(2.54 mm) .100"
IDMD–24–D–12.00–G
Due to technical progress, all designs, specifications and components are subject to change without notice.
All parts within this catalog are built to Samtec’s specifications.
Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.
WWW.SAMTEC.COM
For complete specifications
see www.samtec.com?IDSS,
www.samtec.com?IDSD,
www.samtec.com?IDMS or
www.samtec.com?IDMD
Insulator Material:
Black Glass Filled Polyester
Plating:
Au over 50 µ" (1.27 µm) Ni or
Sn over 100 µ" (2.54 µm) Cu
or 50 µ" (1.27 µm) Ni
Wire:
28 AWG 7/36 stranded
Tinned Copper
Temperature Range:
-20 °C to +105 °C
(Rainbow Cable)
-40 °C to +105 °C
(Gray Cable)
Voltage Rating:
425 VAC/600 VDC
Contact (IDSS/IDSD):
BeCu
Terminal (IDMS/IDMD):
Phosphor Bronze
Current Rating (IDSD/TST):
3.4 A per pin
(2 pins powered)
Current Rating (IDMD):
3 A per pin
(2 pins powered)
Lead Size Range:
(0.56 mm) .022" SQ to
(0.71 mm) .028" SQ
Lead Insertion Depth:
(5.59 mm) .220" to
(6.22 mm) .245"
RoHS Compliant:
Ye s
END
ASSEMBLY
ROW
OPTION
NO. PINS
PER ROW
TYPE
STRIP
–02 thru –32
–02 thru –36
IDM
= Standard Tail Male Plug
IDS
= Socket
Mates with:
TSW, MTSW, TSM, EJH,
PHT, HMTSW, HTSW,
HW, DW, EW, ZW,
MTLW
IDSD Mates with:
TST, HTST, ZST,
BST, EJH
IDMD
(Double)
S
= Single
D
= Double
(Color coded
cable N/A for
31 thru 36
pins/row.
See –G
option.)
IDMS
(Single)
DOUBLE
Full size (72 positions):
(92.71) 3.650
Less than 72 positions:
No. Positions/row x (2.54) .100 + (1.50) .059
SINGLE
Full size (36 positions):
(91.69) 3.610
Less than 36 positions:
No. Positions/row x (2.54) .100 + (0.48) .019
(2.54)
.100
(0.76)
.030
SQ
(9.27)
.365
REF
(5.08)
.200
(2.54)
.100
IDSD
(Double)
IDSS
(Single)
Socket or Male Plug on one end
Male Plug on one end with socket on
other. Begin part number with IDM.
–T =Transfer
End
Note:
This Series is non-standard,
non-returnable.
(0.48)
.019
DOUBLE
Full size (64 positions):
(82.55) 3.250
Less than 64 positions:
No. Positions/row X (2.54) .100 + (1.68) .066
SINGLE
Full size (32 positions):
(81.53) 3.210
Less than 32 positions:
No. Positions/row X (2.54) .100 + (0.71) .028
(0.46)
.018
x
(0.48)
.019
(2.54)
.100
(2.54)
.100
(2.54)
.100
(5.08)
.200
(6.10)
.240
MAX
(3.18)
.125
(For square or long tail see HCMX Series)
–S =Single
End
–D =Double
End
Socket or Male Plug on each end
SLIM BODY FLAT RIBBON IDC CABLES
OTHER SOLUTIONS
Molded-To-Position
IDC Assemblies
• Low profile
• Skinny side locks
• Dual beam contacts
• Single and double row
• (3.05 mm) .120"
and (5.84 mm) .230"
length tail
available
For complete scope
of recognitions see
www.samtec.com/quality
RECOGNITIONS
SPECIFICATIONS
FILE NO. E111594
F-219 (Rev 11NOV19)
IDSS, IDSD, IDMS, IDMD SERIES
IDSD–24–S–05.00
IDSD–05–D–04.25–S02
Due to technical progress, all designs, specifications and components are subject to change without notice.
All parts within this catalog are built to Samtec’s specifications.
Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.
WWW.SAMTEC.COM
SLIM BODY FLAT RIBBON IDC CABLES
EJECTOR HEADERS
& LOCKING CLIPS
See EJH Series.
LOCKING
CLIP
PC
BOARD
IDSS or IDSD
STRIP ASSEMBLY
.025" SQ
TERMINAL
STRIP (TSW)
See TSW Series.
When mating double row
connector with two single row
connectors, the outer most
single will be connected to
Conductor #1 and the inside
single to Conductor #2.
1/8" (3.18)
1/4" (6.35)
1/2" (12.70)
3/8" (9.53)
–ST8
–ST4
–ST2
–ST3
“XX”
5"max.
2"min.
–O
= Outside Reversed
OPTION
ASSEMBLED
LENGTH
–T
–C
–A
–P “XX”
=Polarized
–R
= Reversed
–D “XX”
= Daisy Chain, Double
–ST “X”
= Stripped & Tinned –S “XX”
= Daisy Chain Single
–G
= Gray Cable
1
2
3
Specify –G for Gray cable. Gray
cable has one red edge. IDSS
and IDMS uses .100" centerline
cable. IDSD and IDMD uses
.050" centerline cable. Cable is
28 AWG 7/36 copper wire.
Standard cable is same as
above except color coded.
Specify “XX” as position. For
Double the same position will
be polarized on both ends.
(Not available on IDM unless
transfer, then only the socket
is polarized.)
Standard plating is selective
gold over BeCu contact for IDS;
Selective gold over phosphor
bronze for IDM.
–W “XX”
= Wiring Reversed
Daisy Chain, Single
Same as –S “XX” except outer
strip connected to Conductor
#2 and inside strip connected
to Conductor #1.
7
7
7
0204
0103
72
71
Assembled Length in
INCHES (±
1
/
8
" )
(2 inches minimum)
Specify Suffix from table.
All dimensions are ± 1/16".
Not available in 28 positions and higher.
4
–B “XX”
= Breakout
Specify “XX” as number of
conductors to be broken out.
Breakout starts with
Number 1 lead indicated
by brown wire or red stripe.
Shown on top side. 5
8
–M
= Middle Reversed
8
8
–RW
= Reversed Wiring
#1 wire opposite position #1.
6
2"
min.
4" minimum
“XX” ± 1⁄8"
Single Row
Connectors
(IDSS)
Outer Most
2"
min.
4" minimum
“XX” ±
1⁄8"
Double Row
Connectors
(IDSD or
IDMD)
Outer Most
Optional polarizing key for
use with IDSS & IDSD
Series. Also polarizes
SSW, SSQ, ESW & ESQ
Series. Black High
Temperature Thermoplastic
Order: Part Number PK-01-06
(Available in wheels of six each)
–R
= Reversed
= Tin Plating
(Both ends)
=
Tin IDM
10 µ" (0.25 µm) Gold IDS
(-T End Assembly Required)
=
10 µ" (0.25 µm) Gold IDM
Tin IDS
(-T End Assembly Required)
– “XX.XX”
= Assembled Length POLARIZING KEY
• Ejector headers
• Locking clips
Requires –SXX, –WXX or –DXX
Requires –SXX, –WXX or –DXX