TCSCS1E226MDCR - Samsung Electro-Mechanics

General Features

Applications

Part Numbering

TC SCS 0J 106 M B A R

●

1●

2●

3●

4●

5●

6●

7●

Tantalum Capacitor ( SCS Series )

The product is smaller version of the SCN series products.

The SCS series have fully molded, compliant lead frame construction designed for use

in applications utilizing solder (Reflow, Wave or Vapor Phase), conductive adhesive or

thermal compression bonding techniques.

Miniaturized tantalum chip capacitors with extended capacitance.

(Reduced size 1/2 to 1/3 in comparison with SCN.)

- Molded Case available in five case codes.

- Compatible with automatic pick and place equipment.

- Meets or Exceeds EIA standard 535BAAC .

- Extended Range Values

- General electronic equipment

- Smoothing Circuit of DC-DC Converters & Output side of AC-DC Converters

- De-Coupling Circuit of High Speed ICs & MPUs

- Various Other High Frequency Circuit Applications

●Abbreviation of Tantalum Capacitor ●Capacitance Tolerance

●Type of Series ●Case size

●Rated Voltage ●Packing

●Capacitance Tolerance ●Packing Polarity

●ABBRIVIATION OF TANTALUM CAPACITOR

●TYPE OF SERIES

●RATED VOLTAGE

●CAPACITANCE

●CAPACITANCE TOLERANCE

●CASE SIZE

The symbol shows the type of the capacitor.

SCS : Samsung environmental Capacitor Standard series

Symbol DC Rated Voltage Symbol DC Rated Voltage

0E 2.5 1C 16

0G 41D 20

0J 6.3 1E 25

1A 10 1V 35

Symbol Capacitance (㎌)Pico Farad (㎊)Symbol Capacitance (㎌)PicoFarad (㎊)

105 1.0 10×105684 0.68 68×104

106 10.0 10×106475 4.7 47×105

Symbol Tolerance(%) Symbol Tolerance(%)

K±10 M±20

Case EIA Code Case EIA Code

J1608 C6032

P2012 D7343

A3216

B3528

●PACKING

●PACKING POLARITY

APPEARANCE AND DIMENSON

Taping and

Reel for Chip

Direction

of Feed

Tape

+ Polarit

Mark

RTaping and

Reel for Chip

Direction

of Feed

+ Polarity Mark

LBulk B

Symbol Packing Code

A7inch

C13 inch

Code EIA Code DIMENSION (mm)

L W1W2H Z

P2012 2.0 ±0.2 1.25 ±0.2 0.9 ±0.1 1.2 MAX 0.5 ±0.2

A3216 3.2 ±0.2 1.6 ±0.2 1.2 ±0.1 1.6 ±0.2 0.8 ±0.3

B3528 3.5 ±0.2 2.8 ±0.2 2.2 ±0.1 1.9 ±0.2 0.8 ±0.3

C6032 6.0 ±0.3 3.2 ±0.3 2.2 ±0.1 2.5 ±0.3 1.3 ±0.3

D7343 7.3 ±0.3 4.3 ±0.3 2.4 ±0.1 2.8 ±0.3 1.3 ±0.3

W1 ZZ

●Standard value and Case size

▶SCS Series

▶SCS-P Series

RELIABILITY T ES T CONDITIO N

-55±2℃, 240±8hrsCapacitance change : within ±10%

Tan δ, LC : initial spec.

Storage at Low Temperature

85±2℃, Surge voltage

Charge 30±5s -> Discharge 5.5±0.5min

1000cycle

Charge discharge resiste r :33Ω

Capacitance change : within ±5 %

Tan δ, LC : initial spec.

Surge withstanding

Voltage

1 cycle condition

(Min. operating temperature →25℃

→Max. operating temperature →25℃)

5 cycle test

Capacitance change : within ±5%

Tan δ, LC : initial spec

Temperature Cycling

With the rated voltage(85℃)

Max. operating temperature(125 ℃)

2000/-0hrs

Capacitance change : within ±10%

Tan δ:initial spec

LC : 125% or less specified initial value

High Temperature Resistance

100k㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified valueImpedance (Z) & ESR

120㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified valueTan δ(DF)

120㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified toleranceCapacitance

19.6N, for 5±1 secNo peeling shall be occur on the terminal

electrode

Adhesion Strength

From -55℃to 125℃,"-55℃: △C/C -10~0%

"+85℃: △C/C 0~10%

"+125℃: △C/C 0~15%

Temperature

Characteristics

The rated DC voltage shall be applied to

terminals across the test capacitor

charge Time: 5 min.

0.01CV or 0.5㎂whichever is greaterLeakage current

Solder pot : 260±5℃, 10±1sec.Capacitance change : within ±15%

Tan δ, LC : initial spec.

Resistance to Soldering heat

SnAg3.0Cu0.5 solder

:245+/5℃, 3±0.3sec

(preheating : 80~120℃for 10~30sec.)

More than 95% of terminal surface is to be

soldered newly

Solderability

Bending to the limit (3mm)

with 1.0mm/sec.

Within specified tolerance

Tan δ, LC : initial spec.

Electrode Strength

40±2℃, 90~95%RH, 500+8/-0hrsCapacitance change : within ±10%

Tan δ, LC : initial spec.

Moisture Resistance

Amplitude : 1.5mm

From 10Hz to 55Hz (return : 1min.)

2hours ´3 direction (x, y, z)

Capacitance change : within ±5%

Tan δ, LC : initial spec.

Vibration Test

Test conditionPerformanceItem

Reliability Test and Judgment Condition 1

RELIABILITY T ES T CONDITIO N

85±2℃, Surge voltage

Charge 30±5s -> Discharge 5.5±0.5min

1000cycle

Charge discharge resiste r :33Ω

Capacitance change : within ±30%

Tan :150% or less specified initial value

LC : initial spec.

Surge withstanding

Voltage

-55±2℃, 240±8hrsCapacitance change : within ±30%

Tan :150% or less specified initial value

LC : initial spec.

Storage at Low Temperature

1 cycle condition

(Min. operating temperature →25℃

→Max. operating temperature →25℃)

5 cycle test

Capacitance change : within ±30%

Tan :150% or less specified initial value

LC : 200% or less specified initial value

Temperature Cycling

With the rated voltage(85℃)

Max. operating temperature(125 ℃)

2000/-0hrs

Capacitance change : within ±30%

Tan :150% or less specified initial value

LC : 125% or less specified initial value

High Temperature Resistance

100k㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified valueImpedance (Z) & ESR

120㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified valueTan δ(DF)

120㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified toleranceCapacitance

19.6N, for 5±1 secNo peeling shall be occur on the terminal

electrode

Adhesion Strength

From -55℃to 125℃,"-55℃: △C/C -25~0%

"+85℃: △C/C 0~20%

"+125℃: △C/C 0~20%

Temperature

Characteristics

The rated DC voltage shall be applied to

terminals across the test capacitor

charge Time: 5 min.

0.01CV or 0.5㎂whichever is greaterLeakage current

Solder pot : 260±5℃, 10±1sec.Capacitance change : within ±30%

Tan :150% or less specified initial value

LC : 200% or less specified initial value

Resistance to Soldering heat

SnAg3.0Cu0.5 solder

:245+/5℃, 3±0.3sec

(preheating : 80~120℃for 10~30sec.)

More than 95% of terminal surface is to be

soldered newly

Solderability

Bending to the limit (3mm)

with 1.0mm/sec.

Within specified tolerance

Tan δ, LC : initial spec.

Electrode Strength

40±2℃, 90~95%RH, 500+8/-0hrsCapacitance change : within ±30%

Tan :150% or less specified initial value

LC : 200% or less specified initial value

Moisture Resistance

Amplitude : 1.5mm

From 10Hz to 55Hz (return : 1min.)

2hours ´3 direction (x, y, z)

Capacitance change : within ±15%

Tan δ, LC : initial spec.

Vibration Test

Test conditionPerformanceItem

Reliability Test and Judgment Condition 2

RELIABILITY T ES T CONDITIO N

85±2℃, Surge voltage

Charge 30±5s -> Discharge 5.5±0.5min

1000cycle

Charge discharge resiste r :33Ω

Capacitance change : within ±5 %

Tan δ, LC : initial spec.

Surge withstanding

Voltage

-55±2℃, 240±8hrsCapacitance change : within ±10%

Tan δ, LC : initial spec.

Storage at Low Temperature

1 cycle condition

(Min. operating temperature →25℃

→Max. operating temperature →25℃)

5 cycle test

Capacitance change : within ±5%

Tan δ, LC : initial spec

Temperature Cycling

With the rated voltage(85℃)

Max. operating temperature(125 ℃)

2000/-0hrs

Capacitance change : within ±10%

Tan δ:initial spec

LC : 125% or less specified initial value

High Temperature Resistance

100k㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified valueImpedance (Z) & ESR

120㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified valueTan δ(DF)

120㎐, maximum 1.0Vrms, maximum

1.5Volt D.C, at 25℃

Within specified toleranceCapacitance

19.6N, for 5±1 secNo peeling shall be occur on the terminal

electrode

Adhesion Strength

From -55℃to 125℃,"-55℃: △C/C -15~0%

"+85℃: △C/C 0~15%

"+125℃: △C/C 0~20%

Temperature

Characteristics

The rated DC voltage shall be applied to

terminals across the test capacitor

charge Time: 5 min.

0.01CV or 0.5㎂whichever is greaterLeakage current

Solder pot : 260±5℃, 10±1sec.Capacitance change : within ±15%

Tan δ, LC : initial spec.

Resistance to Soldering heat

SnAg3.0Cu0.5 solder

:245+/5℃, 3±0.3sec

(preheating : 80~120℃for 10~30sec.)

More than 95% of terminal surface is to be

soldered newly

Solderability

Bending to the limit (3mm)

with 1.0mm/sec.

Within specified tolerance

Tan δ, LC : initial spec.

Electrode Strength

40±2℃, 90~95%RH, 500+8/-0hrsCapacitance change : within ±10%

Tan δ, LC : initial spec.

Moisture Resistance

Amplitude : 1.5mm

From 10Hz to 55Hz (return : 1min.)

2hours ´3 direction (x, y, z)

Capacitance change : within ±5%

Tan δ, LC : initial spec.

Vibration Test

Test conditionPerformanceItem

Reliability Test and Judgment Condition 3

RELIABILITY T ES T CONDITIO N

Table 1 : Maximum Dissipation Factor at Specified Temperatures

4030

2030

1513

1015

1715

1217

108

610

3627

1827

6045

3045

1210

812

+125℃(%)+85℃(%)

+25℃(%)-55℃(%)

Maximum Dissipation Factor, %

0.125CV or 6.25 ㎂

whichever is greater

0.1CV or 5 ㎂

whichever is greater

0.01CV or 0. 5 ㎂

whichever is greater

+125℃(㎂)+85℃(㎂)-55℃(㎂)

Specified

initial value

Maximum DC Leakage Current, ㎂

Table 2 : Maximum DC Leakage Current at Specified Temperatures

PACKAGING

●MARKING

▶P,R CASES

Capacitance Range 1 DIGIT 2 DIGIT

<1.0

㎌A Small Letter A Small Letter

1.0㎌≤ Cap.< 10㎌A Capital Letter A Small Letter

≥10㎌A Capital Letter A Capital Letter

【Code Reference】

㎌46.3 10 16 20

0.22 gj jj aj cj

0.33

0.47 gs js as cs ds

0.68 gw jw aw cw dw

1.0 Ga Ja Aa Ca

1.5

2.2 Gj Jj Aj Cj

3.3 Gn Jn An

4.7 Gs Js As Cs

6.8 Gw Jw

10 GA JA AA

22 GJ JJ

AA AA

Polarity (White)

Rated Voltage

(G:4V J:6.3V A:10V C:16V D:20V)

Capacitance Code

(A:1.0 E:1.5 J:2.2 N:3.3 S:4.7 W:6.8)

[SCS series] [SCL series]

PACKAGING

●MARKING

▶A,S CASES

▶B,T CASES

▶C,D CASES

Polarity (White)

25V

Capacitance Code in ㎌

Rated Voltage

10V AA A336 33

10V

Capacitance Code in ㎌

Polarity (White)

[SCN,SCS,SCE series] [SCL series]

A336 AA

Polarity (White)

Rated Voltage

(G:4V J:6.3V A:10V C:16V D:20V E:25V V:35V)

Capacitance Code in ㎊

A336

[SCN,SCS,SCE series] [SCL, series]

●EMBOSSED PLASTIC TAPE

Right hand

Orientation available

Embossed

Carrier

The tantalum chip capacitors shall be packaged

in tape and reel form for effective use.

- Tape : Semitransparent embossed plastic

- Cover tape : Attached with press, polyester

- The tension of removing the cover tape,

F=10∼70g

Embossed

D2P0P1P2

Removal speed

50mm/sec

15˚

Cover Tape

●REEL DIMENSION

Case Size

reference 180mm(7") reel 330mm(13") reel

J4,000pcs -

P3,000pcs -

A,B 2,000pcs 8,000pcs

C,D 500pcs 2,500pcs

Tape

Width A±2

(±0.079) NMin. C±0.5

(±0.020) D±0.5

(±0.020) B±051

(±0.020) t+0.5

(±0.020) R

8mm ø178

(7) ø50

(1.969) ø13

(0.512) ø21

(0.827) 2

(0.079)

(0.394) 2

(0.079) 0.99

(0.039)

12mm 14

(0.551)

8mm ø330

(13) ø80

(3.150) ø13

(0.512) ø21

(0.827) 2

(0.079)

(0.394) 2

(0.079) 0.99

(0.039)

12mm 14

(0.551)

▶The voltage derating factor should be as great as possible. Under normal conditions, the operating

voltage should be reduced to 50% or less of the rating. It is recommended that the operating

voltage be 30% or less of the rating, particularly when the tantalum capacitors are used in a low-

impedance circuit (see Figs. 1, 2, and 3).

▶For circuits in which a switching, charging , discharging, or other momentary current flows, it is

recommended that the operating voltage be 30% or less of the rating, with a resistor connected in

series to limit the current to 300 mA or less.

▶When the tantalum capacitors are to be used at an ambient temperature of higher than 85℃, the

recommended operating range shown in Fig. 3 should not be exceeded.

APPLICATION MANUAL

●OPERATING VOLTAGE

The operational attentions to the use of the tantalum capacitors are as follows:

- Electrical

- Environmental

- Conditions for mounting on equipment and circuit boards

- Mechanical vibration, shock

If the tantalum capacitors are used without satisfying any one of these conditions, the probability of

short-circuiting, leakage current, ignition or other problems to occur increases. To avoid such

problems, observe the following precautions when using the tantalum capacitors.

Power

supply

circuit

Fig. 1

Power supply filter

Fig. 2

Power supply bypass

OPERATING TEMPERATURE

-40-20020406085100125

-55

100

●RIPPLE

The maximum permissible ripple voltage and current are related to the ratings case size.

Please consult us detail in formations.

▶Ripple Current

The maximum permissible ripple current, IMAX, is calculated as follows :

ESR(f)

PMAX

IMAX =

where:

IMAX : Maximum permissible capacitor ripple current (Arms).

PMAX : Maximum permissible capacitor power loss (W).

Varies with the ambient temperature and case size.

Calculated according to Table

ESR(f): Capacitor equivalent series resistance (Ω).

Since the ESR(f) value varies with the ripple frequency, however, the following correction must be

made in accordance with the operating frequency (see Fig. 4).

ESR(f) = K·ESR(120)

K : Coefficient for the operating frequency (Fig. 4).

ESR(120) = Tan δ·Xc = 2πfC

Tan δ

where:

ESR(120) : Equivalent series resistance at 120 Hz (Ω).

Xc : Capacitive reactance at 120 Hz (Ω).

C : Electrostatic capacitance at 120 Hz (μF).

f : Operating frequency (Hz).

Table.1 Maximum permissible power loss values (PMAX) by case size

Ambient

temperature (℃)PMAX

(W)

J P A B C D

25 0.015 0.015 0.030 0.030 0.030 0.050

55 0.010 0.010 0.019 0.019 0.019 0.032

85 0.005 0.005 0.010 0.010 0.010 0.018

Frequency K

120 1.0

400 0.8

1k 0.65

10k 0.50

20k 0.45

40k 0.43

100k 0.40

1M 0.35

0.01

0.1

1.0

100 1K 10K 100K 1M

FREQUENCY(Hz)

.4 Correction Coefficient

(

)

Table.2 Hz VS K

▶Ripple Voltage

If an excessive ripple voltage is applied to the tantalum capacitors, their internal temperature

rises due to Joule heat, resulting in the detriment of their reliability.

▷The tantalum capacitors must be used in such a conditions that the sum of the Working Voltage

and ripple voltage peak values does not exceed the rated voltage (Fig. 5)

▷Ensure that an reverse voltage due to superimposed voltages is not applied to the capacitors.

▷The maximum permissible ripple voltage varies with the rated voltage. Ensure that ripple voltage does

not exceed the values shown in Figs 6 and 7. If, however, the capacitors are used at a high

temperature, the maximum permissible ripple voltage must be calculated as follows:

Vrms(at 55℃) = 0.7 x Vrms(at 25℃)

Vrms(at 85℃) = 0.5 x Vrms(at 25℃)

Vrms(at 125℃) = 0.3 x Vrms(at 25℃)

Fig.7 Maximum permissible ripple voltage

(

C,D

)

Frequency(Hz)

100

110 100

50V

35V

25V

20V

16V

10V

6.3/7V

2.5V

Fig.6 Maximum permissible ripple voltage

(P,A,B)

Frequency(Hz)

100

110 100

50V

35V

25V

20V

16V

10V

6.3/7V

2.5V

Solid tantalum capacitors are polarized device and may be permanently damaged or destroyed, if

connected with the wrong polarity.

▷The tantalum capacitors must not be operated and change d in reverse mode. And also the

capacitors must not be used in an only AC circuit.

▷The tantalum capacitor dielectric has a rectifying characteristics. Therefore, when a reverse

voltage is applied to it, a large current flows even at a low reverse voltage.As a result,it may

spontaneously generate heat and lead to shorting.

▷Make sure that the polarity and voltage is correct when applying a multi-meter or similar testing

instrument to the capacitors because a reverse voltage or overvoltage can be accidentally

applied.

▷When using the capacitors in a circuit in which a reverse voltage is applied, consult your local

SAMSUNG ELECTRO-MECHANICS agent. If the application of an reverse voltage is

unavoidable, it must not exceed the following values.

At 20°C: 10% of the rated voltage of 1 V, whichever smaller.

At 85°C: 5% of the rated voltage or 0.5 V, whichever smaller.

●REVERSE VOLTAGE

●RELIABILITY O F T ANTALUM CAPACITORS

▶General

The failure rate of the tantalum capacitor varies with the digression ratio, ambient tempe rature, circuit

resistance, circuit application, etc.

Therefore, when proper selectio ns are made so as to afford additional margins, higher reliability can

be derived from the tantalum capacitors. Some examples of actual failure rates are presented below

for your reference.

▶Failure Rate Cal culation Formula

The tantalum capacitors are designed to work at their basic failure

rates shown in Table 3 that prevail when the rated voltage is applied for 1000 hours at 85℃.

Table 3 B asic f ailure rat e

▷Failure rate calculation formula

λuse = λ85 x KVxK

λuse : Estimated capacitor failure rate under the operating conditions.

λ85 : Basic failure rate (Table 3)

KV : Failure rate correction coefficient by the ambient temperature and derating factor.

KR : Failure rate correction coefficient by the circuit resistance,

which is the series-connected resistance divided by the voltage applied to the capacitor.

This resistance is connected in series when the power supply side is viewed from the capacitor side.

K(derating factor)=operating voltage/rated voltage

Standard typeSCN

Small typeSCS

Low profile typeSCL

Ultra-Miniature type(0603)SCM

Low ESR typeSCE

1%/1000h

Face-down typeSCF

Basic failure rateClassificationTYPE

●RELIABILITY PREDICTION

Solid tantalum capacitors exhibit no degration failure mode during shelf storage and show a constantly

decreasing failure rate(i.e. , absence of wearout mechanism) during life tests. this failure rate is

dependent up on three important application conditions:DCvoltage, temperature, and circuit impedance.

Estimates of these respective effects are provided by the reliability nomograph.(Figure 8.)

The nomograph relates failure rate to voltage and temperature while the table relates failure rate to

impedance. These estimates apply to steady-state DC condition, and they assume usage within all

other rated conditions.

Standard conditions, which produce a unity failure rate factor, are rated voltage, +85℃, and 0.1 ohm-

per-volt impedance.

While voltage and temperature are straight-forward, there is sometimes difficulty in determining

impedance. What is required is the circuit impedance seen by the capacitor. If several capacitors are

connected in parallel, the impedance seen by each is lowered by the source of energy stored in the

other capacitors. Energy is similarly stored in series inductors.

Voltage "de-rating" is a common and useful approach to improved reliability. It can be persued too far,

however , when it leads to installation of higher voltage capacitors of much larger size.

It is possible to lose more via higher

inherent failure rate than is gained by

voltage derating. SAMSUNG typically

recommends 50% derating, especially in

low impedance circuits.

Failure rate is conventionally expressed in

units of percent per thousand hours. As a

sample calculation, suppose a particular

batch of capacitors has a failure rate of

0.5% / Khr under standard conditions.

What would b e t he p re dict ed f ailure rate at

0.7times rated voltage, 60℃and 0.6Ω/V?

The nomgraph gives a factor of 7 ×10-2 and

the tabl e giv e s a fa ct or of 0 .4 .

The failure rate estimate is then :

0.5 ×7 ×10-2 ×0.4

= 1.4 ×10-2 or 0.014%/Khr

TFV

Connect the temperature

and applied voltage ratio

of interest with a straight

edge. The multiplier of

failure rate is given at the

inersection of this

line with the model scale.

Given T1&v1 Read Failure

Rate Multiplier F1

Given T, & F2

Read Reguired Voltage V2

Given F3 & V3

Read Allowable Temp T3

120

110

100

-1

-2

-3

-4

-5

1.0

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

Fig.8 Reliability Nomograph

●MOUNTING PRECAUTIONS

Circuit Impedance

(ohms/volt) Failure Rate Impedance

(multiplying factor)

0.1 1.0

0.2 0.8

0.4 0.6

0.6 0.4

0.8 0.3

1.0 0.2

2.0 0.1

3orgreater 0.07

Table 4 Circuit Impedance Reliability Factors

▶Limit Pressure on Capacitor Installation with Mounter

A capacitor that has been damaged should be discarded to avoid later problems resulting from

mechanical stress.

Pressure must not exceed 4.9 N with a tool end diameter of 1.5mm when applied to the

capacitors using an absorber, centering tweezers, or the like. An excessively low absorber setting

position would result in not only the application of undue force to the capacitors but capacitor and

other component scattering,circuit board wiring breakage, and / or cracking as well, particularly

when the capacitors are mounted together with other chips having a height of 1 mm or less.

▶Flux

▷Select a flux that contains a minimum of chlorine and amine.

▷After flux use, the chlorine and amine in the flux remain and must therefore be removed.

▶Recommended Soldering Pattern Dimensions

Pattern

Capacitor

Fig. 9

Table 4 Recommended soldering pattern dimensions(mm)

▶Chip Soldering Temperature and Time

Capacitors are capable of withstanding the following soldering temperatures and conditions;

▷Waved soldering

Capacitor body temperature : 230℃∼ 260℃

Time : 5 seconds or less

▷Reflow solderin g see figures

100

200

100 200 300

Time (sec)

Cooling

260℃Max

Temp.

℃

Pre-heating

Heating

400

3.82.62.34.37.3D,W

2.42.42.33.25.8C,V

1.42.21.62.83.5B,T

1.21.21.61.63.2A,S

0.81.11.21.252.0P,R

0.71.00.90.851.6J,Q,K

zyxWL

Pattern dimensions

Capacitors size

Dimensions

Case

※Recommend Temperature : 235℃~ 245℃

(With Pb-free products, if used under 235℃, the quality confirmation must be needed.)

▷Soldering with a soldering iron

The use of a soldering iron should be avoided wherever possible. If it is

unavoidable, follow the instructions set forth in Table 5. The time of soldering with an iron

should be one.

Table 5

▶Cleaning afte r Mounting

The following solvents are usable when cleaning the capacitors after mounting. Never use

a highly active solve nt .

- Halogen organic solvent (HCFC225, etc.)

- Alcoholic solvent (IPA, ethanol, etc.)

- Petroleum solvent, alkali saponifying agent, water, etc.

Circuit board cleaning must be conducted at a temperature of not higher than 50°C and for

an immersion time of not longer than 30 minutes. When an ultrasonic cleaning method is

used, cleaning must be conducted at a frequency of 48 kHz or lower, at an vibrator output

of 0.02 W/cm3, at a temperature of not higher than 40°C, and for a time of 5 minutes or shorter.

NOTE 1: Care must be exercised in cleaning process so that the mounted capacitor will not come

into contact with any cleaned object or the like or will not get rubbed by a stiff brush or

the like. If such precautions are not taken particularly when the ultrasonic cleaning

method is employed, terminal breakage may occur.

NOTE 2: When performing ultrasonic cleaning under conditions other than stated above, conduct

adequate advance checkout.

●OTHER

▷For further details, refer to EIAJ RCR-2368, Precautions and Guidelines for Using Electroni c Device

Tantalum Capacitors.

▷If you have any questions, feel free to contact your local SAMSUNG ELECTRO-MECHANICS agent.

30 W MAX

Solderi n g-iro n p ow er

3 sec MAX

Time

350℃MAX

Solderi ng-iro n tip t emp erat ure

All case

Type