Philips Semiconductors Linear Products Product specification Quad timer NE558 DESCRIPTION PIN CONFIGURATION The 558 Quad Timers are monolithic timing devices which can be used to produce four independent timing functions. The 558 output sinks current. These highly stable, general purpose controllers can be used in a monostable mode to produce accurate time delays; from microseconds to hours. In the time delay mode of operation, the time is precisely controlled by one external resistor and one capacitor. A stable operation can be achieved by using two of the four timer sections. D1, N Packages OUTPUT A 1 TIMING A 2 TRIGGER A 3 CONTROL VOLTAGE 4 OUTPUT STAGE OUTPUT STAGE ff ff 15 VR The four timer sections in the 558 are edge-triggered; therefore, when connected in tandem for sequential timing applications, no coupling capacitors are required. Output current capability of 100mA is provided in both devices. VCC FEATURES * 100mA output current per section * Edge-triggered (no coupling capacitor) * Output independent of trigger conditions * Wide supply voltage range 4.5V to 16V * Timer intervals from microseconds to hours * Time period equals RC * Military qualifications pending TRIGGER B 14 TRIGGER D VR 13 RESET 12 GROUND R1 R2 COMP COMP 7 8 11 TRIGGER C 10 TIMING C VR ff OUTPUT TIMING D COMP 5 6 OUTPUT D VR COMP VR OUTPUT 16 ff OUTPUT STAGE OUTPUT STAGE 9 OUTPUT C TOP VIEW NOTE: 1. SOL released in large SO package only. APPLICATIONS * Sequential timing * Time delay generation * Precision timing * Industrial controls * Quad one-shot ORDERING INFORMATION TEMPERATURE RANGE ORDER CODE 16-Pin Plastic Small Outline Large (SOL) Package DESCRIPTION 0 to +70C NE558D DWG # 0171B 16-Pin Plastic Dual In-Line Package (DIP) 0 to +70C NE558N 0406C ABSOLUTE MAXIMUM RATINGS SYMBOL PARAMETER VCC Supply voltage PD Maximum power dissipation TA=25C ambient (still-air)1 N package D package TA Operating ambient temperature range TSTG Storage temperature range TSOLD Lead soldering temperature (10sec max) RATING UNIT +16 V 1450 mW 1090 mW 0 to +70 C -65 to +150 C +300 C NOTES: 1. Derate above 25C, at the following rates: N package at 11.6mW/C D package at 8.7mW/C August 31, 1994 378 853-0150 13721 Philips Semiconductors Linear Products Product specification Quad timer NE558 DC AND AC ELECTRICAL CHARACTERISTICS TA = 25C, VCC = +5V to +15V, unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS VCC Supply voltage ICC Supply current VCC=Reset=15V Timing accuracy (t=RC) R=2k to 100k, NE558 Min Typ 4.5 16 Max UNIT 16 V 36 mA C=1F tA Initial accuracy 2 5 % tA/T Drift with temperature 30 150 ppm/C tA/VS Drift with supply voltage 0.1 0.9 %/V VTRIG Trigger voltage1 VCC=15V ITRIG Trigger current Trigger=0V VRESET Reset voltage2 IRESET Reset current VTH Threshold voltage 0.63 Threshold leakage 15 VOUT 0.8 2.4 V 5 100 A 2.4 V 50 500 A 0.8 Reset Output voltage3 xVCC nA IL=10mA 0.1 IL=100mA 1.0 2.0 V 10 500 nA Output leakage 0.4 V tPD Propagation delay 1.0 s tR Rise time of output IL=100mA 100 ns tF Fall time of output IL=100mA 100 ns NOTES: 1. The trigger functions only on the falling edge of the trigger pulse only after previously being high. After reset, the trigger must be brought high and then low to implement triggering. 2. For reset below 0.8V, outputs set low and trigger inhibited. For reset above 2.4V, trigger enabled. 3. The 558 output structure is open-collector which requires a pull-up resistor to VCC to sink current. The output is normally low sinking current. August 31, 1994 379 Philips Semiconductors Linear Products Product specification Quad timer NE558 558 EQUIVALENT CIRCUIT VCC RESET TIMING + 3V VCONTROL TRIGGER OUT GND VCC TRIGGER R1 RL R1 R1 RL R1 RL RL OUTPUT 1 T T C1 TRIGGER TR 0 T C1 TR 0 T C1 TR 0 C2 TR 0 OUTPUT 2 OUTPUT 4 OUTPUT 3 TDELA OUTPUT 1 OUTPUT 2 OUTPUT 3 OUTPUT 4 TDELAY 3(R1C) TOUT R2C2) NOT USED Figure 1. Long-Time Delay August 31, 1994 Y 380 TOUTPUT Philips Semiconductors Linear Products Product specification Quad timer NE558 VCC R1 RL 2 5 START RESET R1 RL C1 3 10 TIME 1 TRIG 0 1 13 C1 7 TIME R1 RL 6 8 11 TRIG 0 2 13 15 VCC START RESET T = RC 02 03 04 b. Expected Waveforms Figure 2. 381 C1 TIME 9 TRIG 0 3 13 a. Ring Counter August 31, 1994 C1 TIME 10K 01 R1 RL 14 16 TRIG 0 4 13 12