LF347, LF347B
JFET-INPUT
QUAD OPERATIONAL AMPLIFIERS
SLOS013B – MARCH 1987 – REVISED AUGUST 1994
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
D
Low Input Bias Current...50 pA Typ
D
Low Input Noise Current
0.01 pA/Hz Typ
D
Low Total Harmonic Distortion
D
Low Supply Current... 8 mA Typ
D
Gain Bandwidth...3 MHz Typ
D
High Slew Rate...13 V/µs Typ
D
Pin Compatible With the LM348
description
These devices are low-cost, high-speed, JFET-input operational amplifiers. They require low supply current yet
maintain a large gain-bandwidth product and a fast slew rate. In addition, their matched high-voltage JFET
inputs provide very low input bias and offset current.
The LF347 and LF347B can be used in applications such as high-speed integrators, digital-to-analog
converters, sample-and-hold circuits, and many other circuits.
The LF347 and LF347B are characterized for operation from 0°C to 70°C.
symbol (each amplifier)
+
IN
IN + OUT
AVAILABLE OPTIONS
VIOmax
PACKAGE
TA
V
IO
max
AT 25°CSMALL OUTLINE
(D) PLASTIC DIP
(N)
0
°
Cto70
°
C
10 mV LF347D LF347N
0°C
to
70°C
5 mV LF347BD LF347BN
The D packages are available taped and reeled. Add R suffix to the device
type (e.g., LF347DR).
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, VCC + 18 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply voltage, VCC 18 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage, V ID ±30 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage, VI (see Note 1) ±15 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of output short circuit unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating temperature range 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range 65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE 1: Unless otherwise specified, the absolute maximum negative input voltage is equal to the negative power supply voltage.
Copyright 1994, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN
1IN+
VCC+
2IN+
2IN
2OUT
4OUT
4IN
4IN +
VCC
3IN+
3IN
3OUT
D OR N PACKAGE
(TOP VIEW)
LF347, LF347B
JFET-INPUT
QUAD OPERATIONAL AMPLIFIERS
SLOS013B – MARCH 1987 – REVISED AUGUST 1994
2POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DISSIPATION RATING TABLE
PACKAGE TA 25°C
POWER RATING DERATING
FACTOR DERATE
ABOVE TATA = 70°C
POWER RATING
D
N608 mW
680 mW 7.6 mW/°C
N/A 61°C
N/A 608 mW
680 mW
recommended operating conditions
MIN MAX UNIT
Supply voltage, VCC + 3.5 18 V
Supply voltage, VCC 3.5 –18 V
electrical characteristics over operating free-air temperature range, VCC± = ±15 V (unless
otherwise specified)
PARAMETER
TEST
T
LF347 LF347B
UNIT
PARAMETER
CONDITIONS
T
A
MIN TYP MAX MIN TYP MAX
UNIT
VIO
In
p
ut offset voltage
V
IC
= 0, 25°C 5 10 3 5
mV
V
IO
Inp
u
t
offset
v
oltage
IC ,
RS = 10 kFull range 13 7
mV
αVIO Average temperature coef ficient of
input offset voltage VIC = 0,
RS = 10 k18 18 µV/°C
IIO
Inp t offset c rrent
VIC =0
25°C 25 100 25 100 pA
I
IO
I
nput o
ff
set current
V
IC =
0
70°C 4 4 nA
IIB
Inp t bias c rrent
VIC =0
25°C 50 200 50 200 pA
I
IB
I
nput
bi
as current
V
IC =
0
70°C 8 8 nA
VICR Common-mode input voltage range ±11 –12
to
15 ±11 –12
to
15 V
VOM Maximum peak output voltage swing RL = 10 k±12 ±13.5 ±12 ±13.5 V
AVD
Large signal differential voltage
V
O
= ±10 V, 25°C 25 100 50 100
V/mV
A
VD
Large
-
signal
differential
v
oltage
O,
RL = 2 kFull range 15 25
V/mV
riInput resistance TA = 25°C 1012 1012
CMRR Common-mode rejection ratio RS 2 k70 100 80 100 dB
kSVR Supply-voltage rejection ratio See Note 2 70 100 80 100 dB
ICC Supply current 8 11 8 11 mA
Full range is 0°C to 70°C.
Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive. Pulse techniques
must be used that will maintain the junction temperatures as close to the ambient temperature as possible.
NOTE 2: Supply-voltage rejection ratio is measured for both supply magnitudes increasing or decreasing simultaneously.
operating characteristics, VCC±= ±15 V
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
VO1/VO2 Crosstalk attentuation f = 1 kHz 120 dB
SR Slew rate 8 13 V/µs
B1Unity-gain bandwidth 3 MHz
VnEquivalent input noise voltage f = 1 kHz, RS = 20 18 nV/Hz
InEquivalent input noise current f = 1 kHz 0.01 pA/Hz
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
LF347BD ACTIVE SOIC D 14 50 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347BDE4 ACTIVE SOIC D 14 50 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347BDG4 ACTIVE SOIC D 14 50 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347BDR ACTIVE SOIC D 14 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347BDRE4 ACTIVE SOIC D 14 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347BDRG4 ACTIVE SOIC D 14 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347BN ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
LF347BNE4 ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
LF347D ACTIVE SOIC D 14 50 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347DE4 ACTIVE SOIC D 14 50 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347DG4 ACTIVE SOIC D 14 50 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347DR ACTIVE SOIC D 14 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347DRE4 ACTIVE SOIC D 14 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347DRG4 ACTIVE SOIC D 14 2500 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
LF347N ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
LF347NE4 ACTIVE PDIP N 14 25 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
PACKAGE OPTION ADDENDUM
www.ti.com 23-Apr-2007
Addendum-Page 1
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 23-Apr-2007
Addendum-Page 2
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LF347BDR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
LF347DR SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 20-Aug-2011
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LF347BDR SOIC D 14 2500 333.2 345.9 28.6
LF347DR SOIC D 14 2500 333.2 345.9 28.6
PACKAGE MATERIALS INFORMATION
www.ti.com 20-Aug-2011
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated