Fiber Optic Components High-speed TTL Receiver FEATURES * Designed to meet industrial LAN (Local Area Network) specifications * Converts optical input into an electrical signal * Typical sensitivity at 660 nm is -21 dBm * Single 5 V supply * High-speed (dc to 16 Mbps) * Metal SMA barrel for high mechanical stability * Separate grounding of the barrel provides excellent RFII/EMI/ESD shielding * Low-cost plastic version (HFD7000-212) available * PIN-compatible with Honeywell's HFD3403 5 Mbps receiver HFD7000-2XX Series The HFD7000 Series are high-speed optical receivers designed for data transmission in industrial LAN applications. The monolithic CMOS chip consists of a large area photodiode, pre-amplifier with controlled gain, a post amplifier, a comparator and TTL output stage. The integrated voltage regulator provides easy use in many applications. The chip's silicon material is optimized for 660 nm operation The on-chip controlled gain provides a wide dyanmic range and low pulse width distortion (PWD). The chip is mounted in a metal TO-18 package. In addition, the outer package of the HFD7000-202 has a metal barrel for high mechanical stability and excellent shielding against RFI/EMI and ESD. This feature allows the receiver to operate in harsh environments. The receiver is designed to work with Honeywell's high-speed 660 nm transmitter, the HFE 7000. For maximum performance of this receiver, a 0.1 F capacitor must be mounted between Vcc and ground no more than 3,0 mm [0.12 in] away from the housing. A 4.7 resistor in series with Vcc increases the filter's performance. This minimizes external noise and allows the maximum sensitivity to be maintained. WARNING PERSONAL INJURY DO NOT USE these products as safety or emergency stop devices, or in any other application where failure of the product could result in personal injury. Failure to comply with these instructions could result in death or serious injury. Sensing and Control WARNING MISUSE OF DOCUMENTATION * The information presented in this product sheet is for reference only. Do not use this document as a product installation guide. * Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in death or serious injury. Fiber Optic Components High-speed TTL Receiver HFD7000-2XX Series OPERATION Optical power (photons) from the fiber strikes the active area of the photodiode and is converted to an electrical signal. The current is then converted to a voltage in the transimpedance pre-amplifier. The controlled gain limits the light current created by the photodiode in both the transimpedance pre-amplifier and in the post-amplifier. This avoids a possible overcharge of the amplifier and assures optimum PWD performance. The signal is compared with a threshold defining the system's sensitivity limit. A final buffer provides a TTL output. The level sensitive behavior makes the system robust with respect to the external interference (e.g. current/voltage spikes). The regulator supplies the entire system to ensure high rejection of power supply noise. ABSOLUTE MAXIMUM RATINGS (25 C [77 F] free air temperature unless otherwise noted.) Storage temperature Lead solder temperature Supply voltage Junction temperature -40 C to 100 C [-40 F to 212 F] A/W 0.5 n+/p-sub 0.4 0.3 0.2 0.1 0 300 400 500 600 700 800 900 10001100 1200 (nm) NOTICE * Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. * Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Failure to comply with these instructions could result in death or serious injury. 10 s at 260 C [500 F] 6V 150 C [302 F] RECOMMENDED OPERATING CONDITIONS Operating Temperature Supply voltage Optical input power FIGURE 1: SPECTRAL SENSITIVITY 0 C to 70 C [32 F to 158 F] 4.75 V to 5.25 V -20 dBm to -5 dBm TABLE 1: ELECTRO-OPTICAL CHARACTERISTICS (TC = 25 C [77 F], VCC = 5 V unless noted) Parameter Data rate Current consumption 660 nm Max. received power/optical level LOW Max. received power/optical level HIGH Max. received power/optical level HIGH Output voltage high Output voltage low Rise time Fall time Pulse width distortion Dynamic range Bit error rate 2 Honeywell * Sensing and Control Test Condition Symbol Min. Typical - - Max . 16 45 - - dc Icc dc - 1 mm/POF 1 mm/POF 1 mm/POF IOH = 2 mA@20 pf load IOL = 2 mA@20 pf load 10 % - 90 % 90 % - 10 % f = 8 MHz, 50 % duty cycle, PoIN = -20 dBm to -5 dBm (average) - - PRmaxL PRmaxL PRminH VOHIGH VOLOW tr tf PWD - BER Unit Mbps mA - - -20 2.4 - - - - - - - - - 6 8 - -31 -5 - - 0.4 10 10 22 dBm dBm dBm V V ns ns ns 15 - - - - <10-9 dB - Fiber Optic Components High-speed TTL Receiver HFD7000-2XX Series FIGURE 2. HFD7000-212/215 (For reference only, mm) Figure 3. HFD7000-202 (For reference only, mm) FIGURE 4: Waveform 100 % OPTICAL INPUT 50 % PULSE WIDTH 0% 100 % 2.4 V ELECTRICAL 50 % INPUT PULSE WIDTH 0.4 V 0% tf tr Honeywell * Sensing and Control 3 Fiber Optic Components High-speed TTL Receiver ORDER GUIDE Catalog Listing HFD7000-202 HFD7000-212 HFD7000-215 Description Metal barrel Fiberglass reinforced, non-conductive barrel Carbon-fiber reinforced, conductive barrel HFD7000-2XX Series WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell will repair or replace without charge those items it finds defective. The foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this printing. However, we assume no responsibility for its use. While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the application. For application assistance, current specifications, or name of the nearest Authorized Distributor, contact a nearby sales office. Or call: 1-800-537-6945 USA/Canada 1-815-235-6847 International FAX 1-815-235-6545 USA INTERNET www.honeywell.com/sensing info.sc@honeywell.com Sensing and Control www.honeywell.com/sensing Honeywell 11 West Spring Street Freeport, Illinois 61032 100101-2-EN IL50 GLO 1004 Printed in USA Copyright 2004 Honeywell International Inc. All Rights Reserved.