DS2411R-108-00+T&R - Maxim Integrated

1-Wire is a registered trademark of Maxim Integrated Products, Inc. 1 of 12

FEATURES

 Unique, Factory-Lasered and Tested 64-Bit

Registration Number (8-Bit Family Code

Plus 48-Bit Serial Number Plus 8-Bit CRC

Tester); Guaranteed No Two Parts Alike

 Standby Current <1μA

 Built-In Multidrop Controller Enables

Multiple DS2411s to Reside on a Common

1-Wire Network

 Multidrop Compatible with Other 1-Wire

Products

 8-Bit Family Code Identifies Device as

DS2411 to the 1-Wire Master

 Low-Cost TSOC, SOT23-3, and Flip-Chip

Surface-Mount Packages

 Directly Connects to a Single-Port Pin of a

Microprocessor and Communicates at up to

15.4kbps

 Overdrive Mode Boosts Communication

Speed to 125kbps

 Operating Range: 1.5V to 5.25V, -40°C to

+85°C

PIN DESCRIPTION

NAME

SOT23 TSOC

FLIP

CHIP

I/O

VCC

GND

N.C.

—

3, 4, 5

PIN CONFIGURATION

SOT23-3, Top View

TSOC, Top View

Flip Chip, Top View with

Laser Mark, Contacts

Not Visible.

“rrd” = Revision/Date

-1rrd

A B

ORDERING INFORMATION

PART

TEMP

RANGE

PIN-

PACKAGE

DS2411R+T&R

-40°C to +85°C

3 SOT23-3

DS2411P+

-40°C to +85°C

6 TSOC

DS2411P+T&R

-40°C to +85°C

6 TSOC

DS2411X

-40°C to +85°C

4 Flip Chip*

+Denotes a lead(Pb)-free/RoHS-compliant package.

T&R = Tape and reel.

*The DS2411X is RoHS qualified and comes in tape and reel.

DESCRIPTION

The DS2411 silicon serial number is a low-cost, electronic registration number with external power

supply. It provides an absolutely unique identity that can be determined with a minimal electronic

interface (typically, a single port pin of a microcontroller). The DS2411’s registration number is a

factory-lasered, 64-bit ROM that includes a unique 48-bit serial number, an 8-bit CRC, and an 8-bit

family code (01h). Data is transferred serially through the Maxim 1-Wire protocol. The external power

supply is required, extending the operating voltage range of the device below typical 1-Wire devices.

DS2411

Silicon Serial Number with VCC

Input

19-6131; Rev 11/11

DS2411

2 of 12

ABSOLUTE MAXIMUM RATINGS

I/O Voltage to GND

-0.5V to +6V

VCC Voltage to GND

-0.5V to +6V

I/O, VCC Current

±20mA

Operating Temperature Range

-40°C to +85°C

Junction Temperature

+150°C

Storage Temperature Range

-55°C to +125°C

Lead Temperature (TSOC, SOT23-3 only; soldering, 10s)

+300°C

Soldering Temperature (reflow)

TSOC, SOT-23-3

Flip Chip

+260°C

+240°C

This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the

operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of

time may affect reliability.

ELECTRICAL CHARACTERISTICS (VCC = 1.5V to 5.25V; TA = -40°C to +85°C.)

PARAMETER

SYMBOL

CONDITIONS

MIN

MAX

UNITS

Operating Temperature TA (Note 1) -40 +85 °C

Supply Voltage VCC (Note 1) 1.5 5.25 V

1-Wire Pullup VCC = VPUP (Note 1) 1.5 5.25 V

I/O PIN GENERAL DATA

1-Wire Pullup Resistance

RPUP

(Notes 1, 2)

0.3

2.2

kΩ

Power-Up Delay tPWRP

stable to first

1-Wire command (Notes 1, 3)

1200 µs

Input Capacitance

CIO

(Note 3)

100

Input Load Current

0V ≤ V(I/O) ≤ VCC

-1

µA

Standby Supply Current

ICCS

V(I/O) ≤ VIL, or V(I/O) ≥ VIH

µA

Active Supply Current

ICCA

100

µA

High-to-Low Switching

Threshold

VTL (Notes 3, 4, 5) 0.4 3.2 V

Input Low Voltage

VIL

(Note 1)

0.30

Input High Voltage VIH (Note 1)

0.3

Low-to-High Switching

Threshold

VTH (Notes 3, 4, 6) 0.75 3.4 V

Switching Hysteresis

VHY

(Notes 3, 7)

0.18

Output Low Voltage at 4mA

VOL

(Note 8)

0.4

Rising Edge Holdoff tREH

Standard speed (Note 9, 3)

1.25

µs

Overdrive speed (Note 9, 3)

0.5

Recovery Time tREC

Standard speed,

RPUP = 2.2kΩ (Note 1)

µs

Overdrive speed,

RPUP = 2.2kΩ (Note 1)

Overdrive speed, directly prior to

reset pulse; RPUP = 2.2kΩ (Note 1)

DS2411

3 of 12

PARAMETER

SYMBOL

CONDITIONS

MIN

MAX

UNITS

Timeslot Duration tSLOT

Standard speed

µs

Overdrive VCC ≥ 2.2V

Overdrive VCC ≥ 1.5V

I/O PIN, 1-Wire RESET, PRESENCE DETECT CYCLE

Reset Low Time

RSTL

Standard speed

480

640

µs

Overdrive speed

Presence-Detect High Time tPDH

Standard speed

µs

Overdrive VCC ≥ 2.2V

Overdrive VCC ≥ 1.5V

8.5

Presence-Detect Low Time tPDL

Standard speed

240

µs

Overdrive VCC ≥ 2.2V

Overdrive VCC ≥ 1.5V

Presence-Detect Fall Time tFPD

Standard speed (Note 10, 3)

0.4

µs

Overdrive speed (Note 10, 3)

0.05

Presence-Detect Sample

Time tMSP

Standard speed (Note 1)

µs

Overdrive VCC ≥ 2.2V (Note 1)

Overdrive VCC ≥ 1.5V (Note 1)

8.5

I/O PIN, 1-Wire WRITE

Write-0 Low Time tW0L

Standard speed (Notes 1, 11, 13)

120

µs

Overdrive V

≥ 2.2V

(Notes 1, 11, 13)

6 16

Overdrive V

≥ 1.5V

(Notes 1, 11, 13)

8 16

Write-1 Low Time tW1L

Standard speed (Notes 1, 11, 13)

µs

Overdrive speed (Notes 1, 11, 13)

I/O PIN, 1-Wire READ

Read Low Time tRL

Standard speed (Notes 1, 12)

15 - δ

µs

Overdrive speed (Notes 1, 12)

2 - δ

Read Sample Time tMSR

Standard speed (Notes 1, 12)

tRL + δ

µs

Overdrive speed (Notes 1, 12)

tRL + δ

Note 1: System requirement.

Note 2: Maximum allowable pullup resistance is a function of the number of 1-Wire devices in the

system and 1-Wire recovery times. The specified value here applies to systems with only

one device and with the minimum 1-Wire recovery times. For more heavily loaded

systems, an active pullup such as that found in the DS2480B may be required. Minimum

allowable pullup resistance is slightly greater than the value necessary to produce the

absolute maximum current (20mA) during 1-Wire low times at VPUP = 5.25V assuming

VOL = 0V.

Note 3: Not production tested.

Note 4: VTL and VTH are functions of VCC and temperature. The VTH and VTL maximum specifica-

tions are valid at VCC = 5.25V. In any case, VTL < VTH < VCC.

Note 5: Voltage below which during a falling edge on I/O, a logic ‘0’ is detected.

Note 6: Voltage above which during a rising edge on I/O, a logic ‘1’ is detected.

Note 7: After VTH is crossed during a rising edge on I/O, the voltage on I/O has to drop by VHY to

be detected as logic ‘0’.

Note 8: The I-V characteristic is linear for voltages less than 1V.

DS2411

4 of 12

Note 9: The earliest recognition of a negative edge is possible at tREH after VTH has been reached

on the previous edge.

Note 10: Interval during the negative edge on I/O at the beginning of a presence-detect pulse

between the time at which the voltage is 90% of VPUP and the time at which the voltage is

10% of VPUP.

Note 11: ε in Figure 7 represents the time required for the pullup circuitry to pull the voltage on I/O

up VIL to VTH. The actual maximum duration for the master to pull the line low is tW1LMAX

+ tF - ε and tW0LMAX + tF - ε, respectively.

Note 12: δ in Figure 7 represents the time required for the pullup circuitry to pull the voltage on I/O

up from VIL to the input-high threshold of the bus master. The actual maximum duration

for the master to pull the line low is tRLMAX + tF.

Note 13: Interval begins when the voltage drops below VTL during a negative edge on I/O and ends

when the voltage rises above VTH during a positive edge on I/O.

OPERATION

The DS2411’s registration number is accessed through a single data line. The 48-bit serial number, 8-bit

family code, and 8-bit CRC are retrieved using the Maxim 1-Wire protocol. This protocol defines bus

transactions in terms of the bus state during specified time slots that are bus-master-generated falling

edges on the I/O pin. All data is read and written least significant bit first. The device requires a delay

between VCC power-up and initial 1-Wire communication, tPWRP (1200µs). During this time the device

may issue presence-detect pulses.

1-Wire BUS SYSTEM

The 1-Wire bus has a single bus master and one or more slaves. In all instances, the DS2411 is a slave

device. The bus master is typically a microcontroller. The discussion of this bus system is broken down

into three topics: hardware configuration, transaction sequence, and 1-Wire signaling (signal type and

timing).

Hardware Configuration

The 1-Wire bus has a single data line, I/O. It is important that each device on the bus be able to drive I/O

at the appropriate time. To facilitate this, each device has an open-drain or three-state output. The

DS2411 has an open-drain output with an internal circuit equivalent to that shown in Figure 3. The bus

master can have the same equivalent circuit. If a bidirectional pin is not available on the master, separate

output and input pins can be connected together. The bus requires a pullup resistor at the master end of

the bus, as shown in Figure 4. A multidrop bus consists of a 1-Wire bus with multiple slaves attached.

The 1-Wire bus has a maximum data rate of 15.4kbps in standard speed and 125kbps in overdrive.

The idle state for the 1-Wire bus is high. If a transaction needs to be suspended for any reason, I/O must

remain high if the transaction is to be resumed. If the bus is pulled low, slave devices on the bus will

interpret the low as either a timeslot, or a reset depending on the duration.

Figure 1. DS2411 REGISTRATION NUMBER

MSB

LSB

8-BIT CRC CODE 48-BIT SERIAL NUMBER 8-BIT FAMILY CODE

(01h)

MSB

LSB

MSB

LSB

MSB

LSB

DS2411

5 of 12

Figure 2. 1-WIRE CRC GENERATOR

POLYNOMIAL = X8 + X5 + X4 + 1

1st

STAGE

2nd

STAGE

3rd

STAGE

4th

STAGE

6th

STAGE

5th

STAGE

7th

STAGE

8th

STAGE

INPUT DATA

Figure 3. DS2411 EQUIVALENT CIRCUIT

100Ω

MOSFET

VCC

I/O

-1µA ≤

IL ≤ 1µA

GROUND

Figure 4. BUS MASTER CIRCUIT

OPEN-DRAIN

PORT PIN

BUS MASTER

DS5000 OR 8051

EQUIVALENT

VCC to DS2411

RPUP

I/O to DS2411

Ground to DS2411

RPUP must be between 0.3 kΩ and 2.2 kΩ. The optimal

value depends on the 1-Wire communication speed and

the bus load characteristics.

DS2411

6 of 12

TRANSACTION SEQUENCE

The communication sequence for accessing the DS2411 through the 1-Wire bus is as follows:

 Initialization

 ROM Function Command

 Read Data

INITIALIZATION

All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence

consists of a reset pulse transmitted by the bus master followed by a presence pulse(s) transmitted by the

slave(s). The presence pulse lets the bus master know that the DS2411 is on the bus and is ready to

operate. For more details, see the 1-Wire Signaling section.

ROM FUNCTION COMMANDS

Once the bus master has detected a presence, it can issue one of the three ROM function commands. All

ROM function command codes are 1 byte long. A list of these commands follows (see the flowchart in

Figure 5).

Read ROM [33h]

This command allows the bus master to read the DS2411’s 8-bit family code, unique 48-bit serial

number, and 8-bit CRC. This command should only be used if there is a single slave device on the bus. If

more than one slave is present on the bus, a data collision results when all slaves try to transmit at the

same time (open drain produces a wired-AND result), and the resulting registration number read by the

master will be invalid.

Search ROM [F0h]

When a system is initially brought up, the bus master might not know the number of devices on the

1-Wire bus or their registration numbers. By taking advantage of the wired-AND property of the bus, the

master can use a process of elimination to identify the registration numbers of all slave devices. For each

bit of the registration number, starting with the least significant bit, the bus master issues a triplet of time

slots. On the first slot, each slave device participating in the search outputs the true value of its

registration number bit. On the second slot, each slave device participating in the search outputs the

complemented value of its registration number bit. On the third slot, the master writes the true value of

the bit to be selected. All slave devices that do not match the bit written by the master stop participating

in the search. If both of the read bits are zero, the master knows that slave devices exist with both states of

the bit. By choosing which state to write, the bus master branches in the romcode tree. After one complete

pass, the bus master knows the registration number of a single device. Additional passes identify the

registration numbers of the remaining devices. Refer to App Note 187: 1-Wire Search Algorithm for a

detailed discussion, including an example.

Overdrive Skip ROM [3Ch]

This command causes all overdrive-capable slave devices on the 1-Wire network to enter overdrive speed

(OD = 1). All communication following this command has to occur at overdrive speed until a reset pulse

of minimum 480µs duration resets all devices on the bus to regular speed (OD = 0).

To subsequently address a specific overdrive-supporting device, a reset pulse at overdrive speed has to be

issued followed by a read ROM or search ROM command sequence. Overdrive speeds up the time for the

search process.

DS2411

7 of 12

Figure 5. ROM FUNCTIONS FLOW CHART

DS2411 Tx

CRC Byte

DS2411 Tx

Serial Number

(6 Bytes)

DS2411 Tx

Family Code

(1 Byte)

33h

Read ROM

Command?

Bit 63

Match?

DS2411 Tx Bit 0

Master Tx Bit 0

DS2411 Tx Bit 1

Master Tx Bit 1

DS2411 Tx Bit 63

Master Tx Bit 63

Bit 1

Match?

Bit 0

Match?

F0h

Search ROM

Command?

Bus Master Tx ROM

Function Command

DS2411 Tx

Presence Pulse

Reset Pulse ?

OD = 0

Bus Master Tx

Reset Pulse

3Ch

OD Skip

Command?

OD = 1

DS2411

8 of 12

1-WIRE SIGNALING

The DS2411 requires strict protocols to ensure data integrity. The protocol consists of four types of

signaling on one line: Reset Sequence with Reset Pulse and Presence Pulse, Write 0, Write 1, and Read

Data. Except for the presence pulse the bus master initiates all these signals. The DS2411 can

communicate at two different speeds: standard speed and Overdrive speed. If not explicitly set into the

Overdrive mode, the DS2411 will communicate at standard speed. While in Overdrive Mode the fast

timing applies to all waveforms.

To get from idle to active, the voltage on the 1-Wire line needs to fall from VPUP below the threshold VTL.

To get from active to idle, the voltage needs to rise from VILMAX past the threshold VTH. The voltage

VILMAX is relevant for the DS2411 when determining a logical level, but not for triggering any events.

The initialization sequence required to begin any communication with the DS2411 is shown in Figure 6.

A Reset Pulse followed by a Presence Pulse indicates the DS2411 is ready to receive data, given the

correct ROM and memory function command. In a mixed population network, the reset low time tRSTL

needs to be long enough for the slowest 1-Wire slave device to recognize it as a reset pulse. If the bus

master uses slew-rate control on the falling edge, it must pull down the line for tRSTL + tF to compensate

for the edge. A tRSTL duration of 480µs or longer will exit the Overdrive Mode returning the device to

standard speed. If the DS2411 is in Overdrive Mode and tRSTL is no longer than 80µs, the device will

remain in Overdrive Mode.

After the bus master has released the line it goes into receive mode (RX). Now, the 1-Wire bus is pulled

to VPUP via the pullup resistor or, in case of a DS2480B driver, by active circuitry. When the threshold

VTH is crossed, the DS2411 waits for tPDH and then transmits a Presence Pulse by pulling the line low for

tPDL. To detect a presence pulse, the master must test the logical state of the 1-Wire line at tMSP.

The tRSTH window must be at least the sum of tPDHMAX, tPDLMAX, and tRECMIN. Immediately after tRSTH is

expired, the DS2411 is ready for data communication. In a mixed population network, tRSTH should be

extended to minimum 480µs at standard speed and 48µs at Overdrive speed to accommodate other 1-

Wire devices.

Read/Write Time Slots

Data communication with the DS2411 takes place in time slots that carry a single bit each. Write time

slots transport data from bus master to slave. Read time-slots transfer data from slave to master. The

definitions of the write and read time slots are illustrated in Figure 7.

All communication begins with the master pulling the data line low. As the voltage on the 1-Wire line

falls below the threshold VTL, the DS2411 starts its internal timing generator that determines when the

data line will be sampled during a write time slot and how long data will be valid during a read time slot.

Master to Slave

For a write-one time slot, the voltage on the data line must have crossed the VTHMAX threshold after the

write-one low time tW1LMAX is expired. For a write-zero time slot, the voltage on the data line must stay

below the VTHMIN threshold until the write-zero low time tW0LMIN is expired. For most reliable

communication the voltage on the data line should not exceed VILMAX during the entire tW0L window.

After the VTHMAX threshold has been crossed, the DS2411 needs a recovery time tREC before it is ready for

the next time slot.

DS2411

9 of 12

INITIALIZATION PROCEDURE

Figure 6. Reset and Presence Pulse

READ/WRITE TIMING DIAGRAM

Figure 7a. Write-One Time Slot

Figure 7b. Write-Zero Time Slot

Figure 7c. Read-data Time Slot

DS2411

10 of 12

Slave to Master

A read-data time slot begins like a write-one time slot. The voltage on the data line must remain below

VTLMIN until the read low time tRL is expired. During the tRL window, when responding with a 0, the

DS2411 will start pulling the data line low; its internal timing generator determines when this pull-down

ends and the voltage starts rising again. When responding with a 1, the DS2411 will not hold the data line

low at all, and the voltage starts rising as soon as tRL is over.

The sum of tRL + δ (rise rime) on one side and the internal timing generator of the DS2411 on the other

side define the master sampling window (tMSRMIN to tMSRMAX) in which the master must perform a read

from the data line. For most reliable communication, tRL should be as short as permissible and the master

should read close to but no later than tMSRMAX. After reading from the data line, the master must wait until

tSLOT is expired. This guarantees sufficient recovery time tREC for the DS2411 to get ready for the next

time slot.

Improved Network Behavior

In a 1-Wire environment, line termination is possible only during transients controlled by the bus master

(1-Wire driver). 1-Wire networks therefore are susceptible to noise of various origins. Depending on the

physical size and topology of the network, reflections from end points and branch points can add up or

cancel each other to some extent. Such reflections are visible as glitches or ringing on the 1-Wire

communication line. A glitch during the rising edge of a time slot can cause a slave device to lose

synchronization with the master and, as a consequence, result in a search ROM command coming to a

dead end. For better performance in network applications, the DS2411 uses a new 1-Wire front end,

which makes it less sensitive to noise and also reduces the magnitude of noise injected by the slave

device itself.

The 1-Wire front end of the DS2411 differs from traditional slave devices in four characteristics.

1) The falling edge of the presence pulse has a controlled slew rate. This provides a better match to the

line impedance than a digitally switched transistor, converting the high frequency ringing known from

traditional devices into a smoother low-bandwidth transition. The slew rate control is specified by the

parameter tFPD, which has different values for standard and Overdrive speed.

2) There is additional low-pass filtering in the circuit that detects the falling edge at the beginning of a

time slot. This reduces the sensitivity to high-frequency noise. As a consequence, the duration of the

setup time tSU at standard speed is larger than with traditional devices. This additional filtering does

not apply at Overdrive speed.

3) There is a hysteresis at the low-to-high switching threshold VTH. If a negative glitch crosses VTH but

doesn’t go below VTH - VHY, it will not be recognized (Figure 8, Case A). The hysteresis is effective

at any 1-Wire speed.

4) There is a time window specified by the rising edge hold-off time tREH during which glitches will be

ignored, even if they extend below VTH - VHY threshold (Figure 8, Case B, tGL < tREH). Deep voltage

droops or glitches that appear late after crossing the VTH threshold and extend beyond the tREH

window cannot be filtered out and will be taken as beginning of a new time slot (Figure 8, Case C, tGL

≥ tREH). The duration of the hold-off time is independent of the 1-Wire speed.

Only devices which have the parameters tFPD, VHY and tREH specified in their electrical characteristics use

the improved 1-Wire front end.

DS2411

11 of 12

NOISE SUPPRESSION SCHEME Figure 8

VPUP

VTH

VHY

tREH

tGL

tREH

tGL

Case A

Case C

Case B

CRC GENERATION

To validate the registration number transmitted from the DS2411, the bus master can generate a CRC

value from the 8-bit family code and unique 48-bit serial number as it is received. If the CRC matches the

last 8 bits of the registration number, the transmission is error free.

The equivalent polynomial function of this CRC is: CRC = x8 + x5 + x4 + 1. For more information on

generating CRC values see Application Note 27.

CUSTOM DS2411

Customization of a portion of the unique 48-bit serial number by the customer is available. Maxim will

significant bits are selectable by the customer as a starting value, and the least significant bits are non-

selectable and will be automatically incremented by one. Certain quantities and conditions apply for these

custom parts. Contact your Maxim sales representative for more information.

PACKAGE INFORMATION

For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages.

Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a

different suffix character, but the drawing pertains to the package regardless of RoHS status.

PACKAGE TYPE PACKAGE CODE OUTLINE NO.

LAND PATTERN

SOT23-3 U3+3 21-0051

90-0179

6 TSOC D6+1 21-0382

90-0321

4 Flip Chip BF411-1 21-0282

Refer to 21-0282

DS2411

12 of 12

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim

reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600

REVISION HISTORY

REVISION

DATE

DESCRIPTION

PAGES

CHANGED

020703

Initial release

—

052003

Corrected the Flip Chip pin configuration.

Section 1-Wire Signaling rewritten.

8, 10

Added section Improved Network Behavior.

10, 11

122106

Added flip chip top marking and URL to package outline drawing.

Added SOT23-3 and TSOC lead-free part numbers to Ordering

Information.

11/11

Updated ordering information, lead temperature, soldering temperature.

1, 2

In the Electrical Characteristics table, applied note 11 to the t

W0L

specification; deleted ε from the tW1L specification; corrected the tRL

specification (replaced ε with δ, applied note 12), and added more

details to notes 4, 11 and 12.

3, 4

Deleted the DS2480B (5V operation) master circuit from Figure 4. 5

Updated the

Package Information

section and added

Revision History

. 11, 12