a FEATURES Single Chip Construction On-Board Output Amplifier Low Power Dissipation: 300 mW Monotonicity Guaranteed over Temperature Guaranteed for Operation with 12 V Supplies Improved Replacement for Standard DAC80, DAC800 Hl-5680 High Stability, High Current Output Buried Zener Reference Laser Trimmed to High Accuracy 1/2 LSB Max Nonlinearity Low Cost Plastic Packaging Complete Low Cost 12-Bit D/A Converters ADDAC80/ADDAC85/ADDAC87 FUNCTIONAL BLOCK DIAGRAM (MSB) BIT 1 1 REF CONTROL CIRCUIT BIT 2 2 BIT 3 3 BIT 4 4 BIT 5 5 BIT 6 6 BIT 7 7 BIT 8 8 12-BIT RESISTOR LADDER NETWORK AND CURRENT SWITCHES BIT 9 9 5k 24 VREF OUT 23 GAIN ADJUST 22 +VS 21 COMMON 20 SUMMING JUNCTION 19 20V RANGE 18 10V RANGE 17 BIPOLAR OFFSET 16 REF INPUT 5k 6.3k - BIT 10 10 15 VOUT 14 -VS 13 NC/+VL* + BIT 11 11 ADDAC80 (LSB) BIT 12 12 *NC = CBI VERSIONS 5V - CCD VERSIONS PRODUCT DESCRIPTION The ADDAC80 Series is a family of low cost 12-bit digital-toanalog converters with both a high stability voltage reference and output amplifier combined on a single monolithic chip. The ADDAC80 Series is recommended for all low cost 12-bit D/A converter applications where reliability and cost are of paramount importance. Advanced circuit design and precision processing techniques result in significant performance advantages over conventional DAC80 devices. Innovative circuit design reduces the total power consumption to 300 mW, which not only improves reliability, but also improves long term stability. The ADDAC80 incorporates a fully differential, nonsaturating precision current switching cell structure which provides greatly increased immunity to supply voltage variation. This same structure also reduces nonlinearities due to thermal transients as the various bits are switched; nearly all critical components operate at constant power dissipation. High stability, SiCr thin film resistors are trimmed with a fine resolution laser, resulting in lower differential nonlinearity errors. A low noise, high stability, subsurface Zener diode is used to produce a reference voltage with excellent long term stability, high external current capability and temperature drift characteristics which challenge the best discrete Zener references. The ADDAC80 Series is available in three performance grades and three package types. The ADDAC80 is specified for use over the 0C to 70C temperature range and is available in both plastic and ceramic DIP packages. The ADDAC85 and ADDAC87 are available in hermetically sealed ceramic packages and are specified for the -25C to +85C and -55C to +125C temperature ranges. (MSB) BIT 1 1 REF CONTROL CIRCUIT BIT 2 2 BIT 3 3 BIT 4 4 BIT 5 5 BIT 6 6 BIT 7 7 BIT 8 8 12-BIT RESISTOR LADDER NETWORK AND CURRENT SWITCHES BIT 9 9 2k 5k 5k 24 VREF OUT 23 GAIN ADJUST 22 +VS 21 COMMON 20 SCALING NETWORK 19 SCALING NETWORK 18 SCALING NETWORK 17 BIPOLAR OFFSET 16 REF INPUT 6.3k BIT 10 10 15 IOUT BIT 11 11 14 -VS 13 NC/+VL* (LSB) BIT 12 12 *NC = CBI VERSIONS 5V - CCD VERSIONS PRODUCT HIGHLIGHTS 1. The ADDAC80 series of D/A converters directly replaces all other devices of this type with significant increases in performance. 2. Single chip construction and low power consumption provides the optimum choice for applications where low cost and high reliability are major considerations. 3. The high speed output amplifier has been designed to settle within 1/2 LSB for a 10 V full scale transition in 2.0 s, when properly compensated. 4. The precision buried Zener reference can supply up to 2.5 mA for use elsewhere in the application. 5. The low TC binary ladder guarantees that all units are monotonic over the specified temperature range. 6. System performance upgrading is possible without redesign. REV. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) Analog Devices, Inc., 2002 (TA = 25C, rated power supplies unless otherwise noted.) ADDAC80/ADDAC85/ADDAC87-SPECIFICATIONS Model Min TECHNOLOGY DIGITAL INPUT Binary-CBI BCD-CCD Logic Levels (TTL Compatible) VIH (Logic "1") VIL (Logic "0") IIH (VIH = 5.5 V) IIL (VIL = 0.8 V) TRANSFER CHARACTERISTICS ACCURACY Linearity Error @ 25C CBI CCD TA @ TMIN to TMAX Differential Linearity Error @ 25C CBI CCD TA @ TMIN to TMAX Gain Error2 Offset Error2 Temperature Range for Guaranteed Monotonicity DRIFT (TMIN to TMAX) Total Bipolar Drift, max (includes gain, offset, and linearity drifts) Total Error (TMIN to TMAX)4 Unipolar Bipolar Gain Including Internal Reference Gain Excluding Internal Reference Unipolar Offset Bipolar Offset CONVERSION SPEED Voltage Model (V)5 Settling Time to 0.01% of FSR for FSR Change (2 k500 pF load) with 10 k Feedback with 5 k Feedback For LSB Change Slew Rate ADDAC80 Typ Max Monolithic 2.0 0 2.0 0 0 1/4 0.1 0.05 -25 1/2 12 Bits Digits 5.5 0.8 250 100 V V A A 1/2 LSB1 LSB LSB 3/4 3/4 1 0.2 0.1 +85 20 0.1 0.05 -55 20 1 0.2 0.1 LSB LSB LSB %FSR3 %FSR3 +125 C 30 ppm of FSR/C 0.08 0.06 15 4 1 5 0.15 0.10 30 7 3 10 0.12 0.08 0.2 0.12 20 10 3 10 0.18 0.14 0.3 0.24 20 10 3 10 % of FSR % of FSR ppm of FSR/C ppm of FSR/C ppm of FSR/C ppm of FSR/C 3 2 1 4 3 3 2 1 4 3 3 2 1 4 3 s s s V/s 10 10 2.5, 5, 10, +5, 10 10 2.5, 5, 10, +5, 10 5 2.5, 5, 10, +5, 10 2.5 20 2.5 10 V V V V mA mA V mA ppm of VR/C 0.002 0.002 0.002 0.002 % of FSR/%VS % of FSR/%VS 5 0.05 6.23 1/2 3/4 3/4 0.3 0.15 +70 2.0 0 1/2 1/2 Unit Monolithic 5.5 0.8 250 100 3/4 0.1 0.05 ADDAC87 Typ Max 12 1/2 1/4 Min Monolithic 5.5 0.8 250 100 6.3 1.5 10 POWER SUPPLY SENSITIVITY 15 V 10%, 5 V supply when applicable 12 V 5% POWER SUPPLY REQUIREMENTS Rated Voltages Range Analog Supplies Logic Supplies Supply Drain +12 V, +15 V -12 V, -15 V ADDAC85 Typ Max 12 ANALOG OUTPUT Voltage Models Ranges-CBI -CCD Output Current Output Impedance (dc) Short Circuit Current Internal Reference Voltage (VR) Output Impedance Max External Current6 Tempco of Drift Min 5 0.05 40 6.37 6.23 2.5 20 6.3 1.5 10 0.002 0.002 15 11.47 6.23 15 16.5 5 14 0.05 40 6.37 11.47 10 20 -2- 40 6.37 15 16.5 5 14 6.3 1.5 10 20 11.47 5 14 V 16.5 V V 10 20 mA mA REV. B ADDAC80/ADDAC85/ADDAC87 Model Min TEMPERATURE RANGE Specifications Operating Storage 0 -25 -25 ADDAC80 Typ Max +70 +85 +125 Min ADDAC85 Typ Max -25 -55 -65 +85 +125 +150 Min ADDAC87 Typ Max -55 -55 -65 +125 +125 +150 Unit C C C NOTES 1 Least Significant Bit. 2 Adjustable to zero with external trim potentiometer. 3 FSR means "Full Scale Range" and is 20 V for the 10 V range and 10 V for the 5 V range. 4 Gain and offset errors adjusted to zero at 25C. 5 CF = 0, see Figure 3a. 6 Maximum with no degradation of specification, must be a constant load. 7 A minimum of 12.3 V is required for a 10 V full scale output and 11.4 V is required for all other voltage ranges. Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min and max specifications are guaranteed, although only those shown in boldface are tested on all production units. Specifications subject to change without notice. Model Min TECHNOLOGY DIGITAL INPUT Binary-CBI BCD-CCD Logic Levels (TTL Compatible) VIH (Logic "1") VIL (Logic "0") IIH (VIH = 5.5 V) IIL (VIL = 0.8 V) TRANSFER CHARACTERISTICS ACCURACY Linearity Error @ 25C CBI CCD TA @ TMIN to TMAX Differential Linearity Error @ 25C CBI CCD TA @ TMIN to TMAX Gain Error2 Offset Error2 Temperature Range for Guaranteed Monotonicity DRIFT (TMIN to TMAX) Total Bipolar Drift, max (includes gain, offset, and linearity drifts) Total Error (TMIN to TMAX)4 Unipolar Bipolar Gain Including Internal Reference Excluding Internal Reference Unipolar Offset Bipolar Offset CONVERSION SPEED Voltage Model (V)5 Settling Time to 0.01% of FSR for FSR Change (2 k500 pF load) with 10 k Feedback with 5 k Feedback For LSB Change Slew Rate Current Model (I) Settling time to 0.01% of FSR for FSR Change 10 to 100 Load for 1 k REV. B ADDAC80 Typ Max Min Hybrid ADDAC85 Typ Max Hybrid 12 3 2.0 0 5.5 0.8 2.0 0 1/2 1/4 1/2 1/2 1/4 3/4 1/2 1 0.3 0.15 0 10 5.5 0.8 +70 1/4 1/2 1/2 0.1 0.05 0 Unit Hybrid 2.0 0 250 -100 1/4 1/8 1/4 ADDAC87 Typ Max 12 3 250 -100 0.1 0.05 Min 12 3 Bits Digits 5.5 0.8 V V A A 1/2 1/4 1/2 LSB1 LSB LSB 1 LSB LSB LSB %FSR3 %FSR3 +85 C 250 -100 1/2 1/4 1/2 1/2 1/2 1/2 1 +70 0.1 0.05 -25 20 ppm of FSR/C 0.08 0.06 0.15 0.10 % of FSR % of FSR 15 5 1 5 30 7 3 10 1 20 10 10 1 20 10 10 ppm of FSR/C ppm of FSR/C ppm of FSR/C ppm of FSR/C 5 3 1.5 15 5 3 1.5 20 5 3 1.5 20 s s s V/s 300 1 300 1 300 1 ns s -3- ADDAC80/ADDAC85/ADDAC87-SPECIFICATIONS (continued) Model Min ANALOG OUTPUT Voltage Models Ranges-CBI Ranges-CCD Output Current Output Impedance (dc) Short Circuit Duration Current Models Ranges-Unipolar Ranges-Bipolar Output Impedance Bipolar Unipolar Compliance Internal Reference Voltage (VR) Output Impedance Max External Current6 Tempco of Drift 5 TEMPERATURE RANGE Specifications Operating Storage 2.5, 5, 10, +5, +10 10 0.05 Indefinite to Common 6.17 POWER SUPPLY SENSITIVITY 15 V 10%, 5 V Supply When Applicable POWER SUPPLY REQUIREMENTS Rated Voltages Range Analog Supplies Logic Supplies Supply Drain7 +15 V -15 V +5 V8 ADDAC80 Typ Max 5 ADDAC85 Typ Max 2.5, 5, 10, +5, +10 +10 0.05 Indefinite to Common Min 5 ADDAC87 Typ Max 2.5, 5, 10, +5, +10 +10 0.05 Indefinite to Common Unit V V mA -2.0 1.0 -2.0 1.0 -2.0 1.0 mA mA 3.2 6.6 -1.5, +10 6.3 6.43 1.5 2.5 10 20 3.2 6.6 -2.5, +10 6.3 6.43 1.5 2.5 10 20 3.2 6.6 -2.5, +10 6.3 6.43 1.5 2.5 10 20 k k V V mA ppm of VR/C 6.17 6.17 0.002 0.002 0.002 % of FSR/%VS 15, +5 15, +5 15, +5 V 14 4.5 16 16 10 20 8 0 -25 -55 Min 14.5 4.5 20 35 20 +70 +85 +130 15.5 15.5 15 25 15 0 -25 -65 14.5 4.5 20 30 20 +70 +85 +150 15 25 15 -25 -55 -65 15.5 15.5 V V 20 30 20 mA mA mA +85 +125 +150 C C C NOTES 1 Least Significant Bit. 2 Adjustable to zero with external trim potentiometer. 3 FSR means "Full Scale Range" and is 20 V for the 10 V range and 10 V for the 5 V range. 4 Gain and offset errors adjusted to zero at 25C. 5 CF = 0, see Figure 3a. 6 Maximum with no degradation of specification, must be a constant load. 7 Including 5 mA load. 8 5 V supply required only for CCD versions. Specifications subject to change without notice. -4- REV. B ADDAC80/ADDAC85/ADDAC87 Model ADDAC85LD Min Typ Max TECHNOLOGY DIGITAL INPUT Binary-CBI BCD-CCD Logic Levels (TTL Compatible) VIH (Logic "1") VIL (Logic "0") IIH (VIH = 5.5 V) IIL (VIL = 0.8 V) TRANSFER CHARACTERISTICS ACCURACY Linearity Error @ 25C CBI CCD TA @ TMIN to TMAX Differential Linearity Error @ 25C CBI CCD TA @ TMIN to TMAX Gain Error2 Offset Error2 Temperature Range for Guaranteed Monotonicity DRIFT (TMIN to TMAX) Total Bipolar Drift, max (includes gain, offset, and linearity drifts) Total Error (TMIN to TMAX)4 Unipolar Bipolar Gain Including Internal Reference Excluding Internal Reference Unipolar Offset Bipolar Offset Hybrid 2.0 0 REV. B 2.0 0 5.5 0.8 1/2 1/2 3/4 +85 -55 1 2 V V A A 1/2 3/4 LSB1 LSB LSB 1 0.2 0.1 LSB LSB LSB %FSR3 %FSR3 +125 C 15 30 ppm of FSR/C 0.13 0.12 0.30 0.24 % of FSR % of FSR 10 5 1 5 25 10 3 10 ppm of FSR/C ppm of FSR/C ppm of FSR/C ppm of FSR/C 1/4 1 0.1 0.05 -55 20 5 5.5 0.8 1/2 +125 10 Bits Digits 2.0 0 1/2 0.1 0.05 12 250 -100 1/2 1 10 5 3 1.5 20 5 3 1.5 20 5 3 1.5 20 s s s V/s 300 1 300 1 300 1 ns s 2.5, 5, 10, +5, +10 2.5, 5, 10, +5, +10 2.5, 5, 10, +5, +10 5 5 5 0.05 Indefinite to Common 0.05 Indefinite to Common 0.05 Indefinite to Common 6.17 Unit Hybrid 250 -100 1/2 -25 ADDAC87 Typ Max 12 250 -100 ANALOG OUTPUT Voltage Models Ranges-CBI POWER SUPPLY SENSITIVITY 15 V 10%, 5 V supply when applicable 5.5 0.8 0.1 0.05 Min Hybrid 12 CONVERSION SPEED Voltage Model (V)5 Settling Time to 0.01% of FSR for FSR change (2 k500 pF load) with 10 k Feedback with 5 k Feedback For LSB Change Slew Rate Current Model (I) Settling Time to 0.01% of FSR for FSR Change 10 to 100 Load for 1 k Ranges-CCD Output Current Output Impedance (dc) Short Circuit Duration Current Models Ranges-Unipolar Ranges-Bipolar Output Impedance Bipolar Unipolar Compliance Internal Reference Voltage (VR) Output Impedance Max External Current6 Tempco of Drift ADDAC85MIL Min Typ Max -2.0 1.0 -2.0 1.0 3.2 6.6 -2.5, +10 6.3 6.43 1.5 2.5 10 20 3.2 6.6 -2.5, +10 6.3 6.43 1.5 2.5 10 20 6.17 0.002 0.002 -5- 2.5 5.0 6.17 V V mA -2.0 1.0 mA mA 3.2 4.1 6.6 8.2 -1.5, +10 6.3 6.43 1.5 2.5 5 10 k k V V mA ppm of VR/C 0.002 0.003 % of FSR/%VS ADDAC80/ADDAC85/ADDAC87-SPECIFICATIONS (continued) ADDAC85LD Min Typ Max Model POWER SUPPLY REQUIREMENTS Rated Voltages Range Analog Supplies Logic Supplies Supply Drain7 +15 V -15 V +5 V8 ADDAC85MIL Min Typ Max 15, 5 14.5 +4.5 TEMPERATURE RANGE Specification Operating Storage -25 -55 -55 ADDAC87 Typ Max 15, 5 15.5 15.5 15 25 15 Min 14.5 +4.5 20 30 20 +85 +125 +125 15, 5 15.5 +15.5 15 25 15 -55 -55 -55 Unit 13.5 +4.5 20 30 20 +125 +125 +125 V 10 20 10 -55 -55 -65 16.5 16.5 V V 20 35 20 mA mA mA +125 +125 +150 C C C NOTES 1 Least Significant Bit. 2 Adjustable to zero with external trim potentiometer. 3 FSR means "Full-Scale Range" and is 20 V for the 10 V range and 10 V for the 5 V range. 4 Gain and offset errors adjusted to zero at 25C. 5 CF = 0, see Figure 3a. 6 Maximum with no degradation of specification, must be a constant load. 7 Including 5 mA load. 8 5 V supply required only for CCD versions. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS +VS to Power Ground . . . . . . . . . . . . . . . . . . . . 0 V to +18 V -VS to Power Ground . . . . . . . . . . . . . . . . . . . . 0 V to -18 V Digital Inputs (Pins 1 to 12) to Power Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1.0 V to +7 V Ref In to Reference Ground . . . . . . . . . . . . . . . . . . . . . 12 V Bipolar Offset to Reference Ground . . . . . . . . . . . . . . 12 V 10 V Span R to Reference Ground . . . . . . . . . . . . . . . 12 V 20 V Span R to Reference Ground . . . . . . . . . . . . . . . 24 V Ref Out . . . . . . . . . Indefinite Short to Power Ground or +VS (MSB) BIT 1 1 REF CONTROL CIRCUIT BIT 2 2 BIT 3 3 BIT 4 4 BIT 5 5 BIT 6 6 BIT 7 7 BIT 8 8 BIT 9 9 BIT 10 10 12-BIT RESISTOR LADDER NETWORK AND CURRENT SWITCHES 5k VREF OUT 23 GAIN ADJUST BIT 2 2 22 +VS BIT 3 3 21 COMMON BIT 4 4 20 SUMMING JUNCTION BIT 5 5 19 20V RANGE BIT 6 6 18 10V RANGE BIT 7 7 17 BIPOLAR OFFSET BIT 8 8 16 REF INPUT BIT 9 9 15 VOUT BIT 10 10 15 IOUT 14 -VS BIT 11 11 14 -VS 13 NC/+VL* 13 NC/+VL* 5k 6.3k - + BIT 11 11 (LSB) BIT 12 12 24 ADDAC80 (MSB) BIT 1 1 REF CONTROL CIRCUIT 12-BIT RESISTOR LADDER NETWORK AND CURRENT SWITCHES 2k 5k 5k VREF OUT 23 GAIN ADJUST 22 +VS 21 COMMON 20 SCALING NETWORK 19 SCALING NETWORK 18 SCALING NETWORK 17 BIPOLAR OFFSET 16 REF INPUT 6.3k (LSB) BIT 12 12 *NC = CBI VERSIONS 5V - CCD VERSIONS 24 *NC = CBI VERSIONS 5V - CCD VERSIONS Figure 1. Voltage Model Function Diagram and Pin Configuration Figure 2. Current Model Functional Diagram and Pin Configuration -6- REV. B ADDAC80/ADDAC85/ADDAC87 ORDERING GUIDE Model Input Code Output Mode Technology Temperature Range Linearity Error Package Option1 ADDAC80N-CBI-V ADDAC80D-CBI-V ADDAC85D-CBI-V ADDAC87D-CBI-V ADDAC80-CBI-V ADDAC80-CBI-I ADDAC80-CCD-V ADDAC80-CCD-I ADDAC80Z-CBI-V2 ADDAC80Z-CBI-I2 ADDAC80Z-CCD-V2 ADDAC80Z-CCD-I2 ADDAC85C-CBI-V3 ADDAC85C-CBI-I ADDAC85-CBI-V3 ADDAC85-CBI-I3 ADDAC85LD-CBI-V3 ADDAC85LD-CBI-I3 ADDAC85MIL-CBI-V3 ADDAC85MIL-CBI-I3 ADDAC85C-CCD-V3 ADDAC85C-CCD-I3 ADDAC85-CCD-V3 ADDAC85-CCD-I3 ADDAC85MILCBII8 ADDAC85MILCBIV8 ADDAC87-CBI-V3 ADDAC87-CBI-I3 ADDAC87-CBII883 ADDAC87-CBIV883 Binary Binary Binary Binary Binary Binary Binary Coded Decimal Binary Coded Decimal Binary Binary Binary Coded Decimal Binary Coded Decimal Binary Binary Binary Binary Binary Binary Binary Binary Binary Coded Decimal Binary Coded Decimal Binary Coded Decimal Binary Coded Decimal Binary Binary Binary Binary Binary Binary Voltage Voltage Voltage Voltage Voltage Current Voltage Current Voltage Current Voltage Current Voltage Current Voltage Current Voltage Current Voltage Current Voltage Current Voltage Current Current Voltage Voltage Current Current Voltage Monolithic Monolithic Monolithic Monolithic Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid Hybrid 0C to 70C 0C to 70C -25C to +85C -55Cto +125C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C 0C to 70C -25C to +85C -25C to +85C -25C to +85C -25C to +85C -55C to +125C -55C to +125C 0C to 70C 0C to 70C -25C to +85C -25C to +85C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/4 LSB 1/4 LSB 1/2 LSB 1/2 LSB 1/4 LSB 1/4 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/4 LSB 1/4 LSB 1/4 LSB 1/4 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB 1/2 LSB N-24A D-24 D-24 D-24 DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A DH-24A NOTES 1 For outline information see Package Information section. 2 Z-Suffix devices guarantee performance of 0 V to +5 V and 5 V spans with minimum supply voltages of 11.4 V. 3 These models have been discontinued. This is for historical information only. PRODUCT OFFERING Analog Devices has developed a number of technologies to support products within the data acquisition market. In serving the market new products are implemented with the technology best suited to the application. The DAC80 series of products was first implemented in hybrid form and now it is available in a single monolithic chip. We will provide both the hybrid and monolithic versions of the family so that in existing designs changes to documentation or product qualification will not have to be done. Specifications and ordering information for both versions are delineated in this data sheet. DIGITAL INPUT CODES Table I. Digital Input Codes Digital Input MSB CSB Compl. Straight Binary COB Compl. Offset Binary CTC* Compl. Two's Compl. +Full-Scale +1/2 Full-Scale Midscale Zero +Full-Scale Zero -1 LSB -Full-Scale -1 LSB -Full-Scale +Full-Scale Zero *Invert the MSB of the COB code with an external inverter to obtain CTC code. The ADDAC80 Series accepts complementary digital input code in binary (CBI) format. The CBI model may be connected by the user for anyone of three complementary codes: CSB, COB or CTC. REV. B LSB 000000000000 011111111111 100000000000 111111111111 Analog Input -7- ADDAC80/ADDAC85/ADDAC87 ACCURACY 18 Accuracy error of a D/A converter is the difference between the analog output that is expected when a given digital code is applied and the output that is actually measured with that code applied to the converter. Accuracy error can be caused by gain error, zero error, linearity error, or any combination of the three. Of these three specifications, the linearity error specification is the most important since it cannot be corrected. Linearity error is specified over its entire temperature range. This means that the analog output will not vary by more than its maximum specification, from an ideal straight line drawn between the end points (inputs all "1"s and all "0"s) over the specified temperature range. 10V 1-12 DATA IN SUMMING JUNCTION 15 2k TEKTRONIX 7A13 100pF 20 CF 25pF 10V HP6216A Figure 3a. Voltage Model Settling Time Circuit >1mV Differential linearity error of a D/A converter is the deviation from an ideal 1 LSB voltage change from one adjacent output state to the next. A differential linearity error specification of 1/2 LSB means that the output voltage step sizes can range from 1/2 LSB to 1 1/2 LSB when the input changes from one adjacent input state to the next. VOUT 5V 100 90 10 0% DRIFT Gain Drift 5V A measure of the change in the full scale range output over temperature expressed in parts per million of full scale range per C (ppm of FSR/C). Gain drift is established by: 1) testing the end point differences for each ADDAC80 model at the lowest operating temperature, 25C and the highest operating temperature; 2) calculating the gain error with respect to the 25C value and; 3) dividing by the temperature change. 500ns Figure 3b. Voltage Model Settling Time CF = 25 pF POWER SUPPLY SENSITIVITY Power supply sensitivity is a measure of the effect of a power supply change on the D/A converter output. It is defined as a percent of FSR per percent of change in either the positive or negative supplies about the nominal power supply voltages. Offset Drift A measure of the actual change in output with all "1"s on the input over the specified temperature range. The maximum change in offset is referenced to the offset at 25C and is divided by the temperature range. This drift is expressed in parts per million of full scale range per C (ppm of FSR/C). REFERENCE SUPPLY All models are supplied with an internal 6.3 V reference voltage supply. This voltage (Pin 24) is accurate to 1% and must be connected to the Reference Input (Pin 16) for specified operation. This reference may also be used externally with external current drain limited to 2.5 mA. An external buffer amplifier is recommended if this reference is to be used to drive other system components. Otherwise, variations in the load driven by the reference will result in gain variations. All gain adjustments should be made under constant load conditions. SETTLING TIME Settling time for each model is the total time (including slew time) required for the output to settle within an error band around its final value after a change in input. Voltage Output Models Three settling times are specified to 0.01% of full scale range (FSR); two for maximum full scale range changes of 20 V, 10 V and one for a 1 LSB change. The 1 LSB change is measured at the major carry (0 1 1 1 . . . 1 1 to 1 0 0 0 . . . 0 0), the point at which the worst case settling time occurs. The settling time characteristic depends on the compensation capacitor selected, the optimum value is 25 pF as shown in Figure 3a. ANALYZING DEVICE ACCURACY OVER THE TEMPERATURE RANGE For the purposes of temperature drift analysis, the major device components are shown in Figure 4. The reference element and buffer amplifier drifts are combined to give the total reference temperature coefficient. The input reference current to the DAC, IREF, is developed from the internal reference and will show the same drift rate as the reference voltage. The DAC output current, IDAC, which is a function of the digital input codes, is designed to track IREF; if there is a slight mismatch in these currents over temperature, it will contribute to the gain T.C. The bipolar offset resistor, RBP, and gain setting resistor, RGAIN, also have temperature coefficients that contribute to system drift errors. The input offset voltage drift of the output amplifier, OA, also contributes a small error. Current Output Models Two settling times are specified to 0.01% of FSR. Each is given for current models connected with two different resistive loads: 10 to 100 and 1000 to 1875 . Internal resistors are provided for connecting nominal load resistances of approximately 1000 to 1800 for output voltage ranges of 1 V and 0 V to -2 V. -8- REV. B ADDAC80/ADDAC85/ADDAC87 15V RGAIN RBP 6.3V 6.3k + - OA + - IREF IDAC DAC V- Figure 4. Bipolar Configuration There are three types of drift errors over temperature: offset, gain, and linearity. Offset drift causes a vertical translation of the entire transfer curve; gain drift is a change in the slope of the curve; and linearity drift represents a change in the shape of the curve. The combination of these three drifts results in the complete specification for total error over temperature. Note that if the DAC and application resistors track perfectly, the bipolar offset drift will be zero even if the reference drifts. A change in the reference voltage, which causes a shift in the bipolar offset, will also cause an equivalent change in IREF and thus IDAC, so that IDAC will always be exactly balanced by IBP with the MSB turned on. This effect is shown in Figure 5. The net effect of the reference drift then is simply to cause a rotation in the transfer around bipolar zero. However, consideration of second order effects (which are often overlooked) reveals the errors in the bipolar mode. The unipolar offset drifts previously discussed will have the same effect on the bipolar offset. A mismatch of RBP to the DAC resistors is usually the largest component of bipolar drift, but in the ADDAC80 this error is held to 10 ppm/C max. Gain drift in the DAC also contributes to bipolar offset drift, as well as full-scale drift, but again is held to 10 ppm/C max. ACTUAL UNIPOLAR Temperature error analysis in the unipolar mode is straightforward: there is an offset drift and a gain drift. The offset drift (which comes from leakage currents and drift in the output amplifier (OA)) causes a linear shift in the transfer curve as shown in Figure 5. The gain drift causes a change in the slope of the curve and results from reference drift, DAC drift, and drift in RGAIN relative to the DAC resistors. BIPOLAR RANGE ERRORS The analysis is slightly more complex in the bipolar mode. In this mode RBP is connected to the summing node of the output amplifier (see Figure 4) to generate a current that exactly balances the current of the MSB so that the output voltage is zero with only the MSB on. REV. B INPUT OUTPUT GAIN SHIFT INPUT OFFSET SHIFT BIPOLAR (IDEAL CASE) Figure 5. Unipolar and Bipolar Drifts MONOTONICITY AND LINEARITY UNIPOLAR ERRORS IDEAL OFFSET (ZERO) SHIFT Several new design concepts not previously used in DAC80-type devices contribute to a reduction in all the error factors over temperature. The incorporation of low temperature coefficient silicon-chromium thin-film resistors deposited on a single chip, a patented, fully differential, emitter weighted, precision current steering cell structure, and a T.C. trimmed buried Zener diode reference element results in superior wide temperature range performance. The gain setting resistors and bipolar offset resistor are also fabricated on the chip with the same SiCr material as the ladder network, resulting in low gain and offset drift. The initial linearity error of 1/2 LSB max and the differential linearity error of 3/4 LSB max guarantee monotonic performance over the specified range. It can therefore be assumed that linearity errors are insignificant in computation of total temperature errors. GAIN SHIFT OUTPUT Total error is defined as the deviation from a true straight line transfer characteristic from exactly zero at a digital input that calls for zero output to a point that is defined as full-scale. A specification for total error over temperature assumes that both the zero and full-scale points have been trimmed for zero error at 25C. Total error is normally expressed as a percentage of the full-scale range. In the bipolar situation, this means the total range from -VFS to +VFS. USING THE ADDAC80 SERIES POWER SUPPLY CONNECTIONS For optimum performance power supply decoupling capacitors should be added as shown in the connection diagrams. These capacitors (1 F electrolytic recommended) should be located close to the ADDAC80. Electrolytic capacitors, if used, should be paralleled with 0.01 F ceramic capacitors for optimum high frequency performance. EXTERNAL OFFSET AND GAIN ADJUSTMENT Offset and gain may be trimmed by installing external OFFSET and GAIN potentiometers. These potentiometers should be connected as shown in the block diagrams and adjusted as described below. TCR of the potentiometers should be 100 ppm/C or less. The 3.9 M and 10 M resistors (20% carbon or better) should be located close to the ADDAC80 to prevent noise pickup. If it is not convenient to use these high-value resistors, a functionally equivalent "T" network, as shown in Figure 8 may be substituted in each case. The gain adjust (Pin 23) is a high impedance point and a 0.01 F ceramic capacitor should be connected from this pin to common to prevent noise pickup. -9- ADDAC80/ADDAC85/ADDAC87 +VS +VS 1 24 REF CONTROL CIRCUIT 2 3 6 7 8 0.01F 12-BIT RESISTOR LADDER NETWORK AND CURRENT SWITCHES 9 2k 3k 19 12-BIT RESISTOR LADDER NETWORK AND CURRENT SWITCHES 6 7 17 8 6.3k 16 10 15 11 14 12 13 22 5k 19 10k TO 100k -VS 20 3.9M 10k TO 100k 5k +VS 18 1F 17 6.3k 9 3.9M 0.01F 21 5 +VS 18 23 4 1F 5k 10M REF CONTROL CIRCUIT 3 10k TO 100k 20 24 2 -VS 21 4 5 23 22 1 10k TO 100k 10M 16 - 10 15 + -VS 1F Figure 6. External Adjustment and Voltage Supply Connection Diagram, Current Model 11 14 12 13 -VS 1F Figure 7. External Adjustment and Voltage Supply Connection Diagram, Voltage Model Offset Adjustment 10M For unipolar (CSB) configurations, apply the digital input code that should produce zero potential output and adjust the OFFSET potentiometer for zero output. For bipolar (COB, CTC) configurations, apply the digital input code that should produce the maximum negative output voltage. Example: If the FULL SCALE RANGE is connected for 20 V, the maximum negative output voltage is -10 V. See Table II for corresponding codes. 270k 270k 7.8k 3.9M 180k 180k 10k Gain Adjustment Figure 8. Equivalent Resistances For either unipolar or bipolar configurations, apply the digital input that should give the maximum positive voltage output. Adjust the GAIN potentiometer for this positive full-scale voltage. See Table II for positive full-scale voltages. Table II. Digital Input Analog Output Digital Input 12-Bit Resolution MSB LSB 000000000000 011111111111 100000000000 111111111111 l LSB Analog Output Voltage* 0 to +10 V +9.9976 V +5.0000 V +4.9976 V 0.0000 V 2.44 mV Current 10 V +9.9951 V 0.0000 V 4.88 mV -10.0000 V -0.0049 V 0 to -2 mA -1.9995 mA -1.0000 mA -0.9995 mA 0.0000 mA 0.488 A 1 mA -0.9995 mA 0.0000 mA +0.0005 mA -1.00 mA 0.488 A *To obtain values for other binary ranges 0 to 5 V range: divide 0 to 10 values by 2; 5 V range: divide 10 V range values by 2; 2.5 V range: divide 10 V range values by 4. -10- REV. B ADDAC80/ADDAC85/ADDAC87 VOLTAGE OUTPUT MODELS TO REF CONTROL CIRCUIT Internal scaling resistors provided in the ADDAC80 may be connected to produce bipolar output voltage ranges of 10 V, 5 V or 2.5 V or unipolar output voltage ranges of 0 V to +5 V or 0 V to +10 V (see Figure 9). REF IN 2k 19 5k 15 20 16 6.3k 17 BIPOLAR OFFSET 21 COM Figure 10. Internal Scaling Resistors BIPOLAR OFFSET SUMMING JUNCTION FROM WEIGHTED RESISTOR NETWORK 17 3k 18 REF INPUT TO REF CONTROL CIRCUIT 6.3k 16 20 REFERENCE INPUT 18 5k 5k 6.3k 17 TO REF CONTROL CIRCUIT 16 15 19 I 0 TO 2mA OUTPUT - 15 + 6.6k 21 - The equivalent resistive scaling network and output circuit of the current model are shown in Figures 10 and 11. External RLS resistors are required to produce exactly 0 V to -2 V or 1 V output. TCR of these resistors should be 100 ppm/C or less to maintain the ADDAC80 output specifications. If exact output ranges are not required, the external resistors are not needed. COMMON V 6.3V Figure 9. Output Amplifier Voltage Range Scaling Circuit Gain and offset drift are minimized in the ADDAC80 because of the thermal tracking of the scaling resistors with other device components. Connections for various output voltage ranges are shown in Table III. Settling time is specified for a full-scale range change: 4 s for a 10 k feedback resistor; 3 s for a 5 k feedback resistor when using the compensation capacitor shown in Figure 3a. IOUT + 24 REFERENCE OUT Figure 11. ADDAC80 Current Model Equivalent Output Circuit Internal resistors are provided to scale an external op amp or to configure a resistive load to offer two output voltage ranges of 1 V or 0 V to -2 V. These resistors (RLI TCR = 20 ppm/C) are an integral part of the ADDAC80 and maintain gain and bipolar offset drift specifications. If the internal resistors are not used, external RL (or RF) resistors should have a TCR of 25 ppm/C or less to minimize drift. This will typically add 50 ppm/C + the TCR of RL (or RF) to the total drift. Table III. Output Voltage Range Connections, Voltage Model ADDAC80 Output Range Digital Input Codes Connect Pin 15 to Connect Pin 17 to Connect Pin 19 to Connect Pin 16 to 10 V 5 V 2.5 V 0 V to 10 V 0 V to 5 V 0 V to 10 V COB or CTC COB or CTC COB or CTC CSB CSB CCD 19 18 18 18 18 19 20 20 20 21 21 NC 15 NC 20 NC 20 15 24 24 24 24 24 24 NC = No Connect DRIVING A RESISTIVE LOAD UNIPOLAR 15 A load resistance, RL = RLI, + RLS, connected as shown in Figure 12 will generate a voltage range, VOUT, determined by: VOUT 6.6 k x RL = -2 mA 6.6 k + RL 0 TO 2mA RLI 968 6.6k 18 + RLS 21 COMMON (1) VOUT - CURRENT CONTROLLED BY DIGITAL INPUT where RL max = 1.54 k and VOUT max = -2.5 V To achieve specified drift, connect the internal scaling resistor (RLI) as shown in Table IV to an external metal film trim resistor (RLS) to provide full scale output voltage range of 0 V to -2 V. With RLS = 0 V, VOUT = -1.69 V. REV. B Figure 12. Equivalent Circuit ADDAC80-CBI-I Connected for Unipolar Voltage Output with Resistive Load -11- ADDAC80/ADDAC85/ADDAC87 DRIVING A RESISTOR LOAD BIPOLAR R x 3.22 k VOUT = 1 mA L RL + 3.22 k 20V RANGE 19 The equivalent output circuit for a bipolar output voltage range is shown in Figure 13, RL = RLI + RLS. VOUT is determined by: 5k CBI 18 10V RANGE 5k 15 (2) I 0 TO 2mA where RL max = 11.18 k and VOUT max = 2.5 V A 6.6k AD509KH* VOUT 21 To achieve specified drift, connect the internal scaling resistors (RLI) as shown in Table IV for the COB or CTC codes and add an external metal film resistor (RLS) in series to obtain a full scale output range of 1 V. In this configuration, with RLS equal to zero, the full scale range will be 0.874 V. *FOR FAST SETTLING TIME Figure 14. External Op Amp Using Internal Feedback Resistors OUTPUT LARGER THAN 20 V RANGE 15 1mA RLI 1.2k 3.22k 20 For output voltage ranges larger than 10 V, a high voltage op amp may be employed with an external feedback resistor. Use IOUT values of l mA for bipolar voltage ranges and -2 mA for unipolar voltage ranges (see Figure 15). Use protection diodes when a high voltage op amp is used. + RLS 21 COMMON VOUT - CURRENT CONTROLLED BY DIGITAL INPUT The feedback resistor, RF, should have a temperature coefficient as low as possible. Using an external feedback resistor, overall drift of the circuit increases due to the lack of temperature tracking between RF and the internal scaling resistor network. This will typically add 50 ppm/C + RF drift to total drift. Figure 13. ADDAC80-CBI-I Connected for Bipolar Output Voltage with Resistive Load DRIVING AN EXTERNAL OP AMP The current model ADDAC80 will drive the summing junction of an op amp used as a current to voltage converter to produce an output voltage. As seen in Figure 14, VOUT = I OUT x R F 17 RF 6.3k 16 (3) 15 I 0 TO 2mA where IOUT is the ADDAC80 output current and RF is the feedback resistor. Using the internal feedback resistors of the current model ADDAC80 provides output voltage ranges the same as the voltage model ADDAC80. To obtain the desired output voltage range when connecting an external op amp, refer to Table V and Figure 14. 171K* 6.6k VOUT 21 - V + VREF 6.3V 24 *FOR OUTPUT VOLTAGE SWINGS UP TO 140V p-p Figure 15. External Op Amp Using External Feedback Resistors Table IV. Current Model/Resistive Load Connections 1% Metal Film RLI Connections Reference Bipolar Offset Internal External Resistance Resistance Connect Connect Connect Connect Connect RLI (k) RLS Pin 15 to Pin 18 to Pin 20 to Pin 16 to Pin 17 to RLS Digital Input Codes Output Range CSB 0 to -2 V 0.968 COB or CTC 1 V CCD 1.2 0 to 2 V 3 210 20 19 and RLS 15 24 Com (21) 249 18 19 RLS 24 15 N/A NC 21 NC 24 NC -12- Between Pin 18 and Com (21) Between Pin 20 and Com (21) N/A REV. B ADDAC80/ADDAC85/ADDAC87 Table V. External Op Amp Voltage Mode Connections Output Range Digital Input Codes Connect A to Connect Pin 17 to Connect Pin 19 to Connect Pin 16 to 10 V 5 V 2.5 V 0 V to 10 V 0 V to 5 V COB or CTC COB or CTC COB or CTC CSB CSB 19 18 18 18 18 15 15 15 21 21 A NC 15 NC 15 24 24 24 24 24 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 24-Lead Plastic DIP (N-24A) 1.290 (32.70) 1.150 (29.30) 24 13 0.580 (14.73) 0.485 (12.32) 1 12 PIN 1 0.625 (15.87) 0.600 (15.24) 0.060 (1.52) 0.015 (0.38) 0.250 (6.35) MAX 0.200 (5.05) 0.125 (3.18) 0.195 (4.95) 0.125 (3.18) 0.150 (3.81) MIN 0.022 (0.558) 0.014 (0.356) 0.100 (2.54) BSC 0.015 (0.381) 0.008 (0.204) 0.070 (1.77) SEATING 0.030 (0.77) PLANE CONTROLLING DIMENSIONS ARE IN MILLIMETERS: INCH DIMENSIONS ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 24-Lead Ceramic DIP (D-24) SEE NOTE 5 0.098 (2.49) MAX 0.005 (0.13) MIN 24 13 0.610 (15.49) 0.500 (12.70) SEE NOTE 4 PIN 1 SEE NOTE 1 1 12 SEE NOTE 4 1.290 (32.77) MAX 0.225 (5.72) MAX SEE NOTE 3 0.075 (1.91) 0.015 (0.38) 0.150 (3.81) 0.200 (5.08) MIN 0.120 (3.05) SEATING 0.023 (0.58) 0.110 (2.79) 0.070 (1.78) PLANE 0.014 (0.36) 0.090 (2.29) 0.030 (0.76) 0.620 (15.75) 0.590 (14.99) 0.015 (0.38) 0.008 (0.20) SEE NOTE 6 SEE NOTE 7 SEE NOTE 2, 6 NOTES 1. INDEX AREA; A NOTCH OR A LEAD ONE IDENTIFICATION MARK IS LOCATED ADJACENT TO LEAD ONE. 2. THE MINIMUM LIMIT FOR DIMENSION MAY BE 0.023" (0.58 mm) FOR ALL FOUR CORNER LEADS ONLY. 3. DIMENSION SHALL BE MEASURED FROM THE SEATING PLANE TO THE BASE PLANE. 4. THIS DIMENSION ALLOWS FOR OFF-CENTER LID, MENISCUS AND GLASS OVERRUN. 5. APPLIES TO ALL FOUR CORNERS. 6. ALL LEADS -- INCREASE MAXIMUM LIMIT BY 0.003" (0.08 mm) MEASURED AT THE CENTER OF THE FLAT, WHEN HOT SOLDER DIP LEAD FINISH IS APPLIED. 7. TWENTY TWO SPACES. 8. CONTROLLING DIMENSIONS ARE IN MILLIMETERS. INCH DIMENSIONS ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN REV. B -13- ADDAC80/ADDAC85/ADDAC87 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 24-Lead Side Brazed Ceramic DIP for Hybrid (DH-24A) SEE NOTE 5 0.005 (0.13) MIN 24 0.098 (2.49) MAX 13 PIN 1 SEE NOTE 1 1 12 SEE NOTE 3 0.075 (1.91) 1.212 (29.69) MAX 0.015 (0.38) 0.225 (5.72) MAX 0.180 (4.57) 0.200 (5.08) MIN 0.120 (3.05) 0.023 (0.58) 0.100 (2.54) 0.070 (1.78) SEATING BSC 0.030 (0.76) PLANE 0.014 (0.36) SEE NOTE 4, 7 SEE NOTE 2 0.600 (14.70) 0.580 (14.21) 0.015 (0.38) 0.008 (0.20) 0.620 (15.75) 0.590 (14.99) SEE NOTE 6 NOTES 1. INDEX AREA; A NOTCH OR A LEAD ONE IDENTIFICATION MARK IS LOCATED ADJACENT TO LEAD ONE. 2. THE MINIMUM LIMIT FOR DIMENSION MAY BE 0.023" (0.58 mm) FOR ALL FOUR CORNER LEADS ONLY. 3. DIMENSION SHALL BE MEASURED FROM THE SEATING PLANE TO THE BASE PLANE. 4. THE BASIC PIN SPACING IS 0.100" (2.54 mm) BETWEEN CENTERLINES. 5. APPLIES TO ALL FOUR CORNERS. 6. SHALL BE MEASURED AT THE CENTERLINE OF THE LEADS. 7. TWENTY TWO SPACES. 8. CONTROLLING DIMENSIONS ARE IN MILLIMETERS: INCH DIMENSIONS ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. -14- REV. B ADDAC80/ADDAC85/ADDAC87 Revision History Location Page Data Sheet changed from REV. A to REV. B. Update OUTLINE DIMENSION drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 REV. B -15- -16- PRINTED IN U.S.A. C00381-0-1/02(B)