Revised December 2005 FSA266 * NC7WB66 Low Voltage Dual SPST Normally Open Analog Switch or 2-Bit Bus Switch General Description The FSA266 or NC7WB66 is an ultra high-speed (UHS) dual single-pole/single-throw (SPST) analog switch or 2-bit bus switch. The device is fabricated with advanced sub-micron CMOS technology to achieve high speed enable and disable times and low On Resistance over a broad VCC range. The device is specified to operate over the 1.65 to 5.5V VCC operating range. The device is organized as a dual switch with independent CMOS compatible switch enable (OE) controls. When OE is HIGH, the switch is ON and Port A is connected to Port B. When OE is LOW, the switch is OPEN and a high-impedance state exists between the two ports. The enable inputs tolerate voltages up to 5.5V independent of the VCC operating range. Features O Useful in both analog and digital applications O Space saving US8 surface mount package O MicroPak Pb-Free leadless package O Typical 7: On Resistance @ 5V VCC O Broad VCC operating range: 1.65V to 5.5V O Rail-to-Rail signal handling O Power down high impedance control inputs O Control inputs are overvoltage tolerant O Control inputs are CMOS compatible O !300 MHz 3dB bandwidth Ordering Code: Order Number Product Package Code Number Top Mark FSA266K8X MAB08A WB66 FSA266L8X MAC08A P4 NC7WB66K8X MAB08A WB66 NC7WB66L8X MAC08A P4 Package Description Supplied As 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide 3K Units on Tape and Reel Pb-Free 8-Lead MicroPak, 1.6 mm Wide 5K Units on Tape and Reel 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide 3K Units on Tape and Reel Pb-Free 8-Lead MicroPak, 1.6 mm Wide 5K Units on Tape and Reel Pb-Free package per JEDEC J-STD-020B. MicroPak is a trademark of Fairchild Semiconductor Corporation. (c) 2005 Fairchild Semiconductor Corporation DS500373 www.fairchildsemi.com FSA266 * NC7WB66 Low Voltage Dual SPST Normally Open Analog Switch or 2-Bit Bus Switch May 2000 FSA266 * NC7WB66 Logic Symbol Connection Diagrams Pin Assignments for US8 (Top View) Pad Assignments for MicroPak Analog Symbol (Top Through View) Pin Descriptions Pin Names Description A Switch Port A B Switch Port B OE Control Input Function Table Switch Enable Input (OE) Function L Disconnect H B Connected to A H HIGH Logic Level L LOW Logic Level www.fairchildsemi.com 2 Recommended Operating Conditions (Note 3) 0.5V to 7.0V 0.5V to VCC 0.5V 0.5V to 7.0V Supply Voltage (VCC) DC Switch Voltage (VS) DC Input Voltage (VIN) (Note 2) DC Input Diode Current @ (IIK) VIN 0V Supply Voltage (VCC) 50 mA DC VCC or Ground Current (ICC/IGND) Storage Temperature Range (TSTG) Junction Lead Temperature Power Dissipation (PD) @ 85qC SC70-6 0V to VCC 40qC to 85qC Input Rise and Fall Time (tr, tf) Control Input VCC Control Input VCC Control Input VCC 1.65V2.7V 0 ns/V to 20 ns/V 3.0V3.6V 0 ns/V to 10 ns/V 4.5V5.5V 0 ns/V to 5 ns/V Thermal Resistance (TJA) 260qC (Soldering, 10 Seconds) 0V to VCC Operating Temperature (TA) 150qC under Bias (TJ) Junction Lead Temperature (TL) 0V to 5.5V Switch Input Voltage (VIN) Switch Output Voltage (VOUT) r128 mA r100 mA 65qC to 150qC DC Switch Output Current (IOUT) 1.65V to 5.5V Control Input Voltage (VIN) 250qC/W Note 1: The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The "Recommended Operating Conditions" table will define the conditions for actual device operation. 250 mW Note 2: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 3: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics Symbol Parameter VCC TA (V) Min 25qC Typ 40qC to 85qC TA Max Min HIGH Level Input Voltage 1.65 to 1.95 0.75 VCC 2.3 to 5.5 0.7 VCC VIL LOW Level Input Voltage 1.65 to 1.95 0.25 VCC 0.25VCC 2.3 to 5.5 0.3 VCC 0.3 VCC IIN Input Leakage Current IOFF Switch OFF Leakage Current RON Switch On Resistance 6.0 10.0 10.0 7.0 13.5 13.5 6.0 10.0 10.0 7.5 15.0 15.0 8.5 15.0 15.0 9.0 20.0 20.0 10.5 20.0 20.0 12.5 30.0 30.0 17.0 30.0 30.0 (Note 4) 1.65 to 5.5 4.5 2.3 1.65 Quiescent Supply Current All Channels ON or OFF Analog Signal Range RRange 'RON Rflat 5.5 VCC r1.0 r1.0 1.0 0 VCC 0 Conditions V 0.7 VCC r0.1 r0.1 3.0 ICC 0.75 VCC 0 to 5.5 Units Max VIH V PA PA 0 d VIN d 5.5V 0 d A, B d VCC VI 0V, IO VI 2.4V, IO VI 4.5V, IO : VI 0V, IO VI 3V, IO 24 mA : VI 0V, IO 8 mA VI 2.3V, IO VI 0V, IO VI 1.65V, IO : : 10.0 PA VCC V VIN IOUT On Resistance Over 4.5 8.0 15.0 15.0 IO Signal Range 3.0 15.0 30.0 30.0 IO (Note 4)(Note 5) 2.3 45.0 75.0 75.0 1.65 150 275 275 On Resistance Match 4.5 0.2 Between Channels 3.0 0.2 (Note 4)(Note 7) 2.3 0.5 1.65 0.6 : IO IO IO : IO IO IO On Resistance Flatness 4.5 2.5 6.0 6.0 (Note 4)(Note 5)(Note 6) 3.0 8.0 17.5 17.5 IO IO 2.3 33.0 60.0 60.0 IO 1.65 135 250 250 IO 30 mA 30 mA 30 mA 24 mA 8 mA 4 mA 4 mA VCC or GND 0 30 mA, 0 d VI d VCC 24 mA, 0 d VI d VCC 8 mA, 0 d VI d VCC 4 mA, 0 d VI d VCC 30 mA, VI 3.15 24 mA, VI 2.1 8 mA, VI 1.6 4 mA, VI 1.15 30 mA, 0 d VI d VCC 24 mA, 0 d VI d VCC 8 mA, 0 d VI d VCC 4 mA, 0 d VI d VCC Note 4: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A or B) pins. Note 5: Guaranteed by design. Note 6: Flatness is defined as the difference between the minimum and maximum value of ON Resistance over the specified range of conditions. 3 www.fairchildsemi.com FSA266 * NC7WB66 Absolute Maximum Ratings(Note 1) FSA266 * NC7WB66 DC Electrical Characteristics Note 7: 'RON (Continued) RON max RON min measured at identical VCC, temperature and voltage levels. AC Electrical Characteristics Symbol tPHL, tPLH Parameter TA VCC (V) Min tPLZ, tPHZ Q Typ Max 1.0 Propagation Delay Bus-to-Bus 4.5 to 5.5 0.35 (Note 8) 3.0 to 3.6 0.7 1.5 2.3 to 2.7 1.1 2.5 1.65 to 1.95 tPZL, tPZH 40qC to 85qC 2.0 4.0 Output Enable Time 4.5 to 5.5 0.8 2.0 3.2 Turn on Time 3.0 to 3.6 1.2 2.5 3.9 2.3 to 2.7 1.5 3.2 5.6 1.65 to 1.95 2.5 5.7 10.0 Output Disable Time 4.5 to 5.5 0.8 2.6 4.1 Turn Off Time 3.0 to 3.6 1.5 3.4 5.0 2.3 to 2.7 2.0 4.2 6.9 1.65 to 1.95 3.0 6.2 10.5 Charge Injection (Note 9) Units ns ns ns 1.65 to 5.5 pC Conditions VI OPEN CL 50 pF, RU VI 0V for tPZH VI 2 x VCC for tPZL CL 50 pF, RU VI 0V for tPHZ 2 x VCC for tPLZ CL 50 pF, RU CL 0.1 nF, VGEN Off Isolation (Note 10) 1.65 to 5.5 -55.0 dB RL f Xtalk Crosstalk 70.0 1.65 to 5.5 dB RL f BW 3dB Bandwidth THD Total Harmonic Distortion !300 1.65 to 5.5 (Note 9) MHz RL RL 5 .016 % 0 :, f 50 :, CL 500: Figures 1, 2 Figures 1, 2 RD VI RGEN OIRR RD Figure Number 500: Figures 1, 2 RD 500: 0V, Figure 3 1 MHz 5 pF, Figure 4 5 pF, Figure 5 10 MHz 50 :, CL 10 MHz 50 : Figure 8 600: 0.5 VP-P f 600 Hz to 20 KHz Note 8: This parameter is guaranteed by design. The switch contributes no propagation delay other than the RC delay of the On Resistance of the switch and the 50 pF load capacitance. Note 9: Guaranteed by design. Note 10: Off Isolation 20 log10 [VA/VBn] Capacitance Symbol CIN Parameter Control Pin Input Capacitance Typ Max 2.5 Units pF Conditions VCC 0V Figures CI/O (OFF) Switch Port Off Capacitance 5.0 pF VCC 5.0V Figure 6 CI/O (ON) Switch Port Capacitance when Switch is Enabled 10.0 pF VCC 5.0V Figure 7 www.fairchildsemi.com 4 FSA266 * NC7WB66 AC Loading and Waveforms Input driven by 50: source terminated in 50: CL includes load and stray capacitance. Input PRR 1.0 MHz; tw 500 ns FIGURE 1. AC Test Circuit FIGURE 2. AC Waveforms FIGURE 3. Charge Injection Test 5 www.fairchildsemi.com FSA266 * NC7WB66 AC Loading and Waveforms (Continued) FIGURE 4. Off Isolation FIGURE 5. Crosstalk FIGURE 6. Channel Off Capacitance FIGURE 7. Channel On Capacitance FIGURE 8. Bandwidth www.fairchildsemi.com 6 TAPE FORMAT for US8 Package Designator K8X Tape Section Number Cavities Cavity Status Cover Tape Status Leader (Start End) 125 (typ) Empty Sealed Carrier 250 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed Tape Section Number Cavities Cavity Status Cover Tape Status Leader (Start End) 125 (typ) Empty Sealed Carrier 250 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed TAPE DIMENSIONS inches (millimeters) TAPE FORMAT for MicroPak Package Designator L8X TAPE DIMENSIONS inches (millimeters) 7 www.fairchildsemi.com FSA266 * NC7WB66 Tape and Reel Specification FSA266 * NC7WB66 REEL DIMENSIONS inches (millimeters) Tape Size 8 mm www.fairchildsemi.com A B C D N 7.0 0.059 0.512 0.795 2.165 (177.8) (1.50) (13.00) (20.20) (55.00) 8 W1 W2 (8.40 1.50/0.00) (14.40) 0.331 0.059/0.000 0.567 W3 W1 0.078/0.039 (W1 2.00/1.00) FSA266 * NC7WB66 Physical Dimensions inches (millimeters) unless otherwise noted 8-Lead US8, JEDEC MO-187, Variation CA 3.1mm Wide Package Number MAB08A 9 www.fairchildsemi.com FSA266 * NC7WB66 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Pb-Free 8-Lead MicroPak, 1.6 mm Wide Package Number MAC08A www.fairchildsemi.com 10 FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION As used herein: provided in the labeling, can be reasonably expected to result in significant injury to the user. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or 2. A critical component is any component of a life support (b) support or sustain life, or (c) whose failure to perform device or system whose failure to perform can be reasonwhen properly used in accordance with instructions for use ably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. 11 www.fairchildsemi.com FSA266 * NC7WB66 Low Voltage Dual SPST Normally Open Analog Switch or 2-Bit Bus Switch DISCLAIMER