TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 D D D D D D Output Swing Includes Both Supply Rails Low Noise . . . 12 nV/Hz Typ at f = 1 kHz Low Input Bias Current . . . 1 pA Typ Fully Specified for Both Single-Supply and Split-Supply Operation Low Power . . . 500 A Max Common-Mode Input Voltage Range Includes Negative Rail D D D D Low Input Offset Voltage 950 V Max at TA = 25C (TLV226xA) Wide Supply Voltage Range 2.7 V to 8 V Macromodel Included Available in Q-Temp Automotive HighRel Automotive Applications Configuration Control / Print Support Qualification to Automotive Standards description 4 VDD = 3 V 3.5 VOH - High-Level Output Voltage - V The TLV2262 and TLV2264 are dual and quad low voltage operational amplifiers from Texas Instruments. Both devices exhibit rail-to-rail output performance for increased dynamic range in single or split supply applications. The TLV226x family offers a compromise between the micropower TLV225x and the ac performance of the TLC227x. It has low supply current for batterypowered applications, while still having adequate ac performance for applications that demand it. This family is fully characterized at 3 V and 5 V and is optimized for low-voltage applications. The noise performance has been dramatically improved over previous generations of CMOS amplifiers. Figure 1 depicts the low level of noise voltage for this CMOS amplifier, which has only 200 A (typ) of supply current per amplifier. HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 3 TA = - 55C 2.5 TA = 125C 2 TA = 25C 1.5 AA AA 1 0.5 TA = 85C TA = - 40C 0 The TLV226x, exhibiting high input impedance 0 500 1000 1500 2000 and low noise, are excellent for small-signal | IOH | - High-Level Output Current - A conditioning for high-impedance sources, such as Figure 1 piezoelectric transducers. Because of the micropower dissipation levels combined with 3-V operation, these devices work well in hand-held monitoring and remote-sensing applications. In addition, the rail-to-rail output feature with single or split supplies makes this family a great choice when interfacing with analog-to-digital converters (ADCs). For precision applications, the TLV226xA family is available and has a maximum input offset voltage of 950 V. The TLV2262/4 also makes great upgrades to the TLV2332/4 in standard designs. They offer increased output dynamic range, lower noise voltage and lower input offset voltage. This enhanced feature set allows them to be used in a wider range of applications. For applications that require higher output drive and wider input voltage range, see the TLV2432 and TLV2442 devices. If your design requires single amplifiers, please see the TLV2211/21/31 family. These devices are single rail-to-rail operational amplifiers in the SOT-23 package. Their small size and low power consumption, make them ideal for high density, battery-powered equipment. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Advanced LinCMOS is a trademark of Texas Instruments Incorporated. Copyright 1999, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262 AVAILABLE OPTIONS PACKAGED DEVICES VIOmax AT 25C TA SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (JG) PLASTIC DIP (P) TSSOP (PW) CERAMIC FLATPACK (U) 0C to 70C 2.5 mV TLV2262CD -- -- TLV2262CP TLV2262CPWLE -- - 40C to 85C 950 V 2.5 mV TLV2262AID TLV2262ID -- -- -- -- TLV2262AIP TLV2262IP TLV2262AIPWLE -- -- -- - 40C to 125C 950 V 2.5 mV TLV2262AQD TLV2262QD -- -- -- -- -- -- -- -- -- -- - 55C to 125C 950 V 2.5 mV -- -- TLV2262AMFK TLV2262MFK TLV2262AMJG TLV2262MJG -- -- -- -- TLV2262AMU TLV2262MU The D packages are available taped and reeled. Add R suffix to device type (e.g., TLV2262CDR). The PW package is available only left-end taped and reeled. Chips are tested at 25C. TLV2264 AVAILABLE OPTIONS PACKAGED DEVICES TA VIOmax AT 25C SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (J) PLASTIC DIP (N) TSSOP (PW) CERAMIC FLATPACK (W) - 40C to 85C 950 V 2.5 mV TLV2264AID TLV2264ID -- -- -- -- TLV2264AIN TLV2264IN TLV2264AIPWLE -- -- -- - 40C to 125C 950 V 2.5 mV TLV2264AQD TLV2264QD -- -- -- -- -- -- -- -- -- -- - 55C to 125C 950 V 2.5 mV -- -- TLV2264AMFK TLV2264MFK TLV2264AMJ TLV2264MJ -- -- -- -- TLV2264AMW TLV2264MW The D packages are available taped and reeled. Add R suffix to device type (e.g., TLV2262IDR). The PW package is available only left-end taped and reeled. Chips are tested at 25C. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262C, TLV2262AC TLV2262I, TLV2262AI TLV2262Q, TLV2262AQ D, P, OR PW PACKAGE (TOP VIEW) 1OUT 1IN - 1IN + VDD - /GND 1 8 2 7 3 6 4 5 TLV2264I, TLV2264AI TLV2264Q, TLV2264AQ D, N, OR PW PACKAGE (TOP VIEW) 1OUT 1IN - 1IN + VDD + 2IN + 2IN - 2OUT VDD + 2OUT 2IN - 2IN + TLV2262M, TLV2262AM JG PACKAGE (TOP VIEW) 1OUT 1IN - 1IN + VDD - /GND 1 8 2 7 3 6 4 5 1OUT 1IN - 1IN + VDD + 2IN + 2IN - 2OUT NC VCC + 2OUT 2IN - 2IN + 10 2 9 3 8 4 7 5 6 1IN + NC VCC + NC 2IN + NC 1OUT NC VDD+ NC 17 6 16 7 15 8 14 9 10 11 12 13 11 5 10 6 9 7 8 1 14 2 13 3 12 4 11 5 10 6 9 7 8 4OUT 4IN - 4IN + VDD - / GND 3IN + 3IN - 3OUT NC 2OUT NC 2IN - NC 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 4IN + NC VCC - /GND NC 3IN + 2IN - 2OUT NC 3OUT 3IN - 5 12 4 NC VDD- /GND NC 2IN+ NC NC 1IN - NC 1IN + NC 3 4OUT 4IN - 4IN + VDD - / GND 3IN + 3IN - 3OUT TLV2264M, TLV2264AM FK PACKAGE (TOP VIEW) TLV2262M, TLV2262AM FK PACKAGE (TOP VIEW) 3 2 1 20 19 18 4 13 1IN - 1OUT NC 4OUT 4IN - 1 14 2 TLV2264M, TLV2264AM J OR W PACKAGE (TOP VIEW) VDD + 2OUT 2IN - 2IN + TLV2662M, TLV2262AM U PACKAGE (TOP VIEW) NC 1OUT 1IN - 1IN + VCC - /GND 1 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 Q6 Q9 Q12 Q14 Q16 R6 IN + OUT C1 IN - R5 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 Q1 Q4 Q13 Q15 Q17 D1 Q2 Q5 R3 R4 Q7 Q8 Q10 Q11 R1 VDD - / GND ACTUAL DEVICE COMPONENT COUNT TLV2252 TLV2254 Transistors COMPONENT 38 76 Resistors 28 54 Diodes 9 18 Capacitors 3 6 Includes both amplifiers and all ESD, bias, and trim circuitry R2 Template Release Date: 7-11-94 Q3 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS VDD + SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 4 equivalent schematic (each amplifier) TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDD Input voltage range, VI (any input, see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDD - - 0.3 V to VDD+ Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 mA Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Total current into VDD + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Total current out of VDD - . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 mA Duration of short-circuit current (at or below) 25C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 85C Q suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40C to 125C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 55C to 125C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, P, and PW packages . . . . . . . 260C FK, J, JG, U, AND W packages . . 300C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to VDD - . 2. Differential voltages are at the noninverting input with respect to the inverting input. Excessive current flows when input is brought below VDD - - 0.3 V. 3. The output may be shorted to either supply. Temperature and /or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 85C POWER RATING TA = 125C POWER RATING D-8 725 mW 5.8 mW/C 377 mW 145 mW D-14 950 mW 7.6 mW/C 494 mW 190 mW FK 1375 mW 11.0 mW/C 715 mW 275 mW J 1375 mW 11.0 mW/C 715 mW 275 mW JG 1050 mW 8.4 mW/C -- 210 mW N 1150 mW 9.2 mW/C 598 mW -- P 1000 mW 8.0 mW/C 520 mW 200 mW PW-8 525 mW 4.2 mW/C 273 mW 105 mW PW-14 700 mW 5.6 mW/C 364 mW -- U 700 mW 5.5 mW/C -- 150 mW W 700 mW 5.5 mW/C 370 mW 150 mW recommended operating conditions I SUFFIX Supply voltage, VDD (see Note 1) Input voltage range, VI Common-mode input voltage, VIC Q SUFFIX M SUFFIX MIN MAX MIN MAX MIN MAX 2.7 8 2.7 8 2.7 8 VDD - VDD - VDD + - 1.3 VDD + - 1.3 Operating free-air temperature, TA - 40 85 NOTE 1: All voltage values, except differential voltages, are with respect to VDD - . POST OFFICE BOX 655303 UNIT V VDD - VDD - VDD + - 1.3 VDD + - 1.3 VDD - VDD - VDD + - 1.3 VDD + - 1.3 V - 40 125 - 55 125 C * DALLAS, TEXAS 75265 V 5 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262I electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER VIO Input In ut offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input In ut offset current IIB Input In ut bias current VICR VOH Common-mode input voltage range High level output High-level voltage TA TEST CONDITIONS 25C 300 2500 300 0.003 V/mo 25C 0.5 0.5 150 150 1 1 150 25C 0 to 2 Full range 0 to 1.7 - 0.3 to 2.2 150 0 to 2 - 0.3 to 2.2 IOH = - 100 A 25C 2.85 2.85 Full range 2.99 2.825 2.825 2.7 2.7 Full range 2.65 2.65 V IOL = 50 A 25C 10 10 IOL = 500 A 25C 100 100 RL = 50 k VIC = 1 1.5 5V V, VO = 1 V to 2 V RL = 1 M 150 25C 150 200 Full range 60 Full range 30 mV 200 300 25C pA A 2.99 25C Full range pA A V 0 to 1.7 25C mA V 0.003 IOH = - 20 A IOL = 1 950 1500 UNIT 25C |VIO | 5 mV VIC = 1 1.5 5V V, MAX V/C Full range VIC = 1 1.5 5V V, TYP 2 25C RS = 50 , MIN 2 Full range VIC = 1.5 V, Low-level Low level output voltage MAX 3000 25C to 85C VDD = 1.5 V, VIC = 0, VO = 0, RS = 50 TLV2262AI TYP Full range IOH = - 400 A VOL TLV2262I MIN 100 300 60 100 AVD Large-signal Large signal differential voltage am amplification lification 25C 100 100 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, P package 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25C 270 270 CMRR Common-mode rejection ratio VIC = 0 to 1.7 V, VO = 1.5 V, RS = 50 25C 65 Full range 60 kSVR Supply y voltage g rejection j ratio (VDD/VIO) VDD = 2.7 V to 8 V, VIC = VDD /2, No load 25C 80 Full range 80 IDD Supply Su ly current VO = 1 1.5 5V V, No load 25C Full range 30 75 65 V/mV 77 dB 60 95 80 100 dB 80 400 500 500 400 500 500 A Full range is - 40C to 85C. Referenced to 1.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262I operating characteristics at specified free-air temperature, VDD = 3 V PARAMETER TA TEST CONDITIONS VO = 1 1.1 1 V to 1 1.9 9V V, CL = 100 pF F RL = 50 k, TLV2262I MIN TYP 25C 0.35 0.55 Full range 03 0.3 TLV2262AI MAX MIN TYP 0.35 0.55 MAX UNIT SR Slew rate at unity gain Vn Equivalent input noise q voltage f = 10 Hz 25C 43 43 f = 1 kHz 25C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.6 0.6 VN(PP) f = 0.1 Hz to 10 Hz 25C 1 1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz, kHz RL = 50 k AV = 1 0.03% 0.03% THD + N 0.05% 0.05% Gain-bandwidth product f = 1 kHz,, CL = 100 pF RL = 50 k, 25C 0 67 0.67 0 67 0.67 MHz Maximum output swing output-swing bandwidth VO(PP) = 1 V,, RL = 50 k, AV = 1,, CL = 100 pF 25C 395 395 kHz To 0.1% 0 1% 56 5.6 56 5.6 Settling time AV = - 1, Step = 1 V to 2 V,, RL = 50 k, CL = 100 pF 12 5 12.5 12 5 12.5 RL = 50 k, CL = 100 pF 25C 55 55 25C 11 11 BOM ts m Phase margin at unity gain V/s 03 0.3 fA /Hz s 25C To 0 0.01% 01% POST OFFICE BOX 655303 V 25C AV = 10 Gain margin Full range is - 40C to 85C. Referenced to 1.5 V nV/Hz * DALLAS, TEXAS 75265 dB 7 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range TA TEST CONDITIONS 25C High-level output voltage |VIO | 5 mV mV, VIC = 2 2.5 5V V, Large signal differential Large-signal lification voltage am amplification IOL = 500 A IOL = 1 mA RL = 50 k VIC = 2 2.5 5V V, VO = 1 V to 4 V RL = 1 M 300 MAX 950 1500 UNIT V V/C 25C 0.003 0.003 V/mo 25C 0.5 0.5 150 150 1 1 150 25C 0 to 4 Full range g 0 to 3.5 25C IOL = 50 A TYP 2 RS = 50 IOH = - 100 A MIN 2 25C 5V VIC = 2 2.5 V, AVD 2500 Full range VIC = 2.5 V, Low-level output voltage 300 Full range IOH = - 400 A VOL MAX 3000 25C to 85C VDD = 2.5 V, VIC = 0, VO = 0, RS = 50 TLV2262AI TYP Full range IOH = - 20 A VOH TLV2262I MIN - 0.3 to 4.2 150 0 to 4 4.85 Full range 4.82 25C 4.7 Full range 4.6 V 4.99 4.94 4.85 4.94 V 4.82 4.85 4.7 4.85 4.6 25C 0.01 25C 0.09 Full range 0.01 0.15 0.09 0.15 25C 0.2 Full range 80 Full range 55 170 0.15 0.15 0.3 0.2 0.3 25C pA - 0.3 to 4.2 0 to 3.5 4.99 25C pA V 0.3 0.3 80 170 55 V/mV 25C 550 550 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, P package 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25C 240 240 CMRR Common-mode rejection j ratio VIC = 0 to 2.7 V, VO = 2.5 V, RS = 50 25C 70 Full range 70 kSVR Supply y voltage g rejection j ratio (VDD /VIO) VDD = 4.4 V to 8 V, VIC = VDD /2, No load 25C 80 Full range 80 IDD Supply current 5V VO = 2 2.5 V, No load 25C Full range 83 70 83 dB 70 95 80 95 dB 80 400 500 500 400 500 500 A Full range is - 40C to 85C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262I operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS RL = 50 k, TA TLV2262I MIN TYP 25C 0.35 0.55 Full range 03 0.3 TLV2262AI MAX MIN TYP 0.35 0.55 SR Slew rate at unity gain VO = 1 1.5 5 V to 3 3.5 5V V, CL = 100 pF F Vn Equivalent input q noise voltage f = 10 Hz 25C 40 40 f = 1 kHz 25C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.3 1.3 In Equivalent input noise current 25C 0.6 0.6 THD + N Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz kHz, RL = 50 k AV = 1 Gain-bandwidth product f = 50 kHz,, CL = 100 pF RL = 50 k, Maximum outputswing bandwidth VO(PP) = 2 V,, RL = 50 k, AV = 1,, CL = 100 pF To 0.1% 0 1% Settling time AV = - 1, Step = 0.5 V to 2.5 V,, RL = 50 k, CL = 100 pF RL = 50 k, CL = 100 pF BOM ts m Phase margin at unity gain V/s 03 0.3 nV/Hz V fA /Hz 0.017% 0.017% 0.03% 0.03% 25C 0 71 0.71 0 71 0.71 MHz 25C 185 185 kHz 64 6.4 64 6.4 14 1 14.1 14 1 14.1 25C 56 56 25C 11 11 s 25C 01% To 0 0.01% POST OFFICE BOX 655303 UNIT 25C AV = 10 Gain margin Full range is - 40C to 85C. Referenced to 2.5 V MAX * DALLAS, TEXAS 75265 dB 9 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2264I electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR VOH Common-mode input voltage range High level output High-level voltage TEST CONDITIONS 25C Large signal differential Large-signal lification voltage am amplification 300 2500 MIN 300 0.003 0.003 V/mo 25C 0.5 0.5 150 150 1 1 150 25C 0 to 2 Full range g 0 to 1.7 - 0.3 to 2.2 150 0 to 2 IOH = - 100 A 25C 2.85 2.85 Full range 2.825 2.825 25C 2.7 2.7 Full range 2.65 VIC = 1.5 1 5 V, V VO = 1 to 2 V mA 2.99 pA V 2.99 V 2.65 25C 10 10 25C 100 100 Full range 150 25C pA - 0.3 to 2.2 0 to 1.7 25C IOL = 1 V 25C IOH = - 20 A IOL = 500 A 950 1500 UNIT V/C |VIO | 5 mV VIC = 1 1.5 5V V, MAX 2 25C IOL = 50 A TYP 2 Full range 5V VIC = 1 1.5 V, AVD MAX Full range RS = 50 , TLV2264AI TYP 3000 25C to 85C VDD = 1 1.5 5 V, V VIC = 0, VO = 0, RS= 50 VIC = 1.5 V, Low-level output voltage TLV2264I MIN Full range IOH = - 400 A VOL TA 150 200 Full range mV 200 300 100 300 RL = 50 k 25C 60 60 100 Full range 30 RL = 1 M 25C 100 100 30 V/mV ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25C 270 270 CMRR Common-mode rejection ratio VIC = 0 to 1.7 V, VO = 1.5 V, RS = 50 25C 65 Full range 60 kSVR Supply voltage rejection ratio (VDD /VIO) VDD = 2.7 V to 8 V, VIC = VDD /2, No load 25C Full range 80 80 IDD Supply y current (four amplifiers) VO = 1.5 1 5 V, V No load 25C Full range 75 65 77 dB 60 95 0.8 80 80 1 1 100 0.8 dB 1 1 mA Full range is - 40C to 85C. Referenced to 1.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2264I operating characteristics at specified free-air temperature, VDD = 3 V PARAMETER TEST CONDITIONS RL = 50 k, TA TLV2264I MIN TYP 25C 0 35 0.35 0 55 0.55 Full range 03 0.3 TLV2264AI MAX MIN TYP 0 35 0.35 0 55 0.55 MAX UNIT Slew rate at unity gain 7 V to 1 7V VO = 0 0.7 1.7 V, CL = 100 pF F Vn Equivalent q input noise voltage f = 10 Hz 25C 43 43 f = 1 kHz 25C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.6 0.6 VN(PP) f = 0.1 Hz to 10 Hz 25C 1 1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz, kHz RL = 50 k AV = 1 0.03% 0.03% THD + N 0.05% 0.05% Gain-bandwidth product f = 1 kHz,, CL = 100 pF RL = 50 k , 25C 0 67 0.67 0 67 0.67 MHz Maximum output swing output-swing bandwidth VO(PP) = 1 V,, RL = 50 k , AV = 1,, CL = 100 pF 25C 395 395 kHz To 0.1% 0 1% 56 5.6 56 5.6 Settling time AV = -1, 1, Step = 1 V to 2 V,, RL = 50 k , CL = 100 pF 12 5 12.5 12 5 12.5 RL = 50 k, CL = 100 pF 25C 55 55 25C 11 11 SR BOM ts m Phase margin at unity gain V/s 03 0.3 fA /Hz s 25C To 0 0.01% 01% POST OFFICE BOX 655303 V 25C AV = 10 Gain margin Full range is - 40C to 85C. Referenced to 1.5 V nV/Hz * DALLAS, TEXAS 75265 dB 11 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2264I electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR VOH Common-mode input voltage range High level output High-level voltage TA TEST CONDITIONS 25C Large signal differential Large-signal lification voltage am amplification 2500 0.003 V/mo 25C 0.5 1 150 25C 0 to 4 Full range g 0 to 3.5 25C 4.85 4.82 25C 4.7 Full range 4.6 RL = 50 k VIC = 2.5 25V V, VO = 1 V to 4 V RL = 1 M 150 1 Full range mA 0.5 150 IOH = - 100 A IOL = 1 V 0.003 25C IOL = 500 A 950 1500 UNIT 25C IOH = - 20 A VIC = 2 2.5 5V V, 300 MAX V/C RS = 50 IOL = 50 A TYP 2 25C |VIO | 5 mV mV, MIN 2 Full range 5V VIC = 2 2.5 V, AVD 300 Full range VIC = 2.5 V, Low-level Low level output voltage MAX 3000 25C to 85C VDD = 2 2.5 5 V, V VIC = 0, VO = 0, RS = 50 TLV2264AI TYP Full range IOH = - 400 A VOL TLV2264I MIN - 0.3 to 4.2 150 0 to 4 - 0.3 to 4.2 4.99 4.94 4.85 4.94 4.82 4.85 4.7 V 4.85 4.6 25C 0.01 25C 0.09 Full range 0.01 0.15 0.09 0.15 25C 0.2 Full range 80 Full range 55 170 0.15 0.15 0.3 0.2 0.3 25C pA V 0 to 3.5 4.99 pA V 0.3 0.3 80 170 55 V/mV 25C 550 550 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25C 240 240 CMRR Common-mode rejection j ratio VIC = 0 to 2.7 V, VO = 2.5 V, RS = 50 25C 70 Full range 70 kSVR Supply y voltage g rejection j ratio (VDD /VIO) VDD = 4.4 V to 8 V, VIC = VDD /2, No load 25C 80 Full range 80 IDD Supply y current (four amplifiers) VO = 2.5 2 5 V, V No load 25C Full range 83 70 83 dB 70 95 80 95 dB 80 0.8 1 1 0.8 1 1 mA Full range is - 40C to 85C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2264I operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS RL = 50 k , TA TLV2264I MIN TYP 25C 0 35 0.35 0 55 0.55 Full range 03 0.3 TLV2264AI MAX MIN TYP 0 35 0.35 0 55 0.55 MAX UNIT Slew rate at unity gain 4 V to 2 6V VO = 1 1.4 2.6 V, CL = 100 pF F Vn Equivalent q input noise voltage f = 10 Hz 25C 40 40 f = 1 kHz 25C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.3 1.3 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz, kHz RL = 50 k AV = 1 0.017% 0.017% THD + N 0.03% 0.03% Gain-bandwidth product f = 50 kHz,, CL = 100 pF RL = 50 k , 25C 0 71 0.71 0 71 0.71 MHz Maximum outputswing bandwidth VO(PP) = 2 V,, RL = 50 k , AV = 1,, CL = 100 pF 25C 185 185 kHz To 0.1% 0 1% 64 6.4 64 6.4 Settling time AV = - 1, Step = 0.5 V to 2.5 V,, RL = 50 k , CL = 100 pF 14 1 14.1 14 1 14.1 RL = 50 k , CL = 100 pF 25C 56 56 25C 11 11 SR BOM ts m Phase margin at unity gain V/s 03 0.3 fA /Hz s 25C 01% To 0 0.01% POST OFFICE BOX 655303 V 25C AV = 10 Gain margin Full range is - 40C to 85C. Referenced to 2.5 V nV/Hz * DALLAS, TEXAS 75265 dB 13 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262Q and TLV2262M electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER TA TEST CONDITIONS TLV2262Q, TLV2262M MIN VIO Input In ut offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input In ut offset current IIB Input In ut bias current VICR VOH Common-mode input voltage range High level output High-level voltage 25C Low-level Low level output voltage Large signal differential Large-signal voltage am amplification lification 300 2500 300 0.003 V/mo 25C 0.5 0.5 500 500 1 1 500 25C 0 to 2 Full range 0 to 1.7 - 0.3 to 2.2 500 0 to 2 IOH = - 100 A 25C 2.85 2.85 Full range 2.82 2.82 25C 2.7 2.7 Full range 2.55 IOL = 1 mA RL = 50 k VIC = 1 1.5 5V V, VO = 1 V to 2 V RL = 1 M - 0.3 to 2.2 2.99 10 25C 100 Full range 200 Full range V 10 150 100 Full range 25 100 150 165 300 200 300 60 V 2.99 165 25C pA A 2.55 25C 25C pA A 0 to 1.7 25C IOL = 500 A V 0.003 IOH = - 20 A VIC = 1 1.5 5V V, 950 1500 25C |VIO | 5 mV IOL = 50 A UNIT MAX V/C 25C VIC = 1.5 V, TYP 2 125C RS = 50 , MIN 2 125C VIC = 1 1.5 5V V, AVD MAX 3000 25C to 125C IOH = - 400 A VOL TYP Full range VDD = 1.5 V, VIC = 0, VO = 0, RS = 50 TLV2262AQ, TLV2262AM mV 300 300 60 100 25 V/mV 25C 100 100 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, P package 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25C 270 270 CMRR Common-mode rejection ratio VIC = 0 to 1.7 V, VO = 1.5 V, RS = 50 25C 65 Full range 60 kSVR Supply y voltage g rejection j ratio (VDD /VIO) VDD = 2.7 V to 8 V, VIC = VDD /2, No load 25C 80 Full range 80 75 65 77 60 95 80 80 100 dB dB Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 1.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 14 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262Q and TLV2262M electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) (continued) PARAMETER TA TEST CONDITIONS TLV2262Q, TLV2262M MIN IDD Supply Su ly current 1 5 V, V VO = 1.5 No load 25C TLV2262AQ, TLV2262AM TYP MAX 400 500 Full range MIN UNIT TYP MAX 400 500 500 500 A Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. TLV2262Q and TLV2262M operating characteristics at specified free-air temperature, VDD = 3 V PARAMETER SR Slew rate at unity gain VO = 0 0.5 5 V to 1 1.7 7V V, CL = 100 pF F TLV2262Q, TLV2262M TA TEST CONDITIONS RL = 50 k, MIN TYP 25C 0.35 0.55 Full range 0 25 0.25 MAX TLV2262AQ, TLV2262AM MIN TYP 0.35 0.55 UNIT MAX V/s 0 25 0.25 Vn Equivalent q input noise voltage f = 10 Hz 25C 43 43 f = 1 kHz 25C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.6 0.6 VN(PP) f = 0.1 Hz to 10 Hz 25C 1 1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise 0.03% 0.03% THD + N 0.05% 0.05% 25C 0 67 0.67 0 67 0.67 MHz 25C 395 395 kHz 56 5.6 56 5.6 12 5 12.5 12 5 12.5 25C 55 55 Gain margin 25C Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 1.5 V 11 11 VO = 0.5 V to 2.5 V, f = 20 kHz, kHz RL = 50 k AV = 1 Gain-bandwidth product f = 1 kHz,, CL = 100 pF RL = 50 k, BOM Maximum output swing output-swing bandwidth VO(PP) = 1 V,, RL = 50 k, AV = 1,, CL = 100 pF Settling time AV = - 1, Step = 1 V to 2 V,, RL = 50 k, CL = 100 pF To 0.1% 0 1% ts RL = 50 k, CL = 100 pF m Phase margin at unity gain V fA /Hz 25C AV = 10 s 25C To 0 0.01% 01% POST OFFICE BOX 655303 nV/Hz * DALLAS, TEXAS 75265 dB 15 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262Q and TLV2262M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TLV2262Q, TLV2262M TA TEST CONDITIONS MIN VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range 25C High-level output voltage Low-level output voltage Large-signal L i l diff differential ti l voltage am lification amplification 2500 IOL = 50 A VIC = 2 2.5 5V V, IOL = 500 A IOL = 1 mA RL = 50 k VIC = 2.5 2 5 V, V VO = 1 V to 4 V RL = 1 M 950 1500 V 25C 0.003 0.003 V/mo 25C 0.5 0.5 500 500 1 1 500 25C 0 to 4 Full range g 0 to 3.5 25C VIC = 2.5 V, 300 UNIT MAX V/C RS = 50 IOH = - 100 A TYP 2 25C |VIO | 5 mV mV, MIN 2 125C 5V VIC = 2 2.5 V, AVD 300 125C IOH = - 400 A VOL MAX 3000 25C to 125C IOH = - 20 A VOH TYP Full range VDD = 2.5 V, VIC = 0, VO = 0, RS = 50 TLV2262AQ, TLV2262AM - 0.3 to 4.2 500 0 to 4 4.85 Full range 4.82 25C 4.7 Full range 4.5 V 4.99 4.94 4.85 4.94 4.82 4.85 4.7 V 4.85 4.5 25C 0.01 25C 0.09 Full range 0.01 0.15 0.09 0.15 25C 0.2 Full range 80 Full range 50 25C 170 0.15 0.15 0.3 0.2 0.3 25C pA - 0.3 to 4.2 0 to 3.5 4.99 25C pA V 0.3 0.3 80 170 50 V/mV ri(d) Differential input resistance 25C 550 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, P package 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25C 240 240 CMRR Common-mode rejection j ratio VIC = 0 to 2.7 V, VO = 2.5 V, RS = 50 kSVR Supply y voltage g rejection j ratio (VDD /VIO) VDD = 4.4 V to 8 V, VIC = VDD /2, No load 25C 70 Full range 70 25C 80 Full range 80 83 70 550 1012 83 70 95 80 80 95 dB dB Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 16 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2262Q and TLV2262M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) (continued) PARAMETER TEST CONDITIONS TLV2262Q, TLV2262M TA MIN IDD Supply current 25V VO = 2.5 V, No load 25C TLV2262AQ, TLV2262AM TYP MAX 400 500 Full range MIN UNIT TYP MAX 400 500 500 500 A Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. TLV2262Q and TLV2262M operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS RL = 50 k TLV2262Q, TLV2262M TA MIN TYP 25C 0.35 0.55 Full range 0 25 0.25 TLV2262AQ, TLV2262AM MAX MIN TYP 0.35 0.55 SR Slew rate at unity gain 5 V to 3 5V VO = 0 0.5 3.5 V, CL = 100 pF F Vn Equivalent q input noise voltage f = 10 Hz 25C 40 40 f = 1 kHz 25C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.3 1.3 In Equivalent input noise current 25C 0.6 0.6 THD + N Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz kHz, RL = 50 k AV = 1 Gain-bandwidth product f = 50 kHz,, CL = 100 pF RL = 50 k, Maximum output swing output-swing bandwidth VO(PP) = 2 V,, RL = 50 k, AV = 1,, CL = 100 pF To 0.1% 0 1% Settling time AV = - 1, Step = 0.5 V to 2.5 V,, RL = 50 k, CL = 100 pF RL = 50 k, CL = 100 pF UNIT MAX V/s 0 25 0.25 nV/Hz V fA /Hz 0.017% 0.017% 0.03% 0.03% 25C 0 71 0.71 0 71 0.71 MHz 25C 185 185 kHz 64 6.4 64 6.4 14 1 14.1 14 1 14.1 25C 56 56 Gain margin 25C Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 2.5 V 11 11 BOM ts m Phase margin at unity gain 25C AV = 10 s 25C To 0 0.01% 01% POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 dB 17 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2264Q and TLV2264M electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) PARAMETER TA TEST CONDITIONS TLV2264Q, TLV2264M MIN VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range 25C High level output High-level voltage RS = 50 , VIC = 1 1.5 5V V, Large signal differential Large-signal voltage am amplification lification IOL = 500 A IOL = 1 mA RL = 50 k VIC = 1.5 15V V, VO = 1 V to 2 V RL = 1 M 300 UNIT MAX 950 1500 V V/C 25C 0.003 0.003 V/mo 25C 0.5 0.5 500 500 1 1 500 25C 0 to 2 Full range g 0 to 1.7 25C IOL = 50 A TYP 2 |VIO | 5 mV IOH = - 100 A MIN 2 25C VIC = 1 1.5 5V V, AVD 2500 125C VIC = 1.5 V, Low-level Low level output voltage 300 125C IOH = - 400 A VOL MAX 3000 25C to 125C IOH = - 20 A VOH TYP Full range 5 V, V VDD = 1 1.5 VIC = 0, VO = 0, RS = 50 TLV2264AQ, TLV2264AM - 0.3 to 2.2 500 0 to 2 V 2.99 25C 2.85 2.85 Full range 2.82 2.82 25C 2.7 2.7 Full range 2.6 V 2.6 25C 10 25C 100 Full range 10 150 100 150 25C 200 Full range 60 Full range 25 100 150 150 300 200 300 25C pA - 0.3 to 2.2 0 to 1.7 2.99 pA mV 300 300 60 100 25 V/mV 25C 100 100 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25C 270 270 CMRR Common-mode rejection j ratio VIC = 0 to 1.7 V, VO = 1.5 V, RS = 50 25C 65 Full range 60 kSVR Supply y voltage g rejection j ratio (VDD /VIO) VDD = 2.7 V to 8 V, VIC = VDD /2, No load 25C 80 Full range 80 75 65 77 60 95 80 80 100 dB dB Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 1.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 18 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2264Q and TLV2264M electrical characteristics at specified free-air temperature, VDD = 3 V (unless otherwise noted) (continued) PARAMETER TEST CONDITIONS TLV2264Q, TLV2264M TA MIN Supplyy current ((four amplifiers) IDD 15V VO = 1.5 V, No load 25C TLV2264AQ, TLV2264AM TYP MAX 0.8 1 Full range MIN UNIT TYP MAX 0.8 1 1 1 mA Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. TLV2264Q and TLV2264M operating characteristics at specified free-air temperature, VDD = 3 V PARAMETER TEST CONDITIONS RL = 50 k, TLV2264Q, TLV2264M TA MIN TYP 25C 0 35 0.35 0 55 0.55 Full range 0 25 0.25 TLV2264AQ, TLV2264AM MAX MIN TYP 0 35 0.35 0 55 0.55 UNIT MAX Slew rate at unity gain 5 V to 1 7V VO = 0 0.5 1.7 V, CL = 100 pF F Vn Equivalent q input noise voltage f = 10 Hz 25C 43 43 f = 1 kHz 25C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.6 0.6 VN(PP) f = 0.1 Hz to 10 Hz 25C 1 1 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise 0.03% 0.03% THD + N 0.05% 0.05% 25C 0 67 0.67 0 67 0.67 MHz 25C 395 395 kHz 56 5.6 56 5.6 12 5 12.5 12 5 12.5 25C 55 55 Gain margin 25C Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 1.5 V 11 11 SR BOM ts m VO = 0.5 V to 2.5 V, f = 20 kHz, kHz RL = 50 k AV = 1 Gain-bandwidth product f = 1 kHz,, CL = 100 pF RL = 50 k , Maximum outputswing bandwidth VO(PP) = 1 V,, RL = 50 k, AV = 1,, CL = 100 pF To 0.1% 0 1% Settling time AV = - 1, Step = 1 V to 2 V,, RL = 50 k , CL = 100 pF RL = 50 k, CL = 100 pF Phase margin at unity gain V/s 0 25 0.25 V fA /Hz 25C AV = 10 s 25C 01% To 0 0.01% POST OFFICE BOX 655303 nV/Hz * DALLAS, TEXAS 75265 dB 19 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2264Q and TLV2264M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TLV2264Q, TLV2264M TA TEST CONDITIONS MIN VIO Input offset voltage VIO Temperature coefficient of input offset voltage Input offset voltage long-term drift (see Note 4) IIO Input offset current IIB Input bias current VICR Common-mode input voltage range 25C High-level output voltage |VIO | 5 mV mV, VIC = 2 2.5 5V V, Large-signal Large signal differential lification voltage am amplification IOL = 500 A IOL = 1 mA RL = 50 k VIC = 2 2.5 5V V, VO = 1 V to 4 V RL = 1 M 300 UNIT MAX 950 1500 V V/C 25C 0.003 0.003 V/mo 25C 0.5 0.5 500 500 1 1 500 25C 0 to 4 Full range g 0 to 3.5 25C IOL = 50 A TYP 2 RS = 50 IOH = - 100 A MIN 2 25C VIC = 2 2.5 5V V, AVD 2500 125C VIC = 2.5 V, Low-level output voltage 300 125C IOH = - 400 A VOL MAX 3000 25C to 125C IOH = - 20 A VOH TYP Full range 5V VDD = 2 2.5 V, VIC = 0, VO = 0, RS = 50 TLV2264AQ, TLV2264AM - 0.3 to 4.2 500 0 to 4 4.85 Full range 4.82 25C 4.7 Full range 4.5 4.99 4.94 4.85 4.94 4.82 4.85 4.7 V 4.85 4.5 25C 0.01 25C 0.09 Full range 0.01 0.15 0.09 0.15 25C 0.2 Full range 25C 80 50 170 0.15 0.15 0.3 0.2 0.3 Full range pA V 0 to 3.5 4.99 25C - 0.3 to 4.2 pA V 0.3 0.3 80 170 50 V/mV 25C 550 550 ri(d) Differential input resistance 25C 1012 1012 ri(c) Common-mode input resistance 25C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25C 240 240 CMRR Common-mode rejection j ratio VIC = 0 to 2.7 V, VO = 2.5 V, RS = 50 kSVR Supply y voltage g rejection j ratio (VDD /VIO) VDD = 4.4 V to 8 V, VIC = VDD /2, No load 25C 70 Full range 70 25C 80 Full range 80 83 70 83 70 95 80 80 95 dB dB Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150C extrapolated to TA = 25C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 20 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TLV2264Q and TLV2264M electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) (continued) PARAMETER TEST CONDITIONS TLV2264Q, TLV2264M TA MIN Supplyy current ((four amplifiers) IDD 25V VO = 2.5 V, No load 25C TLV2264AQ, TLV2264AM TYP MAX 0.8 1 Full range MIN UNIT TYP MAX 0.8 1 1 1 mA Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. TLV2264Q and TLV2264M operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS RL = 50 k , TLV2264Q, TLV2264M TA MIN TYP 25C 0 35 0.35 0 55 0.55 Full range 0 25 0.25 TLV2264AQ, TLV2264AM MAX MIN TYP 0 35 0.35 0 55 0.55 UNIT MAX Slew rate at unity gain 5 V to 3 5V VO = 0 0.5 3.5 V, CL = 100 pF F Vn Equivalent q input noise voltage f = 10 Hz 25C 40 40 f = 1 kHz 25C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25C 1.3 1.3 In Equivalent input noise current 25C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz kHz, RL = 50 k AV = 1 0.017% 0.017% THD + N 0.03% 0.03% Gain-bandwidth product f = 50 kHz,, CL = 100 pF RL = 50 k , 25C 0 71 0.71 0 71 0.71 MHz Maximum output swing output-swing bandwidth VO(PP) = 2 V,, RL = 50 k , AV = 1,, CL = 100 pF 25C 185 185 kHz To 0.1% 0 1% 64 6.4 64 6.4 Settling time AV = - 1, Step = 0.5 V to 2.5 V,, RL = 50 k , CL = 100 pF 14 1 14.1 14 1 14.1 RL = 50 k , CL = 100 pF 25C 56 56 Gain margin 25C Full range is - 40C to 125C for Q level part, - 55C to 125C for M level part. Referenced to 2.5 V 11 11 SR BOM ts m Phase margin at unity gain V/s 0 25 0.25 V fA /Hz 25C AV = 10 s 25C To 0.01% 0 01% POST OFFICE BOX 655303 nV/Hz * DALLAS, TEXAS 75265 dB 21 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO Input offset voltage Distribution vs Common-mode voltage 2-5 6, 7 VIO IIB/IIO Input offset voltage temperature coefficient Distribution 8 - 11 Input bias and input offset currents vs Free-air temperature 12 VI Input voltage vs Supply y voltage g vs Free-air temperature 13 14 VOH VOL High-level output voltage vs High-level output current 15, 18 Low-level output voltage vs Low-level output current 16, 17, 19 VO(PP) Maximum peak-to-peak output voltage vs Frequency 20 IOS Short circuit output current Short-circuit vs Supply y voltage g vs Free-air temperature 21 22 VID AVD Differential input voltage vs Output voltage Differential voltage amplification vs Load resistance AVD Large signal differential voltage amplification Large-signal vs Frequency q y vs Free-air temperature 26,, 27 28, 29 zo Output impedance vs Frequency 30, 31 CMRR Common mode rejection ratio Common-mode vs Frequency q y vs Free-air temperature 32 33 kSVR Supply voltage rejection ratio Supply-voltage vs Frequency q y vs Free-air temperature 34,, 35 36, 37 IDD Supply current vs Free-air temperature 38, 39 SR Slew rate vs Load capacitance vs Free-air temperature 40 41 VO VO Inverting large-signal pulse response 42, 43 Voltage-follower large-signal pulse response 44, 45 VO VO Inverting small-signal pulse response 46, 47 Vn Equivalent input noise voltage vs Frequency Input noise voltage Over a 10-second period 52 Integrated noise voltage vs Frequency 53 Total harmonic distortion plus noise vs Frequency 54 Gain bandwidth product Gain-bandwidth vs Supply y voltage g vs Free-air temperature 55 56 Phase margin vs Frequency q y vs Load capacitance 26,, 27 57 Gain margin vs Load capacitance 58 Unity-gain bandwidth vs Load capacitance 59 Overestimation of phase margin vs Load capacitance 60 THD + N m B1 22 Voltage-follower small-signal pulse response POST OFFICE BOX 655303 23, 24 25 48, 49 * DALLAS, TEXAS 75265 50, 51 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLV2262 INPUT OFFSET VOLTAGE DISTRIBUTION OF TLV2262 INPUT OFFSET VOLTAGE 15 12 841 Amplifiers From 2 Wafer Lots VDD = 1.5 V TA = 25C Precentage of Amplifiers - % Precentage of Amplifiers - % 15 9 6 3 0 - 1.6 - 0.8 0 0.8 VIO - Input Offset Voltage - mV 12 841 Amplifiers From 2 Wafer Lots VDD = 2.5 V TA = 25C 9 6 3 0 - 1.6 1.6 Figure 2 20 16 Percentage of Amplifiers - % Percentage of Amplifiers - % DISTRIBUTION OF TLV2264 INPUT OFFSET VOLTAGE 2272 Amplifiers From 2 Wafer Lots VDD = 1.5 V TA = 25C 12 8 4 0 - 1.6 1.6 Figure 3 DISTRIBUTION OF TLV2264 INPUT OFFSET VOLTAGE 20 - 0.8 0 0.8 VIO - Input Offset Voltage - mV - 0.8 0 0.8 VIO - Input Offset Voltage - mV 1.6 2272 Amplifiers From 2 Wafer Lots VDD = 2.5 V TA = 25C 16 12 8 4 0 - 1.6 Figure 4 - 0.8 0 0.8 VIO - Input Offset Voltage - mV 1.6 Figure 5 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE 1 1 VIO - Input Offset Voltage - mV VIO - Input Offset Voltage - mV VDD = 3 V RS = 50 TA = 25C 0.5 0 AA AA AA AA - 0.5 -1 -1 - 0.5 0 0.5 1 1.5 2 2.5 VDD = 5 V RS = 50 TA = 25C 0.5 0 - 0.5 -1 -1 3 VIC - Common-Mode Input Voltage - V 0 Figure 6 3 4 30 Percentage of Amplifiers - % 128 Amplifiers From 2 Wafer Lots VDD = 1.5 V 25 P Package TA = 25C to 85C 20 15 10 128 Amplifiers From 2 Wafer Lots VDD = 2.5 V 25 P Package TA = 25C to 85C 20 15 10 5 5 -4 -3 -2 -1 0 1 2 3 4 VIO - Temperature Coefficient - V / C 5 0 -5 -4 -3 -2 -1 0 1 2 3 4 VIO - Temperature Coefficient - V / C Figure 8 Figure 9 For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. 24 5 DISTRIBUTION OF TLV2262 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 30 Percentage of Amplifiers - % 2 Figure 7 DISTRIBUTION OF TLV2262 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 0 -5 1 VIC - Common-Mode Input Voltage - V POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLV2264 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT DISTRIBUTION OF TLV2264 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 35 128 Amplifiers From 2 Wafer Lots 30 VDD = 1.5 V N Package TA = 25C to 125C 25 128 Amplifiers From 2 Wafer Lots VDD = 2.5 V N Package TA = 25C to 125C 30 Percentage of Amplifiers - % Percentage of Amplifiers - % 35 20 15 10 5 25 20 15 10 5 0 -5 -4 -3 -2 -1 0 1 2 3 4 0 5 -5 -4 -3 -2 -1 0 1 2 3 VIO - Temperature Coefficient of Input Offset Voltage - V / C VIO - Temperature Coefficient of Input Offset Voltage - V / C AA AA INPUT BIAS AND INPUT OFFSET CURRENTS vs FREE-AIR TEMPERATURE INPUT VOLTAGE vs SUPPLY VOLTAGE 35 30 5 Figure 11 2.5 VDD = 2.5 V VIC = 0 VO = 0 RS = 50 RS = 50 TA = 25C 2 1.5 25 IIB 20 15 IIO 10 VI - Input Voltage - V IIO - Input Bias and Input Offset Currents - pA IIIB IB and IIO Figure 10 4 1 0.5 0 | VIO | 5 mV AA AA - 0.5 -1 - 1.5 5 -2 0 25 45 65 85 105 TA - Free-Air Temperature - C 125 - 2.5 1 1.5 Figure 12 2 2.5 3 3.5 | VDD | - Supply Voltage - V 4 Figure 13 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 25 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS INPUT VOLTAGE vs FREE-AIR TEMPERATURE HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 5 4 VDD = 5 V VDD = 3 V 3.5 VOH - High-Level Output Voltage - V 4 VI - Input Voltage - V 3 | VIO | 5 mV 2 AA 1 0 -1 - 55 - 35 - 15 5 25 45 65 85 105 125 TA - Free-Air Temperature - C AA AA AA 3 TA = - 55C 2.5 TA = 125C 2 TA = 25C 1.5 TA = 85C 1 TA = - 40C 0.5 0 0 500 Figure 14 VOL - Low-Level Output Voltage - V VOL - Low-Level Output Voltage - V 1.4 VDD = 3 V TA = 25C VIC = 0 0.8 VIC = 0.75 V 0.6 VIC = 1.5 V 0.4 AA AA AA 0.2 0 0 1 2 3 4 IOL - Low-Level Output Current - mA 5 VDD = 3 V VIC = 1.5 V 1.2 TA = 125C 1 TA = 85C 0.8 TA = 25C 0.6 TA = - 55C 0.4 TA = - 40C 0.2 0 0 Figure 16 1 2 3 4 IOL - Low-Level Output Current - mA Figure 17 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. 26 2000 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 1 AA AA 1500 Figure 15 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 1.2 1000 | IOH | - High-Level Output Current - A POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 6 1.4 VDD = 5 V VIC = 2.5 V AA AA 1.2 5 VOL - Low-Level Output Voltage - V VOH - High-Level Output Voltage - V VDD = 5 V TA = - 55C 4 TA = - 40C 3 TA = 25C TA = 125C 2 TA = 85C 0 500 TA = 85C 0.8 TA = 25C 0.6 TA = 125C 1000 1500 2000 2500 3000 TA = - 40C 0.2 0 0 | IOH | - High-Level Output Current - A 4 5 1 2 3 IOL - Low-Level Output Current - mA Figure 18 SHORT-CIRCUIT OUTPUT CURRENT vs SUPPLY VOLTAGE 5 12 RI = 10 k TA = 25C VDD = 5 V I OS - Short-Circuit Output Current - mA VO(PP) - Maximum Peak-to-Peak Output Voltage - V 6 Figure 19 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY AA AA AA TA = - 55C 0.4 AA AA 1 0 1 4 3 VDD = 3 V 2 1 0 10 3 10 4 10 5 f - Frequency - Hz 10 6 VIC = VDD/2 TA = 25C 10 VID = - 100 mV 8 6 4 2 0 VID = 100 mV -2 2 Figure 20 3 4 5 6 VDD - Supply Voltage - V 7 8 Figure 21 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 27 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS SHORT-CIRCUIT OUTPUT CURRENT vs FREE-AIR TEMPERATURE DIFFERENTIAL INPUT VOLTAGE vs OUTPUT VOLTAGE 1000 VO = 2.5 V VDD = 5 V 10 VID = - 100 mV 8 6 4 2 0 VID = 100 mV -2 -4 - 75 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C VDD = 3 V RI = 50 k VIC = 1.5 V TA = 25C 800 V ID - Differential Input Voltage - V I OS - Short-Circuit Output Current - mA 12 600 400 200 0 - 200 - 400 - 600 - 800 - 1000 125 0 0.5 1 1.5 2 VO - Output Voltage - V Figure 22 DIFFERENTIAL VOLTAGE AMPLIFICATION vs LOAD RESISTANCE V ID - Differential Input Voltage - V AVD - Differential Voltage Amplification - V/mV 1000 VDD = 5 V VIC = 2.5 V RL = 50 k TA = 25C 600 400 200 0 - 200 - 400 - 600 - 800 - 1000 0 1 2 4 3 VO - Output Voltage - V 5 1000 VO(PP) = 2 V TA = 25C VDD = 5 V 100 AA AA VDD = 3 V 10 1 10 3 Figure 24 10 4 10 5 RL - Load Resistance - k Figure 25 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. 28 3 Figure 23 DIFFERENTIAL INPUT VOLTAGE vs OUTPUT VOLTAGE 800 2.5 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 10 6 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY 60 AVD A VD - Large-Signal Differential Voltage Amplification - dB 180 VDD = 5 V CL= 100 pF TA = 25C 135 40 Phase Margin 20 AA AA AA 90 45 Gain 0 0 - 20 om m - Phase Margin 80 - 45 - 40 103 104 105 - 90 107 106 f - Frequency - Hz Figure 26 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY 60 180 VDD = 3 V CL = 100 pF TA = 25C 135 40 Phase Margin 20 AA AA AA 90 45 Gain 0 0 - 20 om m - Phase Margin AVD A VD - Large-Signal Differential Voltage Amplification - dB 80 - 45 - 40 103 104 105 106 - 90 107 f - Frequency - Hz Figure 27 For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 29 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE 1000 10000 VDD = 5 V VIC = 2.5 V VO = 1 V to 4 V AVD - Large-Signal Differential Voltage Amplification - V/mV AVD - Large-Signal Differential Voltage Amplification - V/mV RL = 1 M RL = 50 k 100 RL = 10 k VDD = 3 V VIC = 1.5 V VO = 0.5 V to 2.5 V 10 - 75 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C RL = 1 M 1000 RL = 50 k 100 RL = 10 k 10 - 75 125 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C Figure 28 Figure 29 OUTPUT IMPEDANCE vs FREQUENCY 100 10 OUTPUT IMPEDANCE vs FREQUENCY 1000 VDD = 3 V TA = 25C A V = 100 z o - Output Impedance - z o - Output Impedance - 1000 A V = 10 AV = 1 1 0.1 10 2 10 3 10 4 f- Frequency - Hz 10 5 VDD = 5 V TA = 25C 100 A V = 100 10 A V = 10 1 AV = 1 0.1 10 2 Figure 30 10 3 10 4 f- Frequency - Hz Figure 31 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. 30 125 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 10 5 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS COMMON-MODE REJECTION RATIO vs FREQUENCY COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE 90 VDD = 5 V VIC = 2.5 V CMMR - Common-Mode Rejection Ratio - dB CMRR - Common-Mode Rejection Ratio - dB 100 TA = 25C 80 VDD = 5 V VIC = 1.5 V 60 40 20 0 10 1 10 2 10 4 10 3 f - Frequency - Hz 10 5 88 86 84 VDD = 5 V 82 80 78 VDD = 3 V 76 74 72 70 - 75 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C 10 6 Figure 32 Figure 33 SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY 100 VDD = 3 V TA = 25C k SVR - Supply-Voltage Rejection Ratio - dB k SVR - Supply-Voltage Rejection Ratio - dB 100 80 60 kSVR + 40 kSVR - 20 AA AA 0 - 20 10 1 125 10 2 10 3 10 4 f - Frequency - Hz 10 5 10 6 VDD = 5 V TA = 25C 80 60 kSVR + 40 kSVR - 20 AA AA AA 0 - 20 10 1 Figure 34 10 2 10 3 10 4 f - Frequency - Hz 10 5 10 6 Figure 35 For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 31 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS TLV2262 SUPPLY-VOLTAGE REJECTION RATIO vs FREE-AIR TEMPERATURE 110 VDD = 2.7 V to 8 V VIC = VO = VDD / 2 k SVR - Supply-Voltage Rejection Ratio - dB k SVR - Supply-Voltage Rejection Ratio - dB 110 TLV2264 SUPPLY-VOLTAGE REJECTION RATIO vs FREE-AIR TEMPERATURE 105 100 AA AA - 25 0 25 50 75 100 TA - Free-Air Temperature - C 105 100 AA AA AA 95 90 - 75 - 50 VDD = 2.7 V to 8 V VIC = VO = VDD / 2 95 90 - 75 125 - 50 TLV2264 SUPPLY CURRENT vs FREE-AIR TEMPERATURE 600 1200 500 1000 I DD - Supply Current - A I DD - Supply Current - A TLV2262 SUPPLY CURRENT vs FREE-AIR TEMPERATURE VDD = 5 V VO = 2.5 V 400 AA AA AA VDD = 3 V VO = 1.5 V 300 200 - 75 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C 125 VDD = 5 V VO = 2.5 V 800 VDD = 3 V VO = 1.5 V 600 400 - 75 - 50 Figure 38 - 25 0 25 50 75 100 TA - Free-Air Temperature - C Figure 39 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. 32 125 Figure 37 Figure 36 AA AA - 25 0 25 50 75 100 TA - Free-Air Temperature - C POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 125 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS SLEW RATE vs FREE-AIR TEMPERATURE SLEW RATE vs LOAD CAPACITANCE 1 1.2 SR - 1 SR - SR - Slew Rate - V/ s SR - Slew Rate - V/ s 0.8 0.6 SR + 0.4 0.2 SR + 0.6 0.4 0.2 VDD = 5 V AV = -1 TA = 25C 0 10 1 0.8 10 2 10 3 CL - Load Capacitance - pF 0 - 75 10 4 VDD = 5 V RL = 50 k CL = 100 pF AV = 1 - 50 - 25 0 25 50 75 100 TA - Free-Air Temperature - C Figure 40 Figure 41 INVERTING LARGE-SIGNAL PULSE RESPONSE INVERTING LARGE-SIGNAL PULSE RESPONSE 3 2 1.5 1 3 2 1 0.5 0 VDD = 5 V RL = 50 k CL = 100 pF AV = -1 TA = 25C 4 VO - Output Voltage - V VO - Output Voltage - V 5 VDD = 3 V RL = 50 k CL = 100 pF AV = -1 TA = 25C 2.5 125 0 2 4 6 8 10 12 14 t - Time - s 16 18 20 0 0 2 Figure 42 4 6 8 10 12 t - Time - s 14 16 18 20 Figure 43 For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 33 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE 3 5 VDD = 3 V RL = 50 k CL = 100 pF AV = -1 TA = 25C 4 VO - Output Voltage - V VO - Output Voltage - V 2.5 2 1.5 1 3 2 1 0.5 0 VDD = 5 V RL = 50 k CL = 100 pF AV = -1 TA = 25C 0 2 4 6 8 10 12 14 16 18 0 20 0 t - Time - s 2 4 Figure 44 16 18 0.8 0.75 0.7 VDD = 5 V RL = 50 k CL = 100 pF 2.6 A = - 1 V TA = 25C 2.55 2.5 2.45 0.65 0.6 0 2 4 6 8 10 12 14 16 18 20 t - Time - s 2.4 0 2 4 6 8 10 12 14 16 18 t - Time - s Figure 46 Figure 47 For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. 34 20 2.65 VO VO - Output Voltage - V VO - Output Voltage - V 0.85 14 INVERTING SMALL-SIGNAL PULSE RESPONSE VDD = 3 V RL = 50 k CL = 100 pF AV = - 1 TA = 25C 0.9 8 10 12 t - Time - s Figure 45 INVERTING SMALL-SIGNAL PULSE RESPONSE 0.95 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 20 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE 0.95 VDD = 5 V RL = 50 k CL = 100 pF AV = 1 TA = 25C 2.6 VO VO - Output Voltage - V 0.9 VO VO - Output Voltage - V 2.65 VDD = 3 V RL = 50 k CL = 100 pF AV = 1 TA = 25C 0.85 0.8 0.75 2.55 2.5 2.45 0.7 0 2 4 6 8 10 12 t - Time - s 14 16 18 2.4 20 0 2 4 Figure 48 14 16 18 20 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY 60 60 VDD = 3 V RS = 20 50 T = 25C A V n - Equivalent Input Noise Voltage - nV/ Hz V n - Equivalent Input Noise Voltage - nV/ Hz 8 10 12 t - Time - s Figure 49 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY 40 30 20 10 0 10 1 6 10 2 10 3 f - Frequency - Hz 10 4 VDD = 5 V RS = 20 50 T = 25C A 40 30 20 10 0 10 1 Figure 50 10 2 10 3 f - Frequency - Hz 10 4 Figure 51 For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 35 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS INTEGRATED NOISE VOLTAGE vs FREQUENCY INPUT NOISE VOLTAGE OVER A 10-SECOND PERIOD 100 1000 Calculated Using Ideal Pass-Band Filter Lower Frequency = 1 Hz TA = 25C Integrated Noise Voltage - V Input Noise Voltage - nV 750 500 250 0 - 250 - 500 - 750 - 1000 0 VDD = 5 V f = 0.1 Hz to 10 Hz TA = 25C 2 10 1 0.1 4 6 8 10 10 1 1 t - Time - s Figure 52 10 3 10 4 10 5 Figure 53 TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY GAIN-BANDWIDTH PRODUCT vs SUPPLY VOLTAGE 10 - 1 900 A V = 100 10 - 2 Gain-Bandwidth Product - kHz THD + N - Total Harmonic Distortion Plus Noise - % 10 2 f - Frequency - Hz A V = 10 AV = 1 10 - 3 10 1 VDD = 5 V RL = 50 k TA = 25C 10 2 10 3 10 4 10 4 860 820 780 740 700 0 1 f - Frequency - Hz Figure 54 2 3 5 4 6 VDD - Supply Voltage - V 7 Figure 55 For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. 36 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 8 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS PHASE MARGIN vs LOAD CAPACITANCE GAIN-BANDWIDTH PRODUCT vs FREE-AIR TEMPERATURE 75 1200 TA = 25C 60 Rnull = 100 1000 om m - Phase Margin Gain-Bandwidth Product - kHz VDD = 5 V f = 10 kHz CL = 100 pF 800 Rnull = 50 45 Rnull = 20 30 Rnull = 10 50 k 600 15 50 k VI 400 - 75 0 25 50 75 100 TA - Free-Air Temperature - C Figure 56 10 4 1000 RL = 50 k AV = 1 TA = 25C B1 - Unity-Gain Bandwidth - kHz TA = 25C Rnull = 100 15 Gain Margin - dB Rnull = 0 UNITY-GAIN BANDWIDTH vs LOAD CAPACITANCE 20 10 Rnull = 50 Rnull = 20 10 2 10 3 CL - Load Capacitance - pF 800 600 AA AA Rnull = 10 Rnull = 0 0 10 CL Figure 57 GAIN MARGIN vs LOAD CAPACITANCE 5 Rnull 10 2 10 3 CL - Load Capacitance - pF 10 125 - + VDD -/GND 0 - 50 - 25 VDD + 10 4 400 200 10 Figure 58 10 2 10 3 CL - Load Capacitance - pF 10 4 Figure 59 For all curves where VDD = 5 V, all loads are referenced to 2.5 V. For all curves where VDD = 3 V, all loads are referenced to 1.5 V. Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 37 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 TYPICAL CHARACTERISTICS OVERESTIMATION OF PHASE MARGIN vs LOAD CAPACITANCE 14 TA = 25C Overestimation of Phase Margin 12 Rnull = 100 10 8 Rnull = 50 6 4 Rnull = 10 Rnull = 20 2 0 10 10 2 10 3 CL - Load Capacitance - pF See application information Figure 60 38 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 10 4 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 APPLICATION INFORMATION driving large capacitive loads The TLV226x is designed to drive larger capacitive loads than most CMOS operational amplifiers. Figure 51 and Figure 52 illustrate its ability to drive loads greater than 400 pF while maintaining good gain and phase margins (Rnull = 0). A smaller series resistor (Rnull) at the output of the device (see Figure 61) improves the gain and phase margins when driving large capacitive loads. Figure 51 and Figure 52 show the effects of adding series resistances of 10 , 20 , 50 , and 100 . The addition of this series resistor has two effects: the first is that it adds a zero to the transfer function and the second is that it reduces the frequency of the pole associated with the output load in the transfer function. The zero introduced to the transfer function is equal to the series resistance times the load capacitance. To calculate the improvement in phase margin, equation (1) can be used. + tan-1 2 x x UGBW x Rnull x CL Where : m1 + improvement in phase margin UGBW + unity-gain bandwidth frequency R null + output series resistance C L + load capacitance m1 (1) The unity-gain bandwidth (UGBW) frequency decreases as the capacitive load increases (see Figure 53). To use equation 1, UGBW must be approximated from Figure 53. Using equation 1 alone overestimates the improvement in phase margin as illustrated in Figure 59. The overestimation is caused by the decrease in the frequency of the pole associated with the load, providing additional phase shift and reducing the overall improvement in phase margin. The pole associated with the load is reduced by the factor calculated in equation 2. F Where : F gm R null + 1 ) gm1 x R (2) null + factor reducing frequency of pole + small-signal output transconductance (typically 4.83 x 10 - 3 mhos) + output series resistance For the TLV226x, the pole associated with the load is typically 7 MHz with 100-pF load capacitance. This value varies inversely with CL: at CL = 10 pF, use 70 MHz, at CL = 1000 pF, use 700 kHz, and so on. Reducing the pole associated with the load introduces phase shift, thereby reducing phase margin. This results in an error in the increase in phase margin expected by considering the zero alone (equation 1). Equation 3 approximates the reduction in phase margin due to the movement of the pole associated with the load. The result of this equation can be subtracted from the result of the equation 1 to better approximate the improvement in phase margin. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 39 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 APPLICATION INFORMATION driving large capacitive loads (continued) m2 Where : m2 + tan-1 UGBW F x P2 - tan -1 UGBW P2 + reduction in phase margin UGBW + unity-gain bandwidth frequency F + factor from equation (2) P 2 + unadjusted pole (70 MHz @ 10 pF, (3) 7 MHz @ 100 pF, etc.) Using these equations with Figure 60 and Figure 61 enables the designer to choose the appropriate output series resistance to optimize the design of circuits driving large capacitive loads. 50 k VDD + 50 k VI - Rnull + CL VDD - / GND Figure 61. Series-Resistance Circuit 40 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 APPLICATION INFORMATION macromodel information Macromodel information provided was derived using Microsim Parts , the model generation software used with Microsim PSpice . The Boyle macromodel (see Note 5) and subcircuit in Figure 62 are generated using the TLV226x typical electrical and operating characteristics at TA = 25C. Using this information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most cases): D D D D D D D D D D D D Maximum positive output voltage swing Maximum negative output voltage swing Slew rate Quiescent power dissipation Input bias current Open-loop voltage amplification Unity-gain frequency Common-mode rejection ratio Phase margin DC output resistance AC output resistance Short-circuit output current limit NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, "Macromodeling of Intergrated Circuit Operational Amplifiers," IEEE Journal of Solid-State Circuits, SC-9, 353 (1974). 99 3 VCC + 9 RSS 92 FB + 10 J1 DP VC J2 IN + 11 RD1 VAD DC 12 C1 R2 - 53 HLIM - C2 6 - - - + VLN + GCM GA VLIM 8 - RD2 54 4 91 + VLP 7 60 + - + DLP 90 RO2 VB IN - VCC - - + ISS RP 2 1 DLN EGND + - RO1 DE 5 + VE OUT .SUBCKT TLV226x 1 2 3 4 5 C1 11 12 5.5E-12 C2 6 7 20.00E-12 DC 5 53 DX DE 54 5 DX DLP 90 91 DX DLN 92 90 DX DP 4 3 DX EGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5 FB 7 99 POLY (5) VB VC VE VLP + VLN 0 8.84E6 -10E6 10E6 10E6 -10E6 GA 6 0 11 12 62.83E-6 GCM 0 6 10 99 12.34E-9 ISS 3 10 DC 11.05E-6 HLIM 90 0 VLIM 1K J1 11 2 10 JX J2 12 1 10 JX R2 6 9 100.0E3 RD1 60 11 15.92E3 RD2 60 12 15.92E3 R01 8 5 135 R02 7 99 135 RP 3 4 15.87E3 RSS 10 99 18.18E6 VAD 60 4 -.5 VB 9 0 DC 0 VC 3 53 DC .615 VE 54 4 DC .615 VLIM 7 8 DC 0 VLP 91 0 DC 1 VLN 0 92 DC 5.1 .MODEL DX D (IS=800.0E-18) .MODEL JX PJF (IS=500.0E-15 BETA=325E-6 + VTO=-.08) .ENDS Figure 62. Boyle Macromodel and Subcircuit PSpice and Parts are trademarks of MicroSim Corporation. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 41 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PIN SHOWN PINS ** 0.050 (1,27) 8 14 16 A MAX 0.197 (5,00) 0.344 (8,75) 0.394 (10,00) A MIN 0.189 (4,80) 0.337 (8,55) 0.386 (9,80) DIM 0.020 (0,51) 0.014 (0,35) 14 0.010 (0,25) M 8 0.244 (6,20) 0.228 (5,80) 0.008 (0,20) NOM 0.157 (4,00) 0.150 (3,81) 1 Gage Plane 7 A 0.010 (0,25) 0- 8 0.044 (1,12) 0.016 (0,40) Seating Plane 0.069 (1,75) MAX 0.010 (0,25) 0.004 (0,10) 0.004 (0,10) 4040047 / B 03/95 NOTES: A. B. C. D. E. 42 All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Four center pins are connected to die mount pad. Falls within JEDEC MS-012 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.740 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 25 5 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / C 11/95 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 43 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION J (R-GDIP-T**) CERAMIC DUAL-IN-LINE PACKAGE 14 PIN SHOWN PINS ** 14 16 18 20 22 A MAX 0.310 (7,87) 0.310 (7,87) 0.310 (7,87) 0.310 (7,87) 0.410 (10,41) A MIN 0.290 (7,37) 0.290 (7,37) 0.290 (7,37) 0.290 (7,37) 0.390 (9,91) B MAX 0.785 (19,94) 0.785 (19,94) 0.910 (23,10) 0.975 (24,77) 1.100 (28,00) B MIN 0.755 (19,18) 0.755 (19,18) C MAX 0.280 (7,11) 0.300 (7,62) 0.300 (7,62) 0.300 (7,62) C MIN 0.245 (6,22) 0.245 (6,22) 0.245 (6,22) 0.245 (6,22) DIM B 14 8 C 1 7 0.065 (1,65) 0.045 (1,14) 0.100 (2,54) 0.070 (1,78) 0.020 (0,51) MIN 0.930 (23,62) 0.388 (9,65) A 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0- 15 0.100 (2,54) 0.023 (0,58) 0.015 (0,38) 0.014 (0,36) 0.008 (0,20) 4040083 / B 04/95 NOTES: A. B. C. D. E. 44 All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only. Falls within MIL-STD-1835 GDIP1-T14, GDIP1-T16, GDIP1-T18, GDIP1-T20, and GDIP1-T22 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE PACKAGE 0.400 (10,20) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.063 (1,60) 0.015 (0,38) 0-15 0.023 (0,58) 0.015 (0,38) 0.015 (0,38) 0.008 (0,20) 0.100 (2,54) 4040107 / B 04/95 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only Falls within MIL-STD-1835 GDIP1-T8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 45 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION N (R-PDIP-T**) PLASTIC DUAL-IN-LINE PACKAGE 16 PIN SHOWN PINS ** 14 16 18 20 A MAX 0.775 (19,69) 0.775 (19,69) 0.920 (23.37) 0.975 (24,77) A MIN 0.745 (18,92) 0.745 (18,92) 0.850 (21.59) 0.940 (23,88) DIM A 16 9 0.260 (6,60) 0.240 (6,10) 1 8 0.070 (1,78) MAX 0.035 (0,89) MAX 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) M 0- 15 0.010 (0,25) NOM 14/18 PIN ONLY 4040049/C 08/95 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 (20 pin package is shorter then MS-001.) 46 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION P (R-PDIP-T8) PLASTIC DUAL-IN-LINE PACKAGE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0- 15 0.010 (0,25) M 0.010 (0,25) NOM 4040082 / B 03/95 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 47 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PIN SHOWN 0,32 0,19 0,65 14 0,13 M 8 0,15 NOM 4,50 4,30 6,70 6,10 Gage Plane 0,25 1 7 0- 8 0,75 0,50 A Seating Plane 1,20 MAX 0,10 0,10 MIN PINS ** 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064 / D 10/95 NOTES: A. B. C. D. 48 All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION U (S-GDFP-F10) CERAMIC DUAL FLATPACK 0.250 (6,35) 0.246 (6,10) 0.006 (0,15) 0.004 (0,10) 0.080 (2,03) 0.050 (1,27) 0.045 (1,14) 0.026 (0,66) 0.300 (7,62) 0.350 (8,89) 0.250 (6,35) 1 0.350 (8,89) 0.250 (6,35) 10 0.019 (0,48) 0.015 (0,38) 0.050 (1,27) 0.250 (6,35) 5 6 0.025 (0,64) 0.005 (0,13) 1.000 (25,40) 0.750 (19,05) 4040179 / B 03/95 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only. Falls within MIL STD 1835 GDFP1-F10 and JEDEC MO-092AA POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 49 TLV226x, TLV226xA Advanced LinCMOS RAIL-TO-RAIL OPERATIONAL AMPLIFIERS SLOS186A - FEBRUARY 1997 - REVISED JULY 1999 MECHANICAL INFORMATION W (R-GDFP-F16) CERAMIC DUAL FLATPACK Base and Seating Plane 0.285 (7,24) 0.245 (6,22) 0.006 (0,15) 0.004 (0,10) 0.085 (2,16) 0.045 (1,14) 0.045 (1,14) 0.026 (0,66) 0.305 (7,75) 0.275 (6,99) 0.355 (9,02) 0.235 (5,97) 1 0.355 (9,02) 0.235 (5,97) 16 0.019 (0,48) 0.015 (0,38) 0.050 (1,27) 0.440 (11,18) 0.371 (9,42) 0.025 (0,64) 0.015 (0,38) 8 9 1.025 (26,04) 0.745 (18,92) 4040180-3 / B 03/95 NOTES: A. B. C. D. E. 50 All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only. Falls within MIL-STD-1835 GDFP1-F16 and JEDEC MO-092AC POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 1999, Texas Instruments Incorporated