GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved.
Naos Raptor 6A: Non-Isolated DC-DC Power Modules
4.5Vdc –14Vdc input; 0.59Vdc to 6Vdc output; 6A Output Current
Features
Compliant to RoHS EU Directive 2002/95/EC (Z versions)
Compatible in a Pb-free or SnPb wave-soldering
environment (Z versions)
Wide Input voltage range (4.5Vdc-14Vdc)
Output voltage programmable from 0.59 Vdc to 6Vdc
via external resistor
Tunable LoopTM to optimize dynamic output voltage
response
Fixed switching frequency
Output overcurrent protection (non-latching)
Over temperature protection
Remote On/Off
Cost efficient open frame design
Small size: 10.4 mm x 16.5 mm x 7.84 mm
(0.41 in x 0.65 in x 0.31 in)
Wide operating temperature range (-40°C to 85°C)
UL* 60950-1Recognized, CSA† C22.2 No. 60950-1-03
Certified, and VDE‡ 0805:2001-12 (EN60950-1) Licensed
ISO** 9001 and ISO 14001 certified manufacturing
facilities
Applications
Distributed power architectures
Intermediate bus voltage applications
Telecommunications equipment
Servers and storage applications
Networking equipment
Industrial Applications
Description
The Naos Raptor 6A SIP power modules are non-isolated dc-dc converters in an industry standard package that can
deliver up to 6A of output current with a full load efficiency of 91.5% at 3.3Vdc output voltage (VIN = 12Vdc). These
modules operate over a wide range of input voltage (VIN = 4.5Vdc-14Vdc) and provide a precisely regulated output voltage
from 0.59Vdc to 6Vdc, programmable via an external resistor. Features include remote On/Off, adjustable output voltage,
over current and over temperature protection. A new feature, the Tunable LoopTM, allows the user to optimize the
dynamic response of the converter to match the load.
* UL is a registered trademark of Underwriters Laboratories, Inc.
† CSA is a registered trademark of Canadian Standards Association.
‡ VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
** ISO is a registered trademark of the International Organization of Standards
RoHS Compliant
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 2
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings
only, functional operation of the device is not implied at these or any other conditions in excess of those given in the operations
sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect the device reliability.
Parameter Device Symbol Min Max Unit
Input Voltage All VIN -0.3 15 Vdc
Continuous
Operating Ambient Temperature All TA -40 85 °C
(see Thermal Considerations section)
Storage Temperature All Tstg -55 125 °C
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions.
Parameter Device Symbol Min Typ Max Unit
Operating Input Voltage All VIN 4.5 12 14 Vdc
Maximum Input Current All IIN,max 5.5 Adc
(VIN=4.5V to 14V, IO=IO, max )
Input No Load Current
(VIN = 9Vdc, IO = 0, module ON) VO,set = 0.6 Vdc IIN,No load 30 mA
(VIN = 12Vdc, IO = 0, module ON) VO,set = 5.0Vdc IIN,No load 50 mA
Input Stand-by Current All IIN,stand-by 1 mA
(VIN = 12Vdc, module disabled)
Inrush Transient All I2t 1 A2s
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 1μH source impedance; VIN =0 to
14V, IO= IOmax ; See Test Configurations)
All 35 mAp-p
Input Ripple Rejection (120Hz) All 50 dB
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 3
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Output Voltage Set-point (with 0.5% tolerance for external
resistor used to set output voltage) All VO, set -1.5 +1.5 % VO, set
Output Voltage All VO, set -3.0 +3.0 % VO, set
(Over all operating input voltage, resistive load, and
temperature conditions until end of life)
Adjustment Range All VO 0.59 6 Vdc
Selected by an external resistor
Output Regulation (for Vo ≥ 2.5Vdc)
Line (VIN=VIN, min to VIN, max) All -0.2 +0.2 % VO, set
Load (IO=IO, min to IO, max) All 0.8 % VO, set
Output Regulation (for Vo <2.5Vdc)
Line (VIN=VIN, min to VIN, max) All -5 +5 mV
Load (IO=IO, min to IO, max) All 20 mV
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max Cout = 0.0μF)
Peak-to-Peak (5Hz to 20MHz bandwidth) VO = 0.59Vdc 20 mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth) VO = 1.2Vdc 23 mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth) VO = 1.8Vdc 25 mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth) VO = 2.5Vdc 30 mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth) VO = 3.3Vdc 40 mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth) VO = 5.0Vdc 50 mVpk-pk
Peak-to-Peak (5Hz to 20MHz bandwidth) VO = 6.0Vdc 60 mVpk-pk
External Capacitance1
Without the Tunable LoopTM
ESR ≥ 1 mΩ All CO, max 0 200 μF
With the Tunable LoopTM
ESR ≥ 0.15 mΩ All CO, max 0 1000 μF
ESR ≥ 10 mΩ All CO, max 0 5000 μF
Output Current All Io 0 6 Adc
Output Current Limit Inception (Hiccup Mode ) All IO, lim 150 % Io,max
Output Short-Circuit Current All IO, s/c 9.3 Adc
(VO≤250mV) ( Hiccup Mode )
Efficiency (VIN= 9Vdc) VO,set = 0.59Vdc η 71.8 %
VIN= 12Vdc, TA=25°C VO, set = 1.2Vdc η 81.6 %
IO=IO, max , VO= VO,set VO,set = 1.8Vdc η 86.7 %
VO,set = 2.5Vdc η 89.7 %
VO,set = 3.3Vdc η 91.9 %
VO,set = 5.0Vdc η 94.2 %
VO,set = 6.0Vdc η 95.1 %
Switching Frequency All fsw 600 kHz
1 External capacitors may require using the new Tunable LoopTM feature to ensure that the module is stable as well as getting the best transient
response. See the Tunable LoopTM section for details.
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 4
General Specifications
Parameter Min Typ Max Unit
Calculated MTBF (VIN=12V, VO=5Vdc, IO=0.8IO, max, TA=40°C) Per Telcordia
Method 8,727,077 Hours
Weight 2.9 (0.10) g (oz.)
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature
Descriptions for additional information.
Parameter Device Symbol Min Typ Max Unit
On/Off Signal interface
(VIN=VIN, min to VIN, max; Open collector or equivalent
signal referenced to GND)
Logic High (On/Off pin open - Module ON)
Input High Current All IIH ― 0.5 mA
Input High Voltage All VIH 1.0 ― 12 V
Logic Low (Module Off)
Input Low Current All IIL ― ― 200 µA
Input Low Voltage All VIL -0.3 ― 0.4 V
Turn-On Delay and Rise Times
(IO=IO, max , VIN = VIN, nom, Vo to within ±1% of steady state)
Case 1: On/Off input is enabled and then
input power is applied (delay from instant at which
VIN =VIN, min until Vo=10% of Vo,set)
All
Tdelay
2
3
msec
Case 2: Input power is applied for at least one second
and then On/Off input is set enabled (delay from
instant at which On/Off is enabled until Vo=10% of Vo,
set)
All
Tdelay
2
3
msec
Output voltage Rise time (time for Vo to rise from 10%
of Vo,set to 90% of Vo, set)
All
Trise
3
5
msec
Output voltage overshoot 0.5 % VO, set
IO= IO, max; VIN = VIN, min to VIN, max, TA = 25 oC
Overtemperature Protection All 120 ºC
Input Undervoltage Lockout
Turn-on Threshold All 4.2 Vdc
Turn-off Threshold All 4.1 Vdc
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 5
Characteristic Curves
The following figures provide typical characteristics for the Naos Raptor 6A module at 0.6Vout and at 25ºC.
EFFICIENCY, η (%)
70
72
74
76
78
80
82
012345 6
Vin = 4. 5V
Vin = 6V
Vin = 9V
OUTPUT CURRENT, Io (A)
3
4
5
6
7
25 35 45 55 65 75 85
NC
OUTPUT CURRENT, I
O
(A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 1. Converter Efficiency versus Output Current. Figure 2. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2Adiv) VO (V) (200mV/div)
TIME, t (1µs/div) TIME, t (100µs /div)
Figure 3. Typical output ripple and noise (VIN = 9V, Io = Io,max). Figure 4. Transient Response to Dynamic Load Change
from 0% to 50% to 0% with VIN=9V.
ON/OFF VOLTAGE OUTPUT VOLTAGE
VON/OFF (V) (5V/div) VO (V) (200mV/div)
INPUT VOLTAGE OUTPUT VOLTAGE
VIN (V) (5V/div) VO (V) (200mV/div)
TIME, t (1ms/div) TIME, t (1ms/div)
Figure 5. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 6. Typical Start-up Using Input Voltage (VIN = 9V, Io =
Io,max).
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 6
Characteristic Curves (continued)
The following figures provide typical characteristics for the Naos Raptor 6A module at 1.2Vout and at 25ºC.
EFFICIENCY, η (%)
70
75
80
85
90
95
0123456
Vin = 4. 5V
Vin = 12V
Vin = 14V
OUTPUT CURRENT, Io (A)
3
4
5
6
7
25 35 45 55 65 75 85
NC
OUTPUT CURRENT, I
O
(A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 7. Converter Efficiency versus Output Current. Figure 8. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2Adiv) VO (V) (200mV/div)
TIME, t (1µs/div) TIME, t (100µs /div)
Figure 9. Typical output ripple and noise (VIN = 12V, Io =
Io,max).
Figure 10. Transient Response to Dynamic Load Change
from 0% to 50% to 0% with VIN=12V.
ON/OFF VOLTAGE OUTPUT VOLTAGE
VON/OFF (V) (5V/div) VO (V) (500mV/div)
INPUT VOLTAGE OUTPUT VOLTAGE
VIN (V) (5V/div) VO (V) (500mV/div)
TIME, t (1ms/div)
TIME, t (1ms/div)
Figure 11. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 12. Typical Start-up Using Input Voltage (VIN = 12V,
Io = Io,max).
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 7
Characteristic Curves (continued)
The following figures provide typical characteristics for the Naos Raptor 6A module at 1.8Vout and at 25ºC.
EFFICIENCY, η (%)
70
75
80
85
90
95
0123456
Vin = 4. 5V
Vin = 12V
Vin = 14V
OUTPUT CURRENT, Io (A)
3
4
5
6
7
25 35 45 55 65 75 85
NC
OUTPUT CURRENT, I
O
(A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 73. Converter Efficiency versus Output Current. Figure 14. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2Adiv) VO (V) (200mV/div)
TIME, t (1µs/div) TIME, t (100µs /div)
Figure 15. Typical output ripple and noise (VIN = 12V, Io =
Io,max).
Figure 16. Transient Response to Dynamic Load Change
from 0% to 50% to 0% with VIN=12V.
ON/OFF VOLTAGE OUTPUT VOLTAGE
VON/OFF (V) (5V/div) VO (V) (1V/div)
INPUT VOLTAGE OUTPUT VOLTAGE
VIN (V) (5V/div) VO (V) (1V/div)
TIME, t (1ms/div) TIME, t (1ms/div)
Figure 17. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 18. Typical Start-up Using Input Voltage (VIN = 12V,
Io = Io,max).
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 8
Characteristic Curves (continued)
The following figures provide typical characteristics for the Naos Raptor 6A module at 2.5Vout and at 25ºC.
EFFICIENCY, η (%)
70
75
80
85
90
95
100
0 1 2 3 45 6
Vin = 4. 5V
Vin = 12V
Vin = 14V
OUTPUT CURRENT, Io (A)
3
4
5
6
7
25 35 45 55 65 75 85
NC
0.5m/s
(100LFM)
OUTPUT CURRENT, I
O
(A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 19. Converter Efficiency versus Output Current. Figure 20. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2Adiv) VO (V) (200mV/div)
TIME, t (1µs/div) TIME, t (100µs /div)
Figure 21. Typical output ripple and noise (VIN = 12V, Io =
Io,max).
Figure 22. Transient Response to Dynamic Load Change
from 0% to 50% to 0% with VIN=12V.
ON/OFF VOLTAGE OUTPUT VOLTAGE
VON/OFF (V) (5V/div) VO (V) (1V/div)
INPUT VOLTAGE OUTPUT VOLTAGE
VIN (V) (5V/div) VO (V) (1V/div)
TIME, t (1ms/div) TIME, t (1ms/div)
Figure 23. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 24. Typical Start-up Using Input Voltage (VIN = 12V,
Io = Io,max).
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 9
Characteristic Curves
The following figures provide typical characteristics for the Naos Raptor 6A module at 3.3Vout and at 25ºC.
EFFICIENCY, η (%)
70
75
80
85
90
95
100
0 1 2 3 45 6
Vin = 4. 5V
Vin = 12V
Vin = 14V
OUTPUT CURRENT, Io (A)
3
4
5
6
7
25 35 45 55 65 75 85
NC
0.5m/s
(100LFM)
OUTPUT CURRENT, I
O
(A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 25. Converter Efficiency versus Output Current. Figure 26. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (5Adiv) VO (V) (200mV/div)
TIME, t (1µs/div) TIME, t (100µs /div)
Figure 27. Typical output ripple and noise (VIN = 12V, Io =
Io,max).
Figure 28. Transient Response to Dynamic Load Change
from 0% to 50% to 0% with VIN=12V.
ON/OFF VOLTAGE OUTPUT VOLTAGE
VON/OFF (V) (5V/div) VO (V) (1V/div)
INPUT VOLTAGE OUTPUT VOLTAGE
VIN (V) (5V/div) VO (V) (1V/div)
TIME, t (1ms/div) TIME, t (1ms/div)
Figure 29. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 30. Typical Start-up Using Input Voltage (VIN = 12V,
Io = Io,max).
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 10
Characteristic Curves (continued)
The following figures provide typical characteristics for the Naos Raptor 6A module at 5Vout and at 25ºC.
EFFICIENCY, η (%)
70
75
80
85
90
95
100
012 3 45 6
Vin = 6V
Vin = 12V
Vin = 14V
OUTPUT CURRENT, Io (A)
3
4
5
6
7
25 35 45 55 65 75 85
NC
0.5m/s
(100LFM)
OUTPUT CURRENT, I
O
(A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 31. Converter Efficiency versus Output Current. Figure 32. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2Adiv) VO (V) (200mV/div)
TIME, t (1µs/div) TIME, t (100µs /div)
Figure 33. Typical output ripple and noise (VIN = 12V, Io =
Io,max).
Figure 34. Transient Response to Dynamic Load Change
from 0% to 50% to 0% with VIN=12V.
ON/OFF VOLTAGE OUTPUT VOLTAGE
VON/OFF (V) (5V/div) VO (V) (2V/div)
INPUT VOLTAGE OUTPUT VOLTAGE
VIN (V) (5V/div) VO (V) (2V/div)
TIME, t (1ms/div) TIME, t (1ms/div)
Figure 35. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 36. Typical Start-up Using Input Voltage (VIN = 12V,
Io = Io,max).
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 11
Characteristic Curves
The following figures provide typical characteristics for the Naos Raptor 6A module at 6Vout and at 25ºC.
EFFICIENCY, η (%)
70
75
80
85
90
95
100
01234 5 6
Vin = 7V
Vin = 12V
Vin = 14V
OUTPUT CURRENT, Io (A)
3
4
5
6
7
25 35 45 55 65 75 85
NC
0.5m/s
(100LFM)
OUTPUT CURRENT, I
O
(A)
AMBIENT TEMPERATURE, T
A
O
C
Figure 37. Converter Efficiency versus Output Current. Figure 38. Derating Output Current versus Ambient
Temperature and Airflow.
OUTPUT VOLTAGE
VO (V) (10mV/div)
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2Adiv) VO (V) (200mV/div)
TIME, t (1µs/div) TIME, t (100µs /div)
Figure 39. Typical output ripple and noise (VIN = 12V, Io =
Io,max).
Figure 40. Transient Response to Dynamic Load Change
from 0% to 50% to 0% with VIN=12V.
ON/OFF VOLTAGE OUTPUT VOLTAGE
VON/OFF (V) (5V/div) VO (V) (2V/div)
INPUT VOLTAGE OUTPUT VOLTAGE
VIN (V) (5V/div) VO (V) (2V/div)
TIME, t (1ms/div) TIME, t (1ms/div)
Figure 41. Typical Start-up Using On/Off Voltage (Io = Io,max). Figure 42. Typical Start-up Using Input Voltage (VIN = 12V,
Io = Io,max).
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 12
Test Configurations
TO OSCILLOSCOPE
CURRENT PROBE
L
TEST
1μH
BATTERY
C
S
1000μF
Electrolytic
E.S.R.<0.1Ω
@ 20°C 100kHz
2x100μF
Tantalum
V
IN
(+)
COM
NOTE: Measure input ref l ect ed ripple current with a sim ulated
source inductance (LTEST) of 1μH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
C
IN
Figure 43. Input Reflected Ripple Current Test Setup.
NOTE: All voltage measurem ents to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
V
O
(+)
COM
1uF
.
RESISTIVE
LOAD
SCOPE
COPPER STRIP
GROUND PLANE
10uF
Figure 44. Output Ripple and Noise Test Setup.
V
O
COM
V
IN
(+)
COM
R
LOAD
R
contact
R
distribution
R
contact
R
distribution
R
contact
R
contact
R
distribution
R
distribution
V
IN
V
O
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvi n c onnec ti ons are r equ ired at the m odu l e t ermi n als
to avoi d m eas urem en t errors du e t o s oc k et c ontact
resistance.
Figure 45. Output Voltage and Efficiency Test Setup.
η
=
V
O
.
I
O
V
IN
.
I
IN
x
100
%
Efficiency
Design Considerations
Input Filtering
The Naos Raptor 6A module should be connected to a low-
impedance source. A highly inductive source can affect the
stability of the module. An input capacitance must be placed
directly adjacent to the input pin of the module, to minimize
input ripple voltage and ensure module stability.
To minimize input voltage ripple, low-ESR ceramic or polymer
capacitors are recommended at the input of the module. Figure 46
shows the input ripple voltage for various output voltages at 6A of
load current with 1x22 µF or 2x22 µF ceramic capacitors and an
input of 12V.
Input Ripple Voltage (mVp-p)
0
20
40
60
80
100
120
140
160
0.5 11.5 22.5 33.5 44.5 5
1x22uF
2x22uF
Output Voltage (Vdc)
Figure 46. Input ripple voltage for various output voltages with
1x22 µF or 2x22 µF ceramic capacitors at the input (6A load).
Input voltage is 12V.
Output Filtering
The Naos Raptor 6A modules are designed for low output ripple
voltage and will meet the maximum output ripple specification
with no external capacitors. However, additional output filtering
may be required by the system designer for a number of reasons.
First, there may be a need to further reduce the output ripple and
noise of the module. Second, the dynamic response
characteristics may need to be customized to a particular load
step change.
To reduce the output ripple and improve the dynamic response to
a step load change, additional capacitance at the output can be
used. Low ESR ceramic and polymer are recommended to improve
the dynamic response of the module. Figure 47 provides output
ripple information for different external capacitance values at
various Vo and for a load current of 6A. For stable operation of the
module, limit the capacitance to less than the maximum output
capacitance as specified in the electrical specification table.
Optimal performance of the module can be achieved by using the
Tunable LoopTM feature described later in this data sheet.
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 13
0
10
20
30
40
0.5 11.5 22.5 33.5 44.5 5
Output Voltage(V ol ts)
Ripple(mVp-p)
1x 10uF E xternal Cap
1x 47uF E xternal Cap
2x 47uF E xternal Cap
4x 47uF E xternal Cap
Figure 47. Output ripple voltage for various output voltages
with external 1x10 µF, 1x47 µF, 2x47 µF or 4x47 µF ceramic
capacitors at the output (6A load). Input voltage is 12V.
Safety Considerations
For safety agency approval the power module must be installed in
compliance with the spacing and separation requirements of the
end-use safety agency standards, i.e., UL 60950-1, CSA C22.2 No.
60950-1-03, and VDE 0850:2001-12 (EN60950-1) Licensed.
For the converter output to be considered meeting the
requirements of safety extra-low voltage (SELV), the input must
meet SELV requirements. The power module has extra-low voltage
(ELV) outputs when all inputs are ELV.
An input fuse for the module is recommended. Due to the wide
input voltage and output voltage ranges of the module, different
fuse ratings are recommended as shown in Table 1. These are
suggested “maximum” fuse ratings. However, for optimum circuit
protection, the fuse value should not be any larger than required in
the end application. As an option to using a fuse, no fuse is
required, if the module is
1. powered by a power source with current limit protection
set point less than the protection device value listed in
Table 1, and
2. the module is evaluated in the end-use equipment.
Table 1.
Input
Voltage
(VDC)
Output Voltage (VDC)
0.59 to 1.3 1.31 to 2.7 2.71 to 5.0 5.1 to 6
10.1 to 14
3A
6A
10A
12A
6.51 to 10
4A
8A
15A
12A
4.5 to 6.5
6A
12A
15A
NA
Feature Descriptions
Remote On/Off
The Naos Raptor 6A modules feature an On/Off pin with positive
logic for remote On/Off operation. If the On/Off pin is not being
used, leave the pin open (the module will be ON, except for the -49
option modules where leaving the pin open will cause the module
to remain OFF). The On/Off signal (VOn/Off) is referenced to ground.
During a Logic High on the On/Off pin, the module remains ON.
During Logic-Low, the module is turned OFF.
ON/OFF
VIN
GND
MODULE
ENABLE
R1
100K
2.2K
47K
2.2K
47K
10K 30.1K
Figure 48. Remote On/Off Implementation. Resistor R1 is absent
in the -49Z option module.
Overcurrent Protection
To provide protection in a fault (output overload) condition, the unit
is equipped with internal current-limiting circuitry and can endure
current limiting continuously. At the point of current-limit inception,
the unit enters hiccup mode. The unit operates normally once the
output current is brought back into its specified range. The average
output current during hiccup is 10% IO, max.
Overtemperature Protection
To provide protection in a fault condition, these modules are
equipped with a thermal shutdown circuit. The unit will shut down
if the overtemperature threshold of 130ºC is exceeded at the
thermal reference point Tref. The thermal shutdown is not intended
as a guarantee that the unit will survive temperatures beyond its
rating. Once the unit goes into thermal shutdown it will then wait
to cool before attempting to restart.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout limit, the
module operation is disabled. The module will begin to operate at
an input voltage above the undervoltage lockout turn-on
threshold.
Feature Descriptions (continued)
Output Voltage Programming
The output voltage of the Naos Raptor 6A module can be
programmed to any voltage from 0.59dc to 6Vdc by connecting a
resistor between the Trim+ and GND pins of the module. Certain
restrictions apply on the output voltage set point depending on the
input voltage. These are shown in the Output Voltage vs. Input
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 14
Voltage Set Point Area plot in Fig. 49. The Upper Limit curve shows
that for output voltages of 0.9V and lower, the input voltage must
be lower than the maximum of 14V. The Lower Limit curve shows
that for output voltages of 3.8V and higher, the input voltage needs
to be larger than the minimum of 4.5V.
0
2
4
6
8
10
12
14
16
0.5 11.5 22.5 33.5 44.5 55.5 6
O ut put Voltage ( V)
I nput Vol tage ( v)
Lower Lim it
Upper Lim it
Figure 49. Output Voltage vs. Input Voltage Set Point Area plot
showing limits where the output voltage can be set for different
input voltages.
Without an external resistor between Trim+ and GND pins, the
output of the module will be 0.59Vdc. To calculate the value of the
trim resistor, Rtrim for a desired output voltage, use the following
equation:
( )
Ω
−
=k
Vo
Rtrim 591.0
182.1
Rtrim is the external resistor in kΩ
Vo is the desired output voltage
Table 2 provides Rtrim values required for some common output
voltages.
Table 2
V
O, set
(V)
Rtrim (KΩ)
0.59
Open
1.0
2.89
1.2
1.941
1.5
1.3
1.8
0.978
2.5
0.619
3.3
0.436
5.0
0.268
6.0
0.219
By using a ±0.5% tolerance trim resistor with a TC of ±25ppm, a set
point tolerance of ±1.5% can be achieved as specified in the
electrical specification. The POL Programming Tool available at
www.lineagepower.com under the Design Tools section, helps
determine the required trim resistor needed for a specific output
voltage.
V
O
(+)
TRIM
GND
R
trim
LOAD
V
IN
(+)
ON/OFF
Vout
Figure 50. Circuit configuration for programming output
voltage using an external resistor.
Voltage Margining
Output voltage margining can be implemented in the Naos Raptor
6A modules by connecting a resistor, Rmargin-up, from the Trim pin to
the ground pin for margining-up the output voltage and by
connecting a resistor, Rmargin-down, from the Trim pin to output pin
for margining-down. Figure 51 shows the circuit configuration for
output voltage margining. The POL Programming Tool, available at
www.lineagepower.com under the Design Tools section, also
calculates the values of Rmargin-up and Rmargin-down for a specific
output voltage and % margin. Please consult your local Lineage
Power technical representative for additional details.
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 15
Feature Descriptions (continued)
Vo
MODULE
GND
Trim
Q1
Rtrim
Rmargin-up
Q2
Rmargin-down
Figure 51. Circuit Configuration for margining Output voltage.
Monotonic Start-up and Shutdown
The Naos Raptor 6A modules have monotonic start-up and
shutdown behavior for any combination of rated input voltage,
output current and operating temperature range.
Tunable LoopTM
The Naos Raptor 6A modules have a new feature that optimizes
transient response of the module called Tunable LoopTM. External
capacitors are usually added to improve output voltage transient
response due to load current changes. Sensitive loads may also
require additional output capacitance to reduce output ripple and
noise. Adding external capacitance however affects the voltage
control loop of the module, typically causing the loop to slow down
with sluggish response. Larger values of external capacitance
could also cause the module to become unstable.
To use the additional external capacitors in an optimal manner, the
Tunable LoopTM feature allows the loop to be tuned externally by
connecting a series R-C between the VOUT and TRIM pins of the
module, as shown in Fig. 52. This R-C allows the user to externally
adjust the voltage loop feedback compensation of the module to
match the filter network connected to the output of the module.
Recommended values of RTUNE and CTUNE are given in Tables 3 and
4. Table 3 lists recommended values of RTUNE and CTUNE in order to
meet 2% output voltage deviation limits for some common output
voltages in the presence of a 3A to 6A step change (50% of full
load), with an input voltage of 12V. Table 4 shows the
recommended values of RTUNE and CTUNE for different values of
ceramic output capacitors up to 1000uF, again for an input voltage
of 12V. The value of RTUNE should never be lower than the values
shown in Tables 3 and 4. Please contact your Lineage Power
technical representative to obtain more details of this feature as
well as for guidelines on how to select the right value of external R-
C to tune the module for best transient performance and stable
operation for other output capacitance values.
MODULE
TRIM
VOUT
GND
RTUNE
CTUNE
RTrim
Figure. 52. Circuit diagram showing connection of RTUME and
CTUNE to tune the control loop of the module.
Table 3. Recommended values of RTUNE and CTUNE to obtain
transient deviation of 2% of Vout for a 3A step load with
Vin=12V.
Vout 5V 3.3V 2.5V 1.8V 1.2V 0.69V
Cext 2x47µF
3x47µF
4x47µF 330µF
Polymer
2x47µF +
330µF
Polymer
4x330µF
Polymer
R
TUNE 100 75 47 47 47 47
C
TUNE 12nF 27nF 39nF 100nF 220nF 330nF
∆V
81mV 57mV 43mV 27mV 24mV 11mV
Table 4. General recommended values of of RTUNE and CTUNE for
Vin=12V and various external ceramic capacitor combinations.
Cext 1x47
µ
F 2x47
µ
F 4x47
µ
F 10x47
µ
F 20x47
µ
F
RTUNE 150 100 47 47 47
CTUNE 10nF 12nF 39nF 68nF 82nF
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 16
Thermal Considerations
Power modules operate in a variety of thermal environments;
however, sufficient cooling should be provided to help ensure
reliable operation.
Considerations include ambient temperature, airflow, module
power dissipation, and the need for increased reliability. A
reduction in the operating temperature of the module will result in
an increase in reliability. The thermal data presented here is based
on physical measurements taken in a wind tunnel. . The test set-
up is shown in Figure 53. The preferred airflow direction for the
module is in Figure 54.
Figure 53. Thermal Test Set-up.
The thermal reference point, Tref used in the specifications of
thermal derating curves is shown in Figure 54. For reliable
operation this temperature should not exceed 120ºC.
The output power of the module should not exceed the rated
power of the module (Vo,set x Io,max).
Please refer to the Application Note “Thermal Characterization
Process For Open-Frame Board-Mounted Power Modules” for a
detailed discussion of thermal aspects including maximum device
temperatures
Figure 54. Tref Temperature measurement location.
Post solder Cleaning and Drying Considerations
Post solder cleaning is usually the final circuit-board assembly
process prior to electrical board testing. The result of inadequate
cleaning and drying can affect both the reliability of a power
module and the testability of the finished circuit-board assembly.
For guidance on appropriate soldering, cleaning and drying
procedures, refer to Board Mounted Power Modules: Soldering and
Cleaning Application Note.
Through-Hole Lead-Free Soldering Information
The RoHS-compliant through-hole products use the SAC (Sn/Ag/Cu)
Pb-free solder and RoHS-compliant components. They are
designed to be processed through single or dual wave soldering
machines. The pins have an RoHS-compliant finish that is
compatible with both Pb and Pb-free wave soldering processes. A
maximum preheat rate of 3°C/s is suggested. The wave preheat
process should be such that the temperature of the power module
board is kept below 210°C. For Pb solder, the recommended pot
temperature is 260°C, while the Pb-free solder pot is 270°C max.
Not all RoHS-compliant through-hole products can be processed
with paste-through-hole Pb or Pb-free reflow process. If additional
information is needed, please consult with your Lineage Power
technical representative for more details.
Airflow Direction
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 17
Mechanical Outline
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
Pin out
Pin
Function
1
On/Off
2
V
IN
3
GND
4
V
out
5
Trim+
H = 4.8 [0.19]
L = 3.29 [0.13]
Front View
Side View
GE
Data Sheet
February 11, 2016 ©2016 General Electric Company. All rights reserved. Page 18
Recommended Pad Layout
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm (x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm (x.xxx in ± 0.010 in.)
GE
Data Sheet
Contact Us
For more information, call us at
USA/Canada:
+1 877 546 3243, or +1 972 244 9288
Asia-Pacific:
+86.021.54279977*808
Europe, Middle-East and Africa:
+49.89.878067-280
www.gecriticalpower.com
GE Critical Power reserves the right to make changes to the product(s) or information contained herein without notice, and no
liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s)
or information.
February 11, 2016 ©2016 General Electric Company. All International rights reserved. Version 1.14
Ordering Information
Please contact your Lineage Power Sales Representative for pricing, availability and optional features.
Table 5. Device Codes
Device Code
Input
Voltage Range
Output
Voltage
Output
Current
On/Off
Logic
Connector
Type
Comcodes
NSR006A0X4Z 4.5 – 14Vdc 0.59 – 6Vdc 6A Positive SIP CC109130894
NSR006A0X4-49Z* 4.5 – 14Vdc 0.59 – 6Vdc 6A Positive SIP CC109138194
Z refers to RoHS-compliant product.
* Special codes, consult factory before ordering
Table 6. Device Options
Series
generation
Output
Current
Output
voltage
Pin Length
On / Off
logic
Sense
Default On/Off
Condition
Options
ROHS Compliance
NSR
006A0
X
4
Z
006A0 =
6A
X =
program
mable
output
Blank =
Standard
5=5.1mm
6=3.7mm
8=2.8mm
4 = positive
No entry =
negative
3 = Remote
Sense
Blank =
without
Blank =
Standard, ON
when
unconnected
2=Inverted
On/Off
-Y = without
outrigger pins
Z = ROHS6