LM4865 www.ti.com LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 750 mW Audio Power Amplifier with DC Volume Control and Headphone Switch Check for Samples: LM4865 FEATURES DESCRIPTION * * * * The LM4865 is a mono bridged audio power amplifier with DC voltage volume control. The LM4865 is capable of delivering 750mW of continuous average power into an 8 load with less than 1% THD when powered by a 5V power supply. Switching between bridged speaker mode and headphone (single ended) mode is accomplished using the headphone sense pin. To conserve power in portable applications, the LM4865's micropower shutdown mode (IQ = 0.7A, typ) is activated when less than 300mV is applied to the DC Vol/SD pin. 1 2 * DC Voltage Volume Control Headphone Amplifier Mode "Click and Pop" Suppression Shutdown Control When Volume Control Pin Is Low Thermal Shutdown Protection APPLICATIONS * * * GSM Phones and Accessories, DECT, Office Phones Hand Held Radio Other Portable Audio Devices Boomer audio power amplifiers are designed specifically to provide high power audio output while maintaining high fidelity. They require few external components and operate on low supply voltages. KEY SPECIFICATION * * * * PO at 1.0% THD+N Into 8 SOIC, Micro SMD 750 mW (typ) PO at 10% THD+N Into 8 SOIC, Micro SMD 1W (typ) Shutdown Current 0.7A(typ) Supply Voltage Range 2.7V to 5.5 V CONNECTION DIAGRAMS Figure 1. Micro SMD Package (Top View) Figure 2. Small Outline Package (SOIC) (Top View) Mini Small Outline Package (VSSOP) See Package Number D, DGK 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2013, Texas Instruments Incorporated LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 www.ti.com TYPICAL APPLICATION Figure 3. Typical Audio Amplifier Application Circuit (Numbers in ( ) are specific to the micro SMD package) 2 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 LM4865 www.ti.com SNAS035G - DECEMBER 1999 - REVISED MAY 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ABSOLUTE MAXIMUM RATINGS (1) (2) Supply Voltage 6.0V -65C to +150C Storage Temperature -0.3V to VDD +0.3V Input Voltage Power Dissipation (3) Internally Limited ESD Susceptibility (4) 2000V ESD Susceptibility (5) 200V Junction Temperature Soldering Information Thermal Resistance (1) (2) (3) (4) (5) 150C Vapor Phase (60 sec.) 215C Infrared (15 sec.) 220C JC (SOIC) 35C/W JA (SOIC) 150C/W JC (VSSOP) 56C/W JA (VSSOP) 190C/W JA (micro SMD) 150C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions that ensure specific performance limits. This assumes that the device operates within the Operating Ratings. Specifications are not ensured for parameters where no limit is given. The typical value, however, is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA)/JA or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4865M, TJMAX = 150C. Human body model, 100pF discharged through a 1.5k resistor. Machine Model, 220pF-240pF discharged through all pins. OPERATING RATINGS Temperature Range TMIN TA TMAX -40C TA +85C 2.7V VDD 5.5V Supply Voltage Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 3 LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 ELECTRICAL CHARACTERISTICS www.ti.com (1) (2) The following specifications apply for VDD = 5V, unless otherwise specified. Limits apply for TA = 25C. Symbol Parameter VDD Conditions Supply Voltage Typical (4) Max (3) Units 5.5 V VIN = 0V, IO = 0A, HP Sense = 0V 4 7 mA VIN = 0V, IO - 0A, HP Sense = 5V 3.5 6 mA 0.7 50 mV Quiescent Power Supply Current ISD Shutdown Current VPIN4 0.3V VOS Output Offset Voltage VIN = 0V 5 THD = 1% (max), HP Sense < 0.8V, f = 1kHz, RL = 8 Output Power Min 2.7 IDD PO LM4865 (3) 500 A 750 mW THD = 10% (max), HP Sense < 0.8V, f = 1kHz, RL = 8 1.0 W THD + N = 1%, HP Sense > 4V, f = 1kHz, RL = 32 80 mW THD = 10%, HP Sense > 4V, f = 1kHz, RL = 32 110 mW THD+N Total Harmonic Distortion + Noise PO = 300 mWrms, f = 20Hz-20kHz, RL = 8 0.6 % PSRR Power Supply Rejection Ratio VRIPPLE = 200mVrms, RL = 8, CB = 1.0 F, f = 1kHz 50 dB GainRANGE Single-Ended Gain Range VIH HP Sense High Input Voltage VIL HP Sense Low Input Voltage (1) (2) (3) (4) Gain with VPIN4 4.0V, (80% of VDD) 18.8 20 dB Gain with VPIN4 0.9V, (18% of VDD) -70 -72 dB 4 V 0.8 V All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions that ensure specific performance limits. This assumes that the device operates within the Operating Ratings. Specifications are not ensured for parameters where no limit is given. The typical value, however, is a good indication of device performance. Limits are ensured to AOQL (Average Outgoing Quality Level). Typicals are measured at 25C and represent the parametric norm. EXTERNAL COMPONENTS DESCRIPTION (Figure 3 ) Components 4 Functional Description 1. Ci Input coupling capacitor which blocks the DC voltage at the amplifier's input terminals. It also creates a highpass filter with the internal Ri. The designer should note that10kOhm<(Ri)<110kOhm.Therefore fc = 1/(2RiCi). Refer to the section, PROPERLY SELECTING EXTERNAL COMPONENTS , for an explanation of how to determine the value of Ci. 2. CS Supply bypass capacitor which provides power supply filtering. Refer to the POWER SUPPLY BYPASSING section for information concerning proper placement and selection of the supply bypass capacitor. 3. CB Bypass pin capacitor which provides half-supply filtering. Refer to the section, PROPERLY SELECTING EXTERNAL COMPONENTS, for information concerning proper placement and selection of CB. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 LM4865 www.ti.com SNAS035G - DECEMBER 1999 - REVISED MAY 2013 TYPICAL PERFORMANCE CHARACTERISTICS THD+N vs Frequency THD+N vs Frequency Figure 4. Figure 5. THD+N vs Output Power THD+N vs Output Power Figure 6. Figure 7. THD+N vs Output Power THD+N vs Output Power Figure 8. Figure 9. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 5 LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) 6 Power Dissipation vs Load Resistance Power Dissipation vs Output Power Figure 10. Figure 11. Power Derating Curve Clipping Voltage vs RL Figure 12. Figure 13. Noise Floor Frequency Response vs Input Capacitor Size Figure 14. Figure 15. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 LM4865 www.ti.com SNAS035G - DECEMBER 1999 - REVISED MAY 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Power Supply Rejection Ratio Attenuation Level vs DC-Vol Amplitude Figure 16. Figure 17. THD+N vs Frequency THD+N vs Frequency Figure 18. Figure 19. THD+N vs Frequency THD+N vs Output Power Figure 20. Figure 21. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 7 LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 www.ti.com TYPICAL PERFORMANCE CHARACTERISTICS (continued) THD+N vs Output Power THD+N vs Output Power Figure 22. Figure 23. Output Power vs Load Resistance Clipping Voltage vs Supply Voltage Figure 24. Figure 25. Output Power vs Supply Voltage Figure 26. 8 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 LM4865 www.ti.com SNAS035G - DECEMBER 1999 - REVISED MAY 2013 TYPICAL PERFORMANCE CHARACTERISTICS (continued) Output Power vs Supply Voltage Supply Current vs Supply Voltage Figure 27. Figure 28. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 9 LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 www.ti.com APPLICATION INFORMATION BRIDGE CONFIGURATION EXPLANATION As shown in Figure 3, the LM4865 consists of two operational amplifiers internally. An external DC voltage sets the closed-loop gain of the first amplifier, whereas two internal 20k resistors set the second amplifier's gain at 1. The LM4865 can be used to drive a speaker connected between the two amplifier outputs or a monaural headphone connected between VO1 and GND. Figure 3 shows that the output of Amp1 serves as the input to Amp2. This results in both amplifiers producing signals that are identical in magnitude, but 180 out of phase. Taking advantage of this phase difference, a load placed between VO1 and VO2 is driven differentially (commonly referred to as "bridge mode" ). This mode is different from single-ended driven loads that are connected between a single amplifier's output and ground. Bridge mode has a distinct advantage over the single-ended configuration: its differential drive to the load doubles the output swing for a specified supply voltage. This results in four times the output power when compared to a single-ended amplifier under the same conditions. This increase in attainable output assumes that the amplifier is not current limited or the output signal is not clipped. Another advantage of the differential bridge output is no net DC voltage across load. This results from biasing VO1 and VO2 at half-supply. This eliminates the coupling capacitor that single supply, single-ended amplifiers require. Eliminating an output coupling capacitor in a single-ended configuration forces a single supply amplifier's half-supply bias voltage across the load. The current flow created by the half-supply bias voltage increases internal IC power dissipation and may permanently damage loads such as speakers. POWER DISSIPATION Power dissipation is a major concern when designing a successful bridged or single-ended amplifier. Equation 1 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (VDD)2/(22RL) Single-Ended (1) However, a direct consequence of the increased power delivered to the load by a bridge amplifier is an increase in internal power dissipation point for a bridge amplifier operating at the same given conditions. PDMAX = 4*(VDD)2/(22RL) Bridge Mode (2) The LM4865 has two operational amplifiers in one package and the maximum internal power dissipation is 4 times that of a single-ended amplifier. However, even with this substantial increase in power dissipation, the LM4865 does not require heatsinking. From Equation 2, assuming a 5V power supply and an 8 load, the maximum power dissipation point is 633 mW. The maximum power dissipation point obtained from Equation 2 must not be greater than the power dissipation that results from Equation 3: PDMAX = (TJMAX-TA)/JA (3) For the micro SMD and SOIC packages, JA = 150C/W. The VSSOP package has a 190C/W JA. TJMAX = 150C for the LM4865. For a given ambient temperature TA, Equation 3 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 2 is greater than that of Equation 3, then either decrease the supply voltage, increase the load impedance, or reduce the ambient temperature. For a typical application using the micro SMD or SOIC packaged LM4865, a 5V power supply, and an 8 load, the maximum ambient temperature that does not violate the maximum junction temperature is approximately 55C. The maximum ambient temperature for the VSSOP package with the same conditions is approximately 30C. These results further assume that a device is a surface mount part operating around the maximum power dissipation point. Since internal power dissipation is a function of output power, higher ambient temperatures are allowed as output power decreases. Refer to the TYPICAL PERFORMANCE CHARACTERISTICS curves for power dissipation information at lower output power levels. 10 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 LM4865 www.ti.com SNAS035G - DECEMBER 1999 - REVISED MAY 2013 POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection. The capacitors connected to the bypass and power supply pins should be placed as close to the LM4865 as possible. The capacitor connected between the bypass pin and ground improves the internal bias voltage's stability, producing improved PSRR. The improvements to PSRR increase as the bypass pin capacitor value increases. Typical applications employ a 5V regulator with 10F and a 0.1F filter capacitors that aid in supply stability. Their presence, however does not eliminate the need for bypassing the supply nodes of the LM4865. The selection of bypass capacitor values, especially CB, depends on desired PSRR requirements, click and pop performance (as explained in the section, PROPERLY SELECTING EXTERNAL COMPONENTS), system cost, and size constraints. DC VOLTAGE VOLUME CONTROL The LM4865 has internal volume control that is controlled by the DC voltage applied its DC Vol/SD pin (pin 5 on the micro SMD and pin 4 on the VSSOP and SOIC packages). The volume control's input range is from GND to VDD. A graph showing a typical volume response versus input control voltage is shown in the TYPICAL PERFORMANCE CHARACTERISTICS section. The DC Vol/SD pin also functions as the control pin for the LM4865's micropower shutdown feature. See the MUTE AND SHUTDOWN FUNCTION section for more information. Like all volume controls, the LM4865's internal volume control is set while listening to an amplified signal that is applied to an external speaker. The actual voltage applied to the DC Vol/SD pin is a result of the volume a listener desires. As such, the volume control is designed for use in a feedback system that includes human ears and preferences. This feedback system operates quite well without the need for accurate gain. The user simply sets the volume to the desired level as determined by their ear, without regard to the actual DC voltage that produces the volume. Therefore, the accuracy of the volume control is not critical, as long as volume changes monotonically and step size is small enough to reach a desired volume that is not too loud or too soft. Since gain accuracy is not critical, there will be volume variation from part-to-part even with the same applied DC control voltage. The gain of a given LM4865 can be set with a fixed external voltage, but another LM4865 may require a different control voltage to achieve the same gain. Figure 29 is a curve showing the volume variation of twenty typical LM4865s as the voltage applied to the DC Vol/SD pin is varied. For gains greater than unity, the typical part-to-part variation can be as large as 8dB for the same control voltage. Figure 29. Typical Part-to-Part Gain Variation as a Function of DC-Vol Control Voltage MUTE AND SHUTDOWN FUNCTION The LM4865's mute and shutdown functions are controlled through the DC Vol/SD pin. Mute is activated by applying a voltage in the range of 500mV to 1V. A typical attenuation of 75dB is achieved is while mute is active. The LM4865's micropower shutdown mode turns off the amplifier's bias circuitry. The micropower shutdown mode is activated by applying less than 300mVDC to the DC Vol/SD pin. When shutdown is active, they supply current is reduced to 0.7A (typ). A degree of uncertainty exists when the voltage applied to the DC Vol/SD pin is in the range of 300mV to 500mV. The LM4865 can be in mute, still fully powered, or in micropower shutdown and fully muted. In mute mode, the LM4865 draws the typical quiescent supply current. The DC Vol/SD pin should be tied to GND for best shutdown mode performance. As the DC Vol/SD is increased above 0.5V the amplifier will follow the attenuation curve in TYPICAL PERFORMANCE CHARACTERISTICS. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 11 LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 www.ti.com HP-Sense FUNCTION Applying a voltage between 4V and VCC to the LM4865's HP-Sense headphone control pin turns off Amp2 and mutes a bridged-connected load. Quiescent current consumption is reduced when the IC is in this single-ended mode. Figure 30 shows the implementation of the LM4865's headphone control function. With no headphones connected to the headphone jack, the R1-R2 voltage divider sets the voltage applied to the HP-Sense pin (pin 3) at approximately 50mV. This 50mV enables the LM4865 and places it in bridged mode operation. While the LM4865 operates in bridged mode, the DC potential across the load is essentially 0V. Since the HPSense threshold is set at 4V, even in an ideal situation, the output swing cannot cause a false single-ended trigger. Connecting headphones to the headphone jack disconnects the headphone jack contact pin from VO1 and allows R1 to pull the HP Sense pin up to VCC. This enables the headphone function, turns off Amp2, and mutes the bridged speaker. The amplifier then drives the headphones, whose impedance is in parallel with resistor R2. Resistor R2 has negligible effect on output drive capability since the typical impedance of headphones is 32. The output coupling capacitor blocks the amplifier's half supply DC voltage, protecting the headphones. A microprocessor or a switch can replace the headphone jack contact pin. When a microprocessor or switch applies a voltage greater than 4V to the HP Sense pin, a bridge-connected speaker is muted and Amp1 drives the headphones. PROPERLY SELECTING EXTERNAL COMPONENTS Optimizing the LM4865's performance requires properly selecting external components. Though the LM4865 operates well when using external components having wide tolerances, the best performance is achieved by optimizing component values. Figure 30. Headphone Circuit Input Capacitor Value Selection Amplification of the lowest audio frequencies requires high value input coupling capacitors. These high value capacitors can be expensive and may compromise space efficiency in portable designs. In many cases, however, the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 150Hz. In application 5 using speakers with this limited frequency response, a large input capacitor will offer little improvement in system performance. Figure 3 shows that the nominal input impedance (RIN) is 10k at maximum volume and 110k at minimum volume. Together, the input capacitor, Ci, and RIN, produce a -3dB high pass filter cutoff frequency that is found using Equation 4. (4) 12 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 LM4865 www.ti.com SNAS035G - DECEMBER 1999 - REVISED MAY 2013 As the volume changes from minimum to maximum, RIN decrease from 110k to 10k. Equation 4 reveals that the -3dB frequency will increase as the volume increases. The nominal value of Ci for lowest desired frequency response should be calculated with RIN = 10k . As an example when using a speaker with a low frequency limit of 150Hz, Ci, using Equation 4 is 0.1F. The 0.22F Ci shown in Figure 3 is optimized for a speaker whose response extends down to 75Hz. Bypass Capacitor Value Selection Besides minimizing the input capacitor size, careful consideration should be paid to value of the bypass capacitor CB. Since CB determines how fast the LM4865 turns on, its value is the most critical when minimizing turn-on pops. The slower the LM4865's outputs ramp to their quiescent DC voltage (nominally VDD/2), the smaller the turn-on pop. Choosing CB equal to 1.0F, along with a small value of Ci (in the range of 0.1F to 0.39F), produces a clickless and popless shutdown function. Choosing Ci as small as possible helps minimize clicks and pops. CLICK AND POP CIRCUITRY The LM4865 contains circuitry that minimizes turn-on and shutdown transients or "clicks and pops". For this discussion, turn-on refers to either applying the power supply voltage or when the shutdown mode is deactivated. While the power supply is ramping to its final value, the LM4865's internal amplifiers are configured as unity gain buffers. An internal current source changes the voltage of the bypass pin in a controlled, linear manner. Ideally, the input and outputs track the voltage applied to the bypass pin. The gain of the internal amplifiers remains unity until the voltage on the bypass pin reaches 1/2 VDD. As soon as the voltage on the bypass pin is stable, the device becomes fully operational and the gain is set by the external voltage applied to the DC Vol/SD pin. Although the bypass pin current cannot be modified, changing the size of CB alters the device's turn-on time and the magnitude of "clicks and pops". Increasing the value of CB reduces the magnitude of turn-on pops. However, this presents a tradeoff: as the size of CB increases, the turn-on time increases. There is a linear relationship between the size of CB and the turn-on time. Shown below are some typical turn-on times for various values of CB: CB TON 0.01F 20ms 0.1F 200ms 0.22F 420ms 0.47F 840ms 1.0F 2sec In order eliminate "clicks and pops", all capacitors must be discharged before turn-on. Rapidly switching VDD may not allow the capacitors to fully discharge, which may cause "clicks and pops". In a single-ended configuration, the output coupling capacitor, COUT, is of particular concern. This capacitor discharges through an internal 20k resistor. Depending on the size of COUT, the time constant can be relatively large. To reduce transients in singleended mode, an external 1k - 5k resistor can be placed in parallel with the internal 20k resistor. The tradeoff for using this resistor is increased quiescent current. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 13 LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 www.ti.com RECOMMENDED PRINTED CIRCUIT BOARD LAYOUT Figure 31 through Figure 33 show the recommended two-layer PC board layout that is optimized for the SOIC-8 packaged LM4865 and associated external components. Figure 34 through Figure 38 show the recommended four-layer PC board layout for the micro SMD packaged LM4865. A four-layer board is recommended when using the micro SMD packaged LM4865: the two inner layers, one connected to the GND pin, the other to the VDD pin, provide heatsinking. Both layouts are designed for use with an external 5V supply, 8 speakers, and 32 headphones. The schematic for both recommended PC board layouts is Figure 3. Both circuit boards are easy to use. Apply a 5V supply voltage and ground to the board's VDD and GND pads, respectively. Connect a speaker with an 8 minimum impedance between the board's -OUT and +OUT pads. For headphone use, the layout has provisions for a headphone jack, J1. When a jack is connected as shown, inserting a headphone plug automatically switches off the external speaker. Figure 31. Recommended SOIC PC Board Layout: Component Side Silkscreen Figure 32. Recommended SOIC PC Board Layout: Component Side Layout 14 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 LM4865 www.ti.com SNAS035G - DECEMBER 1999 - REVISED MAY 2013 Figure 33. Recommended SOIC PC Board Layout: Bottom Side Layout Figure 34. Recommended micro SMD PC Board Layout: Component Side Silkscreen Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 15 LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 www.ti.com Figure 35. Recommended Micro SMD PC Board Layout: Component Side Layout Figure 36. Recommended Micro SMD PC Board Layout: Inner Layer VCC Layout 16 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 LM4865 www.ti.com SNAS035G - DECEMBER 1999 - REVISED MAY 2013 Figure 37. Recommended Micro SMD PC Board Layout: Inner Layer Ground Layout Figure 38. Recommended Micro SMD PC Board Layout: Bottom Side Layout Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 17 LM4865 SNAS035G - DECEMBER 1999 - REVISED MAY 2013 www.ti.com REVISION HISTORY Changes from Revision F (May 2013) to Revision G * 18 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 17 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM4865 PACKAGE OPTION ADDENDUM www.ti.com 26-Aug-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) LM4865M/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM48 65M LM4865MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 Z65 LM4865MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 Z65 LM4865MX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LM48 65M (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 26-Aug-2013 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM4865MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM4865MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LM4865MX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4865MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LM4865MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 LM4865MX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2015, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM4865M LM4865M/NOPB LM4865MM LM4865MM/NOPB LM4865MMX LM4865MMX/NOPB LM4865MX LM4865MX/NOPB