KMY Last update: 2015.4.4 No.RMC-K-HTS-0006-9 (Uncontrolled copy) Sp e c i f i c a t i o n (Reference) Title: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE Style: RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RoHS COMPLIANCE ITEM Product specification contained in this specification are subject to change at any time without notice If you have any questions or a Purchasing Specification for any quality Agreement is necessary, please contact our sales staff. Issue Dept.: Research & Development Department Hokkaido Research Center KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 1/18 1. Scope 1.1 This specification covers the detail requirements for fixed thick film chip resistors; rectangular type, style of RMC1/32, 1/20, 1/16S, 1/16, 1/10, 1/8, 1/4, 1/2, 1. 1.2 Applicable documents JIS C 5201-1: 1998, JIS C 5201-8: 1998, JIS C 5201-8-1: 1998 IEC60115-1: 1999, IEC60115-8: 1989 Amendment 1: 1992, IEC60115-8-1: 1989 EIAJ RC-2134B-2002 2. Classification Type designation shall be the following form. (Example) 1) RMC 1/8 123 J TP - 1 2 3 4 5 6 Style 2) RMC 1/8 JP TP 1 2 4 6 Style 1 Fixed thick film chip resistors; rectangular type Style 2 Rated dissipation and / or dimension 3 Temperature coefficient of resistance K 100x10-6/ C -(Dash) Standard 4 Rated resistance Example; 123 12k, Chip jumper: JP 5 Tolerance on rated resistance 6 Packaging form 3. Rating 3.1 The ratings shall be in accordance with Table-1. Table-1(1) Style RMC1/32 Rated dissipation (W) 0.03 Temperature coefficient of resistance (10-6 / C) Standard 200 300 +600-200 RMC1/20 RMC1/16S 0.05 Rated resistance range () Preferred number series for resistors 1001M 1091 4.79.1 1.04.3 E24 200 101M 200 +350-100 +600-200 200 200 +350-100 +600-200 1010M 4.029.76 13.92 101M 1010M 4.39.1 13.9 K 100 101M Standard K 200 100 200 +500-200 200 200 +500-200 1.02M3.3M 101M 1.02M10M 19.76 1010M 1010M 19.1 Standard 0.1 Standard Tolerance on rated resistance F(1%) J(5%) J(5%) B(0.1%) D(0.5%) E24, 96 F(1%) G(2%) E24 E24, 96 J(5%) B(0.1%) D(0.5%) D(0.5%) F(1%) G(2%) E24 J(5%) Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 2/18 Table-1(2) Style Rated dissipation (W) Temperature coefficient of resistance (10-6 / C) 100 103.3M 100 +500-200 200 +500-200 200 +500-200 1010M 19.76 1010M 1.09.1 1022M 1.09.1 K 100 102.2M Standard 200 2.21M3.3M K 100 200 +500-200 200 +500-200 200 +500-200 102.2M 2.21M10M 1.09.76 1010M 1.09.1 1022M 1.09.1 K 100 101M Standard 200 +500-200 200 +500-200 200 +500-200 1.02M10M 1.09.76 1010M 1.09.1 1024M 1.09.1 100 101M 200 +500-200 1.02M10M 1.09.76 101M 1022M 1.09.1 101M 1.09.76 101M 1022M 1.09.1 101M 1.09.76 101M 1022M 1.09.1 K RMC1/16 0.1 Standard RMC1/10 Rated resistance range () 0.125 Standard Preferred number series for resistors E24, 96 0.25 K G(2%) E24 J(5%) E24,96 0.5 Standard RMC1/2 RMC1 0.75 1.0 200 K +500-200 100 +500-200 Standard 200 K +500-200 100 +500-200 Standard 200 +500-200 B(0.1%) D(0.5%) D(0.5%) F(1%) G(2%) E24 J(5%) B(0.1%) D(0.5%) F(1%) F(1%) G(2%) E24 J(5%) E24,96 RMC1/4 B(0.1%) D(0.5%) F(1%) E24,96 RMC1/8 Tolerance on rated resistance B(0.1%) D(0.5%) F(1%) F(1%) G(2%) E24 E24, 96 J(5%) F(1%) G(2%) E24 E24, 96 J(5%) F(1%) G(2%) E24 J(5%) Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 Style Table-1(3) Isolation voltage (V) Limiting element voltage (V) 15 25 RMC-K-HTS-0006 Page: /9 3/18 Category temperature range (C) -55+125 RMC1/32 50 RMC1/20 RMC1/16S 50 100 RMC1/16 RMC1/10 150 -55+155 RMC1/8 500 RMC1/4 200 RMC1/2 RMC1 Note. Rated current of chip jumper: RMC1/32: 0.5(A), RMC1/20, 1/16S: 1(A), RMC1/16, 1/10, 1/8, 1/4, 1/2,1: 2(A) Note. Resistance value of chip jumper: 50 m max. 3.2 Climatic category 3.2.1 RMC1/32 55/125/56 Lower category temperature Upper category temperature Duration of the damp heat, steady state test - 55 C +125 C 56days 3.2.2 RMC1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 55/155/56 Lower category temperature Upper category temperature Duration of the damp heat, steady state test - 55 C +155 C 56days 3.3 Stability class 5% Limits for change of resistance: -for long-term tests (5%+0.1) Chip jumper: 50 m max. -for short-term tests (1%+0.05) Chip jumper: 50 m max. 3.4 Derating The derated values of dissipation (or current rating in case of chip jumper) at temperature in excess of 70 C shall be as indicated by the following curve. 100 Percentage of the rated dissipation (Current) (%) 0 -55 RMC1/20,1/16S,1/16,1/10,1/8,1/4, 1/2,1 RMC1/32 Area of recommended operation 70 125 155 Ambient temperature (C) Figure-1 Derating curve Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 4/18 3.5 Rated voltage d. c. or a. c. r. m. s. voltage calculated from the square root of the product of the rated resistance and the rated dissipation. E : Rated voltage (V) E = P * R P : Rated dissipation (W) R : Rated resistance () Limiting element voltage can only be applied to resistors when the resistance value is equal to or higher than the critical resistance value. At high value of resistance, the rated voltage may not be applicable. 4. Packaging form The standard packaging form shall be in accordance with Table-2. Table-2 Symbol B Packaging form Bulk (loose package) TH TP Press pocket taping (paper taping) Paper taping Paper taping TE Embossed taping PA Standard packaging quantity / units 1,000 pcs. 8mm width, 2mm pitches 8mm width, 2mm pitches 8mm width, 4mm pitches 8mm width, 4mm pitches 12mm width, 4mm pitches 20,000 pcs. 15,000 pcs. 10,000 pcs. 5,000 pcs. 4,000 pcs. Application RMC1/32,1/20,1/16S,1/16,1/10 ,1/8,1/4,1/2,1 RMC1/32 RMC1/20 RMC1/16S,1/16 RMC1/16, 1/10, 1/8 RMC1/4 RMC1/2, 1 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 5/18 5. Dimensions 5.1 The resistor shall be of the design and physical dimensions in accordance with Figure-2 and Table-3. z W z L c d d H c Figure-2 Table-3 Style RMC1/32 RMC1/20 RMC1/16S RMC1/16 RMC1/10 RMC1/8 RMC1/4 RMC1/2 RMC1 Country of origin Japan, Malaysia Japan, Malaysia Malaysia, China Malaysia, China Malaysia, China Malaysia, China Malaysia Malaysia Malaysia L 0.40.02 0.60.03 1.00.05 1.60.1 2.00.1 3.10.1 3.10.1 3.10.15 5.00.15 6.30.15 W 0.20.02 0.30.03 0.50.05 +0.15 0.8-0.05 1.250.10 1.60.15 1.60.1 2.50.15 2.50.15 3.20.15 H 0.130.02 0.230.03 0.350.05 0.450.10 0.550.10 0.550.10 0.60.15 0.550.15 0.550.15 0.550.15 c 0.080.03 0.10.05 0.20.1 0.30.1 0.40.2 0.50.25 0.50.2 0.50.25 0.60.2 0.60.2 d 0.10.03 0.150.05 +0.05 0.25-0.10 0.30.1 0.40.2 0.50.25 0.450.20 0.50.25 0.60.2 0.60.2 Unit : mm z --------- 0.05~0.3 0~0.1 0.05~0.3 0.05~0.35 0.05~0.35 5.2 Net weight (Reference) Style Net weight(mg) RMC1/32 0.035 RMC1/20 0.16 RMC1/16S 0.6 RMC1/16 2 RMC1/10 5 RMC1/8 9 RMC1/4 16 RMC1/2 25 RMC1 40 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 6/18 6. Marking The Rated resistance of RMC1/32, 1/20, 1/16S should not be marked. 6.1 RMC1/10,1/8,1/4,1/2,1 The nominal resistance shall be marked in 3 digits or 4 digits and marked on over coat side. * Malaysia products: E24 series: 3 digits, E96 series: 4 digits In case of the resistance value that E96 overlaps with E24, It is marked by either. * China products(RMC1/10,1/8): J(5%): 3 digits, F(1%): 4 digits Marking example Contents Application Malaysia China 123 123 RMC1/10,1/8,1/4,1/2,1 12x10 3 12 k 2R2 2R2 Less than 10 of RMC1/8,1/4,1/2,1 2. 2 2.2 2R2 Less than 10 of RMC1/10 2. 2 RMC1/10,1/8,1/4,1/2,1 5623 5623 562x10 3 562k 12R7 12R7 12.7 RMC1/10,1/81/4,1/2,1 6.2 RMC1/16 The nominal resistance shall be marked in 3 digits (E24 and/or E96) and marked on over coat side. No marking in the E96 series of a Malaysia. In case of the resistance value that E96 overlaps with E24, there is a case to mark in E96. Marking example Contents Application Malaysia China 3 123 123 E24 12x10 12 k E24 2R2 2R2 2. 2 No marking 02C E96 102x102 [] 10.2 [k] -1 No marking 51X E96 332x10 [] 33.2 [] 6.2.1 Symbol for E96 series of resistance value E96 Symbol E96 Symbol 100 01 162 21 102 02 165 22 105 03 169 23 107 04 174 24 110 05 178 25 113 06 182 26 115 07 187 27 118 08 191 28 121 09 196 29 124 10 200 30 127 11 205 31 130 12 210 32 133 13 215 33 137 14 221 34 140 15 226 35 143 16 232 36 147 17 237 37 150 18 243 38 154 19 249 39 158 20 255 40 E96 261 267 274 280 287 294 301 309 316 324 332 340 348 357 365 374 388 392 402 412 Symbol 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 E96 422 432 442 453 464 475 487 499 511 523 536 549 562 576 590 604 619 634 649 665 Symbol 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 E96 681 698 715 732 750 768 787 806 825 845 866 887 909 931 953 976 Symbol 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 6.2.2 Symbol of multipliers Symbol Y X -2 Multipliers 10 10-1 A 100 6.3 Marking example of Jumper Chip Marking example Contents Malaysia China or 000 000 JP 000 B 101 C 102 D 103 E 104 RMC-K-HTS-0006 Page: /9 7/18 F 105 Application RMC1/16 RMC1/10,1/8 RMC1/4,1/2,1 7. Performance 7.1 The standard condition for tests shall be in accordance with Sub-clause 4.2, JIS C 5201-1: 1998. 7.2 The performance shall be satisfied in Table-4. Table-4(1) No. Test items Performance requirements Condition of test (JIS C 5201-1) 1 Visual examination As in 4.4.1 Sub-clause 4.4.1 The marking shall be legible, as Checked by visual examination. checked by visual examination. 2 Dimension Sub-clause 4.4.2 As specified in Table-3 of this specification. Resistance As in 4.5.2 Sub-clause 4.5 The resistance value shall correspond with the rated resistance taking into account the specified tolerance. Chip jumper: 50m max. 3 Voltage proof Sub-clause 4.7 No breakdown or flash over Method: 4.6.1.4(See Figure-5) Test voltage: Alternating voltage with a peak value of 1.42 times the insulation voltage. Duration: 60 s 5 s R1G Insulation resistance Test voltage: Insulation voltage Duration: 1 min. 4 Solderability As in 4.17.4.5 Sub-clause 4.17 The terminations shall be covered Without ageing Flux: The resistors shall be immersed in a with a smooth and bright solder coating. non-activated soldering flux for 2s. Bath temperature: 235 C 5 C Immersion time: 2 s 0.5 s Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: No 5 6 7 Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 8/18 Table-4(2) Performance requirements Condition of test (JIS C 5201-1) Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Overload Sub-clause 4.13 (in the mounted state) The applied voltage shall be 2.5 times the rated voltage or twice the limiting element voltage, whichever is the less severe. Duration: 2 s No visible damage Visual examination R (1%+0.05) Resistance Chip jumper: 50m max. Solvent resistance of the Sub-clause 4.30 Legible marking marking Solvent: 2-propanol Solvent temperature: 23 C 5 C Method 1 Rubbing material: cotton wool Without recovery Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-4 Bound strength of the end face Sub-clause 4.33 plating Bent value: 3 mm (3225 size max.) 1 mm (5025 siz min.) R (1%+0.05) Resistance Chip jumper: 50m max. Final measurements No visible damage Sub-clause 4.33.6 Visual examination Resistance to soldering heat Sub-clause 4.18 Solder temperature: 260 C 5 C Immersion time: 10 s 0.5 s As in 4.18.3.4 Visual examination No sign of damage such as cracks. Resistance R (1%+0.05) Chip jumper: 50m max. Component solvent resistance Sub-clause 4.29 Solvent: 2-propanol Solvent temperature: 23 C 5 C Method 2 Recovery: 48 h No visible damage Visual examination Resistance R (1%+0.05) Chip jumper: 50m max. Test items Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: No 8 Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 Test items Mounting Adhesion Rapid change temperature 9 Climatic sequence -Dry heat -Damp heat, cycle (12+12hour cycle) First cycle -Cold -Damp heat, cycle (12+12hour cycle) Remaining cycle -D.C. load RMC-K-HTS-0006 Page: /9 9/18 Table-4(3) Performance requirements Condition of test (JIS C 5201-1) Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Sub-clause 4.32 Force: 5 N (RMC1/32: 2N, RMC1/20: 3N) Duration: 10 s 1 s No visible damage Visual examination Sub-clause 4.19 RMC1/32 Lower category temperature: -55 C Upper category temperature: +125 C RMC1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 Lower category temperature: -55 C Upper category temperature: +155 C Duration of exposure at each temperature: 30 min. Number of cycles: 5 cycles. No visible damage Visual examination R (1%+0.05) Resistance Chip jumper: 50m max. Sub-clause 4.23 Sub-clause 4.23.2 RMC1/32 Test temperature: +125 C RMC1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1: Test temperature: +155 C Duration: 16 h Sub-clause 4.23.3 Test method: 2 Test temperature: 55 C [Severity(2)] Sub-clause 4.23.4 Test temperature -55 C Duration: 2h Sub-clause 4.23.6 Test method: 2 Test temperature: 55 C [Severity (2)] Number of cycles: 5 cycles Sub-clause 4.23.7 The applied voltage shall be the rated voltage or the limiting element voltage whichever is the smaller. Duration: 1 min. No visible damage Visual examination R (5%+0.1) Resistance Chip jumper: 50m max. Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: No 10 Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 Test items Mounting Table-4(4) Condition of test (JIS C 5201-1) Sub-clause 4.31 Substrate material: Epoxide woven glass (RMC1may use Alumina substrate.) Test substrate: Figure-3 RMC-K-HTS-0006 Page: /9 10/18 Performance requirements Endurance at 70 C 11 12 Sub-clause 4.25.1 Ambient temperature: 70 C 2 C Duration: 1000 h The voltage shall be applied in cycles of 1.5 h on and 0.5 h off. The applied voltage shall be the rated voltage or the limiting element voltage whichever is the smaller. Examination at 48 h , 500 h and 1000 h: No visible damage Visual examination R (5%+0.1) Resistance Chip jumper: 50m max. Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Variation of resistance with Sub-clause 4.8 As in Table-1 temperature RMC1/32: -55 C / +20 C +20 C / +125C RMC1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1: -55 C / +20 C +20 C / +155C Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Damp heat, steady state Sub-clause 4.24 Ambient temperature: 40 C 2 C Relative humidity : 93 +2 -3 % a) 1st group: without voltage applied. b) 2nd group: The d. c. voltage shall be applied continuously. The voltage shall be accordance with Sub-clause 4.24.2.1 b). without polarizing voltage [4.24.2.1, c)] No visible damage Visual examination Legible marking R (5%+0.1) Resistance Chip jumper: 50m max. Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: No 13 Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 Test items Dimensions (detail) Table-4(5) Condition of test (JIS C 5201-1) Sub-clause 4.4.3 RMC-K-HTS-0006 Page: /9 11/18 Performance requirements As in Table-3 Mounting Sub-clause 4.31 Substrate material: Epoxide woven glass Test substrate: Figure-3 Endurance at upper category Sub-clause 4.25.3 temperature RMC1/32: Ambient temperature:125 C 2 C RMC1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1: Ambient temperature:155 C 2 C Duration: 1000 h Examination at 48 h, 500 h and 1000 h: Visual examination Resistance No visible damage R (5%+0.1) Chip jumper: 50m max. Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 Title: 8. Test substrate RMC-K-HTS-0006 /9 Page: 12/18 c 2.0 4.5 d 7.5 7.5 c Unit: mm a :Copper clad b 40 :Solder resist d Style RMC1/2 RMC 1 10.16 a 4.0 5.0 b 7.5 9.0 60.96 RMC1/2, 1 TEST SUBSTRATE c Soldering land :Solder resist b 25 a 3.5 3 :Copper clad d Unit: mm 7.5 5.5 Style RMC1/32 RMC1/20 RMC1/16S RMC1/16 58.5 RMC1/10 RMC1/4 RMC1/20, 1/16S, 1/16, 1/10 1/4 TEST SUBSTRATE 8 1.5 3 Soldering land b 0.56 1.5 1.9 3.6 4.0 5.0 c 0.2 0.45 0.7 1.0 1.5 2.9 d 5.3 5.2 4.9 4.5 4.3 3.3 Unit: mm :Copper clad :Solder resist 2.5 7.5 5 30 5 4 3.5 2 2.5 2.5 5.08 5.08 2.5 a 0.2 0.3 0.6 1.0 1.2 2.2 1.5 2 2 2 4 2.5 49 RMC1/8 TEST SUBSTRATE Figure-3 Remark 1). Material: Epoxide woven glass Thickness: 1.6mm Thickness of copper clad: 0.035mm 2). In the case of connection by connector, the connecting terminals are gold plated. However, the plating is not necessary when the connection is made by soldering. Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 13/18 Unit: mm :Copper clad 40 c 1 a :Solder resist Style RMC1/2 RMC 1 b a 4.0 5.0 b 7.5 9.0 c 3.0 4.0 100 RMC1/2, 1 BOUND STRENGTH OF THE END FACE PLATING TEST SUBSTRATE Unit: mm a :Copper clad 1 4.5 :Solder resist 40 d c d Style RMC1/20 RMC1/16S RMC1/16 RMC1/10 RMC1/8 RMC1/4 b 70 100 Soldering land a 0.3 0.6 1.0 1.2 2.5 2.2 b 1.1 1.9 3.6 4.0 5.0 5.0 c 0.45 0.7 1.20 1.65 2.0 2.9 d 2.15 2.0 3.0 3.0 2.5 2.5 RMC1/20,1/16S,1/16,1/10,1/8,1/4 BOUND STRENGTH OF THE END FACE PLATING TEST SUBSTRATE Unit: mm :Copper clad 5.5 :Solder resist 40 0.5 70 0.53 0.2 0.5 0.2 0.5 Soldering land 0.56 100 RMC1/32 BOUND STRENGTH OF THE END FACE PLATING TEST SUBSTRATE Thickness: 1.6mm Thickness of copper clad: 0.035mm Figure-4 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 14/18 RMC1/32, 1/20 Insulation plate Metal block measurement Point A V Metal plate R0.25R0.5mm Measurement point B Insulation surface Component Pressure by spring (10.2N) Figure-5 9. Taping 9.1 Applicable documents JIS C 0806-3: 1999, EIAJ ET-7103: 2004, EIAJ ET-7200B: 2003 9.2 Taping dimensions 9.2.1 Press pocket taping (Paper taping, 8mm width, 2mm pitches) Taping dimensions shall be in accordance with Figure-6 and Table-5. Unit: mm 40.05 1.5 +0.1 0 Sprocket hole t1 1.750.1 B 80.2 A t3 20.05 Carrier cavity t2 3.50.05 Direction of unreeling Figure-6 Table-5 Style RMC1/32 RMC1/20 A 0.240.03 0.370.05 B 0.450.03 0.670.05 t1 0.310.03 0.420.03 t2 0.360.02 0.450.05 Unit: mm t3 0.150.02 0.270.02 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 15/18 9.2.2 Paper taping (8mm width, 2mm pitches) Taping dimensions shall be in accordance with Figure-7 and Table-6. 40.1 t1 Sprocket hole 1.5 Unit: mm 0 .1 +0 0 1.750.1 B 80.2 A t2 20.05 Carrier cavity 3.50.05 Direction of unreeling Style RMC1/16S RMC1/16 A 0.65+0.05 -0.10 1.150.15 Figure-7 Table-6 B 1.15 -+0.05 0.10 1.90.2 t1 0.4 0.05 0.60.1 Unit: mm t2 0.5max. 0.8max. 9.2.3 Paper taping (8mm width, 4mm pitches) Taping dimensions shall be in accordance with Figure-8 and Table-7. Unit: mm 40.1 t 1 1.5 Sprocket hole +0.1 0 20.05 1.750.1 B 80.2 A t Carrier cavity 2 40.1 3.50.05 Direction of unreeling Style RMC1/16 RMC1/10 RMC1/8 Figure-8 Table-7 A B 1.150.15 1.90.2 1.650.15 2.50.2 2.000.15 3.60.2 t1 0.60.1 Unit: mm t2 0.8max. 0.80.1 1.0max. Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 16/18 9.2.4 Embossed taping dimensions shall be in accordance with Figure-9 and Table-8. Unit: mm 0.3 max. 20.05 Sprocket hole 1.5+0.1 0 1.750.1 40.1 Carrier cavity t1 Style RMC1/4 RMC1/2 RMC 1 A 2.850.20 3.10.2 3.60.2 W B E A 40.1 Direction of unreeling Figure-9 Table-8 B W 3.50.2 8.00.3 5.50.2 12.00.3 6.90.2 E 3.50.05 Unit: mm t1 1.00.2 5.50.05 1.10.15 1). The cover tapes shall not cover the sprocket holes. 2). Tapes in adjacent layers shall not stick together in the packing. 3). Components shall not stick to the carrier tape or to the cover tape. 4). Pitch tolerance over any 10 pitches 0.2mm. 5). The peel strength of the top cover tape shall be with in 0.1N to 0.5N on the test method as shown in the following RMC1/32,1/20: Figure-10, RMC1/16S, 1/16, 1/10, 1/8: Figure-11, RMC1/4, 1/2, 1: Figure-12. 6). When the tape is bent with the minimum radius for RMC1/32, 1/20, 1/16S, 1/16, 1/10,1/8, 1/4: 25 mm, or RMC1/2, 1: 30 mm, the tape shall not be damaged and the components shall maintain their position and orientation in the tape. 7). In no case shall there be two or more consecutive components missing. The maximum number of missing components shall be one or 0.1%, whichever is greater. 8). The resistors shall be faced to upward at the over coating side in the carrier cavity. Top cover tape Carrier tape 165to180 Peel-off ( About 300mm/ min) Direction of unreeling Figure-10 Top cover tape Carrier tape 165to180 Peel-off ( About 300mm/ min) Direction of unreeling Figure-11 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 17/18 Top cover tape Carrier tape Peel-off (About 300mm/ min) 165to180 Direction of unreeling Figure-12 9.3 Reel dimension Reel dimensions shall be in accordance with the following Figure-13 and Table-9. Plastic reel (Based on EIAJ ET-7200B) Unit: mm 0 +1 60 0 130.2 20.5 180 -1.5 Marking A 210.8 Marking B A B Figure-13 Table-9 Unit: mm B Note Injection molding 11.41.0 RMC1/32, 1/20, 1/16S, 1/16, 1/10, 1/8, 1/4 9 +1.0 0 131.0 Vacuum forming RMC1/2, 1 171.0 Vacuum forming 13 +1.0 0 Note: Marking label shall be marked on a place of Marking A or two place of marking A and B. A Style 9.4 Leader and trailer tape. (Example) 400mm min. 100mm min. 160mm min. End Start Trailer Leader Direction of unreeling Figure-14 Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: Drawing No: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 Page: /9 18/18 10. Marking on package The label of a minimum package shall be legibly marked with follows. 10.1 Marking A (1) Classification (Style, Temperature coefficient of resistance, Rated resistance, Tolerance on rated resistance, Packaging form) (2) Quantity (3) Lot number (4) Manufacturer's name or trade mark 10.2 Marking B (KAMAYA Control label) (5) Others Product specification contained in this specification are subject to change at any time without notice. If you have any questions or a Purchasing Specification for any quality agreement is necessary, please contact our sales staff. Issue: KAMAYA ELECTRIC CO., LTD. Research & Development Department HOKKAIDO Research center Last update: 2015.4.4 KMY Title: FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE RMC1/32,1/20,1/16S,1/16,1/10,1/8,1/4,1/2,1 RMC-K-HTS-0006 9 1 2002.9. 29 2 2006.11.1 2 3 RMC1/16STol:F, TCR1001001M 101M() RMC1/16Tol:F, TCR100101M() 10M10M() Tol: G104.7M() 1010M() 3 2007.10.1 RMC1/2,1 RMC1/32,1/20 1 1.2 EIAJ RC-2134A-1998EIAJ RC-2134B-2002 2 3 RMC1/20Tol:F, TCR+600-20019.76 3 3 RMC1/20.5W0.75W 13 9.1 EIAJ ET-7201A-1996JIS C 0806-6:2006 14 10.1 EIAJ ET-7103:2004 EIAJ ET-7200A:1999EIAJ ET-7200B:2003 17 10.3 EIAJ ET-7200AEIAJ ET-7200B 131.0mm 11 2) B 3 RMC1/32F(1%) (W) RMC1/40.25W0.33W (10-6/) RMC1/201097.6300200 2009/6/3 17 3 5 6 2009/10/1 2010/10/1 17 3 3 7 8 9 2012.10.26 2013.12.1 2015.4.4 1,2 1,2 4 3,9,10,11 4 5 2015.8.31 11 10 2) B 3 RMC1/16 1A 2A 3 RMC1/20 TCR:+600 -200x10-6/ :Tol:F:1.0 9.76( ), J:1.0 9.1( ) TCR+:+600 -200x10-6/:Tol:F:1.03.92(), J:1.03.9() TCR: +350-100x10-6/:Tol:F:4.029.76(), J:4.39.1() RMC1/20,1/16S,1/16,1/10 D(0.5%) 3 RMC1/8,1/4 D(0.5%) RMC1/20,1/16S,1/16,1/10,1/8,1/4 B(0.1%) 1 RMC1/20 3 , 3.2 , 3.4 , 7 No. 8 No. 9 (), No.11 , No.13 ()+125 +155 4 5 RMC1/8 c: 0.450.2 0.50.2 d: 0.50.2 0.450.2 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Walsin: RMC16-102JT RMC1/16104JTP RMC1/16220JTP RMC1/16162JTP RMC1/16562JTP RMC1/16333JTP RMC1/16101JTP RMC1/16202JTP RMC1/16103JTP