LMC6042 LMC6042 CMOS Dual Micropower Operational Amplifier Literature Number: SNOS611C LMC6042 CMOS Dual Micropower Operational Amplifier General Description Features Ultra-low power consumption and low input-leakage current are the hallmarks of the LMC6042. Providing input currents of only 2 fA typical, the LMC6042 can operate from a single supply, has output swing extending to each supply rail, and an input voltage range that includes ground. The LMC6042 is ideal for use in systems requiring ultra-low power consumption. In addition, the insensitivity to latch-up, high output drive, and output swing to ground without requiring external pull-down resistors make it ideal for singlesupply battery-powered systems. n n n n n Other applications for the LMC6042 include bar code reader amplifiers, magnetic and electric field detectors, and handheld electrometers. This device is built with National's advanced Double-Poly Silicon-Gate CMOS process. Low supply current: 10 A/Amp (typ) Operates from 4.5V to 15V single supply Ultra low input current: 2 fA (typ) Rail-to-rail output swing Input common-mode range includes ground Applications n n n n n n n Battery monitoring and power conditioning Photodiode and infrared detector preamplifier Silicon based transducer systems Hand-held analytic instruments pH probe buffer amplifier Fire and smoke detection systems Charge amplifier for piezoelectric transducers See the LMC6041 for a single, and the LMC6044 for a quad amplifier with these features. Connection Diagram 8-Pin DIP/SO 01113701 Low-Power Two-Op-Amp Instrumental Amplifier 01113713 (c) 2004 National Semiconductor Corporation DS011137 www.national.com LMC6042 CMOS Dual Micropower Operational Amplifier August 2000 LMC6042 Absolute Maximum Ratings (Note 1) Junction Temperature (Note 3) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 4) Differential Input Voltage 500V (V+) + 0.3V, (V-) - 0.3V Voltage at Input/Output Pin Supply Voltage Supply Voltage (V+ - V-) 16V Output Short Circuit to V+ (Note 12) Output Short Circuit to V- (Note 2) Operating Ratings Temperature Range -40C TJ +85C LMC6042AI, LMC6042I Lead Temperature (Soldering, 10 seconds) 260C Current at Output Pin Current at Power Supply Pin Power Dissipation (Note 10) Thermal Resistance (JA), (Note 11) 35 mA Power Dissipation 4.5V V+ 15.5V Supply Voltage 5 mA 18 mA Current at Input Pin Storage Temperature Range 110C (Note 3) -65C to +150C 8-Pin DIP 101C/W 8-Pin SO 165C/W Electrical Characteristics Unless otherwise spec ified, all limits guaranteed for TA = TJ = 25C. Boldface limits apply at the temperature extremes. V+ = 5V, V- = 0V, VCM = 1.5V, VO = V+/2 and RL > 1M unless otherwise specified. Symbol VOS TCVOS Parameter Conditions Input Offset Voltage Typical LMC6042AI LMC6042I Units (Note 5) Limit Limit (Limit) (Note 6) (Note 6) 1 Input Offset Voltage 3 6 mV 3.3 6.3 Max 1.3 V/C Average Drift IB Input Bias Current 0.002 4 4 pA (Max) IOS Input Offset Current 0.001 2 2 pA (Max) RIN Input Resistance CMRR Common Mode 0V VCM 12.0V Rejection Ratio V+ = 15V Positive Power Supply 5V V+ 15V Rejection Ratio VO = 2.5V Negative Power Supply 0V V- -10V Rejection Ratio VO = 2.5V Input Common-Mode V+ = 5V and 15V Voltage Range For CMRR 50 dB +PSRR -PSRR CMR AV Large Signal > 10 RL = 100 k (Note 7) 75 68 62 dB 66 60 Min 68 62 dB 66 60 Min 84 74 dB 83 73 Min -0.4 -0.1 -0.1 V 0 0 Max V+-1.9V V+- 2.3V V+- 2.3V V V+- 2.5V V+- 2.4V Min 400 300 V/mV 300 200 Min 180 90 V/mV 120 70 Min 200 100 V/mV 160 80 Min 100 50 V/mV 60 40 Min 75 94 Sourcing 1000 Voltage Gain Sinking RL = 25 k (Note 7) Sourcing Sinking www.national.com 2 Tera 500 1000 250 (Continued) Unless otherwise spec ified, all limits guaranteed for TA = TJ = 25C. Boldface limits apply at the temperature extremes. V+ = 5V, V- = 0V, VCM = 1.5V, VO = V+/2 and RL > 1M unless otherwise specified. Symbol VO Parameter Output Swing Conditions V+ = 5V Typical LMC6042AI LMC6042I Units (Note 5) Limit Limit (Limit) (Note 6) (Note 6) 4.970 4.940 V 4.950 4.910 Min 0.030 0.060 V 0.050 0.090 Max 4.987 RL = 100 k to V+/2 0.004 V+ = 5V 4.980 RL = 25 k to V+/2 0.010 V+ = 15V 14.970 + RL = 100 k to V /2 0.007 V+ = 15V 14.950 RL = 25 k to V+/2 0.022 ISC Output Current Sourcing, VO = 0V 22 V+ = 5V ISC Output Current V Min 0.080 0.130 V 0.130 0.180 Max 14.920 14.880 V 14.880 14.820 Min 0.030 0.060 V 0.050 0.090 Max 14.900 14.850 V 14.850 14.800 Min 0.100 0.150 V 0.150 0.200 Max 16 13 mA 10 8 Min 13 mA Min 21 16 8 8 Sourcing, VO = 0V 40 15 15 mA 10 10 Min 39 24 21 mA 8 8 Min 20 34 45 A 39 50 Max 44 56 A 51 65 Max Sinking, VO = 13V (Note 12) Supply Current 4.870 4.820 Sinking, VO = 5V V+ = 15V IS 4.920 4.870 Both Amplifiers VO = 1.5V Both Amplifiers 26 V+ = 15V AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TA = TJ = 25C. Boldface limits apply at the temperature extremes. V+ = 5V, V- = 0V, VCM = 1.5V, VO = V+/2 and RL > 1M unless otherwise specified. Symbol Parameter Conditions LMC6042AI LMC6042I Units Limit Limit (Limit) (Note 6) (Note 6) 0.015 0.010 0.010 0.007 SR Slew Rate GBW Gain-Bandwidth Product 100 kHz m Phase Margin 60 Deg dB en in (Note 8) Typ (Note 5) 0.02 Amp-to-Amp Isolation (Note 9) 115 Input-Referred Voltage Noise f = 1 kHz 83 Input-Referred Current Noise f = 1 kHz V/s Min 0.0002 3 www.national.com LMC6042 Electrical Characteristics LMC6042 AC Electrical Characteristics (Continued) Unless otherwise specified, all limits guaranteed for TA = TJ = 25C. Boldface limits apply at the temperature extremes. V+ = 5V, V- = 0V, VCM = 1.5V, VO = V+/2 and RL > 1M unless otherwise specified. Symbol T.H.D. Parameter Total Harmonic Distortion Conditions Typ LMC6042AI LMC6042I Units (Note 5) Limit Limit (Limit) (Note 6) (Note 6) f = 1 kHz, AV = -5 RL = 100 k, VO = 2 VPP 0.01 % 5V Supply Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Conditions indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Applies to both single-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 110C. Output currents in excess of 30 mA over long term may adversely affect reliability. Note 3: The maximum power dissipation is a function of TJ(Max), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(Max) - TA)/JA. Note 4: Human body model, 1.5 k in series with 100 pF. Note 5: Typical values represent the most likely parametric norm. Note 6: All limits are guaranteed at room temperature (standard type face) or at operating temperature extremes (bold face type). Note 7: V+ = 15V, VCM = 7.5V and RL connected to 7.5V. For Sourcing tests, 7.5V VO 11.5V. For Sinking tests, 2.5V VO 7.5V. Note 8: V+ = 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates. Note 9: Input referred V+ = 15V and RL = 100 k connected to V+/2. Each amp excited in turn with 100 Hz to produce VO = 12 VPP. Note 10: For operating at elevated temperatures the device must be derated based on the thermal resistance JA with PD = (TJ - TA)/JA. Note 11: All numbers apply for packages soldered directly into a PC board. Note 12: Do not connect output to V+when V+ is greater than 13V or reliability may be adversely affected. Typical Performance Characteristics VS = 7.5V, TA = 25C unless otherwise specified Offset Voltage vs Temperature of Five Representative Units Supply Current vs Supply Voltage 01113719 www.national.com 01113720 4 (Continued) Input Bias Current vs Input Common-Mode Voltage Input Bias Current vs Temperature 01113721 01113722 Input Bias Current Voltage Range vs Temperature Output Characteristics Current Sinking 01113723 01113724 Output Characteristics Current Sourcing Input Voltage Noise vs Frequency 01113725 01113726 5 www.national.com LMC6042 Typical Performance Characteristics VS = 7.5V, TA = 25C unless otherwise specified LMC6042 Typical Performance Characteristics VS = 7.5V, TA = 25C unless otherwise specified Crosstalk Rejection vs Frequency CMRR vs Frequency 01113728 01113727 Power Supply Rejection Ratio vs Frequency CMRR vs Temperature 01113729 01113730 Open-Loop Voltage Gain vs Temperature Open-Loop Frequency Response 01113732 01113731 www.national.com (Continued) 6 Gain and Phase Responses vs Load Capacitance (Continued) Gain and Phase Response vs Temperature 01113733 01113734 Common-Mode Error vs Common-Mode Voltage of 3 Representative Units Gain Error (VOS vs VOUT) 01113736 01113735 Non-Inverting Slew Rate vs Temperature Inverting Slew Rate vs Temperature 01113737 01113738 7 www.national.com LMC6042 Typical Performance Characteristics VS = 7.5V, TA = 25C unless otherwise specified LMC6042 Typical Performance Characteristics VS = 7.5V, TA = 25C unless otherwise specified Non-Inverting Large Signal Pulse Response (AV = +1) Non-Inverting Small Signal Pulse Response 01113739 01113740 Inverting Large-Signal Pulse Response Inverting Small Signal Pulse Response 01113741 01113742 Stability vs Capacitive Load Stability vs Capacitive Load 01113743 www.national.com (Continued) 01113744 8 AMPLIFIER TOPOLOGY The LMC6042 incorporates a novel op-amp design topology that enables it to maintain rail-to-rail output swing even when driving a large load. Instead of relying on a push-pull unity gain output buffer stage, the output stage is taken directly from the internal integrator, which provides both low output impedance and large gain. Special feed-forward compensation design techniques are incorporated to maintain stability over a wider range of operating conditions than traditional micropower op-amps. These features make the LMC6042 both easier to design with, and provide higher speed than products typically found in this ultra-low power class. COMPENSATING FOR INPUT CAPACITANCE It is quite common to use large values of feedback resistance with amplifiers with ultra-low input curent, like the LMC6042. Although the LMC6042 is highly stable over a wide range of operating conditions, certain precautions must be met to achieve the desired pulse response when a large feedback resistor is used. Large feedback resistors and even small values of input capacitance, due to transducers, photodiodes, and circuit board parasitics, reduce phase margins. When high input impedances are demanded, guarding of the LMC6042 is suggested. Guarding input lines will not only reduce leakage, but lowers stray input capacitance as well. (See Printed-Circuit-Board Layout for High Impedance Work). 01113706 FIGURE 2. LMC6042 Noninverting Gain of 10 Amplifier, Compensated to Handle Capacitive Loads In the circuit of Figure 2, R1 and C1 serve to counteract the loss of phase margin by feeding the high frequency component of the output signal back to the amplifier's inverting input, thereby preserving phase margin in the overall feedback loop. Capacitive load driving capability is enhanced by using a pull up resistor to V+ (Figure 3). Typically a pull up resistor conducting 10 A or more will significantly improve capacitive load responses. The value of the pull up resistor must be determined based on the current sinking capability of the amplifier with respect to the desired output swing. Open loop gain of the amplifier can also be affected by the pull up resistor (see Electrical Characteristics). 01113705 FIGURE 1. Cancelling the Effect of Input Capacitance The effect of input capacitance can be compensated for by adding a capacitor. Place a capacitor, Cf, around the feedback resistor (as in Figure 1 ) such that: 01113718 FIGURE 3. Compensating for Large Capacitive Loads with a Pull Up Resistor or R1 CIN R2 Cf Since it is often difficult to know the exact value of CIN, Cf can be experimentally adjusted so that the desired pulse response is achieved. Refer to the LMC660 and the LMC662 for a more detailed discussion on compensating for input capacitance. PRINTED-CIRCUIT-BOARD LAYOUT FOR HIGH-IMPEDANCE WORK It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires special layout of the PC board. When one wishes to take advantage of the ultra-low bias current of the LMC6042, typically less than 2 fA, it is essential to have an excellent layout. Fortunately, the techniques of obtaining low leakages are quite 9 www.national.com LMC6042 CAPACITIVE LOAD TOLERANCE Direct capacitive loading will reduce the phase margin of many op-amps. A pole in the feedback loop is created by the combination of the op-amp's output impedance and the capacitive load. This pole induces phase lag at the unity-gain crossover frequency of the amplifier resulting in either an oscillatory or underdamped pulse response. With a few external components, op amps can easily indirectly drive capacitive loads, as shown in Figure 2. Applications Hints LMC6042 Applications Hints (Continued) simple. First, the user must not ignore the surface leakage of the PC board, even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or contamination, the surface leakage will be appreciable. To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LMC6042's inputs and the terminals of capacitors, diodes, conductors, resistors, relay terminals etc. connected to the op-amp's inputs, as in Figure 4. To have a significant effect, guard rings should be placed on both the top and bottom of the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifier inputs, since no leakage current can flow between two points at the same potential. For example, a PC board trace-to-pad resistance of 1012, which is normally considered a very large resistance, could leak 5 pA if the trace were a 5V bus adjacent to the pad of the input. This would cause a 100 times degradation from the LMC6042's actual performance. However, if a guard ring is held within 5 mV of the inputs, then even a resistance of 1011 would cause only 0.05 pA of leakage current. See Figure 5 for typical connections of guard rings for standard op-amp configurations. 01113708 Inverting Amplifier 01113710 Non-Inverting Amplifier 01113709 Follower FIGURE 5. Typical Connections of Guard Rings 01113707 FIGURE 4. Example of Guard Ring in P.C. Board Layout www.national.com 10 the differential gain will be in the range of 10 to 1000. This two op-amp instrumentation amplifier features an independent adjustment of the gain and common-mode rejection trim, and a total quiescent supply current of less than 20 A. To maintain ultra-high input impedance, it is advisable to use ground rings and consider PC board layout an important part of the overall system design (see Printed-Circuit-Board Layout for High Impedance Work). Referring to Figure 7, the input voltages are represented as a common-mode input VCM plus a differential input VD. (Continued) The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few circuits, there is another technique which is even better than a guard ring on a PC board: Don't insert the amplifier's input pin into the board at all, but bend it up in the air and use only air as an insulator. Air is an excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 6. Rejection of the common-mode component of the input is accomplished by making the ratio of R1/R2 equal to R3/R4. So that where, A suggested design guideline is to minimize the difference of value between R1 through R4. This will often result in improved resistor tempco, amplifier gain, and CMRR over temperature. If RN = R1 = R2 = R3 = R4 then the gain equation can be simplified: 01113711 (Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board.) FIGURE 6. Air Wiring Due to the "zero-in, zero-out" performance of the LMC6042, and output swing rail-rail, the dynamic range is only limited to the input common-mode range of 0V to VS - 2.3V, worst case at room temperature. This feature of the LMC6042 makes it an ideal choice for low-power instrumentation systems. A complete instrumentation amplifier designed for a gain of 100 is shown in Figure 8. Provisions have been made for low sensitivity trimming of CMRR and gain. Typical Single-Supply Applications (V+ = 5.0 VDC) The extremely high input impedance, and low power consumption, of the LMC6042 make it ideal for applications that require battery-powered instrumentation amplifiers. Examples of these types of applications are hand-held pH probes, analytic medical instruments, magnetic field detectors, gas detectors, and silicon based pressure transducers. The circuit in Figure 7 is recommended for applications where the common-mode input range is relatively low and 01113712 FIGURE 7. Two Op-Amp Instrumentation Amplifier 11 www.national.com LMC6042 Applications Hints LMC6042 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) 01113713 FIGURE 8. Low-Power Two-Op-Amp Instrumentation Amplifier 01113714 FIGURE 9. Low-Leakage Sample and Hold 01113715 FIGURE 10. Instrumentation Amplifier www.national.com 12 LMC6042 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) 01113716 FIGURE 11. 1 Hz Square Wave Oscillator 01113717 FIGURE 12. AC Coupled Power Amplifier Ordering Information Temperature Package Range NSC Industrial Drawing Transport Media -40C to +85C 8-Pin LMC6042AIM, LMC6042AIMX Small Outline LMC6042IM, LMC6042IMX 8-Pin LMC6042AIN Molded DIP LMC6042IN M08A N08E 13 Rail Tape and Reel Rail www.national.com LMC6042 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin Small Outline Package Order Number LMC6042AIM, LMC6042AIMX, LMC6042IM or LMC6042IMX NS Package Number M08A 8-Pin Molded Dual-In-Line Package Order Number LMC6042AIN or LMC6042IN NS Package Number N08E www.national.com 14 LMC6042 CMOS Dual Micropower Operational Amplifier Notes National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated