Product Brief PE42632 Flip Chip SP6T UltraCMOSTM 2.70 V Switch 100 - 3000 MHz, 50 Figure 1. Functional Diagram Features * Three pin CMOS logic control with V1 TX1 CMOS Control/ Driver and ESD V2 V3 TX2 * * * * * * * RX4 RX3 RX1 RX2 Figure 2. Die Top View Product Description GND ANT VDD 12 13 14 1 TX1 V1 11 15 GND 2 GND V2 10 16 GND 3 TX2 V3 9 GND 8 PE42632 Die 7 RX4 6 RX3 integral decoder/driver Low TX insertion loss: 0.55 dB at 900 MHz, 0.60 dB at 1900 MHz TX - RX Isolation of 38 dB at 900 MHz, 31 dB at 1900 MHz Low harmonics: 2fo = -90 dBc and 3fo = -82 dBc 1500 V HBM ESD tolerance all ports 41 dBm P1dB, TX paths No blocking capacitors required RoHS compliant lead-free solder balls 5 4 RX1 RX2 Figure 3. Package Type: Flip Chip Document No. 70-0226-01 www.psemi.com Contact sales@psemi.com for full version of datasheet The PE42632 is a HaRPTM-enhanced SP6T RF Switch developed on the UltraCMOSTM process technology. This 50 switch addresses the specific design needs of the Quad-Band GSM Handset Antenna Switch Module Market. On-chip CMOS decode logic facilitates three-pin low voltage CMOS control. High ESD tolerance of 1500 V at all ports, no blocking capacitor requirements and on-chip SAW filter over-voltage protection devices make this the ultimate in integration and ruggedness. Peregrine's HaRPTM technology enhancements deliver high linearity and exceptional harmonics performance. It is an innovative feature of the UltraCMOSTM process, providing performance superior to GaAs with the economy and integration of conventional CMOS. (c)2007 Peregrine Semiconductor Corp. All rights reserved. Page 1 of 4 PE42632 Product Brief Table 1. Electrical Specifications @ +25 C, VDD = 2.5 - 2.8 V (ZS = ZL = 50 ) Parameter Conditions Operational Frequency Typical Units 100-3000 MHz 0.55 0.6 0.9 1.15 dB dB dB dB Insertion Loss1 ANT - TX - 850 / 900 MHz ANT - TX - 1800 / 1900 MHz ANT - RX - 850 / 900 MHz ANT - RX - 1800 / 1900 MHz Isolation TX - RX - 850 / 900 MHz TX - RX - 1800 / 1900 MHz TX - TX - 850 / 900 MHz TX - TX - 1800 / 1900 MHz 38 31 31 26 dB dB dB dB Return Loss 850 / 900 MHz 1800 / 1900 MHz 23 22 dB 2nd Harmonic2,3 35 dBm TX Input - 850 / 900 MHz 33 dBm TX Input - 1800 / 1900 MHz -90 -89 dBc 3rd Harmonic2,3 35 dBm TX Input - 850 / 900 MHz 33 dBm TX Input - 1800 / 1900 MHz -82 -80 dBc Switching Time4 50% Control Logic to 90% RF 1 s Notes: 1. Insertion loss specified with optimal ANT impedance matching. 2. Measured in Pulsed Wave Mode. 3. Assumes RF input duty cycle of 50% and 4620 s, measured per 3GPP TS 45.005 4. Power on any port must not exceed +20 dBm during switching event. Table 2. Operating Ranges Parameter Temperature range Symbol Min TOP -40 VDD Supply Voltage VDD IDD Power Supply Current (VDD = 2.75 V) IDD TX input power5 (VSWR 3:1) 824-915 MHz TX input power (VSWR 3:1) 1710-1910 MHz 5 RX input power5 (VSWR =1:1) 2.5 Typ Max Units +85 C Symbol VDD Control Voltage Low VIL -0.3 Max Units 4.0 V 2.8 V VI Voltage on any DC input -0.3 13 20 A TST Storage temperature range -65 TOP Operating temperature range -40 +85 dBm PIN (50 ) +33 VIH Power supply voltage Min 2.70 PIN PIN Parameter/Conditions VDD+ 0.3 +150 +35 Control Voltage High Note: Table 3. Absolute Maximum Ratings +20 0.7 x VDD dBm V 0.3 x VDD PIN ( :1) V 5. Assumes RF input period of 4620 s and duty cycle of 50%. VESD Notes: TX input power (50 )6,7 824-915 MHz TX input power (50 )6,7 1710-1910 MHz V C C +38 +36 dBm RX input power (50 )7 +23 TX input power (VSWR = ( :1)6,7 824-915 MHz +35 dBm TX input power (VSWR = ( :1)6,7 1710-1910 MHz +33 dBm 1500 V 100 V ESD Voltage (HBM, MIL_STD 883 Method 3015.7) ESD Voltage (MM, JEDEC, JESD22-A114-B) 6. Assumes RF input period of 4620 s and duty cycle of 50%. 7. V DD within operating range specified in Table 2. Part performance is not guaranteed under these conditions. Exposure to absolute maximum conditions for extended periods of time may adversely affect reliability. Stresses in excess of absolute maximum ratings may cause permanent damage. (c)2007 Peregrine Semiconductor Corp. All rights reserved. Page 2 of 4 Document No. 70-0226-01 UltraCMOSTM RFIC Solutions Contact sales@psemi.com for full version of datasheet PE42632 Product Brief Table 4. Pin Descriptions Figure 4. Pad Configuration (Top View) Pin No. Pin Name Description 1 TX18 RF I/O - TX1 2 GND TX Ground 3 TX28 RF I/O - TX2 4 RX18 RF I/O - RX1 5 RX28 RF I/O - RX2 6 8 RX3 RF I/O - RX3 7 RX48 RF I/O - RX4 8 GND RX Ground GND ANT 9 V3 Switch control input, CMOS logic level 10 V2 Switch control input, CMOS logic level 11 V1 Switch control input, CMOS logic level VDD 12 13 14 1 TX1 V1 11 15 GND 2 GND V2 10 16 GND 3 TX2 V3 9 GND 8 4 RX1 PE42632 Die 7 RX4 6 RX3 5 RX2 Supply 12 VDD 13 GND DC Ground 14 ANT8 RF Common - Antenna 15 GND DC Ground Path V3 V2 V1 16 GND DC Ground ANT - TX1 0 1 1 ANT - TX2 0 0 1 ANT - RX1 1 1 0 ANT - RX2 0 1 0 ANT - RX3 1 0 0 ANT - RX4 0 0 0 Note: Table 5. Truth Table 8. Blocking capacitors needed only when non-zero DC voltage present Electrostatic Discharge (ESD) Precautions When handling this UltraCMOSTM device, observe the same precautions that you would use with other ESD-sensitive devices. Although this device contains circuitry to protect it from damage due to ESD, precautions should be taken to avoid exceeding the specified rating. Latch-Up Avoidance Unlike conventional CMOS devices, UltraCMOSTM devices are immune to latch-up. Table 6. Ordering Information Order Code Description Package Shipping Method PE42632DTI PE42632-DIE-D Bumped Wafer on Film Frame Wafer (Gross Die / Wafer Quantity) PE42632DBI PE42632-DIE-400G Die in Waffle Pack 400 Dice / Waffle Pack EK-42632-01 PE42632-DIE-1H Evaluation Kit 1/ box Document No. 70-0226-01 www.psemi.com Contact sales@psemi.com for full version of datasheet (c)2007 Peregrine Semiconductor Corp. All rights reserved. Page 3 of 4 PE42632 Product Brief Sales Offices The Americas Peregrine Semiconductor Corporation Peregrine Semiconductor, Asia Pacific (APAC) 9380 Carroll Park Drive San Diego, CA 92121 Tel: 858-731-9400 Fax: 858-731-9499 Shanghai, 200040, P.R. China Tel: +86-21-5836-8276 Fax: +86-21-5836-7652 Europe Peregrine Semiconductor Europe Batiment Maine 13-15 rue des Quatre Vents F-92380 Garches, France Tel: +33-1-4741-9173 Fax : +33-1-4741-9173 Space and Defense Products Peregrine Semiconductor, Korea #B-2607, Kolon Tripolis, 210 Geumgok-dong, Bundang-gu, Seongnam-si Gyeonggi-do, 463-943 South Korea Tel: +82-31-728-3939 Fax: +82-31-728-3940 Peregrine Semiconductor K.K., Japan Teikoku Hotel Tower 10B-6 1-1-1 Uchisaiwai-cho, Chiyoda-ku Tokyo 100-0011 Japan Tel: +81-3-3502-5211 Fax: +81-3-3502-5213 Americas: Tel: 858-731-9453 Europe, Asia Pacific: 180 Rue Jean de Guiramand 13852 Aix-En-Provence Cedex 3, France Tel: +33-4-4239-3361 Fax: +33-4-4239-7227 For a list of representatives in your area, please refer to our Web site at: www.psemi.com Data Sheet Identification Advance Information The product is in a formative or design stage. The data sheet contains design target specifications for product development. Specifications and features may change in any manner without notice. Preliminary Specification The data sheet contains preliminary data. Additional data may be added at a later date. Peregrine reserves the right to change specifications at any time without notice in order to supply the best possible product. Product Specification The data sheet contains final data. In the event Peregrine decides to change the specifications, Peregrine will notify customers of the intended changes by issuing a DCN (Document Change Notice). (c)2007 Peregrine Semiconductor Corp. All rights reserved. Page 4 of 4 The information in this data sheet is believed to be reliable. However, Peregrine assumes no liability for the use of this information. Use shall be entirely at the user's own risk. No patent rights or licenses to any circuits described in this data sheet are implied or granted to any third party. Peregrine's products are not designed or intended for use in devices or systems intended for surgical implant, or in other applications intended to support or sustain life, or in any application in which the failure of the Peregrine product could create a situation in which personal injury or death might occur. Peregrine assumes no liability for damages, including consequential or incidental damages, arising out of the use of its products in such applications. The Peregrine name, logo, and UTSi are registered trademarks and UltraCMOS and HaRP are trademarks of Peregrine Semiconductor Corp. Document No. 70-0226-01 UltraCMOSTM RFIC Solutions Contact sales@psemi.com for full version of datasheet