a 10-Bit Digital Temperature Sensor in 6-Lead SOT-23 AD7814 FEATURES 10-Bit Temperature-to-Digital Converter -55C to +125C Operating Temperature Range 2C Accuracy SPI- and DSP-Compatible Serial Interface Shutdown Mode Space-Saving SOT-23 Package APPLICATIONS Hard Disk Drives Personal Computers Electronic Test Equipment Office Equipment Domestic Appliances Process Control FUNCTIONAL BLOCK DIAGRAM BAND GAP TEMPERATURE SENSOR 10-BIT ANALOG/DIGITAL CONVERTER GND VDD TEMPERATURE VALUE REGISTER AD7814 SERIAL BUS INTERFACE CS SCLK DIN DOUT GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The AD7814 is a complete temperature monitoring system in a SOT-23 package or 8-lead MSOP package. It contains a band gap temperature sensor and 10-bit ADC to monitor and digitize the temperature reading to a resolution of 0.25C. 1. The AD7814 has an on-chip temperature sensor that allows an accurate measurement of the ambient temperature. The measurable temperature range is -55C to +125C, with a 2C temperature accuracy. The AD7814 has a flexible serial interface that allows easy interfacing to most microcontrollers. The interface is compatible with SPI(R), QSPITM, and MICROWIRETM protocol, and is also compatible with DSPs. The part features a standby mode that is controlled via the serial interface. 2. Supply voltage of 2.7 V to 5.5 V The AD7814's wide supply voltage range, low supply current, and SPI-compatible interface make it ideal for a variety of applications, including personal computers, office equipment, and domestic appliances. 3. Space-saving 6-lead SOT-23 package and 8-lead MSOP package 4. 10-bit temperature reading to 0.25C resolution 5. Standby mode that reduces the current consumption to 1 A Purchase of licensed I 2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I 2C Patent Rights to use these components in an I 2C system, provided that the system conforms to the I 2C Standard Specification as defined by Philips. REV. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) 2004 Analog Devices, Inc. All rights reserved. AD7814-SPECIFICATIONS1 (T = T A Parameter Min Typ TEMPERATURE SENSOR AND ADC Accuracy 2.0 10 400 25 Resolution Update Rate, tR Temperature Conversion Time SUPPLIES Supply Voltage Supply Current Normal Mode Shutdown Mode (VDD = 5 V) Shutdown Mode (VDD = 3 V) Power Dissipation Power Dissipation 1 sps 10 sps 100 sps 2.7 250 1.23 0.43 80 MIN to TMAX, VDD = 2.7 V to 5.5 V, unless otherwise noted.) Max Unit Test Conditions/Comments 2.0 2.5 3.5 C C C Bits s s TA = 0C to 85C. VDD = 3 V to 5.5 V2 TA = -40C to 0C. VDD = 3 V to 5.5 V2 TA = -55C to +125C. VDD = 3 V to 5.5 V 5.5 V For Specified Performance 400 3 1 A A A W W W W 3.7 3.9 5.8 DIGITAL INPUT3 Input High Voltage, VIH Input Low Voltage, VIL Input Current, IIN Input Capacitance, CIN 2.4 DIGITAL OUTPUT3 Output High Voltage, VOH Output Low Voltage, VOL Output Capacitance, COUT 0.8 1 10 V V A pF 0.4 50 V pF VDD - 0.3 V VDD = 3 V. Using Normal Mode VDD = 3 V. Using Shutdown Mode VIN = 0 V to VDD All Digital Inputs ISOURCE = ISINK = 200 A IOL = 200 A NOTES 1 All specifications apply for -55C to +125C unless otherwise stated. 2 For VDD = 2.7 V to 3 V and T A = -40C to +85C, the typical temperature error is 2C. 3 Guaranteed by design and characterization, not production tested. Specifications subject to change without notice. TIMING CHARACTERISTICS1, 2, 3 (T = T A MIN to TMAX, VDD = 2.7 V to 5.5 V, unless otherwise noted.) Parameter Limit Unit Comments t1 t2 t3 t4 4 t5 t6 t7 t8 4 0 50 50 35 20 0 0 40 ns min ns min ns min ns max ns min ns min ns min ns max CS to SCLK Setup Time SCLK High Pulse Width SCLK Low Pulse Width Data Access Time After SCLK Falling Edge Data Setup Time Prior to SCLK Rising Edge Data Hold Time After SCLK Rising Edge CS to SCLK Hold Time CS to DOUT High Impedance NOTES 1 Guaranteed by design and characterization, not production tested. 2 All input signals are specified with tr = tf = 5 ns (10% to 90% of V DD) and timed from a voltage level of 1.6 V. 3 See Figure 2. 4 Measured with the load circuit of Figure 1. Specifications subject to change without notice. -2- REV. E AD7814 ABSOLUTE MAXIMUM RATINGS* VDD to GND . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to +7 V Digital Input Voltage to GND . . . . . . . -0.3 V to VDD + 0.3 V Digital Output Voltage to GND . . . . . -0.3 V to VDD + 0.3 V Operating Temperature Range . . . . . . . . . . -55C to +125C Storage Temperature Range . . . . . . . . . . . . -65C to +150C Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 150C SOT-23, Power Dissipation . . . . . . . . . . . . . . . . . . . . 450 mW JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 240C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . 215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . 220C MSOP Package, Power Dissipation . . . . . . . . . . . . . . 450 mW JA Thermal Impedance . . . . . . . . . . . . . . . . . . . . 206C/W Lead Temperature, Soldering Vapor Phase (60 sec) . . . . . . . . . . . . . . . . . . . . . . 215C Infrared (15 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . 220C 200A TO OUTPUT PIN IOL 1.6V CL 50pF 200A IOH Figure 1. Load Circuit for Data Access Time and Bus Relinquish Time *Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ORDERING GUIDE Model Temperature Range Temperature Error1 Package Description Package Option Branding Information AD7814ART-500RL7 AD7814ART-REEL AD7814ART-REEL7 AD7814ARTZ-500RL72 AD7814ARTZ-REEL2 AD7814ARTZ-REEL72 AD7814ARM AD7814ARM-REEL AD7814ARM-REEL7 AD7814ARMZ2 AD7814ARMZ-REEL2 AD7814ARMZ-REEL72 -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C -55C to +125C 2C 2C 2C 2C 2C 2C 2C 2C 2C 2C 2C 2C 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 6-Lead SOT-23 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP 8-Lead MSOP RT-6 RT-6 RT-6 RT-6 RT-6 RT-6 RM-8 RM-8 RM-8 RM-8 RM-8 RM-8 CAA CAA CAA CAA CAA CAA CAA CAA CAA CAA CAA CAA 1 2 Temperature error is over 0C to 85C temperature range. Z = Pb-free part CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD7814 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. REV. E -3- WARNING! ESD SENSITIVE DEVICE AD7814 PIN FUNCTION DESCRIPTIONS Pin Mnemonic SOT-23 Pin No. MSOP Pin No. GND DIN 1 2 7 6 VDD SCLK 3 4 5 4 CS 5 3 DOUT 6 2 NC Description Analog and Digital Ground Serial Data Input. Serial data to be loaded to the part's control register is provided on this input. Data is clocked into the control register on the rising edge of SCLK. Positive Supply Voltage, 2.7 V to 5.5 V Serial Clock Input. This is the clock input for the serial port. The serial clock is used to clock data out of the temperature value register of the AD7814 and to clock data into the control register on the part. Chip Select Input. Logic input. The device is selected when this input is low. The SCLK input is disabled when this pin is high. Serial Data Output. Logic output. Data is clocked out of the temperature value register at this pin. Data is clocked out on the falling edge of SCLK. No Connect 1, 8 PIN CONFIGURATIONS SOT-23 GND 1 MSOP 6 AD7814 DIN 2 VDD 3 TOP VIEW (Not to Scale) DOUT 5 CS 4 SCLK NC 1 8 AD7814 NC GND TOP VIEW CS 3 (Not to Scale) 6 DIN DOUT 2 SCLK 4 7 5 VDD NC = NO CONNECT -4- REV. E AD7814 25 s later. Reading from the device before conversion is complete will provide the same set of data. CIRCUIT INFORMATION The AD7814 is a 10-bit digital temperature sensor. The part houses an on-chip temperature sensor, a 10-bit A/D converter, a reference, and serial interface logic functions in a SOT-23 package. The A/D converter section consists of a conventional successive-approximation converter based around a capacitor DAC. The parts are capable of running on a 2.7 V to 5.5 V power supply. TEMPERATURE VALUE REGISTER The temperature value register is a read-only register that stores the temperature reading from the ADC in 10-bit twos complement format. The temperature data format is shown in Table I. This shows the full theoretical range of the ADC from -128C to +127C, but in practice the temperature measurement range is limited to the operating temperature range of the device (-55C to +125C). A typical performance curve is shown in Figure 7. The on-chip temperature sensor allows an accurate measurement of the ambient device temperature to be made. The working measurement range of the AD7814 is -55C to +125C. Table I. Temperature Data Format CONVERTER DETAILS The conversion clock for the part is internally generated so no external clock is required except when reading from and writing to the serial port. In normal mode, an internal clock oscillator runs the automatic conversion sequence. A conversion is initiated approximately every 350 s. At this time, the part wakes up and performs a temperature conversion. This temperature conversion typically takes 25 s, at which time the part automatically shuts down. The result of the most recent temperature conversion is available in the serial output register at any time. Once the conversion is finished, an internal oscillator starts counting and is designed to time out every 350 s. The AD7814 then powers up and does a conversion. Please note that if the CS is brought low every 350 s ( 30%), then the same temperature value will be output onto the DOUT line every time without changing. It is recommended that the CS line is not brought low every 350 s ( 30%). The 30% covers process variation. The CS should become active (high to low) outside this range. The device is designed to autoconvert every 350 s. If the AD7814 is accessed during the conversion process, an internal signal is generated to prevent any update of the temperature value register during the conversion. Otherwise the user could read back spurious data. The design of this feature results in this internal lockout signal being reset only at the start of the next autoconversion. Therefore, if the CS line goes active before the internal lockout signal has been reset to its inactive mode, the internal lockout signal will not be reset. To ensure that no lockout signal is set, bring the CS low at a greater or less time than 350 s ( 30%). This will mean that the AD7814 is not interrupted during a conversion process. The AD7814 can be placed in a shutdown mode, via the control register, in which case the on-chip oscillator is shut down and no further conversions are initiated until the AD7814 is taken out of shutdown mode. The conversion result from the last conversion prior to shutdown can still be read from the AD7814 even when it is in shutdown mode. In the automatic conversion mode, every time a read or write operation takes place, the internal clock oscillator is restarted at the end of the read or write operation. The result of the conversion is typically available 25 s later. Similarly, when the part is taken out of shutdown mode, the internal clock oscillator is restarted and the conversion result is typically available REV. E Temperature Digital Output DB9 . . . DB0 -128C -125C -100C -75C -50C -25C -0.25C 0C +0.25C +10C +25C +50C +75C +100C +125C +127C 10 0000 0000 10 0000 1100 10 0111 0000 10 1101 0100 11 0011 1000 11 1001 1100 11 1111 1111 00 0000 0000 00 0000 0001 00 0010 1000 00 0110 0100 00 1100 1000 01 0010 1100 01 1001 0000 01 1111 0100 01 1111 1100 SERIAL INTERFACE The serial interface on the AD7814 consists of four wires CS, SCLK, DIN, and DOUT. The interface can be operated in 3-wire mode with DIN tied to Ground, in which case the interface has read-only capability, with data being read from the data register via the DOUT line. The DIN line is used to write the part into standby mode, if required. The CS line is used to select the device when more than one device is connected to the serial clock and data lines. The part operates in a slave mode and requires an externally applied serial clock to the SCLK input to access data from the data register. The serial interface on the AD7814 is designed to allow the part to be interfaced to systems that provide a serial clock that is synchronized to the serial data, such as the 80C51, 87C51, 68HC11, 68HC05, and PIC16Cxx microcontrollers, as well as DSP processors. A read operation from the AD7814 accesses data from the temperature value register, while a write operation to the part writes data to the control register. -5- AD7814 CS t1 SCLK t7 t2 1 2 3 LEADING ZERO DB9 t5 DIN DON'T CARE 11 15 t3 t4 DOUT 4 DON'T CARE 16 t8 DB8 DB0 t6 POWERDOWN Figure 2. Serial Interface Timing Diagram Read Operation AD7814 to MC68HC11 Interface Figure 2 shows the timing diagram for a serial read from the AD7814. The CS line enables the SCLK input. Ten bits of data and a leading zero are transferred during a read operation. Read operations occur during streams of 16 clock pulses. The serial data is accessed in a number of bytes if 10 bits of data are being read. At the end of the read operation, the DOUT line remains in the state of the last bit of data clocked out of the AD7814 until CS returns high, at which time the DOUT line goes into three-state. Figure 3 shows an interface between the AD7814 and the MC68HC11 microcontroller. The MC68HC11 is configured in the master mode with its CPOL bit set to a logic one and its CPHA bit set to a logic one. When the MC68HC11 is configured like this, its SCLK line idles high between data transfers. Data is transferred to and from the AD7814 in two 8-bit serial data operations. The diagram shows the full (4-wire) interface. PC1 of the MC68HC11 is configured as an output and used to drive the CS input. Write Operation Figure 2 also shows the timing diagram for a serial write to the AD7814. The write operation takes place at the same time as the read operation. Data is clocked into the control register on the part on the rising edge of SCLK. Only the third bit in the data stream provides a user-controlled function. This third bit is the power-down bit which, when set to a 1, puts the AD7814 into shutdown mode. The first 2 bits of the data stream are "don't cares" while all other bits in the data stream, other than the power-down bit, should be 0 to ensure correct operation of the AD7814. Data is loaded to the control register on the fifteenth falling SCLK edge and the data takes effect at this time (i.e., if the part is programmed to go into shutdown, it does so at this point). If the CS is brought high before this fifteenth SCLK edge, the control register will not be loaded and the power-down status of the part will not change. AD7814* MC68HC11* SCLK SCLK DOUT MISO DIN MOSI CS PC1 *ADDITIONAL PINS OMITTED FOR CLARITY Figure 3. AD7814 to MC68HC11 Interface AD7814 to 8051 Interface An interface circuit between the AD7814 and the 8051 microcontroller is shown in Figure 4. The 8xC51 is configured in its Mode 0 serial interface mode. The serial clock line of the 8xC51 (on P3.1) idles high between data transfers. Data is transferred to and from the AD7814 in two 8-bit serial data operations. The AD7814 outputs the MSB of its data stream as the first valid bit while the 8xC51 expects the LSB first. Thus, the data read into the serial buffer needs to be rearranged before the correct data word from the AD7814 is available in the accumulator. MICROPROCESSOR INTERFACING The AD7814's serial interface allows for easy interface to most microcomputers and microprocessors. Figures 3 through 6 show some typical interface circuits. In the example shown, the AD7814 is connected to the serial port of the 8051. Because the serial interface of the 8xC51 contains only one data line, the DIN line of the AD7814 is tied low in the interface example given in Figure 4. The serial interface on the AD7814 consists of four wires: CS, DIN, DOUT, and SCLK. All interface circuits shown utilize all four interface lines. However, it is possible to operate the interface with three wires. If the application does not require the power-down facility offered by the AD7814, the DIN line can be tied permanently low. Thus, the interface can be operated from just three wires: SCLK, CS, and DOUT. For applications that require the use of the power-down feature of the AD7814, the serial interface should be implemented using data port lines on the 8051. This allows a full-duplex serial interface to be implemented. The method involves `bitbanging' a port line to generate a serial clock while using two other port lines to shift data in and out with the fourth port line connecting to CS. Port lines 1.0 through 1.3 (with P1.1 configured as an input) can be used to connect to SCLK, DOUT, DIN, and CS, respectively, to implement this scheme. The serial data transfer to and from the AD7814 requires a 16-bit read operation. Many 8-bit microcontrollers have 8-bit serial ports and this 16-bit data transfer is handled as two 8-bit transfers. Other microcontrollers and DSP processors transfer 16 bits of data in a serial data operation. -6- REV. E AD7814 8051* AD7814* ADSP-21xx* AD7814* SCLK P3.1 SCLK SCK DOUT P3.0 DOUT DR DIN P1.2 DIN DT CS P1.3 CS RFS TFS *ADDITIONAL PINS OMITTED FOR CLARITY *ADDITIONAL PINS OMITTED FOR CLARITY Figure 4. AD7814 to 8051 Interface Figure 6. AD7814 to ADSP-21xx Interface AD7814 to PIC16C6x/7x Interface Figure 5 shows an interface circuit between the AD7814 and the PIC16C6x/7x microcontroller. The PIC16C6x/7x synchronous serial port (SSP) is configured as an SPI master with the clock polarity bit set to a logic one. In this mode, the serial clock line of the PIC16C6x/7x idles high between data transfers. Data is transferred to and from the AD7814 in two 8-bit serial data operations. In the example shown, port line RA1 is being used to generate the CS for the AD7814. AD7814* PIC16C6x/7x* SCLK SCK DOUT SDO DIN SDI CS RA1 MOUNTING THE AD7814 The AD7814 can be used for surface or air temperature sensing applications. If the device is cemented to a surface with thermally conductive adhesive, the die temperature will be within about 0.1C of the surface temperature, thanks to the device's low power consumption. Care should be taken to insulate the back and leads of the device from the air, if the ambient air temperature is different from the surface temperature being measured. The ground pin provides the best thermal path to the die, so the temperature of the die will be close to that of the printed circuit ground track. Care should be taken to ensure that this is in good thermal contact with the surface being measured. As with any IC, the AD7814 and its associated wiring and circuits must be kept free from moisture to prevent leakage and corrosion, particularly in cold conditions where condensation is more likely to occur. Water-resistant varnishes and conformal coatings can be used for protection. The small size of the AD7814 package allows it to be mounted inside sealed metal probes, which provide a safe environment for the device. *ADDITIONAL PINS OMITTED FOR CLARITY Figure 5. AD7814 to PIC16C6x/7x Interface AD7814 to ADSP-21xx Interface Figure 6 shows an interface between the AD7814 and the ADSP-21xx DSP processor. To ensure correct operation of the interface, the SPORT control register should be set up as follows: SUPPLY DECOUPLING TFSW = RFSW = 1, Alternate Framing INVRFS = INVTFS = 1, Active Low Framing Signal DTYPE = 00, Right Justify Data SLEN = 1111, 16-Bit Data Words ISCLK = 1, Internal Serial Clock TFSR = RFS = 1, Frame Every Word IRFS = 0, RFS Configured As Input ITFS = 1, TFS Configured As Output The AD7814 should be decoupled with a 0.1 F ceramic capacitor between VDD and GND. This is particularly important if the AD7814 is mounted remotely from the power supply. 1.0 TEMPERATURE ERROR 0.8 The interface requires an inverter between the SCLK line of the ADSP-21xx and the SCLK input of the AD7814. The ADSP21xx has the TFS and RFS of the SPORT tied together with TFS set as an output and RFS set as an input. The DSP operates in alternate framing mode and the SPORT control register is set up as described earlier. 0.6 0.4 0.2 0 -0.2 -0.4 -55 -40 0 25 40 TEMPERATURE - C 85 100 Figure 7. Typical Temperature Error REV. E -7- 120 AD7814 OUTLINE DIMENSIONS C01041-0-8/04(E) 6-Lead Small Outline Transistor Package [SOT-23] (RT-6) Dimensions shown in millimeters 2.90 BSC 6 5 4 1 2 3 2.80 BSC 1.60 BSC PIN 1 INDICATOR 0.95 BSC 1.90 BSC 1.30 1.15 0.90 1.45 MAX 0.50 0.30 0.15 MAX 0.22 0.08 10 4 0 SEATING PLANE 0.60 0.45 0.30 COMPLIANT TO JEDEC STANDARDS MO-178AB 8-Lead Mini Small Outline Package [MSOP] (RM-8) Dimensions shown in millimeters 3.00 BSC 8 5 4.90 BSC 3.00 BSC 1 4 PIN 1 0.65 BSC 1.10 MAX 0.15 0.00 0.38 0.22 COPLANARITY 0.10 0.23 0.08 8 0 0.80 0.60 0.40 SEATING PLANE COMPLIANT TO JEDEC STANDARDS MO-187AA Revision History Location Page 8/04--Data Sheet Changed from REV. D to REV. E. Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Changes to CONVERTER DETAILS section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Changes to Read Operation section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5/02--Data Sheet Changed from REV. C to REV. D. Updates to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 -8- REV. E