!Note * This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors Murata Manufacturing Co., Ltd. Cat.No.T13E-12 T13E.pdf 07.3.1 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. CONTENTS 1 Part Numbering 2 Selection Guide of Ceramic Trimmer Capacitor 3 1 TZR1 Series 4 2 TZS2 Series 8 3 TZY2 Series 12 4 TZV2 Series 16 5 TZC3 Series 20 2 3 4 6 TZW4 Series 24 7 TZB4 Series 27 8 TZ03 Series 33 5 Packaging 39 Recommended Adjustment Tools 41 Qualified Standards 43 6 7 8 The Bluetooth trademarks are owned by Bluetooth SIG, Inc., U.S.A. Recycled Paper PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. o Part Numbering Ceramic Trimmer Capacitors (Part Number) TZ Y2 R 200 A 001 R00 q w e r t y u tTerminal Shape qProduct ID Code Product ID TZ Trimmer Capacitors wSeries/Terminal B TZC3, TZW4, TZB4 (SMD Type) Top Adjustment; TZB4 (SMD Type) Code Series/Terminal C Top Adjustment; TZB4 (Lead Type) 03 6mm Size Lead Type D Rear Adjustment; TZB4 (Lead Type) Rear Adjustment; TZB4 (SMD Type) B4 4mm Size SMD/Lead Type E W4 4mm Size SMD Type F Top Adjustment; TZ03 (Lead Type) C3 3mm Size SMD Type N Rear Adjustment; TZ03 (Lead Type) S2 2mm Size SMD Type (Height 1.0mm) Y2 2mm Size SMD Type (Height 1.25mm) V2 2mm Size SMD Type (Height 1.45mm) R1 1mm Size SMD Type (Height 0.90mm) eTemperature Characteristics Please refer to dimensions for terminals in detail. yIndividual Specification Code Individual Specifications 001 TZR1, TZS2, TZY2, TZW4 Standard Type 110 TZV2, TZC3 (Minus Slot) Standard Type Code Temperature Characteristics 169 TZ03 Standard Type Z NP0ppm/C 310 TZC3 (Plus Slot) Standard Type N N200ppm/C A10 TZB4 No-cover Film Standard Type T N450ppm/C B10 TZB4 with Cover Film Standard Type R N750ppm/C K N1000ppm/C P N1200ppm/C Please refer to ratings for tolerance of temperature characteristics. rMaximum Capacitance Expressed by three-digit alphanumerics. The unit is pico-farad (pF). The first and second figures are significant digits, and the third figure expresses the number of zeros which follow the two numbers. If there is a decimal point, it is expressed by the capital letter "R". In this case, all figures are significant digits. 2 A Terminal Shape Top Adjustment; TZR1, TZS2, TZY2, TZV2, uPackaging Code Packaging B00 Bulk R00 Reel (Taping o180mm) R01 Reel (Taping o330mm) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Selection Guide of Ceramic Trimmer Capacitor Start Mounting Method Surface Mount PCB Insertion Soldering Method Reflow Height 0.90mm max. 1.5(W) x 1.7(L) Height 1.7mm max. 3.2(W) x 4.5(L) TZR1 TZC3 Height 1.00mm max. 2.2(W) x 2.7(L) Height 1.8mm max. 3.2(W) x 4.5(L) TZS2 TZC3 Height 1.25mm max. 2.5(W) x 3.2(L) Height 3.2mm max. 4.0(W) x 4.5(L) TZY2 TZB4_A Flow Manual Insertion Height 3.2mm max. 4.0(W) x 4.5(L) Height 3.2mm max. 4.0(W) x 4.5(L) TZB4_A (with cover film) TZB4_C TZB4_B TZB4_D (with cover film) Height 5.3mm max. 6.0(W) x 6.0(L) TZB4_E (with cover film) TZ03_F Height 1.45mm max. 2.3(W) x 3.2(L) TZB4_B TZ03_N TZV2 TZB4_E High Frequency Power Height 2.6mm max. 4.2(W) x 5.2(L) TZW4 All products of Ceramic Trimmer Capacitor comply with RoHS and ELV 3 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors 1 TZR1 Series 1.7 Features 0.9 max. 1.5 (Depth;0.15) 0.45 0.2 1. Ultra-small and thin with external dimensions of 1.5(W)x1.7(L)x0.85(H)mm (80% less in volume than the current product). 2. Unique construction with no plastic material provides superior soldering heat resistance to maintain excellent characteristic performance after reflow soldering. 3. Suitable for high frequency circuit due to high self resonant frequency (6.2GHz of TZR1Z010 at 1.0pF setting) 0.35 ( Tolerance:in 0.1 mm ) Applications 1. "Bluetooth" 2. Crystal oscillators 3. Crystal filters 4. Hand radios 5. Miniature tuner packs (FM Radio, TV) 6. Remote keyless entry systems 7. Pagers Cmin. (max.) (pF) Cmax. (pF) TC Q Rated Voltage Withstanding Voltage TZR1Z010A001 0.55 1.0 +100/-0% NP0300ppm/C 200min. at 200MHz, Cmax. 25Vdc 55Vdc TZR1Z1R5A001 0.7 1.5 +100/-0% NP0300ppm/C 200min. at 200MHz, Cmax. 25Vdc 55Vdc TZR1Z040A001 1.5 4.0 +100/-0% NP0500ppm/C 300min. at 1MHz, Cmax. 25Vdc 55Vdc TZR1R080A001 3.0 8.0 +100/-0% N750500ppm/C 300min. at 1MHz, Cmax. 25Vdc 55Vdc Part Number Insulation Resistance: 10000M ohm Torque: 0.1 to 1.0mNm Operating Temperature Range: -25 to +85C Construction Cover Metal Rotor Monolithic Stator 4 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Temperature Characteristics TZR1Z010 -25 0 -10 Z1R5 (NP0300 ppm/C) Cap. Change (%) Cap. Change (%) Z010 (NP0300 ppm/C) +8 +6 +4 +2 65 0 85 0 -10 45 -4 +8 +6 +4 +2 45 -4 Temp. (C) Temp. (C) -6 -8 -8 -10 -10 -12 -12 TZR1Z040 TZR1R080 R080 (N750500 ppm/C) Cap.Change (%) Cap.Change (%) Z040 (NP0500 ppm/C) +8 +6 +4 +2 0 -2 +6 +4 20 Temp.(C) +2 20 -25 -10 45 85 65 0 -2 0 45 -4 +8 85 65 0 -10 85 20 -2 -6 -25 65 0 -25 20 -2 1 TZR1Z1R5 -4 Temp.(C) -6 -6 -8 -8 -10 -10 -12 -12 Frequency Characteristics TZR1Z010 TZR1Z1R5 Z010 10000 10000 1000 1000 100 Z1R5 100 0.55pF set 0.7pF set Q Q 10 10 1.0pF set 1.5pF set 1 2 4 6 Frequency (GHz) 8 2 4 6 Frequency (GHz) TZR1R080 Z040 R080 1000 100 1000 100 Q 10 10 500 0 TZR1Z040 1000 1 0 10 1000 1500 2000 Frequency (MHz) 2500 8 10 1000 100 100 10 10 Q 1 500 1000 1500 Frequency (MHz) Capacitance(pF) 0 Capacitance(pF) 0 1 2000 Continued on the following page. 5 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Land Pattern 2.2 0.5 1.2 Tolerance: 0.1 in mm Temperature Profile Reflow Soldering Profile qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu) wSoldering profile for Eutectic solder (63Sn/37Pb) (Limit profile: refer to q) T5 T4 T3 T2 Temperature (C) Temperature (C) 1 T1 t2 Limit Profile t3 Standard Profile t1 T3 T2 Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T2) 220C Time (t2) Standard Profile t1 time (s) time (s) Standard Profile Standard Profile Pre-heating t2 T1 Peak temperature (T3) Pre-heating Temp. (T1) Time (t1) Temp. (T2) 2time 150C 60 to 120sec. 183C 30 to 60sec. 2453C Time (t2) Peak temperature (T3) Cycle of reflow 30sec. 230 +5/-0C 1time Heating Cycle of reflow Limit Profile Pre-heating Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T4) 230C Time (t3) Peak temperature (T5) Cycle of reflow 30 to 50sec. 260 +5/-0C 2time Solder Iron Standard Profile Temperature of soldering iron tip Soldering time Soldering iron power output Cycle of solder iron 35010C 3sec. max. 30W max. 1time Notice (Storage and Operating Condition) 1. Do not use the trimmer capacitor under atmosphere of RTV silicone rubber (Room Temperature Vulcanizing Silicone Rubber) except Acetone liberating silicone sealant. 2. Before using trimmer capacitor, please store under the condition of -10 to +40 degree C and 30 to 85%RH. 3. Do not store in or near corrosive gasses. 4. Use within 6 months of delivery. 5. Do not store under direct sunlight. 6 6. Do not use the trimmer capacitor under the conditions listed below. (1) Corrosive gasses atmosphere (ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) Dusty / dirty atmosphere (4) Direct sunlight (5) Static voltage nor electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Soldering and Mounting) 1. Soldering (1) TZR1 series can be soldered by reflow soldering method and soldering iron. Do not use flow soldering method (dipping). (2) Soldering condition Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (3) The amount of solder is critical. (4) The thickness of solder paste should be printed from 100 micro m to 150 micro m and the dimension of land pattern should be Murata's standard land pattern used at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals or contact failure due to flux wicking up. (5) When using soldering iron, the diameter of the string solder shall be less than 0.5mm. The string solder shall be applied to the lower part of the terminal only. Do not apply flux except to the terminals. Excessive amounts of solder and/or applying solder to the upper part of the terminal may cause fixed metal rotor or contact failure due to flux invasion into 1 the movable part and/or the contact point. The soldering iron should not come in contact with the monolithic stator of the trimmer capacitor. If such contact does occur, the trimmer capacitor may be damaged. (6) Our recommended chlorine content of solder is as follows. (a) Solder paste: 0.2wt% max. (b) String solder: 0.5wt% max. (7) Do not use water-soluble flux (for water cleaning). To prevent the deterioration of trimmer capacitor characteristics, apply flux only to terminals. 2. Mounting (1) Do not apply excessive force (preferably 5.0 N [Ref: 500gf] max.), when the trimmer capacitor is mounted on the PCB. (2) Do not warp and/or bend PCB to prevent trimmer capacitor from breaking. (3) Use the suitable dimension of the pick-up nozzle. (1.1-1.2mm external diameter and 0.8-0.9mm bore diameter.) 3. Cleaning Cannot be cleaned because of open construction. 4. Other Note the polarity of the trimmer capacitor to minimize influence by stray capacitance. (Refer to the dimensions concerning the polarity.) Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in driver slot. *Recommended screwdriver for manual adjustment MURATA: KMDR160 2. When adjusting with a screwdriver, do not apply excessive force (preferably 0.5 N [Ref: 50gf] max.) to minimize capacitance drift. If excessive force is applied to the screwdriver slot, it may cause deformation of the products. 3. Do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. They may cause corrosion or electrical contact problems. Notice (Other) Before using trimmer capacitor, please test after assembly in your particular mass production system. 7 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors TZS2 Series 2.7 2.2 1. Ultra-small and thin type with external dimensions of 2.2(W)x2.7(L)x0.95(H)mm (30% less in volume from the current product). 2. Unique construction with no plastic material provides superior soldering heat resistance to maintain excellent characteristic performance after reflow soldering. 3. Pierced square hole allows for high resistance to tuning force and in-process automatic adjustment. 1.0 0.6 0.20 Depth Features 1.0max. 2 0.4 Tolerance: 0.1 in mm Applications 1. Crystal oscillators 2. Crystal filters 3. Hand radios 4. Cordless telephones 5. Cellular telephones 6. Tuner packs 7. Pagers 8. Remote keyless entry systems 9. PHS 10. Radar detectors 11. W-LAN 12. Compact radios 13. Headphone stereos Part Number Cmin. (max.) (pF) Cmax. (pF) TC Q Rated Voltage Withstanding Voltage TZS2Z060A001 3.0 6.0 +100/-0% NP0300ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc TZS2Z100A001 3.5 10.0 +100/-0% NP0300ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc TZS2R200A001 7.0 20.0 +100/-0% N750500ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc Insulation Resistance: 10000M ohm Torque: 0.7 to 4.9mNm Operating Temperature Range: -25 to +85C Construction Cover Metal Rotor Monolithic Stator 8 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Temperature Characteristics TZS2Z060 TZS2Z100 Z100 (NP0300 ppm/C) Cap.Change (%) Cap.Change (%) Z060 (NP0300 ppm/C) +8 +6 +4 +2 65 0 -25 -10 +4 -10 45 0 65 20 -2 2 Temp.(C) 0 -25 -4 +6 +2 85 20 -2 0 +8 85 45 -4 Temp.(C) -6 -6 -8 -8 -10 -10 -12 -12 TZS2R200 Cap.Change (%) R200 (N750500 ppm/C) +8 +6 +4 +2 20 -25 -10 0 Temp.(C) 45 65 85 0 -2 -4 -6 -8 -10 -12 Frequency Characteristics TZS2Z060 TZS2Z100 Z100 1000 100 100 Q 10 1 10 1000 1000 100 100 10 10 Q Capacitance (pF) 1000 Capacitance (pF) Z060 1 500 1000 1500 Frequency (MHz) 2000 200 400 600 800 1000 Frequency (MHz) Continued on the following page. 9 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Frequency Characteristics TZS2R200 R200 1000 1000 100 100 10 10 2 Capacitance (pF) Q 1 200 400 600 800 1000 Frequency (MHz) Land Pattern 3.2 1.0 2.1 Tolerance: 0.1 in mm Temperature Profile Reflow Soldering Profile wSoldering profile for Eutectic solder (63Sn/37Pb) (Limit profile: refer to q) T5 T4 T3 T2 Temperature (C) Temperature (C) qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu) T1 t2 Limit Profile t3 Standard Profile t1 T3 T2 Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T2) 220C Time (t2) Standard Profile t1 time (s) time (s) Standard Profile Standard Profile Pre-heating t2 T1 Peak temperature (T3) Cycle of reflow Temp. (T1) Time (t1) Temp. (T2) Time (t2) Peak temperature (T3) Cycle of reflow 2time 150C 60 to 120sec. 183C 30sec. 230 +5/-0C 1time 30 to 60sec. 2453C Pre-heating Heating Limit Profile Pre-heating Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T4) 230C Time (t3) Peak temperature (T5) Cycle of reflow 30 to 50sec. 260 +5/-0C 2time Solder Iron Standard Profile 10 Temperature of soldering iron tip Soldering time Soldering iron power output Cycle of solder iron 35010C 3sec. max. 30W max. 1time PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Storage and Operating Condition) 1. Do not use the trimmer capacitor under atmosphere of RTV silicone rubber (Room Temperature Vulcanizing Silicone Rubber) except Acetone liberating silicone sealant. 2. Before using trimmer capacitor, please store under the condition of -10 to +40 degree C and 30 to 85%RH. 3. Do not store in or near corrosive gasses. 4. Use within 6 months of delivery. 5. Do not store under direct sunlight. 6. Do not use the trimmer capacitor under the conditions listed below. (1) Corrosive gasses atmosphere (ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) Dusty / dirty atmosphere (4) Direct sunlight (5) Static voltage nor electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above 2 Notice (Soldering and Mounting) 1. Soldering (1) TZS2 series can be soldered by reflow soldering method and soldering iron. Do not use flow soldering method (dipping). (2) Soldering condition Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (3) The amount of solder is critical. (4) The thickness of solder paste should be printed from 100 micro m to 150 micro m and the dimension of land pattern should be Murata's standard land pattern used at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals or contact failure due to flux wicking up. (5) When using soldering iron, the diameter of the string solder shall be less than 0.5mm. The string solder shall be applied to the lower part of the terminal only. Do not apply flux except to the terminals. Excessive amounts of solder and/or applying solder to the upper part of the terminal may cause fixed metal rotor or contact failure due to flux invasion into the movable part and/or the contact point. The soldering iron should not come in contact with the monolithic stator of the trimmer capacitor. If such contact does occur, the trimmer capacitor may be damaged. (6) Our recommended chlorine content of solder is as follows. (a) Solder paste: 0.2wt% max. (b) String solder: 0.5wt% max. (7) Do not use water-soluble flux (for water cleaning). To prevent the deterioration of trimmer capacitor characteristics, apply flux only to terminals. 2. Mounting (1) Do not apply excessive force (preferably 5.0 N [Ref: 500gf] max.), when the trimmer capacitor is mounted on the PCB. (2) Do not warp and/or bend PCB to prevent trimmer capacitor from breakage. (3) Use the suitable dimension of the pick-up nozzle (1.8mm external diameter and 1.3mm bore diameter). 3. Cleaning Cannot be cleaned because of open construction. 4. Other Note the polarity of the trimmer capacitor to minimize influence by stray capacitance. (Refer to the dimensions concerning the polarity.) Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in driver slot. (1) Recommended screwdriver for manual adjustment MURATA: KMDR050 (2) Recommended screwdriver bit for automatic adjustment MURATA: KMBT050 2. When adjusting with a screwdriver, do not apply excessive force (preferably 1.0 N [Ref: 100gf] max.) to minimize capacitance drift. If excessive force is applied to the screwdriver slot, it may cause deformation of the products. 3. Do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. They may cause corrosion or electrical contact problems. Notice (Other) Before using trimmer capacitor, please test after assembly in your particular mass production system. 11 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors TZY2 Series 3.20.2 Features 1.0 0.95 1.25max. 2.50.2 1. Small and thin size with external dimensions of 2.5(W)x3.2(L)x1.25max.(H)mm 2. New shape of cover can improve the flux invasion compared with current products. 3. Improvement of the adhesion between rotor and stator leads to superior stability. 4. Unique construction with no plastic material provides superior soldering heat resistance to maintain excellent characteristic performance after reflow soldering. 5. Suitable for high frequency circuit due to high self resonant frequency (4.8GHz of TZY2Z010 at 1.0pF setting) 0.5 1.4 3 0.45 (Tolerance:in0.1 mm) Applications 1. Crystal oscillators 2. Crystal filters 3. Pagers 4. Cordless telephones 5. PHS 6. Hand radios 7. Cellular telephones 8. Watches 9. Remote keyless entry systems 10. W-LAN 11. Radar detectors 12. Compact radios 13. DVD 14. Burglarproof devices 15. Headphone stereos Cmin. (max.) (pF) Cmax. (pF) TC Q Rated Voltage Withstanding Voltage TZY2Z010A001 0.5 1.0 +100/-0% NP0300ppm/C 200min. at 200MHz, Cmax. 25Vdc 55Vdc TZY2Z2R5A001 0.65 2.5 +100/-0% NP0300ppm/C 200min. at 200MHz, Cmax. 25Vdc 55Vdc TZY2Z030A001 1.5 3.0 +100/-0% NP0300ppm/C 300min. at 1MHz, Cmax. 25Vdc 55Vdc TZY2Z060A001 2.5 6.0 +100/-0% NP0300ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc TZY2Z100A001 3.0 10.0 +100/-0% NP0300ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc TZY2R200A001 4.5 20.0 +100/-0% N750500ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc TZY2R250A001 5.5 25.0 +100/-0% N750500ppm/C 300min. at 1MHz, Cmax. 25Vdc 55Vdc TZY2K450A001 8.0 45.0 +100/-0% N1000500ppm/C 300min. at 1MHz, Cmax. 25Vdc 55Vdc Part Number Insulation Resistance: 10000M ohm Torque: 0.7 to 4.9mNm Construction Cover Metal Rotor Monolithic Stator 12 Operating Temperature Range: -25 to +85C PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Temperature Characteristics TZY2Z010 TZY2Z100 Z100 (NP0300 ppm/C) Cap.Change (%) Cap. Change (%) Z010 (NP0300 ppm/C) +8 +6 +4 +2 -10 0 +4 +2 Temp.(C) 0 65 20 -2 +6 Temp. (C) 0 -25 +8 85 -25 45 -10 -4 -2 0 65 20 85 45 -4 -6 -6 -8 -8 -10 -10 -12 -12 3 TZY2R200 TZY2K450 K450 (N1000500ppm/C) +8 +6 +4 Temp.(C) +2 20 -25 -10 45 65 +10 +8 +6 +4 +2 20 85 0 -2 0 +12 Cap. Change (%) Cap.Change (%) R200 (N750500 ppm/C) 25 0 -4 45 65 Temp. (C) 85 0 -2 -4 -6 -6 -8 -10 -8 -12 -10 -12 Frequency Characteristics TZY2Z010 TZY2Z100 Z010 Z100 1000 1000 100 100 10 10 1000 100 Q 0.5pF set Capacitance (pF) Q 10 1.0pF set 1 0 2 4 Frequency (GHz) 6 8 1 200 400 600 800 1000 Frequency (MHz) Continued on the following page. 13 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Frequency Characteristics TZY2R200 TZY2K450 R200 K450 1000 100 100 Capacitance (pF) Q 10 3 1 1000 1000 100 100 10 10 Capacitance (pF) 1000 Q 10 200 400 600 800 1 1000 200 400 600 800 Frequency (MHz) Frequency (MHz) Land Pattern 4.0 1.2 2.4 Tolerance: 0.1 in mm Temperature Profile Reflow Soldering Profile wSoldering profile for Eutectic solder (63Sn/37Pb) (Limit profile: refer to q) T5 T4 T3 T2 Temperature (C) Temperature (C) qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu) T1 t2 Limit Profile t3 Standard Profile t1 T3 T2 Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T2) 220C Time (t2) Standard Profile t1 time (s) time (s) Standard Profile Standard Profile Pre-heating t2 T1 Peak temperature (T3) Cycle of reflow Temp. (T1) Time (t1) Temp. (T2) Time (t2) Peak temperature (T3) Cycle of reflow 2time 150C 60 to 120sec. 183C 30sec. 230 +5/-0C 1time 30 to 60sec. 2453C Pre-heating Heating Limit Profile Pre-heating Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T4) 230C Time (t3) Peak temperature (T5) Cycle of reflow 30 to 50sec. 260 +5/-0C 2time Solder Iron Standard Profile 14 Temperature of soldering iron tip Soldering time Soldering iron power output Cycle of solder iron 35010C 3sec. max. 30W max. 1time PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Storage and Operating Condition) 1. Do not use the trimmer capacitor under atmosphere of RTV silicone rubber (Room Temperature Vulcanizing Silicone Rubber) except Acetone liberating silicone sealant. 2. Before using trimmer capacitor, please store under the condition of -10 to +40 degree C and 30 to 85%RH. 3. Do not store in or near corrosive gasses. 4. Use within 6 months of delivery. 5. Do not store under direct sunlight. 6. Do not use the trimmer capacitor under the conditions listed below. (1) Corrosive gasses atmosphere (ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) Dusty / dirty atmosphere (4) Direct sunlight (5) Static voltage nor electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above 3 Notice (Soldering and Mounting) 1. Soldering (1) TZY2 series can be soldered by reflow soldering method and soldering iron. Do not use flow soldering method (dipping). (2) Soldering condition Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (3) The amount of solder is critical. (4) The thickness of solder paste should be printed from 120 micro m to 170 micro m and the dimension of land pattern should be Murata's standard land pattern used at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals or contact failure due to flux wicking up. (5) When using soldering iron, the diameter of the string solder shall be less than 0.5mm. The string solder shall be applied to the lower part of the terminal only. Do not apply flux except to the terminals. Excessive amounts of solder and/or applying solder to the upper part of the terminal may cause fixed metal rotor or contact failure due to flux invasion into the movable part and/or the contact point. The soldering iron should not come in contact with the monolithic stator of the trimmer capacitor. If such contact does occur, the trimmer capacitor may be damaged. (6) Our recommended chlorine content of solder is as follows. (a) Solder paste: 0.2wt% max. (b) String solder: 0.5wt% max. (7) Do not use water-soluble flux (for water cleaning). To prevent the deterioration of trimmer capacitor characteristics, apply flux only to terminals. 2. Mounting (1) Do not apply excessive force (preferably 5.0 N [Ref: 500gf] max.), when the trimmer capacitor is mounted on the PCB. (2) Do not warp and/or bend PCB to prevent trimmer capacitor from breakage. (3) Use the suitable dimension of the pick-up nozzle (1.8mm external diameter and 1.3mm bore diameter). 3. Cleaning Cannot be cleaned because of open construction. 4. Other Note the polarity of the trimmer capacitor to minimize influence by stray capacitance. (Refer to the dimensions concerning the polarity.) Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in driver slot. (1) Recommended screwdriver for manual adjustment ENGINEER INC.: DA-89 (Murata P/N is KMDR060) (2) Recommended screwdriver bit for automatic adjustment MURATA: KMBT060 2. When adjusting with a screwdriver, do not apply excessive force (preferably 1.0 N [Ref: 100gf] max.) to minimize capacitance drift. If excessive force is applied to the screwdriver slot, it may cause deformation of the products. 3. Do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. They may cause corrosion or electrical contact problems. Notice (Other) Before using trimmer capacitor, please test after assembly in your particular mass production system. 15 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors TZV2 Series 3.20.2 0.5 Depth 0.2 Features 4 1.0 2.30.2 1. Small size with external dimensions of 2.3(W)x3.2(L)x1.45max.(H)mm 2. Unique construction with no plastic material provides superior soldering heat resistance to maintain excellent characteristic performance after reflow soldering. 3. Designed for automatic placement in surface mount applications. 4. Funnel shaped metal case enables in-process automatic adjustment. Marking(6pF) 1.4 1.45max. Marking(10pF) Tolerance: 0.1 in mm Applications 1. Crystal oscillator 3. Hand radios 5. Cellular telephones 7. Pagers 9. PHS 11. W-LAN 13. Headphone stereos 15. Burglarproof devices 2. Crystal filters 4. Cordless telephones 6. Tuner packs 8. Remote keyless entry systems 10. Radar detectors 12. Compact radios 14. DVD Cmin. (max.) (pF) Cmax. (pF) TC Q Rated Voltage Withstanding Voltage TZV2Z2R5A110 0.65 2.5 +100/-0% NP0300ppm/C 200min. at 200MHz, Cmax. 25Vdc 55Vdc TZV2Z030A110 1.5 3.0 +100/-0% NP0300ppm/C 300min. at 1MHz, Cmax. 25Vdc 55Vdc TZV2Z060A110 2.5 6.0 +100/-0% NP0300ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc TZV2Z100A110 3.0 10.0 +100/-0% NP0300ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc TZV2R200A110 4.5 20.0 +100/-0% N750500ppm/C 500min. at 1MHz, Cmax. 25Vdc 55Vdc Part Number Insulation Resistance: 10000M ohm Torque: 1.0 to 9.8mNm Operating Temperature Range: -25 to +85C Construction Cover Spring Washer Metal Rotor Monolithic Stator 16 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Temperature Characteristics TZV2Z2R5 TZV2Z060 Z060 (NP0300 ppm/C) Cap.Change (%) Cap.Change (%) Z2R5 (NP0300 ppm/C) +8 +6 +4 +2 -10 -2 0 +6 +4 +2 Temp.(C) 0 -25 +8 65 20 85 -25 45 -10 -4 -8 -10 -12 -12 TZV2Z100 TZV2R200 R200 (N750500 ppm/C) Cap.Change (%) Cap.Change (%) Z100 (NP0300 ppm/C) +8 +6 +4 +2 +6 +4 +2 20 65 20 -25 85 -10 0 45 4 +8 Temp.(C) 0 -2 Temp.(C) -6 -8 0 45 -4 -10 -10 85 20 -2 0 -6 -25 65 0 Temp.(C) 45 65 85 0 -2 -4 -4 -6 -6 -8 -8 -10 -10 -12 -12 Frequency Characteristics TZV2Z2R5 TZV2Z060 1000 1000 1000 100 100 100 100 10 10 Q 10 10 1 Capacitance (pF) 1000 Q 1 500 1000 1500 2000 Frequency (MHz) 2500 3000 500 1000 1500 Capacitance (pF) Z060 Z2R5 2000 Frequency (MHz) Continued on the following page. 17 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Frequency Characteristics TZV2Z100 TZV2R200 R200 Z100 1000 100 100 10 10 1 1000 100 100 10 10 Q Capacitance (pF) Q 1000 Capacitance (pF) 1000 1 200 400 600 800 1000 200 400 Frequency (MHz) 800 1000 Land Pattern 4.0 1.2 2.4 Tolerance: 0.1 in mm Temperature Profile Reflow Soldering Profile qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu) wSoldering profile for Eutectic solder (63Sn/37Pb) (Limit profile: refer to q) T5 T4 T3 T2 Temperature (C) Temperature (C) 4 600 Frequency (MHz) T1 t2 Limit Profile t3 Standard Profile t1 T3 T2 Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T2) 220C Time (t2) Standard Profile t1 time (s) time (s) Standard Profile Standard Profile Pre-heating t2 T1 Peak temperature (T3) Cycle of reflow Temp. (T1) Time (t1) Temp. (T2) Time (t2) Peak temperature (T3) Cycle of reflow 2time 150C 60 to 120sec. 183C 30sec. 230 +5/-0C 1time 30 to 60sec. 2453C Pre-heating Heating Limit Profile Pre-heating Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T4) 230C Time (t3) Peak temperature (T5) Cycle of reflow 30 to 50sec. 260 +5/-0C 2time Solder Iron Standard Profile 18 Temperature of soldering iron tip Soldering time Soldering iron power output Cycle of solder iron 35010C 3sec. max. 30W max. 1time PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Storage and Operating Condition) 1. Do not use the trimmer capacitor under atmosphere of RTV silicone rubber (Room Temperature Vulcanizing Silicone Rubber) except Acetone liberating silicone sealant. 2. Before using trimmer capacitor, please store under the condition of -10 to +40 degree C and 30 to 85%RH. 3. Do not store in or near corrosive gasses. 4. Use within 6 months of delivery. 5. Do not store under direct sunlight. 6. Do not use the trimmer capacitor under the conditions listed below. (1) Corrosive gasses atmosphere (ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) Dusty / dirty atmosphere (4) Direct sunlight (5) Static voltage nor electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above Notice (Soldering and Mounting) 1. Soldering (1) TZV2 series can be soldered by reflow soldering method and soldering iron. Do not use flow soldering method (dipping). (2) Soldering condition Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (3) The amount of solder is critical. (4) The thickness of solder paste should be printed from 120 micro m to 170 micro m and the dimension of land pattern should be Murata's standard land pattern used at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals or contact failure due to flux wicking up. (5) When using soldering iron, the diameter of the string solder shall be less than 0.5mm. The string solder shall be applied to the lower part of the terminal only. Do not apply flux except to the terminals. Excessive amounts of solder and/or applying solder to the upper part of the terminal may cause fixed metal rotor or contact failure due to flux invasion into the movable part and/or the contact point. The soldering iron should not come in contact with the monolithic stator of the trimmer capacitor. If such contact does occur, the trimmer capacitor may be damaged. (6) Our recommended chlorine content of solder is as follows. (a) Solder paste: 0.2wt% max. (b) String solder: 0.5wt% max. (7) Do not use water-soluble flux (for water cleaning). To prevent the deterioration of trimmer capacitor characteristics, apply flux only to terminals. 2. Mounting (1) Do not apply excessive force (preferably 5.0 N [Ref: 500gf] max.), when the trimmer capacitor is mounted on the PCB. (2) Do not warp and/or bend PCB to prevent trimmer capacitor from breakage. (3) Use the suitable dimension of the pick-up nozzle (1.8mm external diameter and 1.3mm bore diameter). 3. Cleaning Cannot be cleaned because of open construction. 4. Other Note the polarity of the trimmer capacitor to minimize influence by stray capacitance. (Refer to the dimensions concerning the polarity.) 4 Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in driver slot. (1) Recommended screwdriver for manual adjustment VESSEL: No.9000 -0.9x30 (Murata P/N : KMDR020) (2) Recommended screwdriver bit for automatic adjustment MURATA: KMBT020 2. When adjusting with a screwdriver, do not apply excessive force (preferably 1.0 N [Ref: 100gf] max.) to minimize capacitance drift. If excessive force is applied to the screwdriver slot, it may cause deformation of the products. 3. Do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. They may cause corrosion or electrical contact problems. Notice (Other) Before using trimmer capacitor, please test after assembly in your particular mass production system. 19 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors 0.5 2.5 dia. 1.6 0.35 4.5 4.5 Standard Type 0.8 0.6 Tolerance: 0.1 in mm 0.6 0.50.05 Depth 0.40.05 3.2 1. Small size with external dimension of 3.2(W)x4.5(L)x1.6(H)mm (Cross slot type: 1.7(H)mm) 2. Color coded stator permits easy identification of capacitance and reduces mounting errors. 3. Can be adjusted with conventional adjustment tools having a thickness of 0.5mm. 4. Available for cross slot type to provide better adjustability. 5. Providing mechanism to prevent air leak offers better mountability with automatic mounter. (Cross slot type) 6. Designed for automatic placement in surface mount applications. 7. Heat resistant resin withstands reflow soldering temperatures. 3.2 Features 0.8 0.75 TZC3 Series o2.5 4.5 2. Headphone stereos 4. Portable radio equipments 6. Cellular telephones 8. Remote keyless entry systems Cross Slot Type 0.8 1. Compact radios 3. Pagers 5. Hybrid ICs 7. Cordless telephones 0.75 5 1.7 Applications 0.6 Rated Withstanding Voltage Voltage Tolerance: 0.1 in mm 0.6 Part Number Cmin. (max.) (pF) Cmax. (pF) TC Q TZC3Z030Appp 1.4 3.0 +50/-0% NP0300ppm/C 300min. at 1MHz, Cmax. 100Vdc 220Vdc TZC3Z060Appp 2.0 6.0 +50/-0% NP0300ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue TZC3R100Appp 3.0 10.0 +50/-0% N750300ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc White TZC3P200Appp 5.0 20.0 +50/-0% N1200500ppm/C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Red TZC3P300Appp 6.5 30.0 +50/-0% N1200500ppm/C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Green Stator/Case Color Brown Insulation Resistance: 10000M ohm Torque: 1.5 to 9.8mNm Operating Temperature Range: -25 to +85C The last three digits show the slot type. 110: standard (minus) type, 310 : cross slot type. Construction Standard Type Cross Slot Type Center axis Center axis Rotor spring terminal Rotor spring terminal Ceramic plate Ceramic plate Stator (One molded injection with stator terminal) Stator (One molded injection with stator terminal) Stator terminal Stator terminal Continued on the following page. 20 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Temperature Characteristics TZC3Z030 TZC3Z060 Z060 (NP0300 ppm/C) +8 +6 +4 Temp.(C) +2 0 -25 -10 0 Cap.Change (%) Cap.Change (%) Z030 (NP0300 ppm/C) -2 20 45 85 -25 65 -10 0 -4 -6 -6 -8 -8 -10 -10 -12 -12 20 45 65 85 P200 (N1200500ppm/C) Cap.Change (%) Cap.Change (%) Temp.(C) TZC3P200 +8 +6 +4 +2 0 0 +4 +2 0 -2 TZC3R100 -10 +6 -4 R100 (N750300 ppm/C) -25 +8 45 20 -2 65 +8 +6 +4 +2 0 85 Temp.(C) -25 -10 0 45 65 20 -2 -4 -4 -6 -6 -8 -8 -10 -10 -12 -12 85 Temp.(C) 5 Frequency Characteristics TZC3Z030 TZC3Z060 1000 100 100 10 10 1 Capacitance (pF) Q 1000 Q 1000 1000 100 100 10 10 Capacitance (pF) Z060 Z030 1 100 500 1000 1500 Frequency (MHz) 2000 100 500 1000 1500 2000 Frequency (MHz) Continued on the following page. 21 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Frequency Characteristics TZC3R100 TZC3P200 R100 1000 100 100 10 10 Q 1000 1000 100 100 10 10 Capacitance (pF) 1000 Capacitance (pF) Q P200 1 1 200 400 600 800 200 1000 400 600 800 1000 Frequency (MHz) Frequency (MHz) Land Pattern +0 5.0 -0.5 3.30.1 1.00.1 5 Tolerance: 0.1 in mm Temperature Profile Reflow Soldering Profile wSoldering profile for Eutectic solder (63Sn/37Pb) (Limit profile: refer to q) T5 T4 T3 T2 Temperature (C) Temperature (C) qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu) T1 t2 Limit Profile t3 Standard Profile t1 T3 T2 Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T2) 220C Time (t2) Standard Profile t1 time (s) time (s) Standard Profile Standard Profile Pre-heating t2 T1 Peak temperature (T3) Cycle of reflow Temp. (T1) Time (t1) Temp. (T2) Time (t2) Peak temperature (T3) Cycle of reflow 2time 150C 60 to 120sec. 183C 30sec. 230 +5/-0C 1time 30 to 60sec. 2453C Pre-heating Heating Limit Profile Pre-heating Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T4) 230C Time (t3) Peak temperature (T5) Cycle of reflow 30 to 50sec. 260 +5/-0C 2time Solder Iron Standard Profile 22 Temperature of soldering iron tip Soldering time Soldering iron power output Cycle of solder iron 35010C 3sec. max. 30W max. 1time PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Storage and Operating Condition) 1. Do not use the trimmer capacitor under atmosphere of RTV silicone rubber (Room Temperature Vulcanizing Silicone Rubber) except Acetone liberating silicone sealant. 2. Before using trimmer capacitor, please store under the condition of -10 to +40 degree C and 30 to 85%RH. 3. Do not store in or near corrosive gasses. 4. Use within 6 months of delivery. 5. Do not store under direct sunlight. 6. Do not use the trimmer capacitor under the conditions listed below. (1) Corrosive gasses atmosphere (ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) Dusty / dirty atmosphere (4) Direct sunlight (5) Static voltage nor electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above Notice (Soldering and Mounting) 1. Soldering (1) TZC3 series can be soldered by reflow soldering method and soldering iron. Do not use flow soldering method (dipping). (2) Soldering condition Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (3) The amount of solder is critical. (4) The thickness of solder paste should be printed from 150 micro m to 200 micro m and the dimension of land pattern should be Murata's standard land pattern used at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals or contact failure due to flux wicking up. (5) When using soldering iron, the diameter of the string solder shall be less than 0.5mm. The string solder shall be applied to the lower part of the terminal only. Do not apply flux except to the terminals. Excessive amounts of solder and/or applying solder to the upper part of the terminal may cause fixed metal rotor or contact failure due to flux invasion into the movable part and/or the contact point. The soldering iron should not come in contact with the stator of the trimmer capacitor. If such contact does occur, the trimmer capacitor may be damaged. (6) Our recommended chlorine content of solder is as follows. (a) Solder paste: 0.2wt% max. (b) String solder: 0.5wt% max. (7) Do not use water-soluble flux (for water cleaning). To prevent the deterioration of trimmer capacitor characteristics, apply flux only to terminals. (8) When soldering the TZC3 series, the solder should not flow into the staking part of the substrate. If such flow does occur, driver slot rotation will be damaged. 2. Mounting (1) Do not apply excessive force (preferably 5.0 N [Ref: 500gf] max.), when the trimmer capacitor is mounted on the PCB. (2) Do not warp and/or bend PCB to prevent trimmer capacitor from breakage. (3) Use the suitable dimension of the pick-up nozzle (2.5mm external diameter and 1.5mm bore diameter). 3. Cleaning Cannot be cleaned because of open construction. 4. Other Note the polarity of the trimmer capacitor to minimize influence by stray capacitance. (Refer to the dimensions concerning the polarity.) Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in driver slot. (1) Recommended screwdriver for manual adjustment Standard type --> MURATA: KMDR010 Cross slot type --> TORAY: SA-1825 (Murata P/N is KMDR040) (2) Recommended screwdriver bit for automatic adjustment Standard type --> MURATA: KMBT010 Cross slot type --> TORAY: JB-1825 (Murata P/N is KMBT040) 2. When adjusting with a screwdriver, do not apply excessive force (preferably 1.0 N [Ref: 100gf] max.) to minimize capacitance drift. If excessive force is applied to the screwdriver slot, it may cause deformation of the products. 3. Do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. They may cause corrosion or electrical contact problems. Notice (Other) Before using trimmer capacitor, please test after assembly in your particular mass production system. 23 5 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors TZW4 Series 5.20.2 2.6 max. 4.20.2 1. To meet high power application due to withstanding voltage 550Vdc. 2. Extremely high self resonant frequency. (More than 3GHz at 1.5pF setting) 3. Typical application: Impedance matching for Cellular Base Station. 4. High Q value in more than VHF, UHF and Microwave bands. (More than 200 in 500MHz, C max.) 5. Available for pick and place machine. Possible thinner design due to 2.6mm low profile. 6. Non electrical contact construction (rotor as middle electrode) provides high reliability. 7. Compact size due to 4.2(W)x5.2(L)x2.6max.(H)mm. 0.6 1.6 0.4 Depth Features 2.80.2 3.0 2.2 +0.1 0.3 -0.2 0.1 ( Tolerance: ) in mm Applications 1. Transmitting power amplifier for Cellular Base Station 2. Transmitting amplifier for PHS Base Station 3. High frequency electric circuit 4. High power radio transmission 5. Transponder amplifier for cable TV Part Number Cmin. (max.) (pF) Cmax. (pF) TC Q Rated Voltage Withstanding Voltage 0.4 1.5 +100/-0% NP0150ppm/C 200min. at 500MHz, Cmax. 250Vdc 550Vdc TZW4Z1R5A001 6 Insulation Resistance: 10000M ohm Torque: 1.5 to 10.0mNm Operating Temperature Range: -55 to +125C Construction Cover Metal Rotor Monolithic Stator 24 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Temperature Characteristics Frequency Characteristics TZW4Z1R5 TZW4Z1R5 Cap.Change (%) Z1R5 (NP0150 ppm/C) +8 1000 +6 +4 +2 Temp. (C) 0 -55 -25 -10 0 Z1R5 -2 20 45 65 85 105 125 1.5pF set 100 -4 -6 -8 Q -10 -12 10 1 500 1000 1500 2000 2500 3000 Frequency (MHz) Land Pattern 7.0 2.5 4.4 Tolerance: 0.1 in mm 6 Temperature Profile Reflow Soldering Profile wSoldering profile for Eutectic solder (63Sn/37Pb) (Limit profile: refer to q) T5 T4 T3 T2 Temperature (C) Temperature (C) qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu) T1 t2 Limit Profile t3 Standard Profile t1 T3 T2 Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T2) 220C Time (t2) Standard Profile t1 time (s) time (s) Standard Profile Standard Profile Pre-heating t2 T1 Peak temperature (T3) Cycle of reflow Temp. (T1) Time (t1) Temp. (T2) Time (t2) Peak temperature (T3) Cycle of reflow 2time 150C 60 to 120sec. 183C 30sec. 230 +5/-0C 1time 30 to 60sec. 2453C Pre-heating Heating Limit Profile Pre-heating Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T4) 230C Time (t3) Peak temperature (T5) Cycle of reflow 30 to 50sec. 260 +5/-0C 2time Solder Iron Standard Profile Temperature of soldering iron tip Soldering time Soldering iron power output Cycle of solder iron 35010C 3sec. max. 30W max. 1time 25 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Storage and Operating Condition) 1. Do not use the trimmer capacitor under atmosphere of RTV silicone rubber (Room Temperature Vulcanizing Silicone Rubber) except Acetone liberating silicone sealant. 2. Before using trimmer capacitor, please store under the condition of -10 to +40 degree C and 30 to 85%RH. 3. Do not store in or near corrosive gasses. 4. Use within 6 months of delivery. 5. Do not store under direct sunlight. 6. Do not use the trimmer capacitor under the conditions listed below. (1) Corrosive gasses atmosphere (Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxie gas, etc.) (2) In liquid (Ex. water, oil, medical liquid, organic solvent, etc.) (3) Dusty/dirty atmosphere (4) Direct sunlight (5) Static voltage nor electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above Notice (Soldering and Mounting) 6 1. Soldering (1) TZW4 series can be soldered by reflow soldering method and soldering iron. Do not use flow soldering method (dipping). (2) Soldering condition Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (3) The amount of solder is critical. (4) The thickness of solder paste should be printed from 150 micro m to 200 micro m and the dimension of land pattern should be Murata's standard land pattern used at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals or contact failure due to flux wicking up. (5) When using soldering iron, the diameter of the string solder shall be less than 0.5mm. The string solder shall be applied to the lower part of the terminal only. Do not apply flux except to the terminals. Excessive amounts of solder and/or applying solder to the upper part of the terminal may cause fixed metal rotor or the contact failure due to flux invasion into the movable part and/or the contact point. The soldering iron should not come in contact with the monolithic stator of the trimmer capacitor. If such contact does occur, the trimmer capacitor may be damaged. (6) Our recommended chlorine content of solder is as follows. (a) Solder paste: 0.2wt% max. (b) String solder: 0.5wt% max. (7) Do not use water-soluble flux (for water cleaning). To prevent the deterioration of trimmer capacitor characteristics, apply flux only to terminals. 2. Mounting (1) Do not apply excessive force (preferably 5.0 N [Ref: 500gf] max.), when the trimmer capacitor is mounted on the PCB. (2) Do not warp and/or bend PCB to prevent trimmer capacitor from breaking. (3) Use the suitable dimension of the pick-up nozzle. (1.8mm external diameter and 1.1mm bore diameter.) 3. Cleaning Cannot be cleaned because of open construction. Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in driver slot. -Recommended screwdriver for manual adjustment VESSEL : No.9000 -1.3x30 (Murata P/N is KMDR130) 2. When adjusting with a screwdriver, do not apply excessive force (preferably 1.0 N [Ref: 100gf] max.) Notice (Other) Before using trimmer capacitor, please test after assembly in your particular mass production system. 26 to minimize capacitance drift. If excessive force applied to the screwdriver slot, it may cause deformation of the products. 3. Do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. They may cause corrosion or electrical contact problems. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors TZB4 Series 0.60.1 Depth 0.5 2.40.1 Features 1. Miniature rectangular shape: 4.0(W)x4.5(L)x3.0(H)mm 2. Color coded case facilitates identification of capacitance range. 3. Designed for automatic placement in surface mount applications. 4. Designed to withstand flux baths and solder baths (with cover film type) 5. Can be temporarily attached to PCB with adhesives (Terminal style A and B) 6. Can be reflow and flow (with cover film type) soldering method 7. Stable characteristics over a wide frequency range (Resonant frequency: 1000MHz min. / 6pF) 4.00.2 1.40.1 dia. 3.00.2 4.50.2 2.70.3 1.20.1 A Type Tolerance: 0.5 in mm 5.0 0.60.1 Depth 0.5 Applications 4.00.2 2.40.1 1.40.1 dia. 1. Car audio systems 2. Cordless telephones 3. Hybrid ICs 4. Pagers 5. Remote keyless entry systems 6. Tuner packs 7. Surveillance cameras 8. DVD 9. Burglarproof devices 3.00.2 4.50.2 1.20.1 B Type Tolerance: 0.5 in mm 7.0 0.60.1 Depth 0.5 4.00.2 2.40.1 1.40.1 dia. 3.00.2 4.50.2 2.5 7 C Type 0.80.1 5.0 6.2 1.40.1 dia. 4.00.2 0.80.1 2.40.1 0.60.1 Depth 0.5 4.00.2 2.40.1 0.60.1 Depth 0.5 Tolerance: 0.5 in mm 4.50.2 4.50.2 2.00.2 3.00.2 2.50.2 1.0 4.00.2 4.5 3.50.2 3.00.2 5.0 7.0 4.8 0.80.1 6.2 D Type E Type Tolerance: 0.5 in mm Tolerance: 0.5 in mm 27 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Part Number Cmin. (max.) (pF) Cmax. (pF) TC TZB4Z030pp10 1.4 3.0 +50/-0% NP0200ppm/C 300min. at 1MHz, Cmax 100Vdc 220Vdc TZB4Z060pp10 2.0 6.0 +50/-0% NP0200ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue TZB4Z100pp10 3.0 10.0 +50/-0% NP0300ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc White TZB4R200pp10 4.5 20.0 +50/-0% N750300ppm/C 500min. at 1MHz, Cmax 100Vdc 220Vdc Red TZB4P300pp10 6.5 30.0 +50/-0% N1200500ppm/C 300min. at 1MHz, Cmax 100Vdc 220Vdc Green TZB4P400pp10 8.5 40.0 +50/-0% N1200500ppm/C 300min. at 1MHz, Cmax 100Vdc 220Vdc Yellow TZB4Z250pp10 4.0 25.0 +100/-0% NP0300ppm/C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Black+Marking TZB4R500pp10 7.0 50.0 +100/-0% N750300ppm/C 300min. at 1MHz, Cmax 50Vdc 110Vdc Black+Marking Q Rated Withstanding Voltage Voltage Stator/Case Color Brown Insulation Resistance: 10000M ohm Torque: 1.5 to 9.8mNm Operating Temperature Range: -25 to +85C First blank: Terminal Type Second blank: Cover film codes (A: not provided, B: provided) ex. TZB4Z100AB10: Terminal Type is A, and Cover film is provided. Construction Land Pattern/Mounting Holes A Type +0 7.0 - 0.5 Cover Film (Cover film type) 2.40.2 Rotor Spring 1.60.1 Plastic Case - Metal Rotor Ceramic Plate Stator Terminal Rotor Terminal + (in mm) B Type C Type +0 8.0 - 0.5 4.00.2 1.60.1 1.10.1 dia. 7 1.10.1 dia. 5.00.5 (in mm) (in mm) D Type E Type 8.0 +0 - 0.5 2.80.2 dia. 1.20.1 1.00.1 4.20.2 0.80.1 5.00.5 (in mm) 3.20.2 dia. (in mm) 28 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Temperature Characteristics TZB4Z060 TZB4Z100 +10 +8 +6 +4 +2 +20 -25 Z100 (NP0300ppm/C) Cap.Change (%) Cap.Change (%) Z060 (NP0200ppm/C) +55 0 -2 0 -25 0 -6 -6 -8 -8 -10 -10 +85 Temp. (C) Cap.Change (%) Cap.Change (%) +55 R500 (N750300ppm/C) +10 +8 +6 +4 0 -2 +4 TZB4R500 R200 (N750400ppm/C) 0 +6 0 -2 -4 TZB4R200 -25 +8 +2 +20 +85 Temp. (C) -4 +2 +20 +10 +55 +10 +8 +6 +4 +2 +20 +85 Temp. (C) -25 0 +55 0 -2 -4 -4 -6 -6 -8 -8 -10 -10 +85 Temp.(C) Frequency Characteristics TZB4Z060 TZB4Z100 Z060 Z100 1000 1000 100 100 1000 1000 100 100 10 10 10 10 1 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Capacitance (pF) Q Capacitance (pF) 7 Q 1 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Continued on the following page. 29 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Frequency Characteristics TZB4R200 TZB4R500 1000 100 Q 100 10 1000 1000 100 100 10 10 Q Capacitance (pF) 1000 10 1 100 200 300 400 500 1 600 100 200 300 400 Capacitance (pF) R500 R200 500 Frequency (MHz) Frequency (MHz) Temperature Profile Flow Soldering Profile Temperature (C) Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu), Eutectic solder (63Sn/37Pb) T3 T2 Standard Profile t2 Limit Profile T1 Pre-heating Standard Profile t1 Heating Temp. (T1) Time (t1) Temp. (T2) Time (t2) Cycle of reflow 150C 60 to 120sec. 250C 5sec. max. 1time time (s) Limit Profile * Immerse the body in solder bath, available for cover film type. * Only immerse the terminal in solder bath-Availabe for terminal shape C and D. Pre-heating Heating Temp. (T1) Time (t1) Temp. (T3) Time (t2) Cycle of reflow 150C 60 to 120sec. 2653C 5sec. max. 2time Reflow Soldering Profile qSoldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu) wSoldering profile for Eutectic solder (63Sn/37Pb) (Limit profile: refer to q) 7 Temperature (C) Temperature (C) T5 T3 T2 T4 T1 t2 Limit Profile t3 Standard Profile T3 T2 t1 time (s) t1 Standard Profile Pre-heating Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. t2 T1 Heating Temp. (T2) 220C Time (t2) Standard Profile time (s) Standard Profile Peak temperature (T3) Cycle of reflow Temp. (T1) Time (t1) Temp. (T2) Time (t2) Peak temperature (T3) Cycle of reflow 2time 150C 60 to 120sec. 183C 30sec. 230 +5/-0C 1time 30 to 60sec. 2453C Pre-heating Heating Limit Profile Pre-heating Temp. (T1) Time (t1) 150 to 180C 60 to 120sec. Heating Temp. (T4) 230C Time (t3) Peak temperature (T5) Cycle of reflow 30 to 50sec. 260 +5/-0C 2time * Available for terminal shape A, B, and E.. Solder Iron Standard Profile 30 Temperature of soldering iron tip Soldering time Soldering iron power output Cycle of solder iron 35010C 3sec. max. 30W max. 1time PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Storage and Operating Condition) 1. Do not use the trimmer capacitor under atmosphere of RTV silicone rubber (Room Temperature Vulcanizing Silicone Rubber) except Acetone liberating silicone sealant. 2. Before using trimmer capacitor, please store under the condition of -10 to +40 degree C and 30 to 85%RH. 3. Do not store in or near corrosive gasses. 4. Use within 6 months of delivery. 5. Do not store under direct sunlight. 6. Do not use the trimmer capacitor under the conditions listed below. (1) Corrosive gasses atmosphere (ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) Dusty / dirty atmosphere (4) Direct sunlight (5) Static voltage nor electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above Notice (Soldering and Mounting) 1. Soldering (1) Can be soldered by reflow soldering method, flow soldering method, and soldering iron. (2) Soldering condition Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (3) The amount of solder is critical. (4) The thickness of solder paste should be printed from 150 micro m to 200 micro m and the dimension of land pattern should be Murata's standard land pattern used at reflow soldering. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals or contact failure due to flux wicking up. (5) When using soldering iron, the string solder shall be applied to the lower part of the terminal only. Do not apply flux except to the terminals. Excessive amounts of solder and/or applying solder to the upper part of the terminal may cause fixed rotor or contact failure due to flux invasion into the movable part and/or the contact point. The soldering iron should not come in contact with the plastic case of the trimmer capacitor. If such contact does occur, the trimmer capacitor may be damaged. (6) Our recommended chlorine content of solder is as follows. (a) Solder paste: 0.2wt% max. (b) String solder: 0.5wt% max. (7) Do not use water-soluble flux (for water cleaning). To prevent the deterioration of trimmer capacitor characteristics, apply flux only to terminals. 2. Mounting (1) Do not apply excessive force (preferably 5.0N [Ref: 500gf] max.), when the trimmer capacitor is mounted on the PCB. (2) Do not warp and/or bend PCB to prevent trimmer capacitor from breakage. (3) Use the suitable PCB holes which are the same pitch as the terminal of the trimmer capacitor. If it would not fit with the terminal, the excessive stress would be applied to the terminal and the trimmer capacitor may deviate from the specified characteristics (Terminal shape C and D). (4) Do not apply bending stress more than 10.0N (Ref: 1kgf) after the trimmer capacitor has been mounted on the PCB (Terminal shape C and D). (5) Mount trimmer capacitor in contact with PCB (Terminal shape C and D). (6) In case of bending the terminals, do not apply excessive force to the body of the product and prevent the terminal fixing part from damaging. (7) Use the suitable dimension of the pick-up nozzle. > Without cover film type - External dimensions of 4.5x4.0mm and 2.5mm bore diameter. > With cover film type - 4.0mm external diameter and 2.0mm bore diameter. 3. Cleaning [with cover film type] Isopropyl-alcohol and Ethyl-alcohol are applicable solvents for cleaning. If you use any other types of solvents, please evaluate performance by your set. Moreover, please confirm no damage for trimmer capacitor after cleaning by your conditions. 4. Other Note the polarity of the trimmer capacitor to minimize influence by stray capacitance. (Refer to the dimensions concerning the polarity.) 7 31 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in driver slot. (1) Recommended screwdriver for manual adjustment MURATA: KMDR010 (2) Recommended screwdriver bit for automatic adjustment MURATA: KMBT010 2. When adjusting with a screwdriver, do not apply excessive force (preferably 1.0 N [Ref: 100gf] max.) to minimize capacitance drift. If excessive force is applied to the screwdriver slot, it may cause deformation of the products. Notice (Other) Before using trimmer capacitor, please test after assembly in your particular mass production system. 7 32 3. Do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. They may cause corrosion or electrical contact problems. 4. Do not break the cover film before the completion of PCB mounting, soldering, and cleaning. 5. Do not clean the trimmer capacitor after the cover film has been broken. 6. To break the cover film, first turn the screwdriver more than 360 deg., and set the capacitance value. (Only inserting the screwdriver cannot break the cover film.) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Ceramic Trimmer Capacitors TZ03 Series 2.50.2 dia. 0.50.2 Depth 0.5 min. Features 4.8 6 3.3 5 1.00.1 F Type 0.2 0.2 .0 0 1.00.1 5 0.0 5 1. Car audio systems 2. Car clocks 3. Stereos 4. Radio cassette tape recorders 5. Cordless telephones 6. Video games 7. Compact radio equipment 8. Remote keyless entry systems 9. Burglarproof devices Tolerance: 0.5 in mm 6.6 2.50.2 dia. 6.0 dia. 0.50.2 Depth 0.5 min. 4.0 Applications 4 6 dia. 1. Color coded case facilitates identification of capacitance range. 2. Sealed construction prevents the penetration of flux and dust. 3. Available in two adjustment styles: Top/Rear. 4. + (Cross-shaped) slot enables automatic adjustment. 6.0 7.8 1.20.1 6.4 3.4 5 0.2 5 0.2 0 . 0 0.0 5 1.00.1 4.8 3.0 3.0 N Type Tolerance: 0.5 in mm Cmin. (max.) (pF) Cmax. (pF) TC Q TZ03Z2R3p169 1.25 2.3 +50/-0% NP0200ppm/C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Black TZ03Z050p169 1.5 5.0 +50/-0% NP0200ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue TZ03Z070p169 2.0 7.0 +50/-0% NP0200ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue TZ03N100p169 2.1 10.0 +50/-0% N200200ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc White TZ03Z100p169 2.7 10.0 +50/-0% NP0200ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Blue TZ03T110p169 3.0 11.0 +50/-0% N450300ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc White TZ03R200p169 4.2 20.0 +50/-0% N750300ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Red TZ03T200p169 4.2 20.0 +50/-0% N450300ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Pink TZ03R300p169 5.2 30.0 +50/-0% N750300ppm/C 500min. at 1MHz, Cmax. 100Vdc 220Vdc Green TZ03P450p169 6.8 45.0 +50/-0% N1200500ppm/C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Yellow TZ03P600p169 9.8 60.0 +50/-0% N1200500ppm/C 300min. at 1MHz, Cmax. 100Vdc 220Vdc Brown TZ03Z500p169 6.0 50.0 +100/-0% NP0300ppm/C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Orange TZ03R900p169 9.0 90.0 +100/-0% N750300ppm/C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Black+Dot TZ03R121p169 10.0 120.0 +100/-0% N750300ppm/C 300min. at 1MHz, Cmax. 50Vdc 110Vdc Black Part Number Insulation Resistance: 10000M ohm Torque: 2.0 to 14.7mNm A blank column is filled with terminal type codes. Rated Withstanding Voltage Voltage Stator/Case Color 8 Operating Temperature Range: -25 to +85C 33 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Construction Mounting Holes F Type N Type 3 dia. a. 0. 1 1.30.1 1. 3 1. 3 0. 1 di di a . 10.1 3 3.3 5 Tolerance: 0.5 in mm Tolerance: 0.5 in mm Temperature Characteristics TZ03Z070 TZ03T110 Z070 (NP0200ppm/C) +6 +4 +2 55 +2 85 20 55 20 0 0 -25 Cap.Change (%) +4 Cap.Change (%) T110 (N450300ppm/C) +6 -25 -2 0 0 Temp. (C) Temp. (C) 85 -2 -4 -4 -6 -6 8 TZ03R200 TZ03P600 +4 +2 Cap.Change (%) +6 +8 +6 +4 Cap.Change (%) P600 (N1200500ppm/C) R200 (N750300ppm/C) +2 20 -25 0 0 55 85 Temp. (C) 20 -25 0 0 55 85 Temp. (C) -2 -2 -4 -4 -6 -6 -8 -10 Continued on the following page. 34 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Temperature Characteristics TZ03Z500 TZ03R121 Z500 (NP0300ppm/C) +4 +2 +8 +6 +4 55 85 +2 20 -25 0 20 0 -2 Cap.Change (%) +6 R121 (N750300ppm/C) Cap.Change (%) +8 -25 Temp. (C) 0 55 0 -2 -4 -4 -6 -6 -8 -8 -10 -10 85 Temp. (C) Frequency Characteristics TZ03Z070 TZ03T110 1000 100 100 Q 10 Capacitance (pF) 1000 1000 100 100 10 10 Q 10 100 200 300 400 500 600 700 800 900 1000 1 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Frequency (MHz) TZ03R200 TZ03P450 R200 1000 1000 100 100 Q 10 10 1 100 200 300 Frequency (MHz) 400 500 Capacitance (pF) P450 1000 1000 100 100 10 10 Q 1 100 200 300 400 Capacitance (pF) 1 1000 Capacitance (pF) T110 Z070 8 500 Frequency (MHz) Continued on the following page. 35 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Continued from the preceding page. Frequency Characteristics TZ03P600 TZ03R900 P600 1000 100 100 Q 1000 1000 100 100 10 10 Q 10 10 1 100 200 300 400 500 1 200 100 300 400 Capacitance (pF) 1000 Capacitance (pF) R900 500 Frequency (MHz) Frequency (MHz) Temperature Profile Flow Soldering Profile Temperature (C) Soldering profile for Lead-free solder (96.5Sn/3Ag/0.5Cu), Eutectic solder (63Sn/37Pb) T3 T2 Standard Profile t2 Heating T1 Limit Profile Standard Profile t1 Pre-heating Heating Temp. (T1) Time (t1) Temp. (T2) Time (t2) Cycle of reflow 150C 60 to 120sec. 250C 5sec. max. 1time time (s) Pre-heating Limit Profile Pre-heating Heating Temp. (T1) Time (t1) Temp. (T3) Time (t2) Cycle of reflow 150C 60 to 120sec. 2653C 5sec. max. 2time Solder Iron Standard Profile 8 36 Temperature of soldering iron tip Soldering time Soldering iron power output Cycle of solder iron 35010C 3sec. max. 30W max. 1time PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Storage and Operating Condition) 1. Do not use the trimmer capacitor under atmosphere of RTV silicone rubber (Room Temperature Vulcanizing Silicone Rubber) except Acetone liberating silicone sealant. 2. Before using trimmer capacitor, please store under the condition of -10 to +40 degree C and 30 to 85%RH. 3. Do not store in or near corrosive gasses. 4. Use within 6 months of delivery. 5. Open the package just before using. 6. Prior to storing previously opened packages, the packaging should be heat-sealed. Avoid using rubber bands for repackaging. 7. Do not store under direct sunlight. 8. Do not use the trimmer capacitor under the conditions listed below. (1) Corrosive gasses atmosphere (ex. Chlorine gas, Hydrogen sulfide gas, Ammonia gas, Sulfuric acid gas, Nitric oxide gas, etc.) (2) In liquid (ex. water, oil, medical liquid, organic solvent, etc.) (3) Dusty / dirty atmosphere (4) Direct sunlight (5) Static voltage nor electric/magnetic fields (6) Direct sea breeze (7) Other variations of the above Notice (Soldering and Mounting) 1. Soldering (1) TZ03 series can be soldered by flow soldering method and soldering iron. Do not use reflow soldering method. (2) Soldering condition Refer to the temperature profile. If the soldering conditions are not suitable, e.g., excessive time and/or excessive temperature, the trimmer capacitor may deviate from the specified characteristics. (3) The dimension of mounting hole should be Murata's standard mounting hole used at flow soldering. The amount of solder is critical. Insufficient amounts of solder can lead to insufficient soldering strength on PCB. Excessive amounts of solder may cause bridging between the terminals or contact failure due to flux wicking up. (4) When using soldering iron, the string solder shall be applied to the lower part of the terminal only. Do not apply flux except to the terminals. Excessive amounts of solder and/or applying solder to the upper part of the terminal may cause fixed rotor or the contact failure due to flux invasion into the movable part and/or the contact point. The soldering iron should not come in contact with the plastic case of the trimmer capacitor. If such contact does occur, the trimmer capacitor may be damaged. (5) Our recommended chlorine content of string solder is 0.5wt% max. (6) Do not use water-soluble flux (for water cleaning). To prevent the deterioration of trimmer capacitor characteristics, apply flux only to terminals. 2. Mounting (1) Do not apply excessive force (preferably 5.0 N [Ref: 500gf] max.), when the trimmer capacitor is mounted on the PCB. (2) Use the suitable PCB holes which are the same pitch as the terminal of the trimmer capacitor. If it would not fit with the terminal, the excessive stress would be applied to the terminal and the trimmer capacitor may deviate from the specified characteristics. (3) Do not apply bending stress more than 10.0N (Ref: 1kgf) after the trimmer capacitor has been mounted on the PCB. (4) Mount trimmer capacitor in contact with PCB. (5) In case of bending the terminals, do not apply excessive force to the body of the product and prevent the terminal fixing part from damaging. 3. Cleaning Isopropyl-alcohol and Ethyl-alcohol are applicable solvents for cleaning. If you use any other types of solvents, please evaluate performance by your set. Moreover, please confirm no damage for trimmer capacitor after cleaning by your conditions. 4. Other Note the polarity of the trimmer capacitor to minimize influence by stray capacitance. (Refer to the dimensions concerning the polarity.) 8 37 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Notice (Handling) 1. Use suitable screwdrivers that fit comfortably in driver slot. (1) Recommended screwdriver for manual adjustment MURATA: KMDR010 (2) Recommended screwdriver bit for automatic adjustment MURATA: KMBT010 Notice (Other) Before using trimmer capacitor, please test after assembly in your particular mass production system. 8 38 2. When adjusting with a screwdriver, do not apply excessive force (preferably 1.0 N [Ref: 100gf] max.) to minimize capacitance drift. If excessive force is applied to the screwdriver slot, it may cause deformation of the products. 3. Do not apply adhesive, lock paints, or any other substances to the trimmer capacitor to secure the rotor position. They may cause corrosion or electrical contact problems. PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Packaging Minimum Quantity Minimum Quantity (pcs.) Part Number 180mm Reel 330mm Reel Bulk TZR1 3000 10000 500 TZS2 3000 10000 500 TZY2 2000 10000 500 TZV2 2000 8000 500 TZC3 1000 4000 500 TZW4 500 - 100 TZB4 500 2500 500 TZ03 - - 1000 Dimension of Tape TZR1 Series TZS2 Series 2.00.1 4.00.1 3.50.1 3.00.2 1.80.2 1.250.2 +0.1 1.5 -0 dia. 0.250.1 8.00.3 1.750.1 2.00.2 3.50.1 1.5 +0.1 -0 Dia. 4.00.1 0.250.1 8.00.3 1.050.2 4.00.1 1.750.1 2.00.1 4.00.1 2.50.2 (in mm) (in mm) TZY2/TZV2 Series 1.5 +0.1 - 0 dia. t 4.0 2 4 0.3 5.5 4.90.2 8.00.2 3.5 A 3.60.2 2.00.2 120.3 A 0.25 1.75 2.0 TZC3 Series 1.75 1.5 +0.1 - 0 dia. A-Across section A A A-Across section 3.60.2 8 2.70.2 t=TZY2 (TZVY2) : 1.60.2 TZV2 (TZV02) : 1.90.2 4.0 Tolerance : 0.1 in mm Tolerance: 0.1 in mm 8 TZW4 Series TZB4 Series A 8 4.6 4 .0 A 5.5 1.75 2.0 120.2 5.6 5.5 A 8.0 0.3 4.8 7.5 4 1.75 2 +0.1 1.5 - 0 dia. 2.6 A-Across section 3.550.2 0.30.1 12.00.3 1.5 +0.1 - 0 dia. 1.8 A-Across section A 4.3 Tolerance: 0.1 in mm Direction of feed Tolerance: 0.1 in mm Continued on the following page. 39 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Packaging Continued from the preceding page. Dimension of dia. 178mm Reel TZR1/TZS2/TZY2/TZV2 Series TZC3/TZW4/TZB4 Series 2.00.5 21.00.8 dia. 50 min. 13.00.5 dia. 50 min. 13.00.5 dia. 2.00.5 21.00.8 dia. 9.01.0 13.01.0 13.01.0 17.01.0 1782 dia. 1782 dia. (in mm) (in mm) Dimension of dia. 330mm Reel TZR1/TZS2/TZY2/TZV2 Series TZC3/TZB4 Series 2.00.5 21.00.8 dia. 50 min. 13.00.5 dia. 50 min. 13.00.5 dia. 2.00.5 21.00.8 dia. 9.51.0 13.51.0 13.51.0 3282 dia. 3282 dia. (in mm) 8 40 17.51.0 (in mm) PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Recommended Adjustment Tools Please use the following recommended screwdriver. You can order this driver with part number below. Though you can also adjust the capacitance value by commercial products, please use one which has the same head size as the driver below. For Manual Adjusutment Series MURATA Model Number Manufacturers Model Number Shape 80 1.5 TZR1 KMDR160 MURATA MFG. KMDR160 Bit shape: Minus (0.3x0.13) (in mm) 80 1.5 TZS2 KMDR050 MURATA MFG. KMDR050 Bit shape: Square (0.54x0.54) (in mm) 108 18 TZY2 KMDR060 ENGINEER INC. DA-89 Bit shape: Minus (0.8x0.35) (in mm) 125 15 TZV2 KMDR020 VESSEL MFG. 9000 0.9-30 NO.9000 -0.9g30 Bit shape: Minus (0.9x0.4) (in mm) 120 13 TZC3 Cross Slot Type KMDR040 TORAY INDUSTRIES, INC. SA-1825 Bit shape: Minus (1.8x0.45) (in mm) 122 50 20 TZC3 Standard Type (Minus Slot) KMDR010 MURATA MFG. KMDR010 Bit shape: 8 Minus (2.2x0.4) (in mm) 125 15 TZW4 KMDR130 VESSEL MFG. 9000 CERAMIC BLADE ELECTRONICS NO.9000 -1.3g30 Bit shape: 1.3-30 Minus (1.3x30) (in mm) 122 50 20 TZB4 TZ03 KMDR010 MURATA MFG. KMDR010 Bit shape: Minus (2.2x0.4) (in mm) Continued on the following page. 41 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Recommended Adjustment Tools Continued from the preceding page. For Automatic Adjustment Series MURATA Model Number Manufacturers Model Number Shape 20 2 KMBT050 MURATA MFG. KMBT050 1.8 dia. TZS2 Bit shape: Square (0.54x0.54) (in mm) 25 0.6 KMBT060 MURATA MFG. KMBT060 Bit shape: Minus (0.56 x0.25) 2.4 dia. TZY2 (in mm) 25 0.6 KMBT020 MURATA MFG. 2.4 dia. TZV2 KMBT020 Bit shape: Minus (0.9x0.4) (in mm) 25 5 KMBT040 JB-1825 Bit shape: Minus (1.8x0.45) 1.8 dia. TZC3 Cross Slot Type TORAY INDUSTRIES, INC. (in mm) TZC3 Standard Type (Minus Slot) TZB4 TZ03 KMBT010 MURATA MFG. KMBT010 Bit shape: Minus (2.2x0.4) 2.2 dia. 30 (in mm) 8 42 PDF catalog is downloaded from!CAUTION the website (for of Murata Manufacturing co., ltd. Therefore, it's specifications areinsubject to change or oursmoking productsand/or in it may be discontinued without advance notice. Please check with our * Please read rating and storage, operating, rating, soldering, mounting and handling) this catalog to prevent burning, etc. !Note * This !Note T13E.pdf 07.3.1 sales representatives or product engineers before ordering. * This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Qualified Standards The products listed herein have been produced by the QS9000 and ISO9001 certified factory MURATA FACTORY Sabae Murata Mfg. Co., Ltd. No ODCs (Ozone Depleting Chemicals) are used on any Murata trimmer potentiometers. TRIMCAPr is a registered trademark of Murata Mfg. Co., Ltd. 43 !Note * This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. * This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. T13E.pdf 07.3.1 Note: 1. Export Control For customers outside Japan No muRata products should be used or sold, through any channels, for use in the design, development, production, utilization, maintenance or operation of, or otherwise contribution to (1) any weapons (Weapons of Mass Destruction (nuclear, chemical or biological weapons or missiles) or conventional weapons) or (2) goods or systems specially designed or intended for military end-use or utilization by military end-users. For customers in Japan For products which are controlled items subject to the "Foreign Exchange and Foreign Trade Law" of Japan, the export license specified by the law is required for export. < < > > 2. Please contact our sales representatives or product engineers before using the products in this catalog for the applications listed below, which require especially high reliability for the prevention of defects which might directly damage a third party's life, body or property, or when one of our products is intended for use in applications other than those specified in this catalog. q Aircraft equipment w Aerospace equipment e Undersea equipment r Power plant equipment t Medical equipment y Transportation equipment (vehicles, trains, ships, etc.) u Traffic signal equipment i Disaster prevention / crime prevention equipment o Data-processing equipment !0 Application of similar complexity and/or reliability requirements to the applications listed above 3. Product specifications in this catalog are as of March 2007. They are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. If there are any questions, please contact our sales representatives or product engineers. 4. Please read rating and CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. 5. This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 6. Please note that unless otherwise specified, we shall assume no responsibility whatsoever for any conflict or dispute that may occur in connection with the effect of our and/or a third party's intellectual property rights and other related rights in consideration of your use of our products and/or information described or contained in our catalogs. In this connection, no representation shall be made to the effect that any third parties are authorized to use the rights mentioned above under licenses without our consent. 7. No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process. http://www.murata.com/ Head Office 1-10-1, Higashi Kotari, Nagaokakyo-shi, Kyoto 617-8555, Japan Phone: 81-75-951-9111 International Division 3-29-12, Shibuya, Shibuya-ku, Tokyo 150-0002, Japan Phone: 81-3-5469-6123 Fax: 81-3-5469-6155 E-mail: intl@murata.co.jp Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Murata: KMDR160 KMDR090 KMDR040 KMDR060 KMDR020 KMBT060 KMDR190