For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 1
General Description
Features
Functional Diagram
Typical Applications
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
HMC862LP3E
v03.1210
The HMC862LP3E is a low noise programmable
frequency divider in a 3x3 mm leadless surface
mount package. The divider can be programmed
to divide from N=1, 2, 4, 8 in the 100 MHz to
15 GHz input frequency range. The low phase
noise, wide frequency range and exible division
ratio make this device ideal for high performance and
wide band communication systems.
Low Noise Floor: -153 dBc/Hz at 100 kHz offset
Programmable Frequency Divider, N = 1, 2, 4, 8
Wide Bandwidth: 100 MHz to 15 GHz
16 Lead 3X3 mm SMT Package: 9mm2
Electrical Specications, TA = +25° C, Vcc1 = Vcc2 = +5V
The HMC862LP3E is ideal for:
• Satellite Communication Systems
• Point-to-Point & Point-to-Multi-Point Radios
• Military Applications
• Test Equipment
Parameter Conditions Min. Typ. Max. Units
RF Input Characteristics
Max RF Input Frequency Sine Wave or Square Wave Input 15 GHz
Min RF Input Frequency Sine Wave or Square Wave Input [1] 0.1 GHz
RF Input Power Range (N = 1) Sine Wave or Square Wave Input [1] [2] Fin < 8 GHz -10 10 dBm
Sine Wave or Square Wave Input [1] [2] Fin > 8 GHz -10 0 dBm
RF Input Power Range (N = 2, 4, 8) Sine Wave or Square Wave Input [1] -10 10 dBm
Divider Output Characteristics
Output Power (N = 1) (see the Pout plot for N = 1) [2] -2 to +3 dBm
Output Power (N = 2, 4, 8) (see the Pout plots for each division ratio) 2 dBm
Divider Ratio N 1, 2, 4, 8
SSB Phase Noise @ 100 kHz Offset Fin = 6 GHz, Pin = 0 dBm, N = 2 -153 dBc/Hz
Logic Inputs
VIH Input High Voltage 3 5 V
VIL Input Low Voltage 0 0.4 V
Power Supplies
Vcc Analog Supply 4.75 5 5.25 V
Current Consumption
Icc
N = 1, S0 = L, S1 = L, S2 = L 106 mA
N = 2, S0 = H, S1 = L, S2 = L 143 mA
N = 4, S0 = H, S1 = H, S2 = L 153 mA
N = 8, S0 = H, S1 = H, S2 = H 162 mA
Control Bits 3 Bit
[1] Square wave input waveform is recommended below 400 MHz for best phase noise performance. If sine wave input waveform is used below
400 MHz, it is recommended that power input is > +5 dBm for best operation including phase noise performance.
[2] For N = 1, frequencies > 8 GHz, and input power > 0 dBm, output power will saturate and gradually drop with increasing input power, but
part will continue to function.
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 2
Divide-by-1
Input Sensitivity vs. Temperature
Phase Noise vs. Temperature,
Pin = 0 dBm, Fin = 6 GHz
Output Harmonics, Pin = 0 dBm T = 25 °C
Phase Noise vs. Frequency, Pin = 0 dBm
Reverse Leakage, Pin = 0 dBm T = 25 °C
-10
-8
-6
-4
-2
0
2
4
6
8
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
+25C
+85C
-40C
OUTPUT POWER (dBm)
INPUT FREQUENCY (GHz)
-25
-20
-15
-10
-5
0
5
10
15
0 2 4 6 8 10 12 14 16 18 20
Min Pin +25C
Max Pin +25C
Min Pin +85C
Max Pin +85C
Min Pin -40C
Max Pin -40C
INPUT POWER (dBm)
INPUT FREQUENCY (GHz)
-160
-150
-140
-130
-120
1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
+25C
+85C
-40C
SSB PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
-160
-155
-150
-145
-140
-135
-130
-125
-120
1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
100MHz SQ
100MHz SINE
6 GHz
15 GHz
SSB PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
-70
-60
-50
-40
-30
-20
-10
0
10
0 2 4 6 8 10 12 14 16 18 20
Pfeedthru
3rd Harmonic
OUTPUT LEVEL (dBm)
INPUT FREQUENCY (GHz)
Output Power vs. Temperature, Pin = 0 dBm
-50
-40
-30
-20
-10
0
Both Output Ports Terminated
One Output Port Terminated
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
POWER LEVEL (dBm)
INPUT FREQUENCY (GHz)
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 3
Divide-by-2
Input Sensitivity vs. Temperature
Phase Noise vs. Temperature
Pin = 0 dBm, Fin = 6 GHz
Output Harmonics, Pin = 0 dBm T = 25 °C
Phase Noise vs. Frequency, Pin = 0 dBm
Reverse Leakage, Pin = 0 dBm T = 25 °C
-10
-8
-6
-4
-2
0
2
4
6
8
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
+25C
+85C
-40C
OUTPUT POWER (dBm)
INPUT FREQUENCY (GHz)
-25
-20
-15
-10
-5
0
5
10
15
0 2 4 6 8 10 12 14 16 18 20
Min Pin +25C
Max Pin +25C
Min Pin +85C
Max Pin +85C
Min Pin -40C
Max Pin -40C
INPUT POWER (dBm)
INPUT FREQUENCY (GHz)
-160
-150
-140
-130
-120
1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
+25C
+85C
-40C
SSB PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
-170
-160
-150
-140
-130
-120
1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
100MHz SQ
100MHz SINE
6 GHz
15 GHz
SSB PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
-70
-60
-50
-40
-30
-20
-10
0
10
0 2 4 6 8 10 12 14 16 18 20
Pfeedthru
3rd Harmonic
OUTPUT LEVEL (dBm)
INPUT FREQUENCY (GHz)
Output Power vs. Temperature, Pin = 0 dBm
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Both Output Ports Terminated
One Output Port Terminated
POWER LEVEL (dBm)
INPUT FREQUENCY (GHz)
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 4
Divide-by-4
Phase Noise vs. Temperature
Pin = 0 dBm, Fin = 6 GHz
Phase Noise vs. Frequency, Pin = 0 dBm
Input Sensitivity vs. Temperature
Output Harmonics, Pin = 0 dBm T = 25 °C Reverse Leakage, Pin = 0 dBm T = 25 °C
-10
-8
-6
-4
-2
0
2
4
6
8
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
+25C
+85C
-40C
OUTPUT POWER (dBm)
INPUT FREQUENCY (GHz)
-25
-20
-15
-10
-5
0
5
10
15
0 2 4 6 8 10 12 14 16 18 20
Min Pin +25C
Max Pin +25C
Min Pin +85C
Max Pin +85C
Min Pin -40C
Max Pin -40C
INPUT POWER (dBm)
INPUT FREQUENCY (GHz)
-160
-150
-140
-130
-120
1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
+25C
+85C
-40C
SSB PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
-170
-160
-150
-140
-130
-120
1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
100MHz SQ
100MHz SINE
6 GHz
15 GHz
SSB PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
-70
-60
-50
-40
-30
-20
-10
0
10
0 2 4 6 8 10 12 14 16 18 20
Pfeedthru
3rd Harmonic
OUTPUT LEVEL (dBm)
INPUT FREQUENCY (GHz)
Output Power vs. Temperature, Pin = 0 dBm
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Both Output Ports Terminated
One Output Port Terminated
POWER LEVEL (dBm)
INPUT FREQUENCY (GHz)
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 5
Divide-by-8
Input Sensitivity vs. Temperature
Output Harmonics, Pin = 0 dBm T = 25 °C
Output Power vs. Temperature, Pin = 0 dBm
Reverse Leakage, Pin = 0 dBm T = 25 °C
-10
-8
-6
-4
-2
0
2
4
6
8
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
+25C
+85C
-40C
OUTPUT POWER (dBm)
INPUT FREQUENCY (GHz)
-25
-20
-15
-10
-5
0
5
10
15
0 2 4 6 8 10 12 14 16 18 20
Min Pin +25C
Max Pin +25C
Min Pin +85C
Max Pin +85C
Min Pin -40C
Max Pin -40C
INPUT POWER (dBm)
INPUT FREQUENCY (GHz)
-160
-150
-140
-130
-120
1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
+25C
+85C
-40C
SSB PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
-170
-160
-150
-140
-130
-120
1.0e+2 1.0e+3 1.0e+4 1.0e+5 1.0e+6 1.0e+7
100MHz SQ
100MHz SINE
6 GHz
15 GHz
SSB PHASE NOISE (dBc/Hz)
OFFSET FREQUENCY (Hz)
-70
-60
-50
-40
-30
-20
-10
0
10
0 2 4 6 8 10 12 14 16 18 20
Pfeedthru
3rd Harmonic
OUTPUT LEVEL (dBm)
INPUT FREQUENCY (GHz)
Phase Noise vs. Temperature
Pin = 0 dBm, Fin = 6 GHz
Phase Noise vs. Frequency, Pin = 0 dBm
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
0
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Both Output Ports Terminated
One Output Port Terminated
POWER LEVEL (dBm)
INPUT FREQUENCY (GHz)
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 6
Absolute Maximum Ratings Reliability Information
RF Input Power 13 dBm
Supply Voltage (Vcc) 5.5V
Logic Inputs (S0, S1, S2) -0.5V to (0.5V + Vcc)
Storage Temperature -65 to +125 °C
ESD Sensitivity (HBM) Class 1A
Junction Temperature to Maintain
1 Million Hour MTTF 150 °C
Nominal Junction Temperature
(T = 85 °C) 112 °C
Thermal Resistance
(Junction to GND Paddle, 5V Supply) 33 °C/W
Operating Temperature -40 to +85 °C
Digital Control Input Voltages
State S0, S1, S2
Low 0 to 0.4V
High 3V to 5V
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Programming Truth Table
for Frequency Division Ratios
S0 S1 S2 Divider Ratio (N)
0 0 0 1
1 0 0 2
1 1 0 4
1 1 1 8
0 = Logic Low 1 = Logic High
Note: Vcc1, Vcc2 must be applied before logic.
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
Icc vs. Vcc
0
50
100
150
200
4.7 4.8 4.9 5 5.1 5.2 5.3
N = 1
N = 2
N = 4
N = 8
OPERATING CURRENT (mA)
Vcc (V)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 7
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
Outline Drawing
Part Number Package Body Material Lead Finish MSL Rating Package Marking [1]
HMC862LP3E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 [2] 862
XXX
[1] 4-Digit lot number XXXX
[2] Max peak reow temperature of 260 °C
Package Information
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS].
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST
BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED
PCB LAND PATTERN.
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 8
Pin Description
Pin Number Function Description Interface Schematic
1, 4, 8, 9,
12, 14, 15 GND Ground: Backside of package has exposed metal ground slug which
must be connected to RF/DC ground.
2 IN RF Input must be DC blocked.
3 NIN
RF Input 180° out of phase with pin 2 for differential
operation. AC ground for single ended operation. DC
block for differential operation.
5, 6, 7 S0, S1, S2 CMOS compatible division ratio control bit.
See Programming Truth Table
10 NOUT Divider output 180° out of phase with pin 11.
RF output must be DC blocked.
11 OUT Divided Output. RF output must be DC blocked.
13, 16 Vcc1, Vcc2 Supply voltage 5V. Connect both pins to +5V supply.
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 9
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
Evaluation PCB
List of Materials for Evaluation PCB 119351 [1]
Item Description
J1 - J3 PCB Mount SMA-F RF Connector
J4 DC Connector Header, Molex 2mm
C1 - C4 ATC530L, 100 nF, 16V, Broadband Capacitor, 0402 Pkg.
C5, C6 1000 pF Capacitor, 0402 Pkg.
C7, C8 4.7 µF Capacitor, Tantalum, 1206 Pkg.
R1 - R3 10 kOhm Resistor, 0402 Pkg.
Vcc1, Vcc2 Mill-Max 0.040" Dia. PC Pin, 3101-2-00-21-00-00-08-0
U1 HMC862LP3E, Programmable Divider
PCB [2] 119349 Evaluation Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350 or Arlon 25FR
The circuit board used in the application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and backside ground paddle should be
connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
For price, delivery and to place orders: Hittite Microwave Corporation, 20 Alpha Road, Chelmsford, MA 01824
Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com
Application Support: Phone: 978-250-3343 or apps@hittite.com
FREQUENCY DIVIDERS & DETECTORS - SMT
4
4 - 10
Evaluation PCB Schematic
HMC862LP3E
v03.1210
0.1 - 15 GHz LOW NOISE PROGRAMMABLE
DIVIDER (N = 1, 2, 4, 8)
OBSOLETE
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
For price, delivery, and to place orders: Analog Devices, Inc.,
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106
Phone: 781-329-4700 • Order online at www.analog.com
Application Support: Phone: 1-800-ANALOG-D
