LM2660/LM2661 Switched Capacitor Voltage Converter General Description Features The LM2660/LM2661 CMOS charge-pump voltage converter inverts a positive voltage in the range of 1.5V to 5.5V to the corresponding negative voltage. The LM2660/LM2661 uses two low cost capacitors to provide 100 mA of output current without the cost, size, and EMI related to inductor based converters. With an operating current of only 120 A and operating efficiency greater than 90% at most loads, the LM2660/LM2661 provides ideal performance for battery powered systems. The LM2660/LM2661 may also be used as a positive voltage doubler. The oscillator frequency can be lowered by adding an external capacitor to the OSC pin. Also, the OSC pin may be used to drive the LM2660/LM2661 with an external clock. For LM2660, a frequency control (FC) pin selects the oscillator frequency of 10 kHz or 80 kHz. For LM2661, an external shutdown (SD) pin replaces the FC pin. The SD pin can be used to disable the device and reduce the quiescent current to 0.5 A. The oscillator frequency for the LM2661 is 80 kHz. n n n n n n Inverts or doubles input supply voltage Narrow SO-8 and Mini SO-8 Package 6.5 typical output resistance 88% typical conversion efficiency at 100 mA (LM2660) selectable oscillator frequency: 10 kHz/80 kHz (LM2661) low current shutdown mode Applications n n n n n n Laptop computers Cellular phones Medical instruments Operational amplifier power supplies Interface power supplies Handheld instruments Basic Application Circuits Voltage Inverter Positive Voltage Doubler 01291103 01291104 Splitting VIN in Half 01291126 (c) 2004 National Semiconductor Corporation DS012911 www.national.com LM2660/LM2661 Switched Capacitor Voltage Converter September 1999 LM2660/LM2661 Absolute Maximum Ratings (Note 1) Package If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Power Dissipation Supply Voltage (V+ to GND, or GND to OUT) TJ Max (Note 3) LV (TA = 25C) (Note 3) 6V (OUT - 0.3V) to (GND + 3V) FC, OSC JA (Note 3) The least negative of (OUT - 0.3V) or (V+ - 6V) to (V+ + 0.3V) V+ and OUT Continuous Output Current Output Short-Circuit Duration to GND (Note 2) M MM 735 mW 500 mW 150C 150C 170C/W 250C/W Operating Junction Temperature 120 mA Range -40C to +85C Storage Temperature Range 1 sec. -65C to +150C Lead Temperature 300C (Soldering, 10 seconds) ESD Rating 2 kV Electrical Characteristics Limits in standard typeface are for TJ = 25C, and limits in boldface type apply over the full operating temperature range. Unless otherwise specified: V+ = 5V, FC = Open, C1 = C2 = 150 F. (Note 4) Symbol V+ IQ Parameter Supply Voltage Supply Current Condition RL = 1k No Load Min Inverter, LV = Open 3.5 5.5 1.5 5.5 Doubler, LV = OUT 2.5 5.5 FC = V+ (LM2660) or SD = Ground (LM2661) ISD Shutdown Supply Current (LM2661) VSD IL ROUT Shutdown Pin Input Voltage Shutdown Mode (LM2661) Normal Operation Output Current TA +85C, OUT -4V 100 TA > +85C, OUT -3.8V 100 Output Resistance (Note 6) 2.0 0.12 0.5 1 3 0.5 2 (Note 5) 0.3 TA +85C IL = 100 mA fSW IOSC Oscillator Frequency (Note 7) Switching Frequency (Note 8) OSC Input Current OSC = Open OSC = Open 6.5 FC = Open 5 10 FC = V+ 40 80 FC = Open 2.5 5 FC = V+ 20 40 2 16 FC = V+ PEFF Power Efficiency RL (1k) between V+ and OUT 96 RL (500) between GND and OUT 92 IL = 100 mA to GND VOEFF Voltage Conversion Efficiency No Load 10 12 FC = Open Units V mA A V mA TA > +85C fOSC Max Inverter, LV = GND FC = Open (LM2660) LV = Open Typ kHz kHz A 98 96 % 88 99 99.96 % Note 1: Absolute maximum ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device beyond its rated operating conditions. Note 2: OUT may be shorted to GND for one second without damage. However, shorting OUT to V+ may damage the device and should be avoided. Also, for temperatures above 85C, OUT must not be shorted to GND or V+, or device may be damaged. Note 3: The maximum allowable power dissipation is calculated by using PDMax = (TJMax - TA)/JA, where TJMax is the maximum junction temperature, TA is the ambient temperature, and JA is the junction-to-ambient thermal resistance of the specified package. Note 4: In the test circuit, capacitors C1 and C2 are 0.2 maximum ESR capacitors. Capacitors with higher ESR will increase output resistance, reduce output voltage and efficiency. Note 5: In doubling mode, when Vout > 5V, minimum input high for shutdown equals Vout - 3V. Note 6: Specified output resistance includes internal switch resistance and capacitor ESR. Note 7: For LM2661, the oscillator frequency is 80 kHz. Note 8: The output switches operate at one half of the oscillator frequency, fOSC = 2fSW. www.national.com 2 LM2660/LM2661 Test Circuits 01291105 01291106 FIGURE 1. LM2660 and LM2661 Test Circuits Typical Performance Characteristics (Circuit of Figure 1) Supply Current vs Supply Voltage Output Source Resistance vs Supply Voltage Supply Current vs Oscillator Frequency 01291107 Output Source Resistance vs Temperature 01291108 Efficiency vs Load Current Output Voltage Drop vs Load Current 01291111 01291110 3 01291109 01291112 www.national.com LM2660/LM2661 Typical Performance Characteristics (Circuit of Figure 1) Efficiency vs Oscillator Frequency 01291114 Oscillator Frequency vs Supply Voltage (FC = V+) Oscillator Frequency vs Supply Voltage (FC = Open) 01291116 01291115 Oscillator Frequency vs Temperature (FC = V+) 01291117 01291118 Shutdown Supply Current vs Temperature (LM2661 Only) Oscillator Frequency vs Temperature (FC = Open) 01291119 www.national.com Oscillator Frequency vs External Capacitance Output Voltage vs Oscillator Frequency 01291113 (Continued) 01291120 4 LM2660/LM2661 Connection Diagrams 8-Lead SO (M) or Mini SO (MM) 01291101 01291102 Top View Order Number LM2660M, LM2661M, LM2660MM or LM2661MM See NS Package Number M08A and MUA08A Ordering Information Order Number LM2660M Package Number M08A Package Marking Datecode Supplied As Rail (95 units/rail) LM26 60M LM2660MX M08A Datecode Tape and Reel (2500 units/rail) LM26 60M LM2660MM MUA08A S01A (Note 9) Tape and Reel (250 units/rail) LM2660MMX MUA08A S01A (Note 9) Tape and Reel (3500 units/rail) LM2661M M08A Datecode Rail (95 units/rail) LM26 61M LM2661MX M08A Datecode Tape and Reel (2500 units/rail) LM26 61M LM2661MM MUA08A S02A (Note 9) Tape and Reel (250 units/rail) LM2661MMX MUA08A S02A (Note 9) Tape and Reel (3500 units/rail) Note 9: The first letter "S" identifies the part as a switched capacitor converter. The next two numbers are the device number: "01" for a LM2660 device, and "02" for a LM2661 device. The fourth letter "A" indicates the grade. Only one grade is available. Larger quantity reels are available upon request. 5 www.national.com LM2660/LM2661 Pin Description Pin Name Function Voltage Inverter 1 FC Voltage Doubler Frequency control for internal oscillator: (LM2660) Same as inverter. FC = open, fOSC = 10 kHz (typ); FC = V+, fOSC = 80 kHz (typ); FC has no effect when OSC pin is driven externally. 1 SD (LM2661) Shutdown control pin, tie this pin to the ground in normal operation, and to V+ for shutdown. Same as inverter. 2 CAP+ Connect this pin to the positive terminal of charge-pump capacitor. Same as inverter. 3 GND Power supply ground input. Power supply positive voltage input. 4 CAP- Connect this pin to the negative terminal of charge-pump capacitor. Same as inverter. 5 OUT Negative voltage output. Power supply ground input. 6 LV Low-voltage operation input. Tie LV to GND when input voltage is less than 3.5V. Above 3.5V, LV can be connected to GND or left open. When driving OSC with an external clock, LV must be connected to GND. LV must be tied to OUT. 7 OSC Oscillator control input. OSC is connected to an internal 15 pF capacitor. An external capacitor can be connected to slow the oscillator. Also, an external clock can be used to drive OSC. Same as inverter except that OSC cannot be driven by an external clock. 8 V+ Power supply positive voltage input. Positive voltage output. Circuit Description Application Information The LM2660/LM2661 contains four large CMOS switches which are switched in a sequence to invert the input supply voltage. Energy transfer and storage are provided by external capacitors. Figure 2 illustrates the voltage conversion scheme. When S1 and S3 are closed, C1 charges to the supply voltage V+. During this time interval switches S2 and S4 are open. In the second time interval, S1 and S3 are open and S2 and S4 are closed, C1 is charging C2. After a number of cycles, the voltage across C2 will be pumped to V+. Since the anode of C2 is connected to ground, the output at the cathode of C2 equals -(V+) assuming no load on C2, no loss in the switches, and no ESR in the capacitors. In reality, the charge transfer efficiency depends on the switching frequency, the on-resistance of the switches, and the ESR of the capacitors. SIMPLE NEGATIVE VOLTAGE CONVERTER The main application of LM2660/LM2661 is to generate a negative supply voltage. The voltage inverter circuit uses only two external capacitors as shown in the Basic Application Circuits. The range of the input supply voltage is 1.5V to 5.5V. For a supply voltage less than 3.5V, the LV pin must be connected to ground to bypass the internal regulator circuitry. This gives the best performance in low voltage applications. If the supply voltage is greater than 3.5V, LV may be connected to ground or left open. The choice of leaving LV open simplifies the direct substitution of the LM2660/ LM2661 for the LMC7660 Switched Capacitor Voltage Converter. The output characteristics of this circuit can be approximated by an ideal voltage source in series with a resistor. The voltage source equals -(V+). The output resistance Rout is a function of the ON resistance of the internal MOS switches, the oscillator frequency, and the capacitance and ESR of C1 and C2. A good approximation is: where RSW is the sum of the ON resistance of the internal MOS switches shown in Figure 2. High value, low ESR capacitors will reduce the output resistance. Instead of increasing the capacitance, the oscillator frequency can be increased to reduce the 2/(fosc x C1) term. Once this term is trivial compared with RSW and ESRs, further increasing in oscillator frequency and capacitance will become ineffective. 01291121 FIGURE 2. Voltage Inverting Principle www.national.com 6 TABLE 1. LM2660 Oscillator Frequency Selection (Continued) FC The peak-to-peak output voltage ripple is determined by the oscillator frequency, and the capacitance and ESR of the output capacitor C2: OSC Open 10 kHz V+ Open 80 kHz Open or V+ External Capacitor See Typical Performance Characteristics External Clock External Clock (inverter mode only) Frequency N/A Again, using a low ESR capacitor will result in lower ripple. Oscillator Open POSITIVE VOLTAGE DOUBLER The LM2660/LM2661 can operate as a positive voltage doubler (as shown in the Basic Application Circuits). The doubling function is achieved by reversing some of the connections to the device. The input voltage is applied to the GND pin with an allowable voltage from 2.5V to 5.5V. The V+ pin is used as the output. The LV pin and OUT pin must be connected to ground. The OSC pin can not be driven by an external clock in this operation mode. The unloaded output voltage is twice of the input voltage and is not reduced by the diode D1's forward drop. The Schottky diode D1 is only needed for start-up. The internal oscillator circuit uses the V+ pin and the LV pin (connected to ground in the voltage doubler circuit) as its power rails. Voltage across V+ and LV must be larger than 1.5V to insure the operation of the oscillator. During start-up, D1 is used to charge up the voltage at V+ pin to start the oscillator; also, it protects the device from turning-on its own parasitic diode and potentially latching-up. Therefore, the Schottky diode D1 should have enough current carrying capability to charge the output capacitor at start-up, as well as a low forward voltage to prevent the internal parasitic diode from turning-on. A Schottky diode like 1N5817 can be used for most applications. If the input voltage ramp is less than 10V/ms, a smaller Schottky diode like MBR0520LT1 can be used to reduce the circuit size. TABLE 2. LM2661 Oscillator Frequency Selection OSC Oscillator Open 80 kHz External Capacitor See Typical Performance Characteristics External Clock External Clock Frequency (inverter mode only) SHUTDOWN MODE For the LM2661, a shutdown (SD) pin is available to disable the device and reduce the quiescent current to 0.5 A. Applying a voltage greater than 2V to the SD pin will bring the device into shutdown mode. While in normal operating mode, the SD pin is connected to ground. CAPACITOR SELECTION As discussed in the Simple Negative Voltage Converter section, the output resistance and ripple voltage are dependent on the capacitance and ESR values of the external capacitors. The output voltage drop is the load current times the output resistance, and the power efficiency is SPLIT V+ IN HALF Another interesting application shown in the Basic Application Circuits is using the LM2660/LM2661 as a precision voltage divider. Since the off-voltage across each switch equals VIN/2, the input voltage can be raised to +11V. Where IQ(V+) is the quiescent power loss of the IC device, and IL2ROUT is the conversion loss associated with the switch on-resistance, the two external capacitors and their ESRs. Since the switching current charging and discharging C1 is approximately twice as the output current, the effect of the ESR of the pumping capacitor C1 is multiplied by four in the output resistance. The output capacitor C2 is charging and discharging at a current approximately equal to the output current, therefore, its ESR only counts once in the output resistance. However, the ESR of C2 directly affects the output voltage ripple. Therefore, low ESR capacitors (Table 3) are recommended for both capacitors to maximize efficiency, reduce the output voltage drop and voltage ripple. For convenience, C1 and C2 are usually chosen to be the same. The output resistance varies with the oscillator frequency and the capacitors. In Figure 3, the output resistance vs. oscillator frequency curves are drawn for three different tantalum capacitors. At very low frequency range, capacitance plays the most important role in determining the output resistance. Once the frequency is increased to some point (such as 20 kHz for the 150 F capacitors), the output resistance is dominated by the ON resistance of the internal switches and the ESRs of the external capacitors. A low CHANGING OSCILLATOR FREQUENCY For the LM2660, the internal oscillator frequency can be selected using the Frequency Control (FC) pin. When FC is open, the oscillator frequency is 10 kHz; when FC is connected to V+, the frequency increases to 80 kHz. A higher oscillator frequency allows smaller capacitors to be used for equivalent output resistance and ripple, but increases the typical supply current from 0.12 mA to 1 mA. The oscillator frequency can be lowered by adding an external capacitor between OSC and GND. (See Typical Performance Characteristics.) Also, in the inverter mode, an external clock that swings within 100 mV of V+ and GND can be used to drive OSC. Any CMOS logic gate is suitable for driving OSC. LV must be grounded when driving OSC. The maximum external clock frequency is limited to 150 kHz. The switching frequency of the converter (also called the charge pump frequency) is half of the oscillator frequency. Note: OSC cannot be driven by an external clock in the voltage-doubling mode. 7 www.national.com LM2660/LM2661 Application Information LM2660/LM2661 Application Information pared with a bigger size capacitor of the same type. For lower ESR, use ceramic capacitors. (Continued) value, smaller size capacitor usually has a higher ESR com- 01291132 FIGURE 3. Output Source Resistance vs Oscillator Frequency TABLE 3. Low ESR Capacitor Manufacturers Phone FAX Nichicon Corp. Manufacturer (708)-843-7500 (708)-843-2798 PL, PF series, through-hole aluminum electrolytic Capacitor Type AVX Corp. (803)-448-9411 (803)-448-1943 TPS series, surface-mount tantalum Sprague (207)-324-4140 (207)-324-7223 593D, 594D, 595D series, surface-mount tantalum Sanyo (619)-661-6835 (619)-661-1055 OS-CON series, through-hole aluminum electrolytic Other Applications PARALLELING DEVICES Any number of LM2660s (or LM2661s) can be paralleled to reduce the output resistance. Each device must have its own pumping capacitor C1, while only one output capacitor Cout is needed as shown in Figure 4. The composite output resistance is: 01291122 FIGURE 4. Lowering Output Resistance by Paralleling Devices www.national.com 8 A three-stage cascade circuit shown in Figure 6 generates -3Vin, from Vin. Cascading is also possible when devices are operating in doubling mode. In Figure 7, two devices are cascaded to generate 3Vin. (Continued) CASCADING DEVICES Cascading the LM2660s (or LM2661s) is an easy way to produce a greater negative voltage (as shown in Figure 5). If n is the integer representing the number of devices cascaded, the unloaded output voltage Vout is (-nVin). The effective output resistance is equal to the weighted sum of each individual device: An example of using the circuit in Figure 6 or Figure 7 is generating +15V or -15V from a +5V input. Note that, the number of n is practically limited since the increasing of n significantly reduces the efficiency and increases the output resistance and output voltage ripple. 01291123 FIGURE 5. Increasing Output Voltage by Cascading Devices 01291124 FIGURE 6. Generating -3Vin from +Vin 9 www.national.com LM2660/LM2661 Other Applications LM2660/LM2661 Other Applications (Continued) 01291125 FIGURE 7. Generating +3Vin from +Vin The error flag on pin 5 of the LP2951 goes low when the regulated output at pin 4 drops by about 5%. The LP2951 can be shutdown by taking pin 3 high. REGULATING Vout It is possible to regulate the output of the LM2660/LM2661 by use of a low dropout regulator (such as LP2951). The whole converter is depicted in Figure 8. This converter can give a regulated output from -1.5V to -5.5V by choosing the proper resistor ratio: where, Vref = 1.235V 01291127 FIGURE 8. Combining LM2660/LM2661 with LP2951 to Make a Negative Adjustable Regulator Also, as shown in Figure 9 by operating LM2660/LM2661 in voltage doubling mode and adding a linear regulator (such as LP2981) at the output, we can get +5V output from an input as low as +3V. www.national.com 10 LM2660/LM2661 Other Applications (Continued) 01291128 FIGURE 9. Generating +5V from +3V Input Voltage 11 www.national.com LM2660/LM2661 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead SO (M) Order Number LM2660M or LM2661M NS Package Number M08A 8-Lead Mini SO (MM) Order Number LM2660MM or LM2661MM NS Package Number MUA08A www.national.com 12 LM2660/LM2661 Switched Capacitor Voltage Converter Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560