DATA SHEET TRIMMABLE CHIP RESISTORS TR series (Pb Free) 0/-10%, 0/-20%, 0/-30% Product specification - Oct 18, 2005 V.0 sizes 0402/0603/0805/1206 Product specification Chip Resistor Surface Mount TR SERIES SCOPE 2 10 0402 to 1206 (Pb Free) APPLICATIONS Hand-held measuring equipment This specification describes TR0402/0603/0805/1206 trimmable chip resistors with lead-free terminations made by thick film process. Mobile phones Camcorders ORDERING INFORMATION Portable radios, CD and cassette Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and resistance value. Tuners Photo sensors PHYCOMP ORDERING CODE 12NC CODE 2350/2322 ORDERING EXAMPLE XXX XXXXX L (1) (2) SIZE TYPE START TOL. IN (1) (%) 0402 RC32TR 2350 (5) European 2322 0603 RC22TR 2350 (3) (4) RESISTANCE PAPER/PE TAPE ON REEL (units) (2) RANGE 10,000 5,000/10,000 5,000 0/-10% 1 to 10 M 503 22xxx - 0/-20% 1 to 10 M 503 21xxx - 0/-30% 1 to 10 M 503 20xxx - on request 1 to 10 M - on request - 0/-10% 1 to 10 M - 502 12xxx 0/-20% 1 to 10 M - 502 11xxx 0/-30% 1 to 10 M - 502 10xxx The ordering code of a RC22TR resistor, value 330 X with 0/-30% tolerance, supplied in tape of 5,000 units per reel is: 235050210331L. For size 1206 of European type resistors, the ordering code is 232272494xxxL. "xxx" represents special code for customized combination of resistance, tolerance, size and packing. This code can be supplied on request. European 2322 on request 1 to 10 M - 0805 RC12TR 2350 0/-10% 1 to 10 M - 501 12xxx Resistance decade (3) 0/-20% 1 to 10 M - 501 11xxx 0.01 to 0.0976 X 0 0/-30% 1 to 10 M - 501 10xxx 0.1 to 0.976 X 7 1 to 9.76 X 8 on request Last digit of 12NC - Last digit European 2322 on request 1 to 10 M - 1206 RC02TR 2350 0/-10% 1 to 10 M - 500 12xxx 10 to 97.6 X 9 0/-20% 1 to 10 M - 500 11xxx 100 to 976 X 1 0/-30% 1 to 10 M - 500 10xxx 1 to 9.76 kX 2 on request 1 to 10 M - - 10 to 97.6 kX 3 with the last digit indicating the multiplier as shown in the table of "Last digit of 12NC". 100 to 976 kX 4 1 to 9.76 MX 5 10 to 97.6 MX 6 European 2322 (1) The resistors have a 12-digit ordering code starting with 2350/2322. (2) The subsequent 5 digits indicate the resistor tolerance and packaging. 734 94xxx - 724 94xxx (4) "L" means lead-free terminations (a) . Example: (5) European type products are covered with transparent lacquer (3) The remaining 3 digits in stead of transparent glass layer. represent the resistance value 0.02 X = 0200 or 200 0.3 X = 3007 or 307 1X = 1008 or 108 33 kX = 3303 or 333 10 MX = 1006 or 106 NOTE a. The "L" at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp "LFP"= lead free production. b. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet. c. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006) www.yageo.com Oct 18, 2005 V.0 Product specification Chip Resistor Surface Mount TR SERIES 3 10 0402 to 1206 (Pb Free) CTC CODE TR XXXX X X X XX XXXX L (1) (2) (3) (4) (5) (6) (7) (1) SIZE 0402/0603/0805/1206 (2) TOLERANCE K = 0/-10% M = 0/-20% N = 0/-30% (3) PACKAGING TYPE R = Paper/PE taping reel (4) TEMPERATURE COEFFICIENT OF RESISTANCE - = Base on spec (5) TAPING REEL 07 = 7 inch dia. Reel 7T = European type (d) ORDERING EXAMPLE The ordering code of a TR0603 chip resistor, value 330 X with 0/-30% tolerance, supplied in 7-inch tape reel is: TR0603NR-07330RL. For size 1206 of European type resistor, value 330 X with 0/-30% tolerance, supplied in 7-inch tape reel, the ordering code is: TR1206NR-7T330RL. NOTE a. The "L" at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp "LFP"= lead free production. b. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet. c. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006) d. European type products are covered with transparent lacquer in stead of transparent glass layer. (6) RESISTANCE VALUE 5R6, 56R, 560R, 56K, 1M, 10M. (7) RESISTOR TERMINATIONS (a) L = Lead-free terminations (matte tin) www.yageo.com Oct 18, 2005 V.0 Product specification Chip Resistor Surface Mount TR SERIES 4 10 0402 to 1206 (Pb Free) MARKING TR0402/0603/0805/1206 No marking ynsc007 Fig. 1 For marking codes, please see EIA-marking code rules in data sheet "Chip resistors marking". CONSTRUCTION The resistors are constructed on a high-grade ceramic body (aluminium oxide). Internal metal electrodes are added at each end and a connection is made between them using a resistive metal glaze; the approximate resistor values are dependent on the composition of the glaze. The resistive layer is covered with a translucent protective coat. Finally, two end electrodes are added, the composition of which has been designed to provide ease of soldering. See fig. 2. OUTLINES For dimension see Table 1 overcoat resistive layer inner electrode H termination ceramic substrate I2 overcoat I1 DIMENSIONS Table 1 For outlines see fig. 2 TYPE L (mm) W (mm) H (mm) W I1 (mm) I2 (mm) TR0402 1.00 0.10 0.50 0.05 0.35 0.05 0.20 0.10 0.25 0.10 TR0603 1.60 0.10 0.80 0.10 0.45 0.10 0.25 0.15 0.25 0.15 TR0805 2.00 0.10 1.25 0.10 0.50 0.10 0.35 0.20 0.35 0.20 YNSC057 L Fig. 2 Chip resistor outlines TR1206 3.10 0.10 1.60 0.10 0.55 0.10 0.45 0.20 0.40 0.20 www.yageo.com Oct 18, 2005 V.0 Product specification Chip Resistor Surface Mount TR SERIES 5 10 0402 to 1206 (Pb Free) ELECTRICAL CHARACTERISTICS Table 2 CHARACTERISTICS TYPE RESISTANCE RANGE TR0402 Rated Operating Max. Max. Dielectric Power Temperature Working Overload Withstanding Range Voltage Voltage Voltage 1/16 W TR0603 0/-10%, 0/-20%, 0/-30%: 1/16 W TR0805 1 to 10 M (E-24) TR1206 1/8 W 1/4 W -55 C to +125 C -55 C to +155 C 50 V 100 V 100 V 50 V 100 V 100 V 150 V 300 V 500 V 200 V 500 V 500 V Temperature Coefficient of Resistance 1 R 10 : 200 ppm/C 10 < R 1 M: 100 ppm/C 1 M < R 10 M: 200 ppm/C FOOTPRINT AND SOLDERING PROFILES ENVIRONMENTAL DATA For recommended footprint and soldering profiles, please see the special data sheet "Chip resistors mounting". For material declaration information (IMDS-data) of the products, please see the separated info "Environmental data" conformed to EU RoHS. PACKING STYLE AND PACKAGING QUANTITY Table 3 Packing style and packaging quantity PACKING STYLE Paper/PE taping reel (R) REEL DIMENSION TR0402 TR0603 TR0805 TR1206 7" (178 mm) 10,000 5,000 5,000 5,000 NOTE 1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet "Packing" document. www.yageo.com Oct 18, 2005 V.0 Product specification Chip Resistor Surface Mount SERIES TR 6 10 0402 to 1206 (Pb Free) FUNCTIONAL DESCRIPTION PRODUCT CHARACTERIZATION OPERATING TEMPERATURE RANGE Standard values of nominal resistance are taken from the E24 series for resistors with a tolerance of 0/-10%, 0/-20% and 0/-30%. The values of the E24 series are in accordance with "IEC publication 60063". Each type range: TR0402/0603: -55C to +125C; TR0805/1206: -55C to +155C. LIMITING VALUES Table 4 TYPE LIMITING VOLTAGE (V) (1) LIMITING POWER (W) TR0402 50 1/16 TR0603 50 1/16 TR0805 150 1/8 TR1206 200 1/4 For both types: TR0805/1206 For both types: TR0402/0603 handbook, P halfpage MLB206 max (%Prated ) 100 MRA632 Pmax (%Prated) 100 50 50 0 55 0 50 70 100 125 o Tamb ( C) 0 -55 0 50 70 155 100 Tamb (C) NOTES 1. The maximum voltage that may be continuously applied to the resistor element, see "IEC publication 60115-8". Fig. 3 Maximum dissipation (Pmax) in percentage of rated power as a function of the operating ambient temperature (Tamb) POWER RATING Each type rated power at 70C: TR0402=1/16 W; TR0603=1/16 W; TR0805=1/8 W; TR1206=1/4 W. APPLICATION INFORMATION TRIMMING INSTRUCTIONS WITH YAG-LASER Typical values for: Cutting speed = 10 to 300 mm/s RATED VOLTAGE Laser power = 1 to 6 W The DC or AC (rms) continuous working voltage corresponding to the rated power is determined by the following formula: Maximum trimming length = 60% of resistor film width V = (P X R) Where V = Continuous rated DC or AC (rms) working voltage (V) Minimum distance between end termination and trimming cut = TR0402/0603: 0.20 mm TR0805/1206: 0.50 mm PROTECTION OF LASER CUT With epoxy-phenol lacquers, epoxy resins or silicon alkyd-resins. This is necessary for humidity tests and stability at load. P = Rated power (W) R = Resistance value (X) www.yageo.com Oct 18, 2005 V.0 Product specification Chip Resistor Surface Mount TR SERIES 7 10 0402 to 1206 (Pb Free) TESTS AND REQUIREMENTS Table 5 Test condition, procedure and requirements TEST Temperature Coefficient of Resistance (T.C.R.) TEST METHOD PROCEDURE REQUIREMENTS MIL-STD-202F-method 304; At +25/-55 C and +25/+125 C Refer to table 2 JIS C 5202-4.8 Formula: R2-R1 T.C.R= ------------------------x106 (ppm/C) R1(t2-t1) Where t1=+25 C or specified room temperature t2=-55 C or +125 C test temperature R1=resistance at reference temperature in ohms R2=resistance at test temperature in ohms Thermal Shock MIL-STD-202F-method 107G; IEC 60115-1 4.19 At -65 (+0/-10) C for 2 minutes and at UCT (+10/-0) C for 2 minutes; 25 cycles (1.0%+0.05 ) UCT: 0402/0603: 125 C 0805/1206: 155 C Low Temperature Operation MIL-R-55342D-Para 4.7.4 Short Time Overload MIL-R-55342D-Para 4.7.5; At -65 (+0/-5) C for 1 hour; RCWV applied for 45 (+5/-0) minutes (1.0%+0.05 ) (1.0%+0.05 ) IEC 60115-1 4.13 2.5 x RCWV applied for 5 seconds at room temperature Insulation Resistance MIL-STD-202F-method 302; One DC voltage (V) applied for 1 minute 10 G IEC 60115-1 4.6.1.1 Details see below table 6 Dielectric Withstand Voltage MIL-STD-202F-method 301; One AC voltage (Vrms) applied for 1 minute IEC 60115-1 4.6.1.1 Details see below table 6 Resistance to Soldering Heat MIL-STD-202F-method 210C; Unmounted chips; 260 5 C for 10 1 seconds (1.0%+0.05 ) Life MIL-STD-202F-method 108A; At 702 C for 1,000 hours; RCWV applied for 1.5 hours on and 0.5 hour off (1.0%+0.05 ) IEC 60115-1 4.18 IEC 60115-1 4.25.1 No visible damage No visible damage No breakdown or flashover No visible damage www.yageo.com Oct 18, 2005 V.0 8 Product specification Chip Resistor Surface Mount TR SERIES 10 0402 to 1206 (Pb Free) Table 5 Test condition, procedure and requirements (continued) TEST Solderability Bending Strength TEST METHOD PROCEDURE REQUIREMENTS MIL-STD-202F-method 208A; Solder bath at 2453 C Well tinned (95% covered) IEC 60115-1 4.17 Dipping time: 20.5 seconds No visible damage Resistors mounted on a 90 mm glass epoxy resin PCB (FR4) (1.0%+0.05 ) JIS C 5202.6.14; IEC 60115-1 4.15 No visible damage Bending: 5 mm Resistance to Solvent Noise MIL-STD-202F-method 215; lsopropylalcohol (C3H7OH) or dichloromethane (CH2Cl2) followed by brushing No smeared IEC 60115-1 4.29 JIS C 5202 5.9; Maximum voltage (Vrms) applied Resistors range Value R < 100 10 dB 100 R < 1 K 20 dB 1 K R < 10 K 30 dB 10 K R < 100 K 40 dB 100 K R < 1 M 46 dB 1 M R 22 M 48 dB IEC 60115-1 4.12 Humidity (steady state) Leaching Intermittent Overload Resistance to Vibration Moisture Resistance Heat JIS C 5202 7.5; 1,000 hours; 402 C; 93(+2/-3)% RH IEC 60115-8 4.24.8 R < 1 M: (1.0%+0.05 ) RCWV applied for 1.5 hours on and 0.5 hour off R 1 M: (1.5%+0.05 ) EIA/IS 4.13B; Solder bath at 2605 C No visible damage IEC 60115-8 4.18 Dipping time: 301 seconds JIS C 5202 5.8 At room temperature; 2.5 x RCWV applied for 1 second on and 25 seconds off; total 10,000 cycles On request On request MIL-STD-202F-method 106F; 42 cycles; total 1,000 hours (2.0%+0.05) IEC 60115-1 4.24.2 Shown as Fig. 4 No visible damage (1.0%+0.05 ) Table 6 Criteria of rated continued working voltage and overload voltage TYPE Voltage (DC/unit: V); (AC/ unit: Vrms) TR0402 TR0603 TR0805 TR1206 100 100 300 500 www.yageo.com Oct 18, 2005 V.0 Product specification Chip Resistor Surface Mount 75 TR 80 - 98% RH 90 - 98% RH temperature [C] SERIES 90 - 98% RH 80 - 98% RH 9 10 0402 to 1206 (Pb Free) 90 - 98% RH initial drying 24 hours rate of change of temperature is unspecified, however, specimens shall not be subjected to radiant heating from chamber conditioning processes 50 end of final cycle; measurements as specified in 2.7 +10 C (+18 F) -2 C (-3.6 F) 25 initial measurements as specified in 2.2 0 temperature tolerance 2 C (3.6 F) unless otherwise specified voltage applied as specified in 2.4 STEP1 STEP2 prior to first cycle only HBK073 optional sub-cycle if specified (2.3); sub-cycle performed during any 5 of the first 9 cycles; humidity uncontrolled during sub-cycle circulation of conditioning air shall be at a minimum cubic rate per minute equivalent to 10 times the volume of the chamber STEP3 STEP4 STEP5 STEP6 STEP7 one cycle 24 hours; repeat as specified in 2.5 0 5 10 15 20 25 time [h] Fig. 4 Moisture resistance test requirements www.yageo.com Oct 18, 2005 V.0 Product specification Chip Resistor Surface Mount TR SERIES 10 10 0402 to 1206 (Pb Free) REVISION HISTORY REVISION DATE Version 0 CHANGE NOTIFICATION Oct 18, 2005 - DESCRIPTION - New datasheet for trimmable chip resistors sizes of 0402/0603/0805/1206, 0/-10%, 0/-20, and 0/-30% tolerance with lead-free terminations - Replace the 0603/0805/1206 parts of pdf files: RC02TR_12TR_9.pdf, RC22_TR_3.pdf, and combine into a document. - Test method and procedure updated - PE tape added (paper tape will be replaced by PE tape) www.yageo.com Oct 18, 2005 V.0