Fiber Optic Components
High-speed TTL Receiver HFD7000-2XX Serie
s
Sensin
g
and Control
FEATURES
Designed to meet industrial
LAN (Local Area Network)
specifications
Converts optical input into
an electrical signal
Typical sensitivity at
660 nm is -21 dBm
Single 5 V supply
High-speed (dc to
16 Mbps)
Metal SMA barrel for high
mechanical stability
Separate grounding of the
barrel provides excellent
RFII/EMI/ESD shielding
Low-cost plastic version
(HFD7000-212) available
PIN-compatible with
Honeywell’s HFD3403 5
Mbps receiver
WARNING
PERSONAL INJURY
DO NOT USE these
products as safety or
emergency stop devices, or
in any other application
where failure of the product
could result in personal
injury.
Failure to comply with
these instructions could
result in death or serious
injury.
The HFD7000 Series are high-speed optical receivers designed for data
transmission in industrial LAN applications. The monolithic CMOS chip
consists of a large area photodiode, pre-amplifier with controlled gain, a post
amplifier, a comparator and TTL output stage. The integrated voltage
regulator provides easy use in many applications.
The chip’s silicon material is optimized for 660 nm operation The on-chip
controlled gain provides a wide dyanmic range and low pulse width distortion
(PWD).
The chip is mounted in a metal TO-18 package. In addition, the outer
package of the HFD7000-202 has a metal barrel for high mechanical stability
and excellent shielding against RFI/EMI and ESD. This feature allows the
receiver to operate in harsh environments.
The receiver is designed to work with Honeywell’s high-speed 660 nm
transmitter, the HFE 7000.
For maximum performance of this receiver, a 0.1 µF capacitor must be
mounted between Vcc and ground no more than 3,0 mm [0.12 in] away from
the housing. A 4.7 resistor in series with Vcc increases the filter’s
performance. This minimizes external noise and allows the maximum
sensitivity to be maintained.
WARNING
MISUSE OF DOCUMENTATION
The information presented in this product sheet is for reference only. Do
not use this document as a product installation guide.
Complete installation, operation, and maintenance information is
provided in the instructions supplied with each product.
Failure to comply with these instructions could result in death or
serious injury.
Fiber Optic Components
High-speed TTL Receiver HFD7000-2XX Series
2 Honeywell Sensing and Control
OPERATION
Optical power (photons) from the fiber strikes the
active area of the photodiode and is converted to an
electrical signal. The current is then converted to a
voltage in the transimpedance pre-amplifier. The
controlled gain limits the light current created by the
photodiode in both the transimpedance pre-amplifier
and in the post-amplifier. This avoids a possible
overcharge of the amplifier and assures optimum
PWD performance.
The signal is compared with a threshold defining
the system’s sensitivity limit. A final buffer provides a
TTL output. The level sensitive behavior makes the
system robust with respect to the external
interference (e.g. current/voltage spikes). The
regulator supplies the entire system to ensure high
rejection of power supply noise.
ABSOLUTE MAXIMUM RATINGS (25 ºC [77 ºF] free
air temperature unless otherwise noted.)
Storage
temperature
-40 ºC to 100 ºC [-40 ºF to 212 ºF]
Lead solder
temperature
10 s at 260 ºC [500 ºF]
Supply voltage 6 V
Junction
temperature
150 ºC [302 ºF]
RECOMMENDED OPERATING CONDITIONS
Operating
Temperature
0 ºC to 70 ºC [32 ºF to 158 ºF]
Supply voltage 4.75 V to 5.25 V
Optical input
power
-20 dBm to -5 dBm
FIGURE 1: SPECTRAL SENSITIVITY
300 400 600 700500 800 1200900 10001100
(nm)
0
0.1
0.2
0.3
0.4
0.5
A/W n+/p-sub
NOTICE
Stresses greater than those listed under “Absolute
Maximum Ratings” may cause permanent damage
to the device.
This is a stress rating only and functional
operation of the device at these or any other
conditions above those indicated in the
operational section of this specification is not
implied.
Exposure to absolute maximum rating conditions
for extended periods of time may affect reliability.
Failure to comply with these instructions could
result in death or serious injury.
TABLE 1: ELECTRO-OPTICAL CHARACTERISTICS (TC = 25 ºC [77 ºF], VCC = 5 V unless noted)
Parameter Test Condition Symbol Min. Typical Max
.
Unit
Data rate dc dc 16 Mbps
Current consumption Icc 45 mA
660 nm
Max. received power/optical level LOW 1 mm/POF PRmaxL -31 dBm
Max. received power/optical level HIGH 1 mm/POF PRmaxL -5 dBm
Max. received power/optical level HIGH 1 mm/POF PRminH -20 dBm
Output voltage high IOH = 2 mA@20 pf load VOHIGH 2.4 V
Output voltage low IOL = 2 mA@20 pf load VOLOW 0.4 V
Rise time 10 % - 90 % tr 6 10 ns
Fall time 90 % - 10 % tf 8 10 ns
Pulse width distortion f = 8 MHz, 50 % duty
cycle, PoIN = -20 dBm
to -5 dBm (average)
PWD ±22 ns
Dynamic range 15 dB
Bit error rate BER <10-9
Fiber Optic Components
High-speed TTL Receiver HFD7000-2XX Series
Honeywell Sensing and Control 3
FIGURE 2. HFD7000-212/215 (For reference only, mm)
Figure 3. HFD7000-202 (For reference only, mm)
FIGURE 4: Waveform
PULSE
WIDTH
PULSE
WIDTH
OPTICAL
INPUT
ELECTRICAL
INPUT
100 %
50 %
0 %
100 %
2.4 V
0.4 V
0 %
50 %
t
f
t
r
Fiber Optic Components
High-speed TTL Receiver HFD7000-2XX Series
Sensing and Control
www.honeywell.com/sensing
Honeywell
11 West Spring Street
Freeport, Illinois 61032
100101-2-EN IL50 GLO 1004 Printed in USA
Copyright 2004 Honeywell International Inc. All Rights Reserved.
ORDER GUIDE
Catalog Listing Description
HFD7000-202 Metal barrel
HFD7000-212 Fiberglass reinforced, non-conductive barrel
HFD7000-215 Carbon-fiber reinforced, conductive barrel
WARRANTY/REMEDY
Honeywell warrants goods of its
manufacture as being free of
defective materials and faulty
workmanship. Contact your local
sales office for warranty information.
If warranted goods are returned to
Honeywell during the period of
coverage, Honeywell will repair or
replace without charge those items
it finds defective. The foregoing is
Buyer’s sole remedy and is in
lieu of all other warranties,
expressed or implied, including
those of merchantability and
fitness for a particular purpose.
Specifications may change without
notice. The information we supply
is believed to be accurate and
reliable as of this printing. However,
we assume no responsibility for its
use.
While we provide application
assistance personally, through our
literature and the Honeywell web
site, it is up to the customer to
determine the suitability of the
product in the application.
For application assistance, current
specifications, or name of the
nearest Authorized Distributor,
contact a nearby sales office. Or
call:
1-800-537-6945 USA/Canada
1-815-235-6847 International
FAX
1-815-235-6545 USA
INTERNET
www.honeywell.com/sensing
info.sc@honeywell.com