ALUMINUM ELECTROLYTIC CAPACITORS ZS 4.5mmL Chip Type series WX Chip type with 4.5mm height. Designed for surface mounting on high density PC board. Smaller Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). ZS High Te m p e rature ZT ZP Bi-polarized Smaller Specifications ZR Item Performance Characteristics Category Temperature Range - 40 to + 85C Rated Voltage Range 4 to 50V Rated Capacitance Range 0.1 to 220F Capacitance Tolerance + - 20% at 120Hz, 20C After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (A) ,whichever is greater. Leakage Current Tangent of loss angle (tan ) Rated voltage (V) tan (MAX.) 4 0.50 Measurement frequency : 120Hz, Temperature : 20C 10 16 25 35 50 0.24 0.19 0.16 0.14 0.14 6.3 0.30 Measurement frequency : 120Hz 4 7 15 Rated voltage (V) Z- 25C / Z+20C Impedance ratio ZT / Z20 (MAX.) Z- 40C / Z+20C Stability at Low Temperature 6.3 4 8 16 2 4 35 2 3 50 2 3 Within + - 20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 85C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within + 10% of the initial capacitance value - maintained at 250C. The capacitors shall meet the tan Less than or equal to the initial specified value characteristic requirements listed at right when they are Leakage current Less than or equal to the initial specified value removed from the plate and restored to 20C. Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 16V 10F) Chip Type 1 4.5 Voltage mark for 6.3V is C+ - 0.2 3 4 5 6 7 8 9 10 11 12 13 14 Taping code E B+- 0.2 A2 10 16V D+- 0.5 Voltage 2 U Z S 1 C 1 0 0 MC L 1 GB A+- 0.3 A + - 0.3 Plastic platform 0.3 MAX. 0.5 MAX. Positive Capacitance Lot No. 25 2 4 Capacitance change tan Leakage current The specifications listed at right shall be met when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 85C. Endurance 10 3 8 D A B C E 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 (mm) 6.3 2.4 6.6 6.6 2.2 Configuration Capacitance tolerance (+ - 20%) Rated capacitance (10F) Rated voltage (16V) + 0.1 - 0.2 Series name Negative 0.5 to 0.8 6V . Type Dimensions 4 0G V Cap. (F) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 220 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 221 4 4 5 6.3 6.3 0J 28 33 56 96 4 5 5 6.3 10 1A 28 37 45 70 5 5 6.3 16 1C 33 41 52 4 5 6.3 6.3 25 1E 23 37 49 58 4 5 6.3 6.3 35 1V 16 27 42 52 4 5 6.3 50 1H 18 29 46 4 4 4 4 4 4 4 5 6.3 Case size D (mm) 1.0 2.0 2.8 4.0 8.4 13 17 20 33 Rated ripple Rated ripple current (mArms) at 85C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UR(p.104), UG(p.110) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100A