Toggle Switches Sub-Miniature Specifications: Contact rating Mechanical life Maximum contact resistance Minimum insulation resistance Dielectric strength Operating temperature : Dependent upon content material. : 30,000 make and break cycles. : 20 m initial at 2-4 V dc 100 mA for both silver and gold plated contacts. : 1,000 M. : 1,000 V rms at sea level. : -30C to 85C. Materials: Case Actuator Bushing Housing Switch support Terminal / contact Actuator Model No 2 M S Model No 1 T 1 Actuator T1 9.40 high 2MS1 SP On-None-On 2MS2 SP On-None-Mom. T2 5.33 high 2MS3 SP On-Off-On 2MD1 DP On-None-On 2MD3 DP On-Off-On Bushing B : : : : : : Terminations 2 M 2 Diallyl phthalate (DAP). Brass, chrome plated. Brass, nickel plated. Stainless steel. Brass, tin plated. Silver or gold plated. Contact Material R Seal E Bushing Terminations B2 5.59 high, flat (NON-THD) B5 7.87 high, flat (THD) M2 M6 Contact Material Seal R Gold E Epoxy (std) PC thru-hole Right angle, PC thru-hole www.element14.com www.farnell.com www.newark.com Page <1> 06/06/11 V1.1 Toggle Switches Sub-Miniature Switch Function Number of Poles SP Switch Function UL / CSA Model Number Model Number Q2211 2MS1 Q2212 2MS2 Q2213 2MS3 Off Q2221 2MD1 None DP Position 1 Position 2 Position 3 On None On Q2223 2MD3 Connected Terminals / Schematic ON MOM Position 1 Position 2 Position 3 N/A Open ON Off N/A Open MOM = Momentary Pole Options SPDT 2MS6 Models : Omit 2nd terminal DPDT www.element14.com www.farnell.com www.newark.com Page <2> 06/06/11 V1.1 Toggle Switches Sub-Miniature Actuator Options T1 T2 T1, T2, Actuator shown with B2 bushing, subtract 0.09 (2.29) for B5 bushing, subtract 0.04 (1.02) for B5 bushing, add 0.09 (2.29) Std for M2 terminal sub 0.016 (0.04) for M2 terminals sub. 016 (0.04) for M6. Termination Options Bushing Options B2 NON-THD B5 THD M2 Double Pole M6, SPDT SPDT P. C. Mounting www.element14.com www.farnell.com www.newark.com Page <3> 06/06/11 V1.1 Toggle Switches Sub-Miniature M6, DPDT DPDT P. C. Mounting Panel Mounting 1/4 In. Bushing 10-48 Bushing Without Locking Ring Without Std. Locking Ring Without Locking Ring Without Std. Locking Ring Hardware Locking Ring www.element14.com www.farnell.com www.newark.com Page <4> 06/06/11 V1.1 Toggle Switches Sub-Miniature Contact Material Options R Contact Plating Terminal Plating Ratings Gold R = Gold 0.4 Volt - Amperes (VA) maximum at 20 V maximum (AC or DC) Soldering Process: Manual soldering Wave soldering : Use soldering iron of 30 watts, controlled at 350C approximately 5 s while applying solder. : Recommended soldering temperature : 260 5C. : Duration of solder immersion : Maximum 5 s (PCB is 1.6 mm in thickness). Soldering : Vapour phase Important Notice : This data sheet and its contents (the "Information") belong to the members of the Premier Farnell group of companies (the "Group") or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group's liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. (c) Premier Farnell plc 2011. www.element14.com www.farnell.com www.newark.com Page <5> 06/06/11 V1.1