[AK4425A] AK4425A 192kHz 24-Bit Stereo DAC with 2Vrms Output GENERAL DESCRIPTION The AK4425A is a 5V 24-bit stereo DAC with an integrated 2Vrms output buffer. A charge pump in the buffer develops an internal negative power supply rail that enables a ground-referenced 2Vrms output. Using AKM's multi bit modulator architecture, the AK4425A delivers a wide dynamic range while preserving linearity for improved THD+N performance. The AK4425A integrates a combination of switched-capacitor and continuous-time filters, increasing performance for systems with excessive clock jitter. The 24-bit word length and 192kHz sampling rate make this part ideal for a wide range of consumer audio applications, such as DVD, AV receiver system and set-top boxes. The AK4425A is offered in a space saving 16pin TSSOP package. FEATURES Sampling Rate Ranging from 8kHz to 192kHz 128 times Oversampling (Normal Speed Mode) 64 times Oversampling (Double Speed Mode) 32 times Oversampling (Quad Speed Mode) 24-Bit 8 times FIR Digital Filter Switched-Capacitor Filter with High Tolerance to Clock Jitter Single Ended 2Vrms Output Buffer Digital De-emphasis Filter: 32kHz, 44.1kHz or 48kHz Soft mute Digital Attenuator (Linear 256 Step) Control I/F: 3-wire Audio I/F format: 24Bit MSB justified, 24/20/16 LSB justified or I2S compatible Master clock: 256fs, 384fs, 512fs, 768fs or 1152fs (Normal Speed Mode) 128fs, 192fs, 256fs or 384fs (Double Speed Mode) 128fs, 192fs (Quad Speed Mode) THD+N: -91dB Dynamic Range: 106dB Automatic Power-on Reset Circuit Power supply: +4.5 +5.5V Ta = -20 to 85C Small Package: 16pin TSSOP (6.4mm x 5.0mm) MS1127-E-01 2011/03 -1- [AK4425A] MCLK AVDD CSN CCLK CDTI Control Interface Clock Divider De-emphasis Control VSS2 LRCK BICK SDTI Audio Data Interface 8X Interpolator Modulator SCF LPF AOUTL 8X Interpolator Modulator SCF LPF AOUTR Charge Pump CP CN 1 VEE VSS1 VDD 1 Block Diagram MS1127-E-01 2011/03 -2- [AK4425A] Ordering Guide AK4425AET AKD4425A -20 +85C 16pin TSSOP (0.65mm pitch) Evaluation Board for AK4425A Pin Layout VDD 1 16 VSS1 MCLK 2 15 CP BICK 3 14 CN SDTI 4 13 VEE LRCK 5 12 AOUTL CSN 6 11 VSS2 CCLK 7 10 AVDD CDTI 8 9 AOUTR AK4425A Top View Compatibility with the AK4426 Functions Power Supply DC Offset THD+N DR DEM SMUTE Digital ATT I/F Format Control I/F Operating Temperature AK4426 +4.5 +5.5V 8mV -91dB 106dB X X X 24-bit MSB/ IS/ 24,20,16bitLSB IC ET: -20 +85C VT: -40 +85C AK4425A A 5mV A A A A A A A A -: Not available X: Available MS1127-E-01 2011/03 -3- [AK4425A] PIN/FUNCTION No. 1 Pin Name VDD I/O - Function Digital Circuit and Charge Pump Circuit Power Supply Pin: 4.5V5.5V Master Clock Input Pin 2 MCLK I An external TTL clock must be input on this pin. 3 Audio Serial Data Clock Pin BICK I 4 Audio Serial Data Input Pin SDTI I 5 L/R Clock Pin LRCK I 6 Chip Select Pin CSN I 7 Control Clock input Pin CCLK I 8 Control Data Input Pin CDTI I Rch Analog Output Pin 9 AOUTR O When power down, outputs VSS(0V, typ). 10 Analog Block Power Supply Pin: 4.5V5.5V AVDD 11 Ground Pin2 VSS2 Lch Analog Output Pin 12 AOUTL O When power down, outputs VSS(0V, typ). Negative Voltage Output Pin Connect to VSS1 with a 1.0F capacitor which is low ESR (Equivalent 13 Series Resistance) over all temperature range. When this capacitor has the VEE O polarity, the positive polarity pin must be connected to the VSS1 pin. Non polarity capacitors can also be used. Negative Charge Pump Capacitor Terminal Pin Connect to CP with a 1.0F capacitor which is low ESR (Equivalent Series 14 Resistance) over all temperature range. When this capacitor has the polarity, CN I the positive polarity pin must be connected to the CP pin. Non polarity capacitors can also be used. Positive Charge Pump Capacitor Terminal Pin Connect to CN with a 1.0F capacitor which is low ESR (Equivalent Series 15 Resistance) over all temperature range. When this capacitor has the polarity, CP I the positive polarity pin must be connected to the CP pin. Non polarity capacitors can also be used. 16 Ground Pin1 VSS1 Note: All input pins except for the CN pin should not be left floating. MS1127-E-01 2011/03 -4- [AK4425A] ABSOLUTE MAXIMUM RATINGS (VSS1=VSS2=0V; Note 1) Parameter Power Supply Symbol VDD CVDD IIN VIND Ta Tstg Input Current (any pins except for supplies) Input Voltage Ambient Operating Temperature Storage Temperature Note 1. All voltages with respect to ground. Note 2. VSS1, VSS2 connect to the same analog ground. min -0.3 -0.3 -0.3 -20 -65 max +6.0 +6.0 10 VDD+0.3 85 150 Units V V mA V C C WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is not guaranteed at these extremes. RECOMMENDED OPERATING CONDITIONS (VSS1=VSS2=0V; Note 1) Parameter Power Supply Symbol VDD AVDD min +4.5 typ +5.0 VDD max +5.5 Units V Note 3. AVDD should be equal to VDD *AKM assumes no responsibility for the usage beyond the conditions in this datasheet. MS1127-E-01 2011/03 -5- [AK4425A] ANALOG CHARACTERISTICS (Ta = 25C; VDD=AVDD = +5.0V; fs = 44.1 kHz; BICK = 64fs; Signal Frequency = 1 kHz; 24bit Input Data; Measurement frequency = 20Hz 20kHz; RL 5k) Parameter min typ max Units Resolution 24 Bits Dynamic Characteristics (Note 4) THD+N fs=44.1kHz, BW=20kHz -91 -84 dB fs=96kHz, BW=40kHz -91 dB fs=192kHz, BW=40kHz -91 dB Dynamic Range (-60dBFS with A-weighted. (Note 5) 100 106 dB S/N (A-weighted. (Note 6) 100 106 dB Interchannel Isolation (1kHz) 90 100 dB Interchannel Gain Mismatch 0 0.5 dB DC Accuracy DC Offset (at output pin) -5 0 +5 mV Gain Drift 100 ppm/C Output Voltage (Note 7) 2.05 2.2 2.35 Vrms Load Capacitance (Note 8) 25 pF Load Resistance 5 k Power Supplies Power Supply Current: (Note 9) 24 36 mA Normal Operation (fs96kHz) 27 40 mA Normal Operation (fs=192kHz) 10 100 Power-Down Mode (Note 10) A Note 4. Measured by Audio Precision (System Two). Refer to the evaluation board manual. Note 5. 98dB for 16bit input data Note 6. S/N does not depend on input data size. Note 7. Full-scale voltage (0dB). Output voltage is proportional to the voltage of VDD, AOUT (typ.@0dB) = 2.2Vrms x VDD/5. Note 8. In case of driving capacitive load, inset a resistor between the output pin and the capacitive load. Note 9. The current into VDD and AVDD. Note 10. All digital inputs including clock pins (MCLK, BICK and LRCK) are fixed to VSS1(VSS2) or VDD(AVDD). MS1127-E-01 2011/03 -6- [AK4425A] SHARP ROLL-OFF FILTER CHARACTERISTICS (Ta = 25C; VDD=AVDD = +4.5 +5.5V; fs = 44.1 kHz; DEM = OFF; SLOW = "0") Parameter Symbol min typ max Digital filter PB 0 20.0 Passband 0.05dB (Note 11) 22.05 -6.0dB Stopband (Note 11) SB 24.1 Passband Ripple PR 0.02 Stopband Attenuation SA 54 Group Delay (Note 12) GD 19.3 Digital Filter + LPF Frequency Response 20.0kHz fs=44.1kHz FR 0.05 40.0kHz fs=96kHz FR 0.05 80.0kHz fs=192kHz FR 0.05 Note 11. The passband and stopband frequencies scale with fs(system sampling rate). For example, PB=0.4535xfs (@0.05dB), SB=0.546xfs. Note 12. Calculated delay time caused by digital filter. This time is measured from setting the 16/24bit data of both channels to input register to the output of the analog signal. Units kHz kHz kHz dB dB 1/fs dB dB dB SLOW ROLL-OFF FILTER CHARACTERISTICS (Ta = 25C; VDD=AVDD = +4.5 +5.5V; fs = 44.1kHz; DEM = OFF; SLOW = "1") Parameter Symbol min PB 0 39.2 typ max Units 18.2 8.1 - Digital Filter 0.04dB (Note 13) -3.0dB Stopband (Note 13) Passband Ripple Stopband Attenuation Group Delay (Note 12) Passband 19.3 - kHz kHz kHz dB dB 1/fs FR +0/-5 20.0kHz fs=44.kHz 40.0kHz fs=96kHz FR +0/-4 fs=192kHz 80.0kHz FR +0/-5 Note 13. The passband and stopband frequencies scale with fs(system sampling rate). For example, PB=0.185xfs (@0.04dB), SB=0.888xfs. - dB dB dB SB PR SA GD 0.005 72 - Digital Filter + LPF Frequency Response MS1127-E-01 2011/03 -7- [AK4425A] DC CHARACTERISTICS (Ta = 25C; VDD=AVDD = +4.5 +5.5V) Parameter High-Level Input Voltage Low-Level Input Voltage Input Leakage Current Symbol VIH VIL Iin min 2.2 - SWITCHING CHARACTERISTICS (Ta = 25C; VDD=AVDD = +4.5 +5.5V) Parameter Symbol min Typ fCLK 2.048 11.2896 Master Clock Frequency dCLK 30 Duty Cycle LRCK Frequency Normal Speed Mode fsn 8 Double Speed Mode fsd 32 Quad Speed Mode fsq 120 Duty Cycle Duty 45 Audio Interface Timing BICK Period tBCK 1/128fsn Normal Speed Mode tBCK 1/64fsd Double Speed Mode tBCK 1/64fsq Quad Speed Mode tBCKL 30 BICK Pulse Width Low tBCKH 30 Pulse Width High tBLR 20 BICK "" to LRCK Edge (Note 14) tLRB 20 LRCK Edge to BICK "" (Note 14) tSDH 20 SDTI Hold Time tSDS 20 SDTI Setup Time Control Interface Timing tCCK 200 CCLK Period tCCKL 80 CCLK Pulse Width Low tCCKH 80 Pulse Width High tCDS 40 CDTI Setup Time tCDH 40 CDTI Hold Time tCSW 150 CSN High Time tCSS 50 CSN "" to CCLK "" tCSH 50 CCLK "" to CSN "" Note 14. BICK rising edge must not occur at the same time as LRCK edge. MS1127-E-01 typ - max 0.8 10 Units V V A max 36.864 70 Units MHz % 48 96 192 55 kHz kHz kHz % ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns 2011/03 -8- [AK4425A] Timing Diagram 1/fCLK VIH MCLK VIL tCLKH tCLKL dCLK=tCLKH x fCLK, tCLKL x fCLK 1/fs VIH LRCK VIL tBCK VIH BICK VIL tBCKH tBCKL Figure 1. Clock Timing VIH LRCK VIL tBLR tLRB VIH BICK VIL tSDH tSDS VIH SDTI VIL Figure 2. Serial Interface Timing MS1127-E-01 2011/03 -9- [AK4425A] VIH CSN VIL tCSS tCCKL tCCKH VIH CCLK VIL tCDS C1 CDTI tCDH C0 R/W A4 VIH VIL Figure 3. WRITE Command Input Timing tCSW VIH CSN VIL tCSH VIH CCLK CDTI VIL D3 D2 D1 D0 VIH VIL Figure 4. WRITE Data Input Timing MS1127-E-01 2011/03 - 10 - [AK4425A] OPERATION OVERVIEW System Clock The external clocks required to operate the AK4425A are MCLK, LRCK and BICK. The master clock (MCLK) should be synchronized with LRCK but the phase is not critical. The MCLK is used to operate the digital interpolation filter and the delta-sigma modulator. The MCLK is used to operate the digital interpolation filter and the delta-sigma modulator. There are two methods to set MCLK frequency. In Manual Setting Mode (ACKS = "0": Register 00H), the sampling speed is set by DFS0/1 (Table 1). The frequency of MCLK at each sampling speed is set automatically. (Table 2) When the power applied, the AK4425A is in Auto Setting Mode. In Auto Setting Mode (ACKS = "1": Default), as MCLK frequency is detected automatically (Table 3), and the internal master clock becomes the appropriate frequency (Table 4), it is not necessary to set DFS0/1. The AK4425A is automatically placed in power saving mode when MCLK, LRCK and BICK stop during normal operation mode, and the analog output is forced to 0V(typ). When MCLK, LRCK and BICK are input again, the AK4425A is powered up. After power-up, the AK4425A is in the power-down mode until MCLK, LRCK and BICK are input. DFS1 0 0 1 DFS1 0 0 0 0 0 1 1 DFS0 0 0 0 1 1 0 0 Sampling Speed Normal Double Quad DFS0 Sampling Rate (fs) 0 Normal Speed Mode 8kHz~48kHz 1 Double Speed Mode 60kHz~96kHz 0 Quad Speed Mode 120kHz~192kHz Table 1. Sampling Speed (Manual Setting Mode) LRCK (kHz) fs 32.0 44.1 48.0 88.2 96.0 176.4 192.0 (default) MCLK (MHz) 128fs 11.2896 12.2880 22.5792 24.5760 192fs 16.9344 18.4320 33.8688 36.8640 256fs 8.1920 11.2896 12.2880 22.5792 24.5760 - 384fs 12.2880 16.9344 18.4320 33.8688 36.8640 - 512fs 16.3840 22.5792 24.5760 - 768fs 24.5760 33.8688 36.8640 - 1152fs 36.8640 - BICK (MHz) 64fs 2.0480 2.8224 3.0720 5.6448 6.1440 11.2896 12.2880 Table 2. System Clock Example MCLK Sampling Speed 1152fs Normal (fs=32kHz only) 512fs 768fs Normal 256fs 384fs Double 128fs 192fs Quad Table 3. Sampling Speed(Auto Setting Mode: Default) MS1127-E-01 2011/03 - 11 - [AK4425A] LRCK fs 32.0kHz 44.1kHz 48.0kHz 32.0kHz 44.1kHz 48.0kHz 88.2kHz 96.0kHz 176.4kHz 192.0kHz 128fs - 22.5792 24.5760 MCLK (MHz) 256fs 384fs 512fs 768fs 16.3840 24.5760 22.5792 33.8688 24.5760 36.8640 8.192 12.288 11.2896 16.9344 12.288 18.432 22.5792 33.8688 24.5760 36.8640 33.8688 36.8640 Table 4. System Clock Example (Auto Setting Mode) 192fs - 1152fs 36.8640 - Sampling Speed Normal Double - Quad When MCLK= 256fs/384fs, the AK4425A supports sampling rate of 32kHz~96kHz in auto setting mode (Table 4). But, when the sampling rate is 32kHz~48kHz, DR and S/N will degrade by approximately 3dB as compared to when MCLK= 512fs/768fs. MCLK 256fs/384fs 512fs/768fs DR,S/N 103dB 106dB Table 5. Relationship between MCLK frequency and DR, S/N (fs= 44.1kHz) (Auto Setting Mode) Audio Serial Interface Format The audio data is shifted in via the SDTI pin using the BICK and LRCK inputs. The DIF2-0 bit can select within five serial data modes as shown in Table 6. In all modes the serial data is MSB-first, two's complement format and it is latched on the rising edge of BICK. Mode 2 can be used for 16/20 MSB justified formats by zeroing the unused LSBs. Mode 0 1 2 3 4 DIF2 0 0 0 0 1 DIF1 DIF0 SDTI Format BICK 0 0 16bit LSB Justified 32fs 0 1 20bit LSB Justified 40fs 1 0 24bit MSB Justified 48fs 1 1 24bit I2S Compatible 48fs 0 0 24bit LSB Justified 48fs Table 6. Audio Data Format in Serial control mode MS1127-E-01 Figure Figure 5 Figure 6 Figure 7 Figure 8 Figure 6 (default) 2011/03 - 12 - [AK4425A] LRCK 0 1 10 11 12 13 14 15 0 1 10 11 12 13 14 15 0 1 BICK (32fs) SDTI Mode 0 15 14 6 5 1 0 4 14 3 15 2 16 1 17 0 31 15 14 0 6 5 4 14 1 15 3 2 16 1 17 0 31 15 14 0 1 BICK (64fs) SDTI Mode 0 Don't care 15 14 0 Don't care 15 14 0 15:MSB, 0:LSB Lch Data Rch Data Figure 5. Mode 0 Timing LRCK 0 1 8 9 10 11 12 31 0 1 8 9 10 11 12 31 0 1 0 1 BICK (64fs) SDTI Mode 1 Don't care 19 0 Don't care 19 0 Don't care 19 0 19 0 19:MSB, 0:LSB SDTI Mode 4 Don't care 23 22 21 20 23 22 20 21 23:MSB, 0:LSB Lch Data Rch Data Figure 6. Mode 1/4 Timing LRCK 0 1 2 22 23 24 30 31 0 1 2 22 23 24 30 31 BICK (64fs) SDTI 23 22 1 0 Don't care 23 22 1 0 Don't care 23 22 23:MSB, 0:LSB Lch Data Rch Data Figure 7. Mode 2 Timing MS1127-E-01 2011/03 - 13 - [AK4425A] LRCK 0 1 2 3 23 24 25 31 0 1 2 3 23 24 25 31 0 1 BICK (64fs) SDTI 23 22 1 0 Don't care 23 22 1 0 Don't care 23 23:MSB, 0:LSB Lch Data Rch Data Figure 8. Mode 3 Timing MS1127-E-01 2011/03 - 14 - [AK4425A] De-emphasis Filter A digital de-emphasis filter is available for 32, 44.1 or 48kHz sampling rates (tc = 50/15s) and it is enabled or disabled by DEM0 and DEM1. In case of double speed and quad speed mode, the digital de-emphasis filter is always OFF. DEM1 DEM0 Mode 0 0 44.1kHz (default) 0 1 OFF 1 0 48kHz 1 1 32kHz Table 7. De-emphasis Filter Control (Normal Speed Mode) Analog Output Block The internal negative power supply generation circuit (Figure 9) provides a negative power supply for the internal 2Vrms amplifier. It allows the AK4425A to output an audio signal centered at VSS (0V, typ) as shown in Figure 10. The negative power generation circuit (Figure 9) needs 1.0uF capacitors (Ca, Cb) with low ESR (Equivalent Series Resistance). If this capacitor is polarized, the positive polarity pin should be connected to the CP and VSS1 pins. This circuit operates by clocks generated from MCLK. When MCLK stops, the AK4425A is placed in the reset mode automatically and the analog outputs settle to VSS (0V, typ). AK4425 VDD Charge Pump CP Negative Power CN VSS1 (+) 1uF Ca VEE Cb 1uF (+) Figure 9. Negative Power Generation Circuit AK4425 2.2Vrms 0V AOUTR (AOUTL) Figure 10. Audio Signal Output MS1127-E-01 2011/03 - 15 - [AK4425A] Output Volume The AK4425A includes channel independent digital output volumes (ATT) with 256 levels at linear step including MUTE. These volumes are in front of the DAC and can attenuate the input data from 0dB to -48dB and mute. When changing levels, transitions are executed via soft changes; thus no switching noise occurs during these transitions. The transition time of 1 level and all 256 levels is shown in Table 8. Transition Time 1 Level 255 to 0 Normal Speed Mode 4LRCK 1020LRCK Double Speed Mode 8LRCK 2040LRCK Quad Speed Mode 16LRCK 4080LRCK Table 8. ATT Transition Time Sampling Speed Soft Mute Operation Soft mute operation is performed in digital domain. When the SMUTE bit is set to "1", the output signal is attenuated by - during ATT_DATAxATT transition time (Table 8) from the current ATT level. When the SMUTE bit is returned to "0", the mute is cancelled and the output attenuation gradually changes to the ATT level during ATT_DATAxATT transition time. If the soft mute is cancelled before attenuating to -, the attenuation is discontinued and returned to ATT level by the same cycle. The soft mute is effective for changing the signal source without stopping the signal transmission. SMUTE bit ATT Level (1) (1) (3) Attenuation - GD (2) GD AOUT Notes: (1) ATT_DATAxATT transition time (Table 8). For example, in Normal Speed Mode, this time is 1020LRCK cycles (1020/fs) at ATT_DATA=255. (2) The analog output corresponding to the digital input has group delay, GD. (3) If the soft mute is cancelled before attenuating to - after starting the operation, the attenuation is discontinued and returned to ATT level by the same cycle. Figure 11. Soft Mute function MS1127-E-01 2011/03 - 16 - [AK4425A] System Reset The AK4425A is in power down mode upon power-up. The MLCK should be input after the power supplies are ramped up. The AK4425A is in power-down mode until LRCK are input. tW<20ms Power Supply 0.8xVDD (VDD, AVDD) 0.3V (1) Low MCLK 20 s Reset Release (3) Internal Reset Reset 50ms(max) )(2) Audio circuit Power-up 2, 3 LRCK Clocks (4) Charge Pump Circuit Power-up Power down Time A VEE Pin 0V (5) "0" data D/A In (Digital) 0V D/A Out (Analog) Active (D/A Out) MUTE (D/A Out) Notes: (1) The AK4425A includes an internal Power on Reset Circuit which is used reset the digital logic into a default state after power up. Therefore, the power supply voltage must reach 80% VDD from 0.3V in less than 20msec. (2) Register writings are valid after 50ms (max). (3) When internal reset is released, approximately 20us after a MCLK input, the internal analog circuit is powered-up. (4) The digital circuit and charge pump circuit are powered-up in 2, 3 LRCK cycle when the analog circuit is powered-up. (5) The charge pump counter starts after the charge pump circuit is powered-up. The DAC outputs a valid analog signal after Time A. Time A = 1024/(fs x 16): Normal speed mode Time A = 1024/(fs x 8): Double speed mode Time A = 1024/(fs x 4): Quad speed mode Figure 12. System Reset Diagram MS1127-E-01 2011/03 - 17 - [AK4425A] Reset Function When the MCLK, LRCK or BICK stops, the AK4425A is placed in reset mode and its analog outputs are set to VSS (0V, typ). When the MCLK, LRCK and BICK are restarted, the AK4425A returns to normal operation mode. Internal State Normal Operation Reset D/A In (Digital) Normal Operation (1) GD D/A Out (Analog) (3) VSS (2) (3) <Case1:MCLK Stop> Clock In (4) MCLK Stop MCLK, BICK, LRCK <Case2:LRCK Stop> Clock In (4) LRCK Stop MCLK, BICK, LRCK <Case3:BICK Stop> Clock In (4) BICK Stop MCLK, BICK, LRCK Notes: (1) Digital data can be stopped. The click noise after MCLK, LRCK and BICK are input again can be reduced by inputting the "0" data during this period. (2) The analog output corresponding to a specific digital input has group delay (GD). (3) No audible click noise occurs under normal conditions. (4) Clocks (MCLK, BICK, LRCK) can be stopped in the reset mode (MCLK or LRCK is stopped). Figure 13. Reset Timing Example MS1127-E-01 2011/03 - 18 - [AK4425A] Mode Control Interface The function of the AK4425A can be controlled by register settings. The register can be accessed 50msec(max) after power up the AK4425A. Internal registers may be written to 3-wire P interface pins, CSN, CCLK and CDTI. The data on this interface consists of Chip Address (2bits, C1/0; fixed to "01"), Read/Write (1bit; fixed to "1", Write only), Register Address (MSB first, 5bits) and Control Data (MSB first, 8bits). Address and data are clocked in on the rising edge of CCLK. For write operations, the data is latched after a low-to-high transition of the 16th CCLK. The clock speed of CCLK is 5MHz(max). CSN 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 CCLK CDTI C1 C0 R/W A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 C1-C0: R/W: A4-A0: D7-D0: Chip Address (Fixed to "01") READ/WRITE (Fixed to "1", Write only) Register Address Control Data Figure 14. 3-wire Serial Control I/F Timing MS1127-E-01 2011/03 - 19 - [AK4425A] Register Map Addr Register Name D7 D6 D5 D4 D3 D2 D1 D0 00H 01H 02H 03H 04H Notes: Control 1 Control 2 Control 3 Lch ATT Rch ATT ACKS 0 RRST ATT7 ATT7 0 0 0 ATT6 ATT6 0 SLOW 0 ATT5 ATT5 DIF2 DFS1 INVL ATT4 ATT4 DIF1 DFS0 INVR ATT3 ATT3 DIF0 DEM1 0 ATT2 ATT2 PW DEM0 0 ATT1 ATT1 RSTN SMUTE 0 ATT0 ATT0 Do not write any data to the register over 05H directly. Writing "1" to D7 and D6 of Addr01H and D2 of Addr02H is ignored. The bits defined as 0 must contain a "0" value. When RSTN bit goes "0", the only internal timing is reset and the registers are not initialized to their default values. All data can be written to the register even if PW or RSTN bit is "0". Do not write the registers within 50msec after the power supplies are fed. MS1127-E-01 2011/03 - 20 - [AK4425A] Register Definitions Addr 00H Register Name D7 D6 D5 D4 D3 D2 D1 D0 Control 1 ACKS 0 0 DIF2 DIF1 DIF0 PW RSTN default 1 0 0 0 1 0 1 1 RSTN: Internal timing reset control 0: Reset. All registers are not initialized. 1: Normal Operation The click noise, which occurs when MCLK frequency or DFS is changed, can be reduced by RSTN bit. PW: Power down control 0: Power down. All registers are not initialized. 1: Normal Operation DIF2-0: Audio data interface formats (Table 6) Initial: "010", Mode 2 ACKS: Master Clock Frequency Auto Setting Mode Enable 0: Disable, Manual Setting Mode 1: Enable, Auto Setting Mode Master clock frequency is detected automatically at ACKS bit "1". In this case, the settings of DFS1-0 are ignored. When this bit is "0", DFS1-0 set the sampling speed mode. Addr 01H Register Name D7 D6 D5 D4 D3 D2 D1 D0 Control 2 0 0 SLOW DFS1 DFS0 DEM1 DEM0 SMUTE default 0 0 0 0 0 0 1 0 SMUTE: Soft Mute Enable 0: Normal operation 1: DAC outputs soft muted DEM1-0: De-emphasis Response (Table 7) Initial: "01", OFF DFS1-0: Sampling speed control 00: Normal Speed Mode 01: Double Speed Mode 10: Quad Speed Mode When changing between Normal/Double Speed Mode and Quad Speed Mode, some click noise occurs. SLOW: Slow Roll-off Filter Enable 0: Sharp Roll-off Filter 1: Slow Roll-off Filter MS1127-E-01 2011/03 - 21 - [AK4425A] Addr 02H D7 D6 D5 D4 D3 D2 D1 D0 Control 3 Register Name RRST 0 0 INVL INVR 0 0 0 default 0 0 0 0 0 0 0 0 D5 ATT5 ATT5 1 D4 ATT4 ATT4 1 D3 ATT3 ATT3 1 D2 ATT2 ATT2 1 D1 ATT1 ATT1 1 D0 ATT0 ATT0 1 INVR: Inverting Lch Output Polarity 0: Normal Output 1: Inverted Output INVL: Inverting Rch Output Polarity 0: Normal Output 1: Inverted Output RRST: Register Reset 0: Normal Operation 1: Register Reset (except RRST bit) Addr 03H 04H Register Name Lch ATT Rch ATT default D7 ATT7 ATT7 1 D6 ATT6 ATT6 1 ATT = 20 log10 (ATT_DATA / 255) [dB] 00H: Mute MS1127-E-01 2011/03 - 22 - [AK4425A] SYSTEM DESIGN Figure 15 shows the system connection diagram. An evaluation board (AKD4425) is available for fast evaluation as well as suggestions for peripheral circuitry. Analog 5.0V 0.1u + 10u VDD Master Clock 2 MCLK CP 15 + VSS1 16 1 + 64fs 3 BICK CN 14 1u (1) 1u (1) 24bit Audio Data 4 SDTI VEE 13 fs 5 LRCK 6 CSN VSS2 11 7 CCLK AVDD 10 8 CDTI P Digital Ground AK4425AAOUTL AOUTR 12 Lch Out 0.1u + 10u 9 Rch Out Analog Ground Note: Use low ESR (Equivalent Series Resistance) capacitors. When using polarized capacitors, the positive polarity pin should be connected to the CP and VSS1 pin. VSS1 and VSS2 should be separated from digital system ground. Digital input pins should not be allowed to float. Figure 15. Typical Connection Diagram MS1127-E-01 2011/03 - 23 - [AK4425A] 1. Grounding and Power Supply Decoupling VDD and AVDD are supplied from the analog supply and should be separated from the system digital supply. Decoupling capacitors, especially 0.1F ceramic capacitors for high frequency bypass, should be placed as near to VDD and AVDD as possible. The VSS1 and VSS2 must be connected to the same analog ground plane. Power-up sequence between VDD and AVDD is not critical. 2. Analog Outputs The analog outputs are single-ended and centered around the VSS (ground) voltage. The output signal range is typically 2.2Vrms (typ @AVDD=5V). The internal switched-capacitor filter (SCF) and continuous-time filter (CTF) attenuate the noise generated by the delta-sigma modulator beyond the audio passband. Using single a 1st-order LPF (Figure 16) can reduce noise beyond the audio passband. AK4425 470 Analog Out AOUT 2.2nF 2.2Vrms (typ) (fc = 154kHz, gain = -0.28dB @ 40kHz, gain = -1.04dB @ 80kHz) Figure 16. External 1st order LPF Circuit Example MS1127-E-01 2011/03 - 24 - [AK4425A] PACKAGE 16pin TSSOP (Unit: mm) 1.1 (max) *5.00.1 16 9 8 1 0.13 M 6.40.2 *4.40.1 A 0.65 0.220.1 0.170.05 Detail A 0.50.2 0.10.1 Seating Plane 0.10 NOTE: Dimension "*" does not include mold flash. 0-10 Package & Lead frame material Package molding compound: Lead frame material: Lead frame surface treatment: Epoxy, Halogen (bromine and chlorine) free Cu Solder (Pb free) plate MS1127-E-01 2011/03 - 25 - [AK4425A] MARKING AKM 4425AET XXYYY 1) 2) 3) 4) Pin #1 indication Date Code : XXYYY (5 digits) XX: Lot# YYY: Date Code Marketing Code : 4425AET Asahi Kasei Logo REVISION HISTORY Date (YY/MM/DD) 09/09/18 11/03/01 Revision 00 01 Reason First Edition Error Correction Page Contents 24 1. Grounding and Power Supply Decoupling The description was changed. MS1127-E-01 2011/03 - 26 - [AK4425A] IMPORTANT NOTICE z These products and their specifications are subject to change without notice. When you consider any use or application of these products, please make inquiries the sales office of Asahi Kasei Microdevices Corporation (AKM) or authorized distributors as to current status of the products. z Descriptions of external circuits, application circuits, software and other related information contained in this document are provided only to illustrate the operation and application examples of the semiconductor products. You are fully responsible for the incorporation of these external circuits, application circuits, software and other related information in the design of your equipments. AKM assumes no responsibility for any losses incurred by you or third parties arising from the use of these information herein. AKM assumes no liability for infringement of any patent, intellectual property, or other rights in the application or use of such information contained herein. z Any export of these products, or devices or systems containing them, may require an export license or other official approval under the law and regulations of the country of export pertaining to customs and tariffs, currency exchange, or strategic materials. z AKM products are neither intended nor authorized for use as critical componentsNote1) in any safety, life support, or other hazard related device or systemNote2), and AKM assumes no responsibility for such use, except for the use approved with the express written consent by Representative Director of AKM. As used here: Note1) A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability. Note2) A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property. z It is the responsibility of the buyer or distributor of AKM products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the above content and conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold AKM harmless from any and all claims arising from the use of said product in the absence of such notification. MS1127-E-01 2011/03 - 27 -