 90 5 x 5.8 0.70 160 4 x 5.8 1.35 90 5 x 5.8 0.70 160 33 330 5 x 5.8 0.70 160 4 x 5.8 1.35 90 5 x 5.8 0.70 160 47 470 56 560 5 x 5.8 0.70 68 680 6.3 x 5.8 5 x 5.8 6.3 x 5.8 100 101 160 6.3 x 5.8 0.36 240 6.3 x 5.8 0.36 240 6.3 x 5.8 0.36 0.36 240 6.3 x 5.8 0.36 240 6.3 x 5.8 0.36 0.70 160 0.36 240 240 220 221 6.3 x 5.8 0.36 240 330 331 6.3 x 7.7 0.32 8 x 6.2 0.26 390 391 1000 0.70 160 0.36 681 5 x 5.8 240 6.3 x 5.8 680 240 0.36 151 471 0.36 6.3 x 5.8 150 470 6.3 x 5.8 6.3 x 5.8 0.36 240 6.3 x 5.8 0.36 1.35 90 5 x 5.8 1.50 90 5 x 5.8 0.70 160 6.3 x 5.8 0.86 170 5 x 5.8 0.70 160 6.3 x 5.8 0.86 170 6.3 x 5.8 0.36 240 6.3 x 7.7 0.66 195 8 x 6.2 0.63 200 6.3 x 7.7 0.66 195 8 x 6.2 0.63 200 240 6.3 x 7.7 0.32 290 290 6.3 x 7.7 0.32 290 8 x 10 0.32 350 0.26 300 8 x 10 0.16 600 10 x 7.7 0.36 330 8 x 10 0.16 600 8 x 10 0.16 600 10 x 7.7 0.18 600 10 x 7.7 0.18 600 10 x 10 0.16 700 10 x 10 0.16 700 240 6.3 x 5.8 0.36 240 240 6.3 x 5.8 0.36 6.3 x 7.7 0.32 8 x 6.2 240 6.3 x 7.7 0.32 290 6.3 x 7.7 0.32 290 6.3 x 7.7 0.32 290 8 x 10 0.16 600 8 x 10 0.16 600 8 x 6.2 0.26 300 8 x 6.2 0.26 300 10 x 7.7 0.18 600 10 x 7.7 0.18 600 290 8 x 10 0.16 600 8 x 10 0.16 600 300 10 x 7.7 0.18 600 10 x 7.7 0.18 600 8 x 10 0.16 600 10 x 10 0.08 850 600 8 x 10 0.16 600 8 x 10 0.16 600 10 x 7.7 0.18 600 10 x 7.7 0.18 600 10 x 7.7 0.18 600 10 x 10 0.08 850 10 x 10 0.08 850 0.16 600 0.18 600 102 8 x 10 0.16 600 10 x 10 0.08 850 10 x 13.5 0.08 1500 152 10 x 10 0.08 850 10 x 13.5 0.08 950 12.5 x 13.5 0.08 2200 222 10 x 13.5 0.08 0.08 1100 3300 332 12.5 x 13.5 0.08 V 63 80 Cap. (F) Code 1J 1K 3.3 3R3 4.7 4R7 950 12.5 x 13.5 10 x 10 0.08 850 10 x 13.5 0.08 950 950 12.5 x 13.5 0.08 1100 50 1.50 80 6.3 x 7.7 1.20 120 8 x 6.2 1.20 120 0.08 950 12.5 x 13.5 0.08 1100 12.5 x 13.5 0.08 1100 10 x 13.5 10 x 13.5 0.14 800 12.5 x 13.5 0.12 900 12.5 x 13.5 0.12 900 16 x 16.5 0.073 1610 16 x 16.5 0.073 1610 16 x 16.5 0.035 1800 1100 16 x 16.5 0.035 1800 1100 6.3 x 5.8 Case size Rated Impedance D x L ripple (mm) 100 2A 5 x 5.8 5.00 25 6.3 x 5.8 3.00 40 6.3 x 7.7 2.40 60 8 x 6.2 2.40 60 8 x 10 1.30 130 22 220 33 330 8 x 10 0.65 250 8 x 10 1.30 47 470 8 x 10 0.65 250 10 x 10 0.70 68 680 10 x 10 0.35 400 12.5 x 13.5 100 101 10 x 10 0.35 150 151 12.5 x 13.5 220 221 12.5 x 13.5 330 331 470 471 16 x 16.5 0.082 1410 680 681 18 x 16.5 8 x 10 1.30 130 130 10 x 10 0.70 200 200 12.5 x 13.5 0.32 500 0.32 500 12.5 x 13.5 0.32 500 400 12.5 x 13.5 0.32 500 16 x 16.5 0.17 793 0.16 800 12.5 x 13.5 0.32 500 16 x 16.5 0.17 793 0.16 800 18 x 16.5 0.15 917 0.15 917 0.08 4 x 5.8 0.36 8 x 10 100 2.70 6.3 x 5.8 10 x 7.7 10 4 x 5.8 240 240 0.16 3.00 90 0.36 0.36 8 x 10 5 x 5.8 1.35 6.3 x 5.8 6.3 x 5.8 240 4 x 5.8 16 x 16.5 0.17 793 18 x 16.5 18 x 16.5 0.15 917 Case size Rated Impedance D x L ripple (mm) 1690 Max. Impedance ( ) at 20C 100kHz, Rated ripple current (mArms) at 105C 100kHz : In this case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Frequency 50Hz 120Hz 300Hz 1kHz 10kHz or more Coefficient 0.35 0.50 0.64 0.83 1.00 135 Taping specifications are given in page 23. Recommended land size, soldering by refrow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100H