4/98
GBL005 THRU GBL10
GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER
Reverse Voltage - 50 to 1000 Volts Forward Current - 4.0 Amperes
FEATURES
♦ Plastic package has Underwriters Laboratory Flammability
Classification 94V-0
♦ This series is UL listed under the Recognized Component
Index, file number E54214
♦ Glass passivated chip junctions
♦ High case dielectric strength
♦ Typical IRless than 0.1µA
♦ High surge current capability
♦ Ideal for pr inted circuit boards
♦ High temperature soldering guaranteed:
260°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
MECHANICAL DATA
Case: Molded plastic body over passivated junctions
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Mounting Position: Any
Weight: 0.071 ounce, 2.0 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
GBL GBL GBL GBL GBL GBL GBL
SYMBOLS 005 01 02 04 06 08 10 UNITS
Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 1000 Volts
Maximum RMS voltage VRMS 35 70 140 280 420 560 700 Volts
Maximum DC blocking voltage VDC 50 100 200 400 600 800 1000 Volts
Maximum average forward TC=50°C (NOTE 1) 4.0
rectified output current at TA=40°C (NOTE 2) I(AV) 3.0 Amps
Peak forward surge current, single half sine-wave
superimposed on rated load (JEDEC Method) TJ=150°C IFSM 150.0 Amps
Rating for fusing (t<8.3ms) I2t 93.0 A2sec
Maximum instantaneous forward drop per leg
at 4.0 Amperes VF1.1 Volts
Maximum DC reverse current at rated TA=25°C 5.0
DC blocking voltage per leg TA=125°C IR500.0 µA
Typical junction capacitance per leg (NOTE 3) CJ95.0 40.0 pF
Typical thermal resistance per leg (NOTE 1) RΘJA 22.0
(NOTE 2) RΘJL 3.5 °C/W
Operating junction storage and temperature range TJ, TSTG -55 to +150 °C
NOTES:
(1) Unit mounted on 3.0 x 3.0 x 0.11" thick (7.5 x 7.5 x 0.3cm) Al. plate
(2) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length and 0.5 x 0.5" (12 x12mm) copper pads
(3) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
Case Type GBL
0.125 (3.17)
x 45 degrees
Chamfer
0.080 (2.03)
0.060 (1.50)
0.095 (2.41)
0.080 (2.03)
0.825 (20.9)
0.815 (20.7)
0.050 (1.27)
0.040 (1.02)
Polarity shown on front side of case: positive lead by beveled corner
0.040 (1.02)
0.030 (0.76)
0.022 (0.56)
0.018 (0.46)
0.210
0.190(5.3)
(4.8)
0.421 (10.7)
0.411 (10.4)
0.718 (18.2)
0.682 (17.3)
0.140 (3.56)
0.128 (3.25)
Lead Depth
0.098 (2.5)
0.075 (1.9)
0.098 (2.5)
0.075 (1.9)
0.022 (0.56)
0.018 (0.46)
Dimensions in inches and (millimeters)
050 100 150
0
1.0
2.0
3.0
4.0
5.0
110 100
0
50
100
150
0.4 0.6 0.8 1.0 1.2 1.4 1.6
0.01
0.1
1
10
100
0.1 110 100
10
100
1,000
020 40 60 80 100
0.01
0.1
1
10
100
500
0.01 0.1 110 100
0.1
1
10
100
RATINGS AND CHARACTERISTICS CURVES GBL005 THRU GBL10
FIG. 1 - DERATING CURVES OUTPUT RECTIFIED
CURRENT
AMBIENT TEMPERATURE, °C
P.C.B. MOUNTING
0.47 x 0.47” (12 x 12mm)
COPPER PADS
0.375” (9.5mm) LEAD LENGTH
60Hz RESISTIVE OR INDUCTIVE LOAD
60 Hz RESISTIVE OR INDUCTIVE LOAD
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
FIG. 3 - TYPICAL FORWARD VOLTAGE
CHARACTERISTICS PER LEG
INSTANTANEOUS FORWARD CURRENT, AMPERES
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
PER LEG
REVERSE VOLTAGE, VOLTS
TJ=25°C
f=1.0 MHz
Vsig=50mVp-p
TA=25°C
HEAT-SINK
MOUNTING,
3.0 x 3.0 x 0.11” THK
(7.5 x 7.5 x 0.3cm)
AL. PLATE
AVERAGE FORWARD OUTPUT CURRENT,
AMPERES
FIG. 4 - TYPICAL REVERSE LEAKAGE
CHARACTERISTICS PER LEG
NUMBER OF CYCLES AT 60 Hz
PEAK FORWARD SURGE CURRENT,
AMPERES
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT PER LEG
TA=125°C
FIG. 6 - TYPICAL TRANSIENT THERMAL
IMPEDANCE PER LEG
TRANSIENT THERMAL IMPEDANCE,
°C/W
t, HEATING TIME, sec.
50 - 400V
600 - 1000V
50 - 400V
600 - 1000V
TJ = TJ max.
SINGLE SINE-WAVE
(JEDEC Method)
JUNCTION CAPACITANCE, pF
1.0 CYCLE
