LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 LMH6733 Single Supply, 1.0 GHz, Triple Operational Amplifier Check for Samples: LMH6733 FEATURES DESCRIPTION * * * The LMH6733 is a triple, wideband, operational amplifier designed specifically for use where high speed and low power are required. Input voltage range and output voltage swing are optimized for operation on supplies as low as 3V and up to 6V. Benefiting from TI's current feedback architecture, the LMH6733 offers a gain range of 1 to 10 while providing stable operation without external compensation, even at unity gain. These amplifiers provide 650 MHz small signal bandwidth at a gain of 2 V/V , a low 2.1 nV/Hz input referred noise and only consume 5.5 mA (per amplifier) from a single 5V supply. 1 2 * * * * * * Supply Range 3 to 12V Single Supply Supply Range 1.5V to 6V Split Supply 1.0 GHz -3 dB Small Signal Bandwidth - (AV = +1, VS = 5V) 650 MHz -3 dB Small Signal Bandwidth - (AV = +2, VS = 5V) Low Supply Current (5.5 mA per op Amp, VS = 5V) 2.1 nV/Hz Input Noise Voltage 3750 V/s Slew Rate 70 mA Linear Output Current CMIR and Output Swing to 1V from Each Supply Rail APPLICATIONS * * * * * * * * * HDTV Component Video Driver High Resolution Projectors Flash A/D Driver D/A Transimpedance Buffer Wide Dynamic Range IF Amp Radar/Communication Receivers DDS Post-Amps Wideband Inverting Summer Line Driver The LMH6733 is offered in a 16-Pin SSOP package with flow through pinout for ease of layout and is also pin compatible with the LMH6738. Each amplifier has an individual shutdown pin. Connection Diagram Top View -IN A 1 +IN A 2 DIS B 3 -IN B 4 +IN B 5 DIS C 6 -IN C 7 +IN C 8 16 + DIS A 15 +VS 14 OUT A + 13 -VS 12 OUT B 11 +VS + 10 OUT C 9 -VS Figure 1. 16-Pin SSOP Package See Package Number DBQ0016A 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007-2013, Texas Instruments Incorporated LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings ESD Tolerance (1) (2) (3) Human Body Model 2000V Machine Model 200V + - Supply Voltage (V - V ) 13.2V (4) IOUT Common Mode Input Voltage VCC Maximum Junction Temperature +150C -65C to +150C Storage Temperature Range Soldering Information Infrared or Convection (20 sec.) 235C Wave Soldering (10 sec.) 260C -65C to +150C Storage Temperature Range (1) (2) (3) (4) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications, see the Electrical Characteristics tables. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). The maximum output current (IOUT) is determined by device power dissipation limitations. See the Power Dissipation section of the Applications Information for more details. Operating Ratings (1) Thermal Resistance Package 16-Pin SSOP Temperature Range + (2) - Supply Voltage (V - V ) (1) (2) (JC) (JA) 36C/W 120C/W -40C +85C 3V to 12V Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications, see the Electrical Characteristics tables. The maximum power dissipation is a function of TJ(MAX), JA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ JA. All numbers apply for packages soldered directly onto a PC Board. 5V Electrical Characteristics (1) AV = +2, VCC = 5V, RL = 100, RF = 340; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Performance UGBW -3 dB Bandwidth Unity Gain, VOUT = 200 mVPP 870 SSBW -3 dB Bandwidth VOUT = 200 mVPP, RL = 100 650 SSBW VOUT = 200 mVPP, RL = 150 685 LSBW VOUT = 2 VPP 480 VOUT = 200 mVPP 320 0.1 dB BW (1) 2 0.1 dB Gain Flatness MHz MHz MHz Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 5V Electrical Characteristics (1) (continued) AV = +2, VCC = 5V, RL = 100, RF = 340; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units Time Domain Response TRS Rise and Fall Time (10% to 90%) 2V Step 0.8 ns SR Slew Rate 2V Step 1900 V/s ts Settling Time to 0.1% 2V Step 10 ns te Enable Time From Disable = Rising Edge 10 ns td Disable Time From Disable = Falling Edge 15 ns HD2L 2nd Harmonic Distortion 2 VPP, 10 MHz -63 dBc HD3L 3rd Harmonic Distortion 2 VPP, 10 MHz -73 dBc Distortion Equivalent Input Noise VN Non-Inverting Voltage >10 MHz 2.1 nV/Hz ICN Inverting Current >10 MHz 18.6 pA/Hz NCN Non-Inverting Current >10 MHz 26.9 pA/Hz Video Performance DG Differential Gain 4.43 MHz, RL = 150 0.03 % DP Differential Phase 4.43 MHz, RL = 150 0.025 deg Static, DC Performance (2) VIO Input Offset Voltage IBN Input Bias Current (2) IBI Input Bias Current (2) PSRR Power Supply Rejection Ratio Non-Inverting 2 Inverting (2) CMRR Common Mode Rejection Ratio XTLK Crosstalk ICC Supply Current 2.0 2.5 mV 16.7 28 32 A 1.0 17 19 A +PSRR 59 59 61 -PSRR 58 57 61 52 51.5 54.5 (2) (2) 0.4 Input Referred, f = 10 MHz, Drive Channels A,C Measure Channel B -80 dB dB dB All Three Amps Enabled, No Load 16.7 18 mA Supply Current Disabled V+ RL = 1.54 1.8 mA Supply Current Disabled V- RL = 0.75 1.8 mA Miscellaneous Performance RIN+ Non-Inverting Input Resistance CIN+ Non-Inverting Input Capacitance RIN- Inverting Input Impedance Output Impedance of Input Buffer. RO Output Impedance DC VO Output Voltage Range (2) 27 0.05 RL = 1.11-3.89 1.15-3.85 1.03-3.97 1.1-3.9 1.2-3.8 1.0-4.0 50 60 CMRR > 40 dB IO Linear Output Current VIN = 0V, VOUT < 42 mV (2) (3) pF 1.25-3.75 1.3-3.7 Common Mode Input Range (3) (2) k 1 RL = 100 CMIR (2) 200 1.12-3.88 V V mA Parameter 100% production tested at 25 C. The maximum output current (IOUT) is determined by device power dissipation limitations. See the Power Dissipation section of the Applications Information for more details. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 3 LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com 5V Electrical Characteristics (1) (continued) AV = +2, VCC = 5V, RL = 100, RF = 340; unless otherwise specified. Symbol Parameter Conditions (4) Min Typ Max Units ISC Short Circuit Current VIN = 2V Output Shorted to Ground 170 mA IIH Disable Pin Bias Current High Disable Pin = V+ -72 A IIL Disable Pin Bias Current Low Disable Pin = 0V -360 A VDMAX Voltage for Disable Disable Pin VDMAX 3.2 V VDMIM Voltage for Enable Disable Pin VDMIN 3.6 V (4) Short circuit current should be limited in duration to no more than 10 seconds. See the Power Dissipation section of the Application Section for more details. 5V Electrical Characteristics (1) AV = +2, VCC = 5V, RL = 100, RF = 383; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units Frequency Domain Performance UGBW -3 dB Bandwidth Unity Gain, VOUT = 200 mVPP 1000 SSBW -3 dB Bandwidth MHz VOUT = 200 mVPP, RL = 100 830 SSBW VOUT = 200 mVPP, RL = 150 950 LSBW VOUT = 2 VPP 600 0.1 dB BW 0.1 dB Gain Flatness VOUT = 200 mVPP 350 Rise and Fall Time (10% to 90%) 2V Step 0.7 5V Step 0.8 SR Slew Rate 4V Step 3750 V/s ts Settling Time to 0.1% 2V Step 10 ns te Enable Time From Disable = Rising Edge 10 ns td Disable Time From Disable = Falling Edge 15 ns 2nd Harmonic Distortion 2 VPP, 10 MHz -72 dBc 2 VPP, 10 MHz -63 dBc MHz MHz Time Domain Response TRS TRL ns Distortion HD2L HD3L rd 3 Harmonic Distortion Equivalent Input Noise VN Non-Inverting Voltage >10 MHz 2.1 nV/Hz ICN Inverting Current >10 MHz 18.6 pA/Hz NCN Non-Inverting Current >10 MHz 26.9 pA/Hz Video Performance DG Differential Gain 4.43 MHz, RL = 150 0.03 % DP Differential Phase 4.43 MHz, RL = 150 0.03 Deg Static, DC Performance (2) VIO Input Offset Voltage IBN Input Bias Current (2) IBI Input Bias Current (2) PSRR Power Supply Rejection Ratio CMRR (1) (2) 4 Non-Inverting Inverting (2) Common Mode Rejection Ratio -14 -19 0.6 2.2 2.5 mV 3.5 19 24 A 5 23 26 A +PSRR 59 61.5 -PSRR 58 61 53 52.5 55 (2) dB dB Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Parameter 100% production tested at 25 C. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 5V Electrical Characteristics (1) (continued) AV = +2, VCC = 5V, RL = 100, RF = 383; unless otherwise specified. Symbol Parameter Conditions Min Typ Max Units Input Referred, f = 10 MHz, Drive Channels A,C Measure Channel B -80 All Three Amps Enabled, No Load 19.5 20.8 22.0 mA Supply Current Disabled V+ RL = 1.54 1.8 mA Supply Current Disabled V- RL = 0.75 1.8 mA XTLK Crosstalk ICC Supply Current (2) dB Miscellaneous Performance RIN+ Non-Inverting Input Resistance CIN+ Non-Inverting Input Capacitance RIN- Inverting Input Impedance Output Impedance of Input Buffer RO Output Impedance DC VO Output Voltage Range (2) 200 k 1 pF 30 0.05 RL = 100 3.55 3.5 3.7 RL = 3.85 4.0 3.9 3.8 4.0 V 70 80 mA V CMIR Common Mode Input Range CMRR > 43 dB IO Linear Output Current VIN = 0V, VOUT < 42 mV ISC Short Circuit Current VIN = 2V Output Shorted to Ground 237 mA IIH Disable Pin Bias Current High Disable Pin = V+ -72 A IIL Disable Pin Bias Current Low Disable Pin = 0V -360 A VDMAX Voltage for Disable Disable Pin VDMAX 3.2 V VDMIM Voltage for Enable Disable Pin VDMIN 3.6 V (3) (4) (2) (3) (2) (4) The maximum output current (IOUT) is determined by device power dissipation limitations. See the Power Dissipation section of the Applications Information for more details. Short circuit current should be limited in duration to no more than 10 seconds. See the Power Dissipation section of the Application Section for more details. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 5 LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics AV = +2, VCC = 5V, RL = 100, RF = 340; unless otherwise specified). Large Signal Frequency Response 1 0 0 -1 AV = 2, RF = 340: -2 -3 -4 AV = 5, RF = 340: -5 -1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) Large Signal Frequency Response 1 AV = 1, RF = 324: -6 -7 AV = -1, RF = 340: -2 -3 AV = -2, RF = 340: -4 AV = -5, RF = 340: -5 -6 -7 -8 -8 VOUT = 2 VPP -9 -9 10 100 VOUT = 2 VPP 10 1000 100 FREQUENCY (MHz) Figure 2. Figure 3. Frequency Response vs. VOUT 1 1 0 0 -1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) Small Signal Frequency Response 2 -1 AV = 1, RF = 324: -2 -3 AV = 2, RF = 340: -4 -5 AV = 5, RF = 340: -6 -9 -3 VOUT = 0.5 VPP -5 -6 -7 -8 100 VOUT = 2 VPP -4 VOUT = 0.25 VPP 10 VOUT = 1 VPP -2 -7 -8 AV = 2 V/V RF = 340: -9 1000 10 100 FREQUENCY (MHz) Figure 5. Frequency Response vs. Supply Voltage Gain Flatness 0.5 1 VS = 6V -1 VS = 4.3V -2 -3 VS = 4.5V -4 0.4 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 0 -5 -6 AV = 1, RF = 324: 0.3 0.2 AV = 2, RF = 340: 0.1 0 -0.1 -0.2 AV = 5, RF = 340: -0.3 -7 -0.4 -8 VOUT = 2 VPP 10 6 1000 FREQUENCY (MHz) Figure 4. -9 1000 FREQUENCY (MHz) -0.5 100 1000 VOUT = 1 VPP 10 100 FREQUENCY (MHz) FREQUENCY (MHz) Figure 6. Figure 7. Submit Documentation Feedback 1000 Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 Typical Performance Characteristics (continued) AV = +2, VCC = 5V, RL = 100, RF = 340; unless otherwise specified). Pulse Response Crosstalk vs. Frequency 1.2 -10 0.8 CH A & C VOUT = 1 VPP -20 MEASURE CH B CROSSTALK (dBc) -30 VOUT (V) 0.4 0 -0.4 -50 -60 -70 AV = 2V/V -0.8 -1.2 -40 -80 VOUT = 2.0 VPP 0 5 -90 1 10 15 20 25 30 35 40 45 50 10 Figure 8. Distortion vs. Frequency Distortion vs. Output Voltage -10 VOUT = 2 VPP RL = 100: -20 DISTORTION (dBc) -50 -60 HD2 -70 HD3 -80 f = 10 MHz -30 HD3 -40 -50 -60 HD2 -70 -90 -100 -80 -90 1 10 FREQUENCY (MHz) 100 0 1 2 3 VOUT (VPP) 4 5 Figure 10. Figure 11. Small Signal Frequency Response vs. RL Frequency Response vs. Capacitive Load 1 4 VOUT = 1 VPP 3 CL || 1 k: 2 -1 RL = 1 k: 1 0 RL = 150: -1 -2 GAIN (dB) NORMALIZED GAIN (dB) 1000 Figure 9. -40 DISTORTION (dBc) 100 FREQUENCY (MHz) TIME (ns) RL = 100: -3 -5 CL = 100 pF, RS = 17: CL = 47 pF, RS = 23: CL = 33 pF, RS = 26: -4 -5 -3 -7 CL = 15 pF, RS = 38: VOUT = 0.2 VPP -6 10 100 1000 10000 CL = 4.7 pF, RS = 75: -9 100 10 FREQUENCY (MHz) FREQUENCY (MHz) Figure 12. Figure 13. 1000 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 7 LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) AV = +2, VCC = 5V, RL = 100, RF = 340; unless otherwise specified). Series Output Resistance vs. Capacitive Load PSRR vs. Frequency 70 -70 -60 50 -50 PSRR (dB) RECOMMENDED RS (:) LOAD = 1 k: || CL 60 40 30 -30 -20 10 -10 20 40 60 80 100 +PSRR -40 20 0 0 -PSRR 0 0.1 120 CAPACITIVE LOAD (pF) 1 10 100 1000 FREQUENCY (MHz) Figure 14. Figure 15. CMRR vs. Frequency Closed Loop Output Impedance |Z| -50 10 AV = 2 V/V -45 VIN = 0 VPP -40 1 -30 |Z| (:) PSRR (dB) -35 -25 -20 0.1 -15 -10 -5 0 0.1 1 10 100 0.01 0.1 1000 FREQUENCY (MHz) 1 10 Figure 16. Disable Timing 0.6 VIN = 2 VPP 0.2 -60 -70 DISABLE (V) 0.0 -50 OUTPUT (V) CROSSTALK (dBc) VOUT 0.4 -40 VS = 2.5V -0.2 -0.4 -0.6 -80 2 1 -90 -100 0.1 DISABLE 1 10 100 1000 0 10 20 30 40 50 0 60 70 80 90 TIME (ns) FREQUENCY (MHz) Figure 18. 8 1000 Figure 17. Disabled Channel Isolation vs. Frequency -30 100 FREQUENCY (MHz) Figure 19. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 Typical Performance Characteristics (continued) AV = +2, VCC = 5V, RL = 100, RF = 340; unless otherwise specified). DC Errors vs. Temperature 11 100 9 0.7 VOS 0.65 7 0.6 5 0.55 3 0.5 1 0.45 0.4 -40 -20 IBI 0 20 40 60 80 MAGNITUDE 90 80 70 0 60 50 -45 PHASE 40 -1 30 -3 20 0.1 100 120 PHASE () OFFSET VOLTAGE (mV) 110 MAGNITUDE, |Z| (dB :) IBN 0.75 Open Loop Transimpedance 13 BIAS CURRENT (PA) 0.8 -90 -135 1 10 100 -180 1000 FREQUENCY (MHz) TEMPERATURE (C) Figure 20. Figure 21. 120 7 105 6 90 5 75 4 NON-INVERTING VOLTAGE 60 3 NON-INVERTING CURRENT 45 2 30 1 CURRENT NOISE (pA/ Hz) VOLTAGE NOISE (nV/ Hz) Input Noise vs. Frequency 8 15 INVERTING CURRENT 0 0.0001 0.001 0.01 0.1 1 10 0 100 FREQUENCY (MHz) Figure 22. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 9 LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics AV = +2, VCC = 5V, RL = 100, RF = 383; unless otherwise specified). Large Signal Frequency Response Large Signal Frequency Response 3 1 AV = 1, RF = 324: 2 0 -1 AV = 5, RF = 383: -2 -3 AV = 10, RF = 383: -4 -1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 1 -5 -6 AV = -2, RF = 383: -2 -3 AV = -5, RF = 383: -4 -5 AV = -10, RF = 383: -6 -7 -7 -8 VOUT = 2 VPP -9 10 AV = -1, RF = 383: 0 AV = 2, RF = 383: -8 100 VOUT = 2 VPP -9 10 1000 FREQUENCY (MHz) 100 Figure 23. Figure 24. Small Signal Frequency Response Frequency Response vs. VOUT 1 4 3 AV = 1, RF = 324: 0 1 0 -1 -3 -4 AV = 2, RF = 383: -5 -6 -1 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 2 -2 AV = 5, RF = 383: -7 -8 VOUT = 0.25 VPP -9 1000 10 100 FREQUENCY (MHz) AV = 4 VPP -2 -3 AV = 2 VPP -4 AV = 1 VPP -6 -7 -8 AV = 2 V/V RF = 383: -9 10 100 10000 Gain Flatness 0.5 0 0.4 -1 0.3 NORMALIZED GAIN (dB) NORMALIZED GAIN (dB) 10000 Figure 26. 1 VS = 7V -2 -3 VS = 9V -4 -5 VS = 12.5V -6 AV = 1, RF = 324: 0.2 AV = 2, RF = 383: 0.1 0 -0.1 AV = 5, RF = 383: -0.2 -0.3 -7 -9 10 1000 FREQUENCY (MHz) Frequency Response vs. Supply Voltage -8 AV = 0.5 VPP -5 Figure 25. 10 1000 FREQUENCY (MHz) -0.4 VOUT = 2 VPP 100 VOUT = 1 VPP -0.5 1000 1 10 100 FREQUENCY (MHz) FREQUENCY (MHz) Figure 27. Figure 28. Submit Documentation Feedback 1000 Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 Typical Performance Characteristics (continued) AV = +2, VCC = 5V, RL = 100, RF = 383; unless otherwise specified). Pulse Response Crosstalk vs. Frequency -10 1.2 CH A & C VOUT = 1 VPP -20 0.8 MEASURE CH B CROSSTALK (dBc) -30 VOUT (V) 0.4 0 -0.4 -50 -60 -70 AV = 2V/V -0.8 -1.2 -40 -80 VOUT = 2.0 VPP 0 5 -90 1 10 15 20 25 30 35 40 45 50 10 Figure 29. 1000 Figure 30. Distortion vs. Output Voltage Distortion vs. Frequency -50 -40 AV = 2 V/V f = 10 MHz VOUT = 2 VPP -50 HD3 -60 DISTORTION (dBc) DISTORTION (dBc) 100 FREQUENCY (MHz) TIME (ns) -70 HD2 -80 -60 HD3 -70 HD2 -80 -90 -90 -100 0 1 2 3 4 1 10 100 FREQUENCY (MHz) VOUT (VPP) Figure 31. Figure 32. DC Errors vs. Temperature 11 0.8 9 IBI 7 0.7 5 0.65 VOS 0.6 3 0.55 1 0.5 -1 0.45 -3 IBN 0.4 -40 -20 BIAS CURRENT (PA) OFFSET VOLTAGE (mV) 0.75 -5 0 20 40 60 80 100 120 TEMPERATURE (C) Figure 33. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 11 LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com APPLICATION INFORMATION +2.5V 6.8 PF AV = 1 +RF/RG = VOUT/VIN 0.1 PF VIN CPOS + CSS 0.01 PF RIN VOUT - CNEG 0.1 PF RF RG 6.8 PF -2.5V Figure 34. Recommended Non-Inverting Gain Circuit +2.5V 6.8 PF 0.1 PF AV = - RF RG = VOUT VIN CPOS 25: VIN CSS 0.01 PF + - RG VOUT CNEG 0.1 PF RT 6.8 PF -2.5V RF SELECT RT TO YIELD DESIRED RIN = RT||RG Figure 35. Recommended Inverting Gain Circuit General Information The LMH6733 is a high speed current feedback amplifier, optimized for very high speed and low distortion. The LMH6733 has no internal ground reference so single or split supply configurations are both equally useful. Feedback Resistor Selection One of the key benefits of a current feedback operational amplifier is the ability to maintain optimum frequency response independent of gain by using the appropriate values for the feedback resistor (RF). The Electrical Characteristics and Typical Performance plots specify an RF of 340, a gain of +2 V/V and 2.5V power supplies (unless otherwise specified). Generally, lowering RF from its recommended value will peak the frequency response and extend the bandwidth while increasing the value of RF will cause the frequency response to roll off faster. Reducing the value of RF too far below its recommended value will cause overshoot, ringing and, eventually, oscillation. 12 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 450 RECOMMENDED RF (:) 400 350 INVERTING (AV < 0) 300 250 200 NON-INVERTING (AV > 0) 150 100 50 0 1 2 3 4 5 6 7 8 9 10 |GAIN| (V/V) Figure 36. Recommended RF vs. Gain See Figure 36 for selecting a feedback resistor value for gains of 1 to 10. Since each application is slightly different it is worth some experimentation to find the optimal RF for a given circuit. In general a value of RF that produces about 0.1 dB of peaking is the best compromise between stability and maximal bandwidth. Note that it is not possible to use a current feedback amplifier with the output shorted directly to the inverting input. The buffer configuration of the LMH6733 requires a 324 feedback resistor for stable operation. The LMH6733 has been optimized for high speed operation. As shown in Figure 36 the suggested value for RF decreases for higher gains. Due to the impedance of the input buffer there is a practical limit for how small RF can go, based on the lowest practical value of RG. This limitation applies to both inverting and non-inverting configurations. For the LMH6733 the input resistance of the inverting input is approximately 30 and 20 is a practical (but not hard and fast) lower limit for RG. The LMH6733 begins to operate in a gain bandwidth limited fashion in the region where RG is nearly equal to the input buffer impedance. Note that the amplifier will operate with RG values well below 20, however results may be substantially different than predicted from ideal models. In particular the voltage potential between the inverting and non-inverting inputs cannot be expected to remain small. Inverting gain applications that require impedance matched inputs may limit gain flexibility somewhat (especially if maximum bandwidth is required). The impedance seen by the source is RG || RT (RT is optional). The value of RG is RF /gain. Thus for an inverting gain of -5 V/V and an optimal value for RF the input impedance is equal to 55. Using a termination resistor this can be brought down to match a 25 source; however, a 150 source cannot be matched. To match a 150 source would require using a 1050 feedback resistor and would result in reduced bandwidth. For more information see Application Note OA-13 which describes the relationship between RF and closed-loop frequency response for current feedback operational amplifiers. The value for the inverting input impedance for the LMH6733 is approximately 30. The LMH6733 is designed for optimum performance at gains of +1 to +10 V/V and -1 to -9 V/V. Higher gain configurations are still useful; however, the bandwidth will fall as gain is increased, much like a typical voltage feedback amplifier. Active Filter The choice of reactive components requires much attention when using any current feedback operational amplifier as an active filter. Reducing the feedback impedance, especially at higher frequencies, will almost certainly cause stability problems. Likewise capacitance on the inverting input should be avoided. See Application Notes OA-07 and OA-26 for more information on Active Filter applications for Current Feedback Op Amps. When using the LMH6733 as a low pass filter the value of RF can be substantially reduced from the value recommended in the RF vs. Gain charts. The benefit of reducing RF is increased gain at higher frequencies, which improves attenuation in the stop band. Stability problems are avoided because in the stop band additional device bandwidth is used to cancel the input signal rather than amplify it. The benefit of this change depends on the particulars of the circuit design. With a high pass filter configuration reducing RF will likely result in device instability and is not recommended. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 13 LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com 6.8 PF + VSUPPLY C2 0.1 PF C1 RIN 75: X1 VIN + - + VOUT - RG 340: ROUT 75: RF 340: 0.1 PF C3 6.8 PF - VSUPPLY C4 Figure 37. Typical Video Application X1 + RIN 51: - + - RG 340: ROUT 51: CL 10 pF RL 1 k: RF 340: Figure 38. Decoupling Capacitive Loads Driving Capacitive Loads Capacitive output loading applications will benefit from the use of a series output resistor ROUT. shows the use of a series output resistor, ROUT, to stabilize the amplifier output under capacitive loading. Capacitive loads of 5 to 120 pF are the most critical, causing ringing, frequency response peaking and possible oscillation. The chart "Frequency Response vs. Capacitive Load" give a recommended value for selecting a series output resistor for mitigating capacitive loads. The values suggested in the charts are selected for .5 dB or less of peaking in the frequency response. This gives a good compromise between settling time and bandwidth. For applications where maximum frequency response is needed and some peaking is tolerable, the value of ROUT can be reduced slightly from the recommended values. CAT5 High Definition Video Transmission The LMH6733 can be used to send component 1080i High Definition (HD) video over CAT5 twisted-pairs. As shown Figure 39 , the LMH6733 can be utilized to perform all three video transmitter, video receiver, and equalization circuitry. The equalization circuitry enhances the video signal to accomodate for the CAT5 attenuation over various cable lengths. Refer to application note AN-1822 for more details regarding this application. 14 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 HD Component Video Input (Y, Pr, Pb) VIDEO RECEIVER VIDEO EQUALIZER LMH6733 LMH6733 CAT5 CABLE LMH6733 RT VIDEO TRANSMITTER RL Figure 39. CAT5 High Definition Video Transmission +5V C2 0.1 PF R1 5 k: C1 10 PF VIN RT 75: (OPTIONAL) C3 100 PF R2 5 k: C0 1000 PF + - + CIN 47 PF R3 10 k: R0 75: VLOAD LMH6733 U1 - RL 75: R4 680: +5V RG 680: RF 340: C3 1 PF Figure 40. AC Coupled Single Supply Video Amplifier AC-Coupled Video The LMH6733 can be used as an AC-coupled single supply video amplifier for driving 75 coax with a gain of 2. The input signal is nominally 0.7V or 1.0V for component YPRPB and RGB, depending on the presence of a sync. R1, R2, and R3 simply set the input to the center of the input linear range while CIN AC couples the video onto the op amp's input. As can be seen in , Figure 40 amplifier U1 is used in a positive gain configuration set for a closed loop gain of 2. The feedback resistor RF is 340. The gain resistor is created from the parallel combination of RG and R4, giving a Thevenin equivalent of 340 connected to 2.5V. The 75 back termination resistor RO divides the signal such that VOUT equals a buffered version of VIN. The back termination will eliminate any reflection of the signal that comes from the load. The input termination resistor, RT, is optional - it is used only if matching of the incoming line is necessary. In some applications, it is recommended that a small valued ceramic capacitor be used in parallel with CO which is itself electrolytic because of its rather large value. The ceramic cap will tend to shunt the inductive behavior of this electrolytic cap, CO, at higher frequencies for an improved overall, low-impedance output. Inverting Input Parasitic Capacitance Parasitic capacitance is any capacitance in a circuit that was not intentionally added. It comes about from electrical interaction between conductors. Parasitic capacitance can be reduced but never entirely eliminated. Most parasitic capacitances that cause problems are related to board layout or lack of termination on transmission lines. Please see the section on Layout Considerations for hints on reducing problems due to parasitic capacitances on board traces. Transmission lines should be terminated in their characteristic impedance at both ends. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 15 LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com High speed amplifiers are sensitive to capacitance between the inverting input and ground or power supplies. This shows up as gain peaking at high frequency. The capacitor raises device gain at high frequencies by making RG appear smaller. Capacitive output loading will exaggerate this effect. In general, avoid introducing unnecessary parasitic capacitance at both the inverting input and the output. One possible remedy for this effect is to slightly increase the value of the feedback (and gain set) resistor. This will tend to offset the high frequency gain peaking while leaving other parameters relatively unchanged. If the device has a capacitive load as well as inverting input capacitance using a series output resistor as described in the section on "Driving Capacitive Loads" will help. Layout Considerations Whenever questions about layout arise, use the evaluation board as a guide. The LMH730275 is the evaluation board supplied with samples of the LMH6733. To reduce parasitic capacitances ground and power planes should be removed near the input and output pins. Components in the feedback loop should be placed as close to the device as possible. For long signal paths controlled impedance lines should be used, along with impedance matching elements at both ends. Bypass capacitors should be placed as close to the device as possible. Bypass capacitors from each rail to ground are applied in pairs. The larger electrolytic bypass capacitors can be located farther from the device, the smaller ceramic capacitors should be placed as close to the device as possible. The LMH6733 has multiple power and ground pins for enhanced supply bypassing. Every pin should ideally have a separate bypass capacitor. Sharing bypass capacitors may slightly degrade second order harmonic performance, especially if the supply traces are thin and /or long. In Figure 34 and Figure 35 CSS is optional, but is recommended for best second harmonic distortion. Another option to using CSS is to use pairs of .01 F and .1 F ceramic capacitors for each supply bypass. Video Performance The LMH6733 has been designed to provide excellent performance with production quality video signals in a wide variety of formats such as HDTV and High Resolution VGA. NTSC and PAL performance is nearly flawless. Best performance will be obtained with back terminated loads. The back termination reduces reflections from the transmission line and effectively masks transmission line and other parasitic capacitances from the amplifier output stage. Figure 37 shows a typical configuration for driving a 75 cable. The amplifier is configured for a gain of two to make up for the 6 dB of loss in ROUT. MAXIMUM POWER DISSIPATION (W) 2 1.8 225 LFPM FORCED AIR 1.6 1.4 1.2 1 STILL AIR 0.8 0.6 0.4 0.2 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (C) Figure 41. Maximum Power Dissipation 16 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 Power Dissipation The LMH6733 is optimized for maximum speed and performance in the small form factor of the standard SSOP16 package. To achieve its high level of performance, the LMH6733 consumes an appreciable amount of quiescent current which cannot be neglected when considering the total package power dissipation limit. The quiescent current contributes to about 40 C rise in junction temperature when no additional heat sink is used (VS = 5V, all 3 channels on). Therefore, it is easy to see that proper precautions need to be taken in order to make sure the junction temperature's absolute maximum rating of 150C is not violated. To ensure maximum output drive and highest performance, thermal shutdown is not provided. Therefore, it is of utmost importance to make sure that the TJMAX is never exceeded due to the overall power dissipation (all 3 channels). With the LMH6733 used in a back-terminated 75 RGB analog video system (with 2 VPP output voltage), the total power dissipation is around 305 mW of which 220 mW is due to the quiescent device dissipation (output black level at 0V). With no additional heat sink used, that puts the junction temperature to about 120 C when operated at 85C ambient. To reduce the junction temperature many options are available. Forced air cooling is the easiest option. An external add-on heat-sink can be added to the SSOP-16 package, or alternatively, additional board metal (copper) area can be utilized as heat-sink. An effective way to reduce the junction temperature for the SSOP-16 package (and other plastic packages) is to use the copper board area to conduct heat. With no enhancement the major heat flow path in this package is from the die through the metal lead frame (inside the package) and onto the surrounding copper through the interconnecting leads. Since high frequency performance requires limited metal near the device pins the best way to use board copper to remove heat is through the bottom of the package. A gap filler with high thermal conductivity can be used to conduct heat from the bottom of the package to copper on the circuit board. Vias to a ground or power plane on the back side of the circuit board will provide additional heat dissipation. A combination of front side copper and vias to the back side can be combined as well. Follow these steps to determine the maximum power dissipation for the LMH6733: 1. Calculate the quiescent (no-load) power: PAMP = ICC X (VS) where * VS = V+-V- (1) 2. Calculate the RMS power dissipated in the output stage: PD (rms) = rms ((VS - VOUT) X IOUT) where * * VOUT and IOUT are the voltage and the current across the external load VS is the total supply voltage (2) 3. Calculate the total RMS power: PT = PAMP+PD (3) The maximum power that the LMH6733, package can dissipate at a given temperature can be derived with the following equation (See Figure 41): PMAX = (150C/W- TAMB)/ JA where * * * TAMB = ambient temperature (C) JA = thermal resistance, from junction to ambient, for a given package (C/W) For the SSOP package JA is 120C/W (4) Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 17 LMH6733 SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 www.ti.com ESD Protection The LMH6733 is protected against electrostatic discharge (ESD) on all pins. The LMH6733 will survive 2000V Human Body Model and 200V Machine Model events. Under closed loop operation the ESD diodes have no affect on circuit performance. There are occasions, however, when the ESD diodes will be evident. If the LMH6733 is driven by a large signal while the device is powered down the ESD diodes will conduct. The current that flows through the ESD diodes will either exit the chip through the supply pins or will flow through the device, hence it is possible to power up a chip with a large signal applied to the input pins. Shorting the power pins to each other will prevent the chip from being powered up through the input. Evaluation Boards Texas Instruments provides the following evaluation boards as a guide for high frequency layout and as an aid in device testing and characterization. Many of the datasheet plots were measured with these boards. 18 Device Package Evaluation Board Part Number LMH6733MQ SSOP LMH730275 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 LMH6733 www.ti.com SNOSAW0D - JANUARY 2007 - REVISED MAY 2013 REVISION HISTORY Changes from Revision C (April 2013) to Revision D * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 18 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LMH6733 19 PACKAGE OPTION ADDENDUM www.ti.com 13-Dec-2014 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMH6733MQ/NOPB ACTIVE SSOP DBQ 16 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LH67 33MQ LMH6733MQX/NOPB ACTIVE SSOP DBQ 16 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LH67 33MQ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 13-Dec-2014 In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 9-Jul-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device LMH6733MQX/NOPB Package Package Pins Type Drawing SSOP DBQ 16 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.5 B0 (mm) K0 (mm) P1 (mm) 5.4 2.0 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 9-Jul-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMH6733MQX/NOPB SSOP DBQ 16 2500 367.0 367.0 35.0 Pack Materials-Page 2 PACKAGE OUTLINE DBQ0016A SSOP - 1.75 mm max height SCALE 2.800 SHRINK SMALL-OUTLINE PACKAGE C SEATING PLANE .228-.244 TYP [5.80-6.19] A .004 [0.1] C PIN 1 ID AREA 16 1 14X .0250 [0.635] 2X .175 [4.45] .189-.197 [4.81-5.00] NOTE 3 8 9 B .150-.157 [3.81-3.98] NOTE 4 16X .008-.012 [0.21-0.30] .007 [0.17] C A B .069 MAX [1.75] .005-.010 TYP [0.13-0.25] SEE DETAIL A .010 [0.25] GAGE PLANE .004-.010 [0.11-0.25] 0 -8 .016-.035 [0.41-0.88] (.041 ) [1.04] DETAIL A TYPICAL 4214846/A 03/2014 NOTES: 1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed .006 inch, per side. 4. This dimension does not include interlead flash. 5. Reference JEDEC registration MO-137, variation AB. www.ti.com EXAMPLE BOARD LAYOUT DBQ0016A SSOP - 1.75 mm max height SHRINK SMALL-OUTLINE PACKAGE 16X (.063) [1.6] SEE DETAILS SYMM 1 16 16X (.016 ) [0.41] 14X (.0250 ) [0.635] 9 8 (.213) [5.4] LAND PATTERN EXAMPLE SCALE:8X METAL SOLDER MASK OPENING SOLDER MASK OPENING .002 MAX [0.05] ALL AROUND METAL .002 MIN [0.05] ALL AROUND SOLDER MASK DEFINED NON SOLDER MASK DEFINED SOLDER MASK DETAILS 4214846/A 03/2014 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com EXAMPLE STENCIL DESIGN DBQ0016A SSOP - 1.75 mm max height SHRINK SMALL-OUTLINE PACKAGE 16X (.063) [1.6] SYMM 1 16 16X (.016 ) [0.41] SYMM 14X (.0250 ) [0.635] 9 8 (.213) [5.4] SOLDER PASTE EXAMPLE BASED ON .005 INCH [0.127 MM] THICK STENCIL SCALE:8X 4214846/A 03/2014 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LMH6733MQ/NOPB LMH6733MQX/NOPB