Microphone Preamplifier with Variable Compression and Noise Gating SSM2166* this gain is in addition to the variable gain in other compression settings. The input buffer can also be configured for front-end gains of 0 dB to 20 dB. A downward expander (noise gate) prevents amplification of noise or hum. This results in optimized signal levels prior to digitization, thereby eliminating the need for additional gain or attenuation in the digital domain that could add noise or impair accuracy of speech recognition algorithms. The compression ratio and time constants are set externally. A high degree of flexibility is provided by the VCA Gain, Rotation Point, and Noise Gate adjustment pins. FEATURES Complete Microphone Conditioner in a 14-Lead Package Single +5 V Operation Adjustable Noise Gate Threshold Compression Ratio Set by External Resistor Automatic Limiting Feature--Prevents ADC Overload Adjustable Release Time Low Noise and Distortion Power-Down Feature 20 kHz Bandwidth (1 dB) Low Cost The SSM2166 is an ideal companion product for audio codecs used in computer systems, such as the AD1845 and AD1847. The device is available in a 14-lead SOIC package, and is guaranteed for operation over the extended industrial temperature range of -40C to +85C. For similar features and performance in an 8-lead package, please refer to the SSM2165. APPLICATIONS Microphone Preamplifier/Processors Computer Sound Cards Public Address/Paging Systems Communication Headsets Telephone Conferencing Guitar Sustain Effects Generators Computerized Voice Recognition Surveillance Systems Karaoke and DJ Mixers 10 OUTPUT - dBu -10 GENERAL DESCRIPTION The SSM2166 integrates a complete and flexible solution for conditioning microphone inputs in computer audio systems. It is also excellent for improving vocal clarity in communications and public address systems. A low noise voltage-controlled amplifier (VCA) provides a gain that is dynamically adjusted by a control loop to maintain a set compression characteristic. The compression ratio is set by a single resistor and can be varied from 1:1 to over 15:1 relative to a user defined "rotation point"; signals above the rotation point are limited to prevent overload and eliminate "popping." In the 1:1 compression setting, the SSM2166 can be programmed with a fixed gain of up to 20 dB; 5 BUFOUT 6 -IN REV. B 1F RATIO = 1:1 -30 -60 -70 -60 -50 3 VCAIN 10F* + VCAR 1k V+ 0 2 9 11 10 8 + AVG 25k CAP 22F GND 500k NOISE GATE SET CONTROL SSM2166 2.3k VCA GAIN ADJ 13 OUTPUT VCA 0.1F 1 -10 14 1k 12 -20 V+ 4 BUFFER POWER DOWN -40 -30 INPUT - dBu Figure 1. SSM2166 Compression and Gating Characteristics with 10 dB of Fixed Gain (The Gain Adjust Pin Can Be Used to Vary This Fixed Gain Amount) 7 R2 = 10k *Patents pending. -20 -50 LEVEL DETECTOR + RATIO = 2:1 -40 10F + R1 = 10k AUDIO +IN RATIO = 10:1 0 17k ROTATION POINT SET COMPRESSION RATIO SET *OPTIONAL Figure 2. Functional Block Diagram and Typical Speech Application Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective companies. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 (c) 2003 Analog Devices, Inc. All rights reserved. R = 100 k, R = 600 k, R = 3 k, R = 0 , , T = 25C, unless otherwise noted, V = 300 mV rms.) SSM2166-SPECIFICATIONS R1(V+==05,V, fR2= 1=kHz, L GATE ROTATION A Parameter AUDIO SIGNAL PATH Voltage Noise Density Noise Total Harmonic Distortion Input Impedance Output Impedance Load Drive Symbol Conditions en 15:1 Compression 20 kHz Bandwidth, VIN = GND 2nd and 3rd Harmonics, VIN = -20 dBu 22 kHz Low-Pass Filter THD+N 17 -109 0.25 Max Unit 0.5 nV/Hz dBu1 % 2 k k nF 5 1% THD 1% THD 1 1 V rms V rms 1% THD 1% THD 1:1 Compression, VCA G = 60 dB 1 1.4 30 V rms V rms MHz 60 -60 to +19 1:1 15:1 5 See TPC 3 for RCOMP/RROT 15:1 Compression, Rotation Point = -10 dBu 4.5 VS ISY 7.5 2.2 50 PSRR POWER DOWN Supply Current Typ 180 75 Resistive Capacitive CONTROL SECTION VCA Dynamic Gain Range VCA Fixed Gain Range Compression Ratio, Min Compression Ratio, Max Control Feedthrough POWER SUPPLY Supply Voltage Range Supply Current Quiescent Output Voltage Level Power Supply Rejection Ratio Min ZIN ZOUT Buffer Input Voltage Range Output Voltage Range VCA Input Voltage Range Output Voltage Range Gain Bandwidth Product COMP IN Pin 12 = V+2 10 dB dB mV 5.5 10 V mA V dB 100 A NOTES 1 0 dBu = 0.775 V rms. 2 Normal operation: Pin 12 = 0 V. Specifications subject to change without notice. ORDERING GUIDE ABSOLUTE MAXIMUM RATINGS Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +10 V Audio Input Voltage . . . . . . . . . . . . . . . . . . . . . Supply Voltage Operating Temperature Range . . . . . . . . . . . . -40C to +85C Storage Temperature Range . . . . . . . . . . . . . -65C to +150C Junction Temperature (TJ ) . . . . . . . . . . . . . . . . . . . . . . 150C Lead Temperature (Soldering, 60 sec) . . . . . . . . . . . . . 300C Model Temperature Range Package Description Package Option SSM2166S -40C to +85C Narrow SOIC R-14 ESD RATINGS 883 (Human Body) Model . . . . . . . . . . . . . . . . . . . . . . 2.0 kV THERMAL CHARACTERISTICS Thermal Resistance 14-Lead SOIC JA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120C/W JC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36C/W CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the SSM2166 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. -2- REV. B SSM2166 PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Function 1 2 GND GAIN ADJUST Ground VCA Gain Adjust Pin. A resistor from this pin to ground sets the fixed gain of the VCA. To check the setting of this pin, make sure the compression pin (Pin 10) is grounded for no compression. The gain can be varied from 0 dB to 20 dB. For 20 dB, leave the pin open. For 0 dB of fixed gain, a typical resistor value is approximately 1 k. For 10 dB of fixed gain, the resistor value is approximately 2 k to 3 k. For resistor values <1 k, the VCA can attenuate or mute. Refer to TPC 4. 3 VCAIN VCA Input Pin. A typical connection is a 10 F capacitor from the buffer output pin (Pin 5) to this pin. 4 VCAR Inverting Input to the VCA. This input can be used as a nonground reference for the audio input signal (see Application Information). 5 BUF OUT Input Buffer Amplifier Output Pin. Must not be loaded by capacitance to ground. 6 -IN Inverting Input to the Buffer. A 10 k feedback resistor R1 from the buffer output Pin 5 to this input pin, and a resistor R2, from this pin through a 1 F capacitor to ground gives gains of 6 dB to 20 dB for R2 = 10 k to 1.1 k. 7 AUDIO +IN Input Audio Signal. The input signal should be ac-coupled (0.1 F typical) into this pin. 8 AVG CAP Detector Averaging Capacitor. A capacitor, 2.2 F to 22 F, to ground from this pin is the averaging capacitor for the detector circuit. 9 NOISE GATE SET Noise Gate Threshold Set Point. A resistor to V+ sets the level below which input signals are downward expanded. For a 0.7 mV threshold, the resistor value is approximately 380 k. Increasing the resistor value reduces the threshold. See TPC 2. 10 COMP RATIO SET Compression Ratio Set Pin. A resistor to ground from this pin sets the compression ratio as shown in Figure 1. TPC 3 gives resistor values for various rotation points. 11 ROTATION SET Rotation Point Set Pin. This is set by a resistor to the positive supply. This resistor together with the gain adjust pin determines the onset of limiting. A typical value for this resistor is 17 k for a 100 mV "rotation point." Increasing the resistor value reduces the level at which limiting occurs. Refer to TPC 7. 12 POWER DOWN Power-Down Pin. Connect to ground for normal operation. Connect to positive supply for power-down mode. 13 OUTPUT Output Signal 14 V+ Positive Supply, +5 V Nominal PIN CONFIGURATION 14 V+ GND 1 13 OUTPUT GAIN ADJUST 2 VCAIN 3 SSM2166 12 POWER DOWN TOP VIEW 11 ROTATION SET BUF OUT 5 (Not to Scale) 10 COMP RATIO SET VCAR 4 -IN 6 9 NOISE GATE SET 8 AVG CAP AUDIO +IN 7 REV. B -3- SSM2166-Typical Performance Characteristics 0 20 COMP RATIO = 15:1 COMP RATIO = 10:1 COMP RATIO = 5:1 -10 18 16 -20 GAIN - dB OUTPUT - dBu 14 -30 COMP RATIO = 2:1 -40 -50 -60 -70 COMP RATIO = 1:1 -80 -80 -70 -60 TA = +25C V+ = 5V VIN = 300mV rms @ 1kHz RL = 100k NOISE GATE SETTING 550V rms ROTATION POINT 300mV rms GAIN ADJUST (PIN 2) = 1.25k -50 -40 -30 INPUT - dBu -20 -10 TA = +25C V+ = 5V RL = 100k VIN = 100mV rms @ 1kHz NOISE GATE SETTING 550V rms ROTATION POINT (PIN 11) 1V rms COMPRESSION RATIO = 1:1 10 8 6 4 2 0 0 TPC 1. Output vs. Input Characteristics 0 2 4 6 8 10 12 14 16 18 20 22 24 GAIN ADJUST RESISTOR - k 26 28 30 TPC 4. VCA Gain vs. RGAIN (Pin 2 to GND) 100 5 TA = +25C V+ = 5V RL = 100k COMPRESSION RATIO = 2:1 ROTATION POINT 1V rms GAIN ADJUST (PIN 2) = 1.25k 10 TA = +25C V+ = 5V COMPRESSION RATIO = 1:1 NOISE GATE SETTING 550V rms ROTATION POINT 1V rms GAIN ADJUST (PIN 2) = 1.25k VIN FREQUENCY = 1kHz 1 THD + N - % NOISE GATE - mV rms 12 1 RL = 10k RL = 100k 0.1 0.1 0 0.05 0.01 50 100 150 200 250 300 350 400 450 500 550 600 650 0.1 INPUT VOLTAGE - V rms RGATE - k 1 TPC 5. THD + N (%) vs. Input (V rms) TPC 2. Noise Gate vs. RGATE (Pin 9 to V+) 5 COMPRESSION RATIO 1 1:1 2:1 5:1 10:1 15:1 100mV rms 0 12.5 96 215 395 300mV rms 0 12.5 96 215 395 1V rms 0 12.5 96 215 395 THD + N - % ROTATION POINT TA = +25C V+ = 5V VIN = 77.5mV rms @ 1kHz COMPRESSION RATIO = 1:1 NOISE GATE SETTING 550V rms ROTATION POINT 1V rms GAIN ADJUST (PIN 2) = 1.2k MEASUREMENT FILTER BW: 22Hz TO 30kHz 0.1 RCOMP - k, TYPICAL 0.05 20 100 1k FREQUENCY - Hz 10k 30k TPC 6. THD + N (%) vs. Frequency (Hz) TPC 3. Compression Ratio vs. RCOMP (Pin 10 to GND) -4- REV. B SSM2166 1.0 -10 TA = +25C V+ = 5V RL = 100k -20 -30 PSRR - dB ROTATION POINT - V rms COMPRESSION RATIO = 1:1 NOISE GATE SETTING 550V rms GAIN ADJUST (PIN 2) = 1.25k RCOMP = 0 RGAIN = 1.24k RGATE = 500k RROT = 1.74k 0.1 V+ = 51V p-p -40 -50 V+ = 50.5V p-p -60 -70 0.01 0 -80 20 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 RROT PT RESISTOR - k 1k FREQUENCY - Hz 10k TPC 8c. PSRR vs. Frequency TPC 7. Rotation Point vs. RROT PT (Pin 11 to V+) 5V 100 20mV 1s 100 100 90 90 TA = +25C CAVG = 2.2F TA = +25C COMPRESSION RATIO = 15:1 NOISE BW = 20kHz 10 0% 10 SYSTEM GAIN = 0dB RL = 10k 0% COMP RATIO = 1:1 10s TPC 9. Small Signal Transient Response TPC 8a. Wideband Output Noise 70 G = 60dB 200mV 60 100 50 90 G = 40dB GAIN - dB 40 30 G = 20dB 20 10 0 -10 -20 1k ROTATION POINT = 1.13V rms NOISE GATE SETTING = 336V rms RCOMP = 40k VIN = 400V rms 10 0% 10s 10k 100k FREQUENCY - Hz 1M TPC 10. Large Signal Transient Response TPC 8b. GBW Curves vs. VCA Gain REV. B TA = +25C CAVG = 2.2F SYSTEM GAIN = 0dB RL = 10k COMP RATIO = 1:1 -5- 30k SSM2166 APPLICATION INFORMATION LIMITING THRESHOLD (ROTATION POINT) OUTPUT - dB The SSM2166 is a complete microphone signal conditioning system on a single integrated circuit. Designed primarily for voice-band applications, this integrated circuit provides amplification, rms detection, limiting, variable compression, and downward expansion. An integral voltage-controlled amplifier (VCA) provides up to 60 dB of gain in the signal path with approximately 30 kHz bandwidth. Additional gain is provided by an input buffer op amp circuit that can be set anywhere from 0 dB to 20 dB, for a total signal path gain of up to 80 dB. The device operates on a single +5 V supply, accepts input signals up to 1 V rms, and produces output signal levels >1 V rms (3 V p-p) into loads >5 k. The internal rms detector has a time constant set by an external capacitor. LIMITING REGION DOWNWARD COMPRESSION REGION EXPANSION THRESHOLD 1 (NOISE GATE) r VCA GAIN DOWNWARD EXPANSION REGION 1 1 VDE VRP INPUT - dB The SSM2166 contains an input buffer and automatic gain control (AGC) circuit for audio- and voice-band signals. Circuit operation is optimized by providing a user adjustable time constant and compression ratio. A downward expansion (noise gating) feature eliminates circuit noise in the absence of an input signal. The SSM2166 allows the user to set the downward expansion threshold, the limiting threshold (rotation point), input buffer fixed gain, and the internal VCA's nominal gain at the rotation point. The SSM2166 also features a power-down mode and muting capability. Figure 3. General Input/Output Characteristics of the SSM2166 SSM2166 Signal Path Figure 4 illustrates the block diagram of the SSM2166. The audio input signal is processed by the input buffer and then by the VCA. The input buffer presents an input impedance of approximately 180 k to the source. A dc voltage of approximately 1.5 V is present at AUDIO +IN (Pin 7 of the SSM2166), requiring the use of a blocking capacitor (C1) for groundreferenced sources. A 0.1 F capacitor is a good choice for most audio applications. The input buffer is a unity-gain stable amplifier that can drive the low impedance input of the VCA. Theory of Operation Figure 3 illustrates a typical transfer characteristic for the SSM2166 where the output level in dB is plotted as a function of the input level in dB. The dotted line indicates the transfer characteristic for a unity-gain amplifier. For input signals in the range of VDE (Downward Expansion) to VRP (Rotation Point), an "r" dB change in the input level causes a 1 dB change in the output level. Here, "r" is defined as the "compression ratio." The compression ratio may be varied from 1:1 (no compression) to over 15:1 via a single resistor, RCOMP. Input signals above VRP are compressed with a fixed compression ratio of approximately 15:1. This region of operation is the "limiting region." Varying the compression ratio has no effect on the limiting region. The breakpoint between the compression region and the limiting region is referred to as the "limiting threshold" or the "rotation point," and is user specified in the SSM2166. The term "rotation point" derives from the observation that the straight line in the compression region "rotates" about this point on the input/ output characteristic as the compression ratio is changed. The VCA is a low distortion, variable-gain amplifier whose gain is set by the side-chain control circuitry. The input to the VCA is a virtual ground in series with approximately 1 k. An external blocking capacitor (C6) must be used between the buffer's output and the VCA input. The 1 k impedance between amplifiers determines the value of this capacitor, which is typically between 4.7 F and 10 F. An aluminum electrolytic capacitor is an economical choice. The VCA amplifies the input signal current flowing through C6 and converts this current to a voltage at the SSM2166's output pin (Pin 13). The net gain from input to output can be as high as 60 dB (without additional buffer gain), depending on the gain set by the control circuitry. The gain of the VCA at the rotation point is set by the value of a resistor connected between Pin 2 and GND, RGAIN. The relationship between the VCA gain and RGAIN is shown in TPC 4. The AGC range of the SSM2166 can be as high as 60 dB. The VCAIN pin (Pin 3) on the SSM2166 is the noninverting input terminal to the VCA. The inverting input of the VCA is also available on the SSM2166's Pin 4 (VCAR) and exhibits an input impedance of 1 k, as well. As a result, this pin can be used for differential inputs or for the elimination of grounding problems by connecting a capacitor whose value equals that used in series with the VCAIN pin, to ground. See Figure 12, Evaluation Board, for more details. The gain of the system with an input signal level of VRP is fixed by RGAIN regardless of the compression ratio, and is the "nominal gain" of the system. The nominal gain of the system may be increased by the user via the on-board VCA by up to 20 dB. Additionally, the input buffer of the SSM2166 can be configured to provide fixed gains of 0 dB to 20 dB with R1 and R2. Input signals below VDE are downward expanded; that is, a -1 dB change in the input signal level causes approximately a -3 dB change in the output level. As a result, the gain of the system is small for very small input signal levels, even though it may be quite large for small input signals above VDE. The downward expansion threshold, VDE, is set externally by the user via RGATE at Pin 9 (NOISE GATE). Finally, the SSM2166 provides an active high, CMOS compatible digital input whereby a power-down feature will reduce device supply current to less than 100 A. The output impedance of the SSM2166 is typically less than 75 , and the external load on Pin 13 should be >5 k. The nominal output dc voltage of the device is approximately 2.2 V. Use a blocking capacitor for grounded loads. The bandwidth of the SSM2166 is quite wide at all gain settings. The upper 3 dB point is approximately 30 kHz at gains as high as 60 dB (using the input buffer for additional gain, circuit -6- REV. B SSM2166 C7* 10F C6 10F V+ 5 3 BUFOUT VCAIN VCAR 1k 1k 14 R1 = 10k INPUT BUFFER 4 -IN 6 AUDIO +IN OUTPUT 13 VOUT VCA 7 GAIN ADJUST 0.1F 2 SSM2166 R2 = 10k + 1F RMS LEVEL DETECTOR CONTROL CIRCUITRY NOISE GATE AVG CAP 1 8 RGATE 9 ROTATION POINT ADJUST 11 POWER DOWN GND V+ RGAIN 12 COMPRESSION RATIO SET RROT PT POWER DOWN 10 CAVG 2.2F RCOMP *OPTIONAL GND Figure 4. Functional Block Diagram and Typical Application bandwidth is unaffected). The GBW plots are shown in TPC 8b. The lower 3 dB cutoff frequency of the SSM2166 is set by the input impedance of the VCA (1 k) and C6. While the noise of the input buffer is fixed, the input referred noise of the VCA is a function of gain. The VCA input noise is designed to be a minimum when the gain is at a maximum, thereby optimizing the usable dynamic range of the part. An image of the SSM2166's wideband peak-to-peak output noise is illustrated in TPC 8a. by internal circuitry that speeds up the attack for large level changes. This limits overload time to under 1 ms in most cases. The performance of the rms level detector is illustrated in Figure 5 for a CAVG of 2.2 F (Figure 5a) and 22 F (Figure 5b). In each of these images, the input signal to the SSM2166 (not shown) is a series of tone bursts in six successive 10 dB steps. The tone bursts range from -66 dBV (0.5 mV rms) to -6 dBV (0.5 V rms). As illustrated in the images, the attack time of the rms level detector is dependent only on CAVG, but the release times are linear ramps whose decay times are dependent on both CAVG and the input signal step size. The rate of release is approximately 240 dB/s for a CAVG of 2.2 F, and 12 dB/s for a CAVG of 22 F. Level Detector The SSM2166 incorporates a full-wave rectifier and a patentpending, true rms level detector circuit whose averaging time constant is set by an external capacitor connected to the AVG CAP pin (Pin 8). For optimal low frequency operation of the level detector down to 10 Hz, the value of the capacitor should be 2.2 F. Some experimentation with larger values for the AVG CAP may be necessary to reduce the effects of excessive low frequency ambient background noise. The value of the averaging capacitor affects sound quality: too small a value for this capacitor may cause a "pumping effect" for some signals, while too large a value can result in slow response times to signal dynamics. Electrolytic capacitors are recommended here for lowest cost and should be in the range of 2 F to 47 F. Capacitor values from 18 F to 22 F have been found to be more appropriate in voice-band applications, where capacitors on the low end of the range seem more appropriate for music program material. 100mV 100 -66dBV 10 -85dBV 0% 100ms The rms detector filter time constant is approximately given by 10 CAVG milliseconds where CAVG is in F. This time constant controls both the steady-state averaging in the rms detector as well as the release time for compression; that is, the time it takes for the system gain to react when a large input is followed by a small signal. The attack time, the time it takes for the gain to be reduced when a small signal is followed by a large signal, is controlled partly by the AVG CAP value, but is mainly controlled REV. B -6dBV 90 Figure 5a. RMS Level Detector Performance with CAVG = 2.2 F -7- SSM2166 Rotation Point An internal dc reference voltage in the control circuitry, used to set the rotation point, is user specified, as illustrated in TPC 7. The effect on rotation point is shown in Figure 7. By varying a resistor, RROT PT, connected between the positive supply and the ROTATION POINT SET pin (Pin 11), the rotation point may be varied from approximately 20 mV rms to 1 V rms. From the figure, the rotation point is inversely proportional to RROT PT. For example, a 1 k resistor would typically set the rotation point at 1 V rms, whereas a 55 k resistor would typically set the rotation point at approximately 30 mV rms. 1S 100mV 100 -6dBV 90 -66dBV 10 Since limiting occurs for signals larger than the rotation point (VIN > VRP), the rotation point effectively sets the maximum output signal level. It is recommended that the rotation point be set at the upper extreme of the range of typical input signals so that the compression region will cover the entire desired input signal range. Occasional larger signal transients will then be attenuated by the action of the limiter. -85dBV 0% Figure 5b. RMS Level Detector Performance with CAVG = 22 F Control Circuitry The output of the rms level detector is a signal proportional to the log of the true rms value of the buffer output with an added dc offset. The control circuitry subtracts a dc voltage from this signal, scales it, and sends the result to the VCA to control the gain. The VCA's gain control is logarithmic--a linear change in control signal causes a dB change in gain. It is this control law that allows linear processing of the log rms signal to provide the flat compression characteristic on the input/output characteristic shown in Figure 3. OUTPUT - dB r:1 VCA GAIN Compression Ratio Changing the scaling of the control signal fed to the VCA causes a change in the circuit's compression ratio, "r." This effect is shown in Figure 6. The compression ratio can be set by connecting a resistor between the COMP RATIO pin (Pin 10) and GND. Lowering RCOMP gives smaller compression ratios as indicated in TPC 3, with values of about 17 k or less resulting in a compression ratio of 1:1. AGC performance is achieved with compression ratios between 2:1 and 15:1, and is dependent on the application. A 100 k potentiometer may be used to allow this parameter to be adjusted. On the evaluation board (Figure 12), an optional resistor can be used to set the compression equal to 1:1 when the wiper of the potentiometer is at its full CCW position. 1 1 VDE Figure 7. Effect of Varying the Rotation Point VCA Gain Setting and Muting The maximum gain of the SSM2166 is set by the GAIN ADJUST pin (Pin 2) via RGAIN. This resistor, with a range between 1 k and 20 k, will cause the nominal VCA gain to vary from 0 dB to approximately 20 dB, respectively. Setting the VCA gain to its maximum can also be achieved by leaving the GAIN ADJUST pin in an OPEN condition (no connect). Figure 8 illustrates the effect on the transfer characteristic by varying this parameter. For low level signal sources, the VCA should be set to maximum gain using a 20 k resistor. 15:1 5:1 VCA GAIN 2:1 OUTPUT - dB VRP1 VRP2 VRP3 INPUT - dB 1:1 1 1 VDE INPUT - dB VRP Figure 6. Effect of Varying the Compression Ratio -8- REV. B SSM2166 r:1 r:1 OUTPUT - dB OUTPUT - dB VCA GAIN VCA GAIN 1 1 1 1 VDE INPUT - dB VRP VDE2 VDE1 VDE3 Figure 8. Effect of Varying the VCA Gain Setting Power-Down Feature The supply current of the SSM2166 can be reduced to under 100 A by applying an active high, 5 V CMOS compatible input to the SSM2166's POWER DOWN pin (Pin 12). In this state, the input and output circuitry of the SSM2166 will assume a high impedance state; as such, the potentials at the input pin and the output pin will be determined by the external circuitry connected to the SSM2166. The SSM2166 takes approximately 200 ms to settle from a POWER-DOWN to POWER-ON command. For POWER-ON to POWER-DOWN, the SSM2166 requires more time, typically less than 1 second. Cycling the power supply to the SSM2166 can result in quicker settling times: the off-to-on settling time of the SSM2166 is less than 200 ms, while the on-to-off settling time is less than 1 ms. In either implementation, transients may appear at the output of the device. To avoid these output transients, use mute control of the VCA's gain as previously mentioned. SSM2166 GAIN ADJUST 2 330 RGAIN MUTE (CLOSED SWITCH) PC Board Layout Considerations NOTE: ADDITIONAL CIRCUIT DETAILS OMITTED FOR CLARITY. Since the SSM2166 is capable of wide bandwidth operation and can be configured for as much as 80 dB of gain, special care must be exercised in the layout of the PC board that contains the IC and its associated components. The following applications hints should be considered and/or followed: Figure 9. Details of SSM2166 Mute Option Downward Expansion Threshold The downward expansion, or noise gate, threshold is determined via a second reference voltage internal to the control circuitry. This second reference can be varied in the SSM2166 using a resistor, RGATE, connected between the positive supply and the NOISE GATE SET pin (Pin 9) of the SSM2166. The effect of varying this threshold is shown in Figure 10. The downward expansion threshold may be set between 300 V rms and 20 mV rms by varying the resistance value between Pin 9 and the supply voltage. Like the ROTATION PT ADJUST, the downward expansion threshold is inversely proportional to the value of this resistance: setting this resistance to 1 M sets the threshold at approximately 250 V rms, whereas a 10 k resistance sets the threshold at approximately 20 mV rms. This relationship is illustrated in TPC 2. A potentiometer network is provided on the evaluation board for this adjustment. In general, the downward expansion threshold should be set at the lower extreme of the desired range of the input signals, so that signals below this level will be attenuated. REV. B VRP Figure 10. Effect of Varying the Downward Expansion (Noise Gate) Threshold The gain of the VCA can be reduced below 0 dB by making RGAIN smaller than 1 k. Switching Pin 2 through 330 or less to ground will mute the output. Either a switch connected to ground or a transistor may be used, as shown in Figure 9. To avoid audible "clicks" when using this mute feature, a capacitor (C5 in figure) can be connected from Pin 2 to GND. The value of the capacitor is arbitrary and should be determined empirically, but a 0.01 F capacitor is a good starting value. C5 INPUT - dB (1) In some high system gain applications, the shielding of input wires to minimize possible feedback from the output of the SSM2166 back to the input circuit may be necessary. (2) A single-point ("star") ground implementation is recommended in addition to maintaining short lead lengths and PC board runs. The evaluation board layout shown in Figure 13 for the SSM2166 demonstrates the single-point grounding scheme. In applications where an analog ground and a digital ground are available, the SSM2166 and its surrounding circuitry should be connected to the system's analog ground. As a result of these recommendations, wire-wrap board connections and grounding implementations are to be explicitly avoided. (3) The internal buffer of the SSM2166 was designed to drive only the input of the internal VCA and its own feedback network. Stray capacitive loading to ground from the BUFOUT pin in excess of 5 pF to 10 pF can cause excessive phase shift and can lead to circuit instability. -9- SSM2166 (4) When using high impedance sources (5 k), system gains in excess of 60 dB are not recommended. This configuration is rarely appropriate, as virtually all high impedance inputs provide larger amplitude signals that do not require as much amplification. When using high impedance sources, however, it can be advantageous to shunt the source with a capacitor to ground at the input pin of the IC (Pin 7) to lower the source impedance at high frequencies, as shown in Figure 11. A capacitor with a value of 1000 pF is a good starting value and sets a low-pass corner at 31 kHz for 5 k sources. In applications where the source ground is not as "clean" as would be desirable, a capacitor (illustrated as C7 on the evaluation board) from the VCAR input to the source ground might prove beneficial. This capacitor is used in addition to the grounded capacitor (illustrated as C2 on the evaluation board) used in the feedback around the buffer, assuming that the buffer is configured for gain. C1 0.1F AUDIO IN (RS > 5k) 7 The value of the C7 should be the same as C6, the capacitor value used between BUFOUT and VCAIN. This connection makes the source ground noise appear as a common-mode signal to the VCA, allowing the common-mode noise to be rejected by the VCA's differential input circuitry. C7 can also be useful in reducing ground loop problems and in reducing noise coupling from the power supply by balancing the impedances connected to the inputs of the internal VCA. SSM2166 Evaluation Board A schematic diagram of the SSM2166 evaluation board, available upon request from Analog Devices, is illustrated in Figure 12. As a design aid, the layouts for the topside silkscreen and the topside and backside metallization layers are shown in Figures 13a, 13b, and 13c. Although not shown to scale, the finished dimension of the evaluation board is 3.5 inches by 3.5 inches, and comes complete with pin sockets and a sample of the SSM2166. +IN CX 1000pF SSM2166 NOTE: ADDITIONAL CIRCUIT DETAILS OMITTED FOR CLARITY. Figure 11. Circuit Configuration for Use with High Impedance Signal Sources +V C6 10F + R1 10k R4 1k 5 3 R2 10k R12 100k R8 1k CW 14 ROT PT. ADJ 9 NOISE GATE ADJ V+ +INPUT VCAR AVG CAP 4 8 C1 0.1F MIC PWR INPUT JACK 1/8" PHONE 1 C7 10F GND COMP RATIO GAIN ADJUST 2 + C4 22F R9 1k 10 R11 330 3 R10 20k GAIN CW ADJ OUTPUT 13 5 C5 0.01F COMP RATIO 1 2 + J3 12 POWER DN SSM2166 -INPUT 7 C2 1F NOISE GATE R7 1M CW 11 VCAIN BUFOUT 6 ROTATION PT ADJ R3 50k C3 0.1F MUTE SWITCH 4 OP113 R6 100k CW 6 7 OUTPUT JACK RCA PHONO Figure 12. Evaluation Board -10- REV. B SSM2166 Figure 13c. Evaluation Board Backside Metallization (Not to Scale) Figure 13a. Evaluation Board Topside Silkscreen (Not to Scale) Signal sources are connected to the SSM2166 through a 1/8" phone jack where a 0.1 F capacitor couples the input signal to the SSM2166's +IN pin (Pin 7). As shown in Figure 12 and in microphone applications, the phone jack shield can be optionally connected to the board's ground plane (Jumper J1 inserted into board socket pins labeled "1" and "2") or to the SSM2166's VCAR input at Pin 4 (Jumper J1 inserted into board socket pins labeled "1" and "3"). If the signal source is a waveform or function generator, the phone jack shield is to be connected to ground. Figure 13b. Evaluation Board Topside Metallization (Not to Scale) For ease in making adjustments for all of the SSM2166's configuration parameters, single-turn potentiometers are used throughout. Optional Jumper J2 connects the COMP RATIO pin to ground and sets the SSM2166 for no compression (that is, compression ratio = 1:1). Optional Jumper J3 connects the SSM2166's POWER DOWN input to ground for normal operation. Jumper J3 can be replaced by an open-drain logic buffer for a digitally controlled shutdown function. An output signal mute function can be implemented on the SSM2166 by connecting the GAIN ADJUST pin (Pin 2) through a 330 resistance to ground. This is provided on the evaluation board via R11 and S1. A capacitor C5, connected between Pin 2 and ground and provided on the evaluation board, can be used to avoid audible "clicks" when using the mute function. To configure the SSM2166's input buffer for gain, provisions for R1, R2, and C2 have been included. To configure the input buffer for unity-gain operation, R1 and R2 are removed, and a direct connection is made between the -IN pin (Pin 6) and the BUFOUT pin (Pin 5) of the SSM2166. The output stage of the SSM2166 is capable of driving >1 V rms (3 V p-p) into >5 k loads, and is externally available through an RCA phono jack provided on the board. If the output of the SSM2166 is required to drive a lower load resistance or an audio cable, then the on-board OP113 can be used. To use the OP113 buffer, insert Jumper J4 into board socket pins labeled "4" and "5" and insert Jumper J5 into board socket pins labeled "6" and "7." If the output buffer is not required, remove Jumper J5 and insert Jumper J4 into board socket pins "5" and "7." There are no blocking capacitors either on the input nor at the output of the buffer. REV. B -11- SSM2166 As a result, the output dc level of the buffer will match the output dc level of the SSM2166, which is approximately 2.3 V. A dc blocking capacitor may be inserted on Pins 6 and 7. An evaluation board and setup procedure is available from your Analog Devices representative. Evaluation Board When building a breadboard, keep the leads to Pins 3, 4, and 5 short. A convenient evaluation board is available from an ADI sales representative. The R and C designations refer to the demonstration board schematic of Figure 12 and parts list, Table I. Setup Procedure with Evaluation Board To illustrate how easy it is to program the SSM2166, we will take a practical example. The SSM2166 will be used to interface an electret-type microphone to a postamplifier. The evaluation board or the circuit configuration shown in Figure 12 can be used. The signal from the microphone was measured under actual conditions to vary from 1 mV to 15 mV. The postamplifier requires no more than 500 mV at its input. The required gain from the SSM2166 is, therefore: GTOT = 20 x log (500/15) = 30 dB We will set the input buffer gain to 20 dB and adjust the VCA gain to 10 dB. The limiting or "rotation" point will be set at 500 mV output. From prior experience, we will start with a 2:1 compression ratio, and a noise gate threshold that operates below 100 V. These objectives are summarized in Figure 14, and we will fine-tune them later on. The transfer characteristic we will implement is illustrated in Figure 15. INPUT RANGE OUTPUT RANGE LIMITING LEVEL COMPRESSION BUFFER GAIN VCA GAIN NOISE GATE OUTPUT - mV 1 The SSM2166 has an input buffer that may be used when the overall gain required exceeds 20 dB, the maximum user selectable gain of the VCA. In our example, the desired output is 500 mV for an input around 15 mV, requiring a total gain of 30 dB. We will set the buffer gain at 20 dB, and adjust the VCA for 10 dB. In the socket pins provided on the evaluation board, insert R1 = 100 k, and R2 = 11 k. The buffer gain has been set to 20 dB (x10). STEP 2. Initializing Potentiometers With power off, preset the potentiometers per the table of Figure 17 below. FUNCTION LIMITING REGION 2 GATE THRESHOLD 1.0 15 10 INPUT - mV Figure 15. Transfer Characteristic AC VOLTMETER STEP 1. Configure the Buffer 40 0.1 OSCILLOSCOPE Figure 16. Test Equipment Setup Note: The SSM2166 processes the output of the buffer, which in our example is 20 dB or 10 times the input level. Use the oscilloscope to verify that the buffer is not being driven into clipping with excessive input signals. In the application, take the minimum gain in the buffer consistent with the average source level as well as the crest factor (ratio of peak to rms). COMPRESSION REGION SSM2166 EVALUATION BOARD AC VOLTMETER Figure 14. Objective Specifications 500 The recommended equipment and configuration is shown in Figure 16. A low noise audio generator with a smooth output adjustment range of 50 V to 50 mV is a suitable signal source. A 40 dB pad would be useful to reduce the level of most generators by 100x to simulate the microphone levels. The input voltmeter could be connected before the pad, and need only go down to 10 mV. The output voltmeter should go up to 2 V. The oscilloscope is used to verify that the output is sinusoidal and that no clipping is occurring in the buffer, and to set the limiting and noise gating "knees." SIGNAL GENERATOR 1 mV-15 mV TO 500 mV 500 mV 2:1 20 dB 10 dB 100 V ROTATION POINT Test Equipment Setup INITIAL INITIAL POT RANGE POSITION RESISTANCE EFFECT OF CHANGE GAIN ADJUST (VCA) R10 0-20 k CCW ZERO 0 dB; CW TO INCREASE VCA GAIN ROTATION POINT R3 0-50 k CCW ZERO 1 V; CW TO REDUCE ROTATION POINT COMPRESSION RATIO R6 0-100 k CCW ZERO 1:1; CW TO INCREASE COMPRESSION NOISE GATE R7 0-1 M CW 1 M 300 V; CCW TO INCREASE THRESHOLD Figure 17. Initial Potentiometer Settings STEP 3. Testing Setup With power on, adjust the generator for an input level of 15 mV, 1 kHz. The output meter should indicate approximately 100 mV. If not, check the setup. STEP 4. Adjusting the VCA Gain Set the input level to 15 mV. Adjust R10--GAIN ADJ CW for an output level of 500 mV. The VCA gain has been set to 10 dB. -12- REV. B SSM2166 will keep the output steady over a range of microphone to speaker distance, and the noise gate will keep the background sounds subdued. STEP 5. Adjusting the Rotation Point Set the input level to 15 mV, and observe the output on the oscilloscope. Adjust R3--ROTATION PT ADJ CW until the output level just begins to drop, then reverse so that the output is 500 mV. The limiting has now been set to 500 mV. STEP 9. Recording Values STEP 6. Adjusting the Compression Ratio Set the input signal for an output of 500 mV but not in limiting. Note the value (around 15 mV). Next, reduce the input to 1/10 the value noted (around 1.5 mV), for a change of -20 dB. Next, adjust R6--COMP RATIO CW until the output is 160 mV, for an output change of -10 dB. The compression, which is the ratio of output change to input change, in dB, has now been set to 2:1. STEP 7. Setting the Noise Gate With the input set at 100 V, observe the output on the oscilloscope, and adjust R7--ROT PT SET CCW until the output drops rapidly. "Rock" the control back and forth to find the "knee." The noise gate has now been set to 100 V. The range of the noise gate is from 0.3 mV to over 0.5 mV relative to the output of the buffer. To fit this range to the application, it may be necessary to attenuate the input or apportion the buffer gain and VCA gain differently. STEP 8. Listening At this time, it may be desirable to connect an electret microphone to the SSM2166 and listen to the results. Be sure to include the proper power for the microphone's internal FET (usually +2 V to +5 V dc through a 2.2 k resistor). Experiment with the settings to hear how the results change. Varying the averaging capacitor, C4, changes the attack and decay times, which are best determined empirically. The compression ratio REV. B With the power removed from the test fixture, measure and record the values of all potentiometers, including any fixed resistance in series with them. If the averaging capacitor, C4, has been changed, note its value, too. SUMMARY We have implemented the transfer condition of Figure 2. For inputs below the 100 V noise gate threshold, circuit and background noise will be minimized. Above it, the output will increase at a rate of 1 dB for each 2 dB input increase, until the 500 mV rotation point is reached at an input of approximately 15 mV. For higher inputs that would drive the output beyond 500 mV, limiting will occur, and there will be little further increase. The SSM2166 processes the output of the buffer, which in our example is 20 dB, or 10 times the input level. Use the oscilloscope to ensure that the buffer is not being driven into clipping with the highest expected input peaks. Always take the minimum gain in the buffer consistent with the average source level and crest factor (ratio of peak to rms). The wide program range of the SSM2166 makes it useful in many applications other than microphone signal conditioning. Other Versions The SSM2165 is an 8-lead version of this microphone preamp with unity buffer gain and preset noise gate threshold. Customized parts are available for large volume users. For further information, contact an ADI sales representative. -13- SSM2166 Table I. SSM2166 Demo Board Parts List R1 R2 R3 R4 R5 R6 R7 R8 R9 R10 R11 R12 C1 C2 C3 C4 C5 C6 C7 IC1 IC2 S1 J1 J2 10 k 10 k 50 k Pot 1 k 0 100 k Pot 1 M Pot 1 k 1 k 20 k Pot 330 100 k 0.1 F 1 F 0.1 F 2.2 F-22 F 0.01 F 10 F 10 F SSM2166P OP113FP SPST 1/8" Mini Phone Plug RCA Female Feedback Input Rotation Point, Adj. Rotation Point, Fixed Comp Ratio, Fixed Comp Ratio, Adj. Noise Gate, Adj. Noise Gate, Fixed Gain Adj., Fixed Gain Adj. Mute Power Down Pull-Up Input DC Block Buffer Low f, G = 1 +V Bypass Avg. Cap Mute Click Suppress Coupling VCA Noise/DC Balance Mic Preamp Op Amp, Output Buffer Mute MIC Input Output Jack -14- REV. B SSM2166 OUTLINE DIMENSIONS 14-Lead Standard Small Outline Package [SOIC] Narrow Body (R-14) Dimensions shown in millimeters and (inches) 8.75 (0.3445) 8.55 (0.3366) 4.00 (0.1575) 3.80 (0.1496) 14 8 1 7 0.25 (0.0098) 0.10 (0.0039) COPLANARITY 0.10 1.27 (0.0500) BSC 0.51 (0.0201) 0.33 (0.0130) 6.20 (0.2441) 5.80 (0.2283) 1.75 (0.0689) 1.35 (0.0531) SEATING PLANE 0.50 (0.0197) 45 0.25 (0.0098) 8 0.25 (0.0098) 0 1.27 (0.0500) 0.40 (0.0157) 0.19 (0.0075) COMPLIANT TO JEDEC STANDARDS MS-012AB CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN REV. B -15- SSM2166 Revision History Location Page 3/03--Data Sheet changed from REV. A to REV. B. Change to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Changes to THERMAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Deleted 14-Lead Plastic DIP, OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 PRINTED IN U.S.A. Updated 14-Lead Narrow-Body SOIC, OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 C00357-0-3/03(B) Deleted Plastic DIP package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Universal -16- REV. B