Product Specification PE4244 SPDT UltraCMOSTM RF Switch Product Description Features The PE4244 UltraCMOSTM RF Switch is designed to cover a broad range of applications from DC to 3.0 GHz. This switch integrates on-board CMOS control logic with a low voltage CMOS compatible control input. Using a +3-volt nominal power supply voltage, a 1 dB compression point of +27 dBm can be achieved. The PE4244 also exhibits excellent isolation of 39 dB at 1.0 GHz and is offered in a small 8-lead MSOP package. * Single +3.0-volt Power Supply * Low Insertion loss: 0.60 dB up to 2.0 GHz * High isolation of 39 dB at 1.0 GHz, 29 dB at 2.0 GHz * Typical 1 dB compression of +27 dBm The PE4244 UltraCMOSTM RF Switch is manufactured in Peregrine's patented Ultra Thin Silicon (UTSi(R)) CMOS process, offering the performance of GaAs with the economy and integration of conventional CMOS. * Single-pin CMOS logic control * Packaged in 8-lead MSOP Figure 2. Package Type Figure 1. Functional Diagram 8-lead MSOP RFC RF1 RF2 CMOS Control Driver CTRL Table 1. Electrical Specifications @ +25 C, VDD = 3 V (ZS = ZL = 50 ) Parameter Operation Frequency Conditions 1 Insertion Loss Isolation - RFC to RF1/RF2 Isolation - RF1 to RF2 Return Loss Minimum Typical DC 1000 MHz 2000 MHz 1000 MHz 2000 MHz 1000 MHz 2000 MHz 1000 MHz 2000 MHz 37 27 34 26 19 22 0.60 0.60 39 29 36 28 20 25 Maximum Units 3000 MHz 0.75 0.75 dB dB dB dB dB dB dB dB `ON' Switching Time CTRL to 0.1 dB final value, 2 GHz 200 ns `OFF' Switching Time CTRL to 25 dB isolation, 2 GHz 90 ns 15 mVpp Video Feedthrough2 Input 1 dB Compression 2000 MHz 26 27 dBm Input IP3 2000 MHz, 14dBm 43 45 dBm Notes: 1. Device linearity will begin to degrade below 10 MHz. 2. The DC transient at the output of any port of the switch when the control voltage is switched from Low to High or High to Low in a 50 test set-up, measured with 1ns risetime pulses and 500 MHz bandwidth. Document No. 70-0103-03 www.psemi.com (c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 7 PE4244 Product Specification Figure 3. Pin Configuration (Top View) 1 VDD CTRL 2 GND RFC 8 RF1 7 GND 3 6 GND 4 5 RF2 4244 Table 3. Absolute Maximum Ratings Symbol Parameter/Conditions Min Max Units VDD Power supply voltage -0.3 4.0 V VI Voltage on any input -0.3 VDD+ V TST Storage temperature range -65 150 C TOP Operating temperature -40 85 C PIN Input power (50) 30 dBm VESD ESD voltage (Human Body 1500 V Table 2. Pin Descriptions Pin No. Pin Name 1 VDD 2 CTRL Description Nominal 3 V supply connection. A bypass capacitor (100 pF) to the ground plane should be placed as close as posCMOS logic level: High = RFC to RF1 signal path Absolute Maximum Ratings are those values listed in the above table. Exceeding these values may cause permanent device damage. Functional operation should be restricted to the limits in the DC Electrical Specifications table. Exposure to absolute maximum ratings for extended periods may affect device reliability. Table 4. DC Electrical Specifications 3 4 GND RFC Ground connection. Traces should be physically short and connected to Common RF port for switch (Note 1) Parameter Min VDD Power Supply Voltage 2.7 Typ IDD Power Supply Current 5 RF2 RF2 port (Note 1) 6 GND Ground Connection. Traces should be physically short and connected to 7 GND Ground Connection. Traces should be physically short and connected to 8 RF1 RF1 port (Note 1) Note 1: All RF pins must be DC blocked with an external series capacitor or held at 0 VDC. VDD = 3V, VCNTL = 3V Control Voltage High Max Units 3.0 3.3 V 250 500 nA 0.3xVDD V 0.7xVDD V Control Voltage Low Electrostatic Discharge (ESD) Precautions When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the specified rating. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up. Table 5. Control Logic Truth Table Control Voltage (c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 7 Signal Path CTRL = CMOS High RFC to RF1 CTRL = CMOS Low RFC to RF2 Document No. 70-0103-03 UltraCMOSTM RFIC Solutions PE4244 Product Specification Evaluation Kit The SPDT Switch Evaluation Kit board was designed to ease customer evaluation of the PE4244 SPDT switch. The RF common port is connected through a 50 transmission line to the top left SMA connector, J1. Port 1 and Port 2 are connected through 50 transmission lines to the top two SMA connectors on the right side of the board, J3 and J4. A through transmission line connects SMA connectors J6 and J8. This transmission line can be used to estimate the loss of the PCB over the environmental conditions being evaluated. Figure 4. Evaluation Board Layout Peregrine specification 101/0037 The board is constructed of a two metal layer FR4 material with a total thickness of 0.031". The bottom layer provides ground for the RF transmission lines. The transmission lines were designed using a coplanar waveguide with ground plane model using a trace width of 0.030", trace gaps of 0.007", dielectric thickness of 0.028", metal thickness of 0.0014" and r of 4.4. J2 provides a means for controlling DC and digital inputs to the device. Starting from the lower left pin, the second pin to the right (J2-3) is connected to the device CTRL input. The fourth pin to the right (J2-7) is connected to the device VDD input. A decoupling capacitor (100 pF) is provided on both CTRL and VDD traces. It is the responsibility of the customer to determine proper supply decoupling for their design application. Removing these components from the evaluation board has not been shown to degrade RF performance. Figure 5. Evaluation Board Schematic Peregrine specification 101/0147 Document No. 70-0103-03 www.psemi.com (c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 7 PE4244 Product Specification Typical Performance Data @ -40 C to 85 C (Unless otherwise noted) Figure 7. Input 1 dB Compression Point & IIP3 Figure 6. Insertion Loss - RFC to RF1 0 -40C 85C -0.9 IIP3 (dBm) -0.6 25C 60 50 50 40 40 30 30 1dB Compression Point (dBm) Insertion Loss (dB) -0.3 60 -1.2 -1.5 20 0 500 1000 1500 2000 2500 3000 0 500 1000 Frequency (MHz) 2000 2500 20 3000 Frequency (MHz) Figure 9. Isolation - RFC to RF1 Figure 8. Insertion Loss - RFC to RF2 0 0 -20 -0.3 -40C Isolation (dB) Insertion Loss (dB) 1500 -0.6 85C -0.9 25C -40 -60 -80 -1.2 -100 -1.5 0 500 1000 1500 2000 2500 3000 Frequency (MHz) (c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 7 0 500 1000 1500 2000 2500 3000 Frequency (MHz) Document No. 70-0103-03 UltraCMOSTM RFIC Solutions PE4244 Product Specification Typical Performance Data @ -40 C to 85 C (Unless otherwise noted) Figure 10. Isolation - RFC to RF2 Figure 11. Isolation - RF1 to RF2, RF2 to RF1 0 0 -20 -40 Isolation (dB) Isolation (dB) -25 -60 -50 -75 -80 -100 -100 0 500 1000 1500 2000 2500 0 3000 500 1000 Frequency (MHz) Figure 12. Return Loss - RFC to RF1, RF2 2000 2500 3000 2500 3000 Figure 13. Return Loss - RF1, RF2 0 0 -10 -10 Return Loss (dB) Return Loss (dB) 1500 Frequency (MHz) RF1 -20 -30 RF1 -20 -30 RF2 RF2 -40 -40 0 500 1000 1500 2000 Frequency (MHz) Document No. 70-0103-03 www.psemi.com 2500 3000 0 500 1000 1500 2000 Frequency (MHz) (c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 5 of 7 PE4244 Product Specification Figure 14. Package Drawing 8-lead MSOP TOP VIEW 0.65BSC .525BSC 7 8 6 5 2.450.10 2X 3.000.10 0.510.13 -B- 0.510.13 1 2 3 4 .25 A B C -C- 2.950.10 0.860.08 2.950.10 1.10 MAX -A0.10 +0.07 0.33 -0.08 A 0.08 3.000.10 0.100.05 4.900.15 A B C 3.000.10 FRONT VIEW SIDE VIEW Table 6. Ordering Information Order Code Part Marking Description Package Shipping Method 4244-01 4244 PE4244-08MSOP-50A 8-lead MSOP 50 units / Tube 4244-02 4244 PE4244-08MSOP-2000C 8-lead MSOP 2000 units / T&R 4244-00 PE4244-EK PE4244-08MSOP-EK Evaluation Kit 1 / Box 4244-51 4244 PE4244G-08MSOP-50A Green 8-lead MSOP 50 units / Tube 4244-52 4244 PE4244G-08MSOP-2000C Green 8-lead MSOP 2000 units / T&R (c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 6 of 7 Document No. 70-0103-03 UltraCMOSTM RFIC Solutions PE4244 Product Specification Sales Offices The Americas North Asia Pacific Peregrine Semiconductor Corp. Peregrine Semiconductor K.K. 9450 Carroll Park Drive San Diego, CA 92121 Tel 858-731-9400 Fax 858-731-9499 5A-5, 5F Imperial Tower 1-1-1 Uchisaiwaicho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Europe Peregrine Semiconductor Europe Commercial Products: Batiment Maine 13-15 rue des Quatre Vents F- 92380 Garches, France Tel: +33-1-47-41-91-73 Fax : +33-1-47-41-91-73 Space and Defense Products: 180 Rue Jean de Guiramand 13852 Aix-En-Provence cedex 3, France Tel: +33(0) 4 4239 3361 Fax: +33(0) 4 4239 7227 South Asia Pacific Peregrine Semiconductor 28G, Times Square, No. 500 Zhangyang Road, Shanghai, 200122, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). Document No. 70-0103-03 www.psemi.com The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS is a trademark of Peregrine Semiconductor Corp. (c)2005 Peregrine Semiconductor Corp. All rights reserved. Page 7 of 7