H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4
April 2013
H11L1M, H11L2M, H11L3M
6-Pin DIP Optocoupler
Features
■
High Data Rate, 1 MHz typical (NRZ)
■
Free From Latch-up and Oscilliation Throughout
Voltage and Temperature Ranges
■
Microprocessor Compatible Drive
■
Logic Compatible Output Sinks 16 mA at 0.4 V
Maximum
■
Guaranteed On/Off Threshold Hysteresis
■
Wide Supply Voltage Capability, Compatible With All
Popular Logic Systems
■
Underwriters Laboratory (UL) Recognized—
File #E90700, Volume 2
■
VDE Recognized – File #102497 – Add Option V
(e.g., H11LIVM)
Applications
■
Logic-to-Logic Isolator
■
Programmable Current Level Sensor
■
Line Receiver—Eliminate Noise and Transient
Problems
■
A.C. to TTL Conversion—Square Wave Shaping
■
Digital Programming of Power Supplies
■
Interfaces Computers with Peripherals
Description
The H11LXM series has a high speed integrated circuit
detector optically coupled to a gallium-arsenide infrared
emitting diode. The output incorporates a Schmitt trigger,
which provides hysteresis for noise immunity and pulse
shaping. The detector circuit is optimized for simplicity of
operation and utilizes an open collector output for
maximum application flexibility.
Schematic Package Outlines
1
2
6
5 GND
4VO
VCC
ANODE
CATHODE
3
Truth Table
Input Output
HL
LH
Figure 1. Schematic Figure 2. Package Outlines
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 2
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
Absolute Maximum Ratings
Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be
operable above the recommended operating conditions and stressing the parts to these levels is not recommended.
In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability.
The absolute maximum ratings are stress ratings only.
T
A
= 25°C unless otherwise specified.
Symbol Parameters Value Units
Total Device
T
STG
Storage Temperature -40 to +150 °C
T
OPR
Operating Temperature -40 to +85 °C
T
SOL
Lead Solder Temperature 260 for 10 seconds °C
P
D
Total Device Power Dissipation @ 25°C 250 mW
Derate Above 25°C 2.94 mW/°C
Emitter
I
F
Continuous Forward Current 60 mA
V
R
Reverse Voltage 6 V
I
F
(pk) Forward Current – Peak (1 µs pulse, 300 pps) 3.0 A
P
D
LED Power Dissipation 25°C Ambient 120 mW
Derate Linearly From 25°C 1.41 mW/°C
Detector
P
D
Detector Power Dissipation @ 25°C 150 mW
Derate Linearly from 25°C 2.0 mW/°C
V
O
V
45
Allowed Range 0 to 16 V
V
CC
V
65
Allowed Range 3 to 16 V
I
O
I
4
Output Current 50 mA
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 3
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
Electrical Characteristics
T
A
= 25°C unless otherwise specified.
Individual Component Characteristics
Transfer Characteristics
Isolation Characteristics
Note:
1. Maximum I
F(ON)
is the maximum current required to trigger the output. For example, a 1.6 mA maximum trigger current would
require the LED to be driven at a current greater than 1.6 mA to guarantee the device will turn on. A 10% guard band is
recommended to account for degradation of the LED over its lifetime. The maximum allowable LED drive current is 60 mA.
Symbol
Parameters
Test Conditions Device Min. Typ. Max. Units
Emitter
V
F
Input Forward Voltage I
F
= 10 mA All 1.2 1.5 V
I
F
= 0.3 mA 0.75 1.0
I
R
Reverse Current V
R
= 3 V All 10 µA
C
J
Capacitance V = 0, f = 1.0 MHz All 100 pF
Detector
V
CC
Operating Voltage Range All 3 15 V
I
CC(off)
Supply Current I
F
= 0, V
CC
= 5 V All 1.6 5.0 mA
I
OH
Output Current, High I
F
= 0, V
CC
= V
O
= 15 V All 100 µA
Symbol
Parameter
Test Conditions Device Min. Typ. Max. Units
DC Characteristics
I
CC(on)
Supply Current I
F
= 10 mA, V
CC
= 5 V All 1.6 5.0 mA
V
OL
Output Voltage, low R
L
= 270
Ω
,V
CC
= 5 V,
I
F
= I
F(on)
max.
All 0.2 0.4 V
I
F(on)
Turn-On Threshold Current
(1)
R
L
= 270
Ω
, V
CC
= 5 V H11L1M 1.6 mA
H11L2M 10.0
H11L3M 5.0
I
F(off)
Turn-Off Threshold Current R
L
= 270
Ω
, V
CC
= 5 V All 0.3 1.0 mA
I
F(off)
/I
F(on)
Hysteresis Ratio R
L
= 270
Ω
, V
CC
= 5 V All 0.50 0.75 0.90
AC Characteristics, Switching Speed
t
on
Turn-On time R
L
= 270
Ω
, V
CC
= 5 V,
I
F
= I
F(on)
, T
A
= 25°C
All 1.0 4 µs
t
f
Fall Time R
L
= 270
Ω
, V
CC
= 5 V,
I
F
= I
F(on)
, T
A
= 25°C
All 0.1 µs
t
off
Turn-Off Time R
L
= 270
Ω
, V
CC
= 5 V,
I
F
= I
F(on)
, T
A
= 25°C
All 1.2 4 µs
t
r
Rise time R
L
= 270
Ω
, V
CC
= 5 V,
I
F
= I
F(on)
, T
A
= 25°C
All 0.1 µs
Data Rate All 1.0 MHz
Symbol
Parameter
Test Conditions Min. Typ. Max. Units
V
ISO
Input-Output Isolation Voltage t =1 second 7500 V
PEAK
C
ISO
Isolation Capacitance V
I-O
= 0 V, f = 1 MHz 0.4 0.6 pF
R
ISO
Isolation Resistance V
I-O
= ±500 VDC 10
11
Ω
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 4
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
Safety and Insulation Ratings
As per IEC 60747-5-2, this optocoupler is suitable for “safe electrical insulation” only within the safety limit data.
Compliance with the safety ratings shall be ensured by means of protective circuits.
Symbol Parameter Min. Typ. Max. Unit
Installation Classifications per DIN VDE 0110/1.89
Table 1
For Rated Main Voltage < 150 Vrms I-IV
For Rated Main voltage < 300 Vrms I-IV
Climatic Classification 55/100/21
Pollution Degree (DIN VDE 0110/1.89) 2
CTI Comparative Tracking Index 175
VPR Input to Output Test Voltage, Method b,
VIORM x 1.875 = VPR, 100% Production Test
with tm = 1 second, partial discharge < 5 pC
1594 Vpeak
Input to Output Test Voltage, Method a,
VIORM x 1.5 = VPR, Type and Sample Test
with tm = 60 seconds, partial discharge < 5 pC
1275 Vpeak
VIORM Max. Working Insulation Voltage 850 Vpeak
VIOTM Highest Allowable Over Voltage 6000 Vpeak
External Creepage 7 mm
External Clearance 7 mm
Insulation Thickness 0.5 mm
RIO Insulation Resistance at Ts, VIO = 500 V 109 Ω
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 5
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
Typical Performance Curves
Figure 4. Threshold Current vs. Supply Voltage
Figure 3. Transfer Characteristics
V
CC
– SUPPLY VOLTAGE (V)
0 2 4 6 8 10121416
I
F
– THRESHOLD CURRENT (NORMALIZED)
0.4
0.6
0.8
1.0
1.2
1.4
1.6
F NORMALIZED TO:
IF(ON) AT VCC = 5 V
TA = 25oC
I
Figure 5. Threshold Current vs. Supply Temperature
T
A
– TEMPERATURE (
o
C)
-50 -25 0 25 50 75 100
I
F(On)
, I
F(Off)
– THRESHOLD CURRENT (NORMALIZED)
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
NORMALIZED TO:
VCC = 5 V
T
A
= 25
o
C
Figure 6. Output Voltage, Low vs. Load Current
I
O
– LOAD CURRENT (mA)
1 10 100
V
OL
- OUTPUT VOLTAGE, LOW (V)
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
2
0.1
1
TURN ON THRESHOLD
TURN OFF THRESHOLD
IF = I F(ON)
VCC = 5 V
RL = 270 Ω
IF
– INPUT CURRENT (mA)
0123
V
O – OUTPUT VOLTAGE (V)
0
1
2
3
4
5
6
VOH
VOL
IF( OF F) IF(ON)
VCC = 5 V
RL = 270 Ω
TA = 25°C
Figure 7. Supply Current vs. Supply Voltage Figure 8. LED Forward Voltage vs. Forward Current
V
CC
– SUPPLY VOLTAGE (V)
0246810121416
I
C
– SUPPLY CURRENT (mA)
0
1
2
3
4
5
6
I
F
= 5mA
T
A
= 0
25
70
°
C
°
C
°
C
I
F
= 0 mA
T
A
= 0 70
25
I
F
– LED FORWARD CURRENT (mA)
V
F
– FORWARD VOLTAGE (V)
1 10 100
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
TA = 25°C
TA = 55°C
TA = 100°C
°
C
°
C
°
C
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 6
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
C
RERL
VIN 5V
VO
90%
ton
tr
tf
10%
50%
toff
IF
1
2
H11L1
VIN
tr = tf = 0.01 μs
Z = 50
270Ω
I65V
VO
5
6
4
0
Figure 9. Switching Test Circuit and Waveforms
Typical Performance Curves (Continued)
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 7
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
Package Dimensions
8.13–8.89
6.10–6.60
Pin 1
64
13
0.25–0.36
5.08 (Max.)
3.28–3.53
0.38 (Min.) 2.54–3.81
2.54 (Bsc)
(0.86)
0.41–0.51
1.02–1.78
0.76–1.14
8.13–8.89
6.10–6.60
Pin 1
64
13
0.25–0.36
5.08 (Max.)
3.28–3.53
0.38 (Min.) 2.54–3.81
2.54 (Bsc)
(0.86)
0.41–0.51
1.02–1.78
0.76–1.14
7.62 (Typ.)
15° (Typ.)
0.20–0.30
0.20–0.30
10.16–10.80
Through Hole 0.4" Lead Spacing
Surface Mount
Rcommended Pad Layout
(1.78)
(2.54)
(1.52)
(7.49)
(10.54)
(0.76)
8.13–8.89
Note:
All dimensions in mm.
6.10–6.60
8.43–9.90
Pin 1
64
13
0.25–0.36
2.54 (Bsc)
(0.86)
0.41–0.51
1.02–1.78
0.76–1.14
0.38 (Min.)
3.28–3.53
5.08
(Max.) 0.20–0.30
0.16–0.88
(8.13)
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 8
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
Ordering Information
Marking Information
Option
Order Entry Identifier
(Example) Description
No option H11L1M Standard Through Hole Device
S H11L1SM Surface Mount Lead Bend
SR2 H11L1SR2M Surface Mount; Tape and Reel
T H11L1TM 0.4" Lead Spacing
V H11L1VM VDE 0884
TV H11L1TVM VDE 0884, 0.4" Lead Spacing
SV H11L1SVM VDE 0884, Surface Mount
SR2V H11L1SR2VM VDE 0884, Surface Mount, Tape and Reel
H11L1
1
2
6
43 5
*Note – Parts that do not have the ‘V’ option (see definition 3 above) that are
marked with date code ‘325’ or earlier are marked in portrait format.
Definitions
1 Fairchild logo
2 Device number
3VDE mark (Note: Only appears on parts ordered with VDE
option – See order entry table)
4 One digit year code, e.g., ‘3’
5 Two digit work week ranging from ‘01’ to ‘53’
6 Assembly package code
V X YY
Q
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 9
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
Tape Dimensions
Note:
All dimensions are in millimeters.
Reflow Profile
4.0 ± 0.1
Ø1.5 MIN
User Direction of Feed
2.0 ± 0.05
1.75 ± 0.10
11.5 ± 1.0
24.0 ± 0.3
12.0 ± 0.1
0.30 ± 0.05
21.0 ± 0.1
4.5 ± 0.20
0.1 MAX 10.1 ± 0.20
9.1 ± 0.20
Ø1.5 ± 0.1/-0
300
280
260
240
220
200
180
160
140
120
100
80
60
40
20
0
°C
Time (s)
0 60 180120 270
260°C
>245°C = 42 Sec
Time above
183°C = 90 Sec
360
1.822°C/Sec Ramp up rate
33 Sec
©2005 Fairchild Semiconductor Corporation www.fairchildsemi.com
H11L1M, H11L2M, H11L3M Rev. 1.0.4 10
H11L1M, H11L2M, H11L3M — 6-Pin DIP Optocoupler
